Temperature-sensitive membranes prepared from blends of poly(vinylidene fluoride) and poly(N-isopropylacrylamides) microgels

In this study, temperature-sensitive membranes were prepared by phase transition of the mixture of the temperature-sensitive poly(N-isopropylacrylamides) (PNIPAAM) microgels and poly(vinylidene fluoride). The results of Fourier transformed infrared spectrometer, X-ray photoelectron spectroscopy, elemental analysis, and scanning electron microscope photographs indicate that the PNIPAAM microgels are distributed more in the inner membrane than on the surface. The scanning electron microscope photographs reveal the blend membranes having porous surfaces with nanometer sizes and porous cross-sections with micrometer sizes. The addition of the PNIPAAM microgels is found to improve the porosity, the pore size, water flux, as well as to enhance the hydrophilicity and anti-fouling property of the blend membranes. The blend membrane shows temperature-sensitive permeability and protein rejection with the most dramatic change at around 32 °C which is the lower critical solution temperature of PNIPAAM, when water or bovine serum albumin solution flow through. Specifically, below 32 °C, the blend membrane shows a high protein rejection ratio which decreases with increasing temperature and a low water flux which increases with increasing temperature; above 32 °C, the blend membrane shows a low protein rejection ratio which decreases with increasing temperature and a high water flux which increases with increasing temperature.     

Fluorescence studies on volume phase transition in poly(acrylamide) and poly(N-isopropylacrylamide) gels

The changes in microenvironments during the volume phase transition of poly(acrylamide) and poly(N-isopropylacrylamide) gels induced by pH change or the change in solvent composition were studied by using dansyl or pyrenyl fluorescent probes.     

Characteristics of a liposome immunoassay on a poly(methyl methacrylate) surface

Liposome immunoassay (LIA) is based on enzyme immunoassay (EIA) but the detection sensitivity could be significantly enhanced by using antibody-coupled immunoliposomes encapsulating HRP (horse radish peroxidase). Here, we applied LIA to non-porous poly(methyl methacrylate) (PMMA) and polystyrene (PS) surfaces to compare its detection sensitivity with that of EIA, using rabbit IgG (a ligand molecule) and anti-rabbit IgG antibody (a capture molecule) as the model system. LIA developed much stronger color signals than EIA, especially at a lower concentration range (< ca. 1 μg mL⁻¹). PMMA showed higher affinity toward rabbit IgG than the PS surface, and the anti-rabbit IgG antibody adsorbed on PMMA was more stable than that on PS. Furthermore, the effects of spot volume and antibody concentration on the signal density were analyzed. The signal density increased as the antibody concentration increased, but it was not significantly affected by the spot volume (2.5–20 μL). In conclusion, LIA on PMMA as a solid support is a very useful, highly sensitive microarray detection system. Sang Youn Hwang and Yoichi Kumada have same rights on this paper.     

Fluorescence probe studies on the complexation between poly(methacrylic acid) and poly(N, N-diethylacrylamide)

The complexation between poly(methacrylic acid) (PMAA) and poly(N, N-diethylacrylamide) (PDEAM) in aqueous phase was studied by UV-vis and fluorescence probe techniques. It was demonstrated that the complexation of PMAA with PDEAM occurs within a pH range of 1-6.5 and along with the complexation, the conformation of PMAA changed from a hypercoiled to a loose coiled form. The complex ratio between the two polymers is 1:1 (PMAA:PDEAM, in monomer unit). Salt effect studies showed that the complexation occurred due to formation of hydrogen bonds between the two polymers. Based upon these conclusions and the "compact micelle-like structure" for PMAA at low pH, a "ladder" model was proposed for the structure of PMAA-PDEAM complex formed at low pH.     

In vitro enzymatic degradation of nanoparticles prepared from hydrophobically-modified poly(gamma-glutamic acid)

Amphiphilic poly(gamma-glutamic acid) (gamma-PGA) was prepared by the introduction of L-phenylalanine ethylester (L-PAE) as a side chain. This gamma-PGA-graft-L-PAE formed monodispersed nanoparticles in water. The particle size of the gamma-PGA nanoparticles could be controlled by the degree of L-PAE grafting. The hydrolytic degradation and enzymatic degradation by gamma-glutamyl transpeptidase (gamma-GTP) of these gamma-PGA nanoparticles was studied by gel permeation chromatography (GPC) and scanning electron microscopy (SEM). The hydrolysis ratio of gamma-PGA was found to decrease upon increasing the hydrophilicity of the gamma-PGA. The degradation of the gamma-PGA backbone by gamma-GTP resulted in a dramatic change in nanoparticle morphology. With increasing time, the gamma-PGA nanoparticles reduced in size and finally disappeared completely.Time-course of the changes in the morphology of the gamma-PGA nanoparticles following incubation with gamma-glutamyl transpeptidase.     

