MOF‐on‐MOF: Oriented Growth of Multiple Layered Thin Films of Metal–Organic Frameworks

The precise alignment of multiple layers of metal–organic framework (MOF) thin films, or MOF‐on‐MOF films, over macroscopic length scales is presented. The MOF‐on‐MOF films are fabricated by epitaxially matching the interface. The first MOF layer (Cu₂(BPDC)₂, BPDC=biphenyl‐4,4′‐dicarboxylate) is grown on an oriented Cu(OH)₂ film by a “one‐pot” approach. Aligned second (Cu₂(BDC)₂, BDC=benzene 1,4‐dicarboxylate, or Cu₂(BPYDC)₂, BPYDC=2,2′‐bipyridine‐5,5′‐dicarboxylate) MOF layers can be deposited using liquid‐phase epitaxy. The co‐orientation of the MOF films is confirmed by X‐ray diffraction. Importantly, our strategy allows for the synthesis of aligned MOF films, for example, Cu₂(BPYDC)₂, that cannot be grown on a Cu(OH)₂ surface. We show that aligned MOF films furnished with Ag nanoparticles show a unique anisotropic plasmon resonance. Our MOF‐on‐MOF approach expands the chemistry of heteroepitaxially oriented MOF films and provides a new toolbox for multifunctional porous coatings.     

Photo-electrochemical and photocatalytic properties of chemically-treated and thermally-annealed titanium dioxide films

Chemical treatment followed by thermal annealing of titanium dioxide nanoparticle film surfaces with urea or ammonium acetate were found to exert a profound influence on their photoelectrochemical or photocatalytic activity. These films were dip-coated over conducting substrates, then dipped in urea or ammonium acetate aqueo us solutions, and finally baked at 300 or 500°C to yield two sets of chemically-treated TiO₂ (CT-TiO₂) films. The incident photon to electron conversion efficiency (IPCE) of the CT-TiO₂ films in the near-UV region was significantly higher compared to the pristine (untreated) TiO₂ samples baked similarly at 300 or 500°C. Higher photocurrents for formate photo-oxidation were also observed for the CT-TiO₂ samples relative to their untreated TiO₂ counterparts. All the CT-TiO₂ films showed better photocatalytic activity toward Cr(VI) reduction with respect to their untreated TiO₂ counterparts. The enhanced performance of the CT-TiO₂ films was attributed to morphological changes as seen in scanning electron microscopy images. Possible reasons for the performance improvement in terms of better charge carrier separation properties of the CT-TiO₂ films are finally discussed.     

Effect of substrate on phase formation and surface morphology of sol-gel lead-free KNbO3, NaNbO3, and K0.5Na0.5NbO3 thin films

Environmentally acceptable lead-free ferroelectric KNbO₃ (KN) or NaNbO₃ (NN) and K_0.5Na_0.5NbO₃ (KNN) thin films were prepared using a modified sol-gel method by mixing potassium acetate or sodium acetate or both with the Nb-tartrate complex, deposited on the Pt/Al₂O₃ and Pt/SiO₂/Si substrates by a spin-coating method and sintered at 650°C. X-ray diffraction (XRD) analysis indicated that the NN and KNN films on the Pt/SiO₂/Si substrate possessed a single perovskite phase, while NN and KNN films on the Pt/Al₂O₃ substrate contained a small amount of secondary pyrochlore phase, as did KN films on both substrates. Scanning electron microscopic (SEM) and atomic force microscopic (AFM) analyses confirmed that roughness R _q of the thin KNN/Pt/SiO₂/Si film (?? 7.4 nm) was significantly lower than that of the KNN/Pt/Al₂O₃ film (?? 15 nm). The heterogeneous microstructure composed of small spherical and larger needle-like or cuboidal particles were observed in the KN and NN films on both substrates. The homogeneous microstructure of the KNN thin film on the Pt/SiO₂/Si substrate was smoother and contained finer spherical particles (?? 50 nm) than on Pt/Al₂O₃ substrates (?? 100 nm). The effect of different substrates on the surface morphology of thin films was confirmed.     

Effect of biphase on dielectric properties of Bi-doped lead strontium titanate thin films

Pb_0.4Sr_0.6TiO₃ (PST) thin films doped with various concentration of Bi were prepared by a sol-gel method. The phase status, surface morphology and dielectric properties of these thin films were measured by X-ray diffraction (XRD), scanning electron microscopy (SEM) and impedance analyzer, respectively. Results showed that the thin films with the maximum dielectric constant and minimum dielectric loss were obtained for x=0.15. For x<0.15, only pure PST perovskite phase were in the thin films. For 0.2<x<0.4, the PST/Bi₂Ti₂O₇ biphase were obtained. The thin films with pure Bi₂Ti₂O₇ pyrochlore phase were obtained for x=0.67. The biphase thin films had high tunability and high figure of merit (FOM). The FOM of PST/Bi₂Ti₂O₇ biphase thin film was about 6 times higher than that thin films formed with pure perovskite phase or pure pyrochlore phase.     

Vapor‐Surface Sol‐Gel Deposition of Titania Alternated with Protein Adsorption for Assembly of Electroactive,Enzyme‐Active Films

Combining vapor‐surface sol‐gel deposition of titania with alternate adsorption of oppositely charged iron heme proteins provided ultrathin {TiO₂/protein}_n films with reversible voltammetry extended to 15 TiO₂/protein bilayers, more than twice that of more conventional polyion‐protein or nanoparticle‐protein films made by alternate layer‐by‐layer adsorption. Catalytic activity toward O₂, H₂O₂, and NO was also improved significantly compared to the conventionally fabricated films. The method involves vaporization of titanium butoxide into thin films of water, forming porous TiO₂ sol‐gel layers. Myoglobin (Mb), hemoglobin (Hb), and horseradish peroxidase (HRP) were assembled by adsorption alternated with the vapor‐deposited TiO₂ layers. Improved electrochemical and catalytic performance may be related to better film permeability leading to better mass transport within the films, as suggested by studies with soluble voltammetric probes, scanning electron microscopy (SEM) and atomic force microscopy (AFM). The electrochemical and electrocatalytic activity of the films can be controlled by tailoring the amount of water with which the metal alkoxide precursor vapor reacts and the number of bilayers deposited in the assembly.     

Antibacterial glass films prepared on metal surfaces by sol–gel method

This paper describes the preparation and characterization of glass films consisting of SiO₂, Li₂O, Na₂O, K₂O or MgO in varying compositions on stainless steel and aluminum substrates by sol–gel method. Silver phosphate or silver incorporated zeolite was also introduced into the sols for obtaining antibacterial effect. The SiO₂/Li₂O/Na₂O system having the composition of 85:5:10 wt% was found as the optimum for obtaining a stable sol and film formation. The films were investigated by scanning electron microscopy (SEM) and electron dispersive analysis by X-ray (EDX), Fourier transformed infrared (FTIR) spectroscopy, thermo-gravimetric analysis (TGA) and differential thermal analysis (DTA). Homogenous films having 300 ± 20 nm thicknesses were formed by spin coating and then by curing at 500 °C for 1 h. Obtained films had high adherence to the metal substrates and they were also durable in acidic, basic or NaCl environments. They also presented a powerful antibacterial effect against E. coli.     

Useful and accessible organometallic precursors for preparation of zinc sulfide and indium sulfide thin films via solution pyrolysis (printing) method

Polycrystalline β-zinc sulfide thin films were prepared by solution pyrolysis of an ethylzinc isopropylthiolate–zinc bis(dibutyldithiocarbamate) combined precursor (EtZnSiPr–Zn(S₂CNnBu₂)₂) in chloroform solution on glass or silicon(111) substrates at 300°C. Homogeneous but amorphous indium sulfide thin films were obtained from butylindium bis(isopropylthiolate) (nBuInSiPr₂) in P-xylene on these substrates at 300°C similarly. The sulfide thin films obtained were characterized by means of X-ray photoelectron spectroscopy (XPS), X-ray fluorescence Microanalysis, scanning electron microscopy (SEM) and optical band gap measurements.     

Photocrosslinking of poly(2,3-epithiopropyl methacrylate) by the oxidation of pendant episulfide groups

In the photocrosslinking of poly(2,3-epithiopropyl methacrylate) (PETMA) films the effect of the pendant episulfide group's oxidation on the crosslinking of PETMA was investigated. Thermal crosslinking of PETMA is promoted by peroxides such as benzoyl peroxide and hydrogen peroxide. IR spectrum of the crosslinked PETMA showed that the reaction proceeded through the oxidation of episulfide groups by the peroxides. The anthracene (An) sensitized photocrosslinking of PETMA films also proceeded via the oxidation of episulfide groups by singlet oxygen. It was found that residual tetrahydrofuran (THF) in the films remarkably increased the rate of the photocrosslinking and/or reduced the induction period. From the further investigation concerning casting solvents it was found that residual CS₂, CCl₄, and CHCl₃ in films increased the rate of the photocrosslinking and/or reduced the induction period of the photocrosslinking. The disappearance rate of An in the films was also increased by the presence of residual CS₂, CCl₄, and CHCl₃, differring from the result of THF. These results were explained by a difference in lifetime of singlet oxygen in the films. From the results were explained by a difference in lifetime of singlet oxygen in the films. From the results concerning the effects of hydroperoxides such as THF hydroperoxide and t-butyl hydroperoxide on the photocrosslinking of PETMA films the acceleration effect of the residual THF was deduced to be due to the promotion of singlet oxygen-oxidation of sulfide groups by protic compounds such as THF hydroperoxide and H₂O in the THF.     