Interactions in water of alkyl and perfluoroalkyl surfactants with fluorocarbon- and hydrocarbon-modified poly(N-isopropylacrylamides)

Fluorescence spectroscopy and isothermal titration calorimetry (ITC) have been used to study the interactions in water at 25 degrees C of two anionic surfactants--sodium dodecyl sulfate (SDS) and sodium perfluorononanoate (SPFN)--with various pyrene-labeled hydrophobically modified poly(N-isopropylacrylamides) (HM-PNIPAM) grafted at random with small amounts of fluorocarbon chains (1H,1H-perfluorooctyl, CH2C7F15); (PNIPAM-F), or (n-octadecyl, C18H37) (PNIPAM-HPy) or both (PNIPAM-F/HPy). In aqueous solution, the copolymers form micellar structures consisting of a loose corona of hydrated poly(N-isopropylacrylamide) chains and a hydrophobic core rich in hydrocarbon or fluorocarbon groups. From fluorescence studies based on changes in the ratio of pyrene excimer to monomer emission intensity, it has been established (1) that mixed SDS/C18H37 clusters form along the polymer chain upon addition of SDS to either PNIPAM-HPy or PNIPAM-F/HPy and (2) that SPFN does not interact with the hydrocarbon-rich microdomains of the polymeric micelles. The conclusions were corroborated by ITC experiments, which yield the overall enthalpy change associated with polymer/surfactant interactions. They provided strong evidence (1) that SDS molecules adsorb along the PNIPAM main chain but do not mix with the fluorocarbon-rich microdomains of PNIPAM-F or PNIPAM-F/HPy and (2) that SPFN associates with the perfluorocarbon substituents of PNIPAM-F and PNIPAM-F/HPy but has a poor affinity for the polymer chain.     

Fluorescence studies of interactions of ionic surfactants with poly(amidoamine) dendrimers

The pyrene fluorescence measurements have been carried out for the micelle formation of sodium dodecyl sulfate (SDS), dodecyltrimethylammonium bromide (DTAB), and dimethylene bis(dodecyldimethylammonium bromide) (12-2-12) in the presence of fixed different amounts of various generations of poly(amidoamine) (PAMAM). The critical micelle concentration (cmc) of SDS decreases with an increase in the fixed amount of PAMAM, suggesting the facilitation of micellization due to the participation of SDS-PAMAM complex in the micelle formation. This behavior has not been observed for DTAB/12-2-12 in the presence of various generations of PAMAM. The results indicate that SDS always has stronger interactions with all the generations of PAMAM in comparison to those of DTAB and 12-2-12.     

Fluorescence depolarization studies of micro-brownian relaxations of poly (methyl methacrylate) in solution

Fluorescence depolarization and quenching measurements have been used to study motions of poly(methyl methacrylate) in toluene at 298 K. Data concerning segmental motion of the polymer chain have been obtained using both an “ideal” label which cannot move independently of the macromolecule and a label in which independent motion should not result in depolarization of radiation. The results compare favourably. Motions affecting the ester group and terminal macromolecular segments also have been studied. The use of naphthalene derivatives as labels of limited bulk has been made possible by the use of dynamic quenching.     

Preparation of hydrophobically-modified acrylamide copolymers using poly(ethylene imine) as a photoinitiator and its performance evaluation in Bohai oilfield

This paper presents copolymers of acrylamide, N,N-dimethyl-N-vinylnonadecan-1-ammonium chloride and N-(2,4-dimethylpentan-2-yl) acrylamide synthesized by photopolymerization using modified poly(ethylene imine) as initiator in water. These hydrophobically modified acrylamide copolymers were dissolved in the brine that was used in enhanced oil recovery in Bohai oilfield. It was found that when the content of N-(2,4-dimethylpentan-2-yl) acrylamide and N,N-dimethyl-N-vinylnonadecan-1-ammonium chloride were 0.1 mol % and 0.3 mol %, respectively, the resulting polymer could meet the demand of solution time and the polymer mechanical shear stability required in Bohai oilfield. The solution properties of synthesized copolymers were compared with the hydrophobically modified polymer currently used in enhanced oil recovery in Bohai oilfield.     

疏水化聚N-异丙基丙烯酰胺胶束的极性

利用Kamlet-Taft溶致变色比较法,在确定了二种探针化合物的峰值波数与溶剂的溶致变色参数表达式的基础上,研究了一系列不同疏水化修饰的聚N-异丙基丙烯酰胶类共聚物水溶液胶束的极性肝（π）和氢键供体能力（α）．结果发现,在摩尔投料比相同时,随着共聚物中丙烯酸酯烷基链的增长,共聚物水溶液胶束的π越来越小,α越来越大;在共聚物组成相同时,随着丙烯酸酯投料比的增大,共聚物水溶液波束的π也呈现相同的情况,而α则无明显的规律．对此现象作了讨论．     

Fluorescence and viscometry study of complexation of poly(acrylic acid) with poly(acrylamide) and hydrolysed poly(acrylamide)

Interpolymer complexation of poly(acrylic acid) with poly(acrylamide) and hydrolysed poly(acrylamide) was studied by fluorescence spectroscopy and viscometry in dilute aqueous solutions. Changes in chain conformation and flexibility due to the interpolymer association are reflected in the intramolecular excimer fluorescence of pyrene groups covalently attached to the polymer chain. Both poly(acrylamide) and hydrolysed poly(acrylamide) form stable complexes with poly(acrylic acid) at low pH. The molecular weight of poly(acrylic acid) and solution properties such as pH and ionic strength were found to influence the stability and the structure of the complexes. In addition, the polymer solutions mixing time showed an effect on the mean stoichiometry of the complex. The intrinsic viscosity of the solutions of mixed polymers at low pH suggested a compact polymer structure for the complex.     