Nanostructured ZrO2 and Zr‐C‐N Coatings from Chemical Vapor Deposition of Metal‐Organic Precursors

Nanocrystalline zirconium carbonitride (Zr‐C‐N) and zirconium oxide (ZrO₂) films were deposited by chemical vapor deposition (CVD) of zirconium‐tetrakis‐diethylamide (Zr(NEt₂)₄) and ‐tert‐butyloxide (Zr(OBu^t)₄), respectively. The films were deposited on iron substrates and characterized by scanning electron microscopy (SEM), X‐ray diffraction (XRD) and X‐ray photoelectron spectroscopy (XPS). The Zr‐C‐N films show blue, golden brown or bronze colours, with colour stability depending upon the precursor composition (pure metal amide or mixed with Et₂NH). The deposition temperature showed no pronounced effect on the granular morphology of the Zr‐C‐N films. The XRD data of the films correspond to the formation of carbonitride phase whereas the XPS analyses revealed a strong surface oxidation and incorporation of oxygen in the film. The films deposited using a mixture of Zr(NEt₂)₄ and Et₂NH showed higher N content, better adhesion and scratch resistance when compared to films obtained from the CVD of pure Zr(NEt₂)₄. Subject to the precursor composition and deposition temperature (550‐750 °C), the microhardness values of Zr‐C‐N films were found to be in the range 2.11‐5.65 GPa. For ZrO₂ films, morphology and phase composition strongly depend on the deposition temperature. The CVD deposits obtained at 350 °C show tetragonal ZrO₂ to be the only crystalline phase. Upon increasing the deposition temperature to 450 °C, a mixture of tetragonal and monoclinic modifications was formed with morphology made up of interwoven elongated grains. At higher temperatures (550 and 650 °C), pure monoclinic phase was obtained with facetted grains and developed texture.     

Ferroelectric and piezoelectric properties of nylon 11/poly(vinylidene fluoride) bilaminate films

The ferroelectric and piezoelectric properties of a new class of polymer ferroelectric and piezoelectric materials, nylon 11/polyvinylidene fluoride (PVF₂) bilaminate films, prepared by a co-melt-pressing method, is presented. The bilaminate films exhibit typical ferroelectric D-E hysteresis behavior with a remanent polarization, P_r, of about 75 mC/m², which is higher than the value of 52 mC/m² observed for PVF₂ or nylon 11 films measured under the same conditions. The coercive field, E_c, of the bilaminate films is ～ 78 MV/m, which is higher than that of either PVF₂ or nylon 11 films. Measurements of the temperature dependence of the piezoelectric strain coefficient, d₃₁, and the piezoelectric stress coefficient, e₃₁, were also carried out. The bilaminate films exhibit a piezoelectric strain coefficient, d₃₁, of 41 pC/N at room temperature, which is significantly higher than the PVF₂ films (25 pC/N) and the nylon 11 films (3.1 pC/N). When the temperature is increased to 110°C, d₃₁ of the bilaminate films reaches a maximum value of 63 pC/N, more than five times that of PVF₂ (11 pC/N) and more than four times that of nylon 11 (14 pC/N) at the same temperature. The piezoelectric stress coefficient, e₃₁, of the bilaminate films shows a value of 109 mC/m² at room temperature, almost twice that of the PVF₂ films (59 mC/m²) and about 18 times that of the nylon 11 films (6.2 mC/m²). Measurement of the temperature dependence of the hydrostatic piezoelectric coefficient, d_h, of the bilaminate films also shows an enhancement with respect to the individual components, PVF₂ and nylon 11. ©1995 John Wiley & Sons, Inc.     

Study of the properties of in situ Pt-doped SnO2 thin films prepared by metal-organic chemical vapour deposition

Pt-SnO₂ thin films were directly deposited by MOCVD in the temperature range 320–440°C using the reactive gas mixture SnEt4/O₂/Pt(hfa)₂ (hfa being bis(1,1,1,5,5,5-hexafluoroacetylacetonato). The Pt content of the films increases by increasing either the Pt(hfa)₂ mole fraction or the growth temperature. Platinum is uniformly incorporated through the thickness of the films although a small excess was found on the surface. In as-deposited films, Pt is in the metallic form on the surface whereas it is mainly in the form of PtO in the bulk of the layers. Pt doping decreases the resistivity by more than an order of magnitude and improves the thermal