Miscibility of poly(butyl methacrylate-CO-methacrylic acid) or poly(styrene-CO-methacrylic acid) with poly(styrene-CO-4-vinylpyridine) or poly(butyl methacrylate-CO-4-vinylpyridine)

The miscibility of blends of copolymers of different compositions of butyl methacrylate-co-methacrylic acid or styrene-co-methacrylic acid with styrene-co-4-vinylpyridine or butyl methacrylate-co-4-vinylpyridine was studied by differential scanning calorimetry (DSC) and Fourier transform infrared (FTIR) spectroscopy. It was found that these blends were miscible in part as a result of specific favorable interactions between the carboxylic acid and pyridine groups within the polymer chains. Evidence of such interactions was obtained from the single composition-dependent glass transition temperature and the FTIR results.     

Fluorescence self-quenching of a mannosylated poly(p-phenyleneethynylene) induced by concanavalin A

We report that static quenching of a mannosylated conjugated polymer (sugar-PPE) by Concanavalin A is positively dependent upon sugar-PPE concentration, that is, the recorded Stern-Volmer constants increase with increasing sugar-PPE concentration. Comparison with data obtained from isothermal titration calorimetry (ITC) display the increased sensitivity of the quenching method when compared to ITC. The proposed mechanism suggests the interaction of two or more chains of PPE with one Con A molecule leading to a quenched sugar-PPE-Con A construct.     

Rendering poly(amidoamine) or poly(propylenimine) dendrimers temperature sensitive

The poly(amidoamine) dendrimers having terminal isobutyramide (IBAM) groups were prepared by the reaction of isobutyric acid and the amine-terminated poly(amidoamine) dendrimers with generations (G) of 2 to 5 by using a condensing agent, 1,3-dicyclohexylcarbodiimide. 1H and 13C NMR revealed that an IBAM group was attached to essentially every chain end of the dendrimers. While the IBAM-terminated G2 dendrimer was soluble in water, the IBAM-terminated G3, G4, and G5 dendrimers exhibited the lower critical solution temperatures (LCSTs) at 75, 61, and 43 degrees C, respectively. Because the density of the terminal IBAM groups in the periphery of the dendrimer progressively increases with increasing dendrimer generation, the interaction of the IBAM groups might take place more efficiently, resulting in a remarkable decrease in the LCST. In addition, attachment of IBAM groups to poly(propylenimine) dendrimers could give the temperature-sensitive property, indicating that this is an efficient method to render dendrimers temperature sensitive.     

Phase separation studies on poly(vinylidene fluoride) and poly(methyl methacrylate) quenched blends

A combined study by SAXS and DSC on quenched blends of PVDF and PMMA is presented. Attention is focused on the first stage of the phase separation process during annealing that is shown to be mainly determined by the diffusion of the PVDF molecules from the amorphous blend phase towards the crystals growth front. The experimental monomer diffusion constants at T > T_g are compared with those expected theoretically using the approximation of the fast model process and the WLF equation for the relaxation frequency of the monomer. The nature and composition of the crystal interphase are discussed in terms of the SAXS invariant for the whole system and the calorimetric data derived from the T_g transitions observed.     

Thermogravimetric studies on poly(methyl methacrylate), poly(tetrahydrofuran) and their blends

TG studies are given for PMMA prepared by radical polymerization, PTHF prepared by cationic polymerization, and their blends. A procedure is proposed for determining the activation energy, frequency factor, and the order of events corresponding to the respective stages of the multistage TG curves. The order of the initial event of PMMA is not the 1st. It is shown for this discussion that the relationship between mass loss and time of the 2nd order reaction is similar to that of the depolymerization including the vaporization process at the earlier times. Some of TG curves of PTHF are not dependent on the heating rate. This independence depends on the size of sample. The order of event of PTHF, which is obtained from TG curves dependent on the heating rate, is the 0th. The event order equal to the 0th reflects major contribution of vaporization in the event. The TG behaviors shown by the procedure mentioned above for the PMMA/PTHF blends with the smaller PMMA or PTHF contents cancel those of PMMA or PTHF. This revised version was published online in July 2006 with corrections to the Cover Date.     

Crystallite damage studies on irradiated poly(vinylidene fluoride)

The effect of γ-radiation on crystallite of poly(vinylidene fluoride) was studied with X-ray diffraction, differential scanning calorimetry and polarizing macroscopy techniques. It has been shown that the degree of crystallite damage relates to the imperfection of crystallites. The lower the imperfection of crystallite, the stronger the radiation-induced crystallite damage. The long period, lamellae thickness, contour and optical anisotropy of sheprulites in irradiated samples remains unchanged. “Crystallite core damage mechanism” gives a more satisfactory explanation of the results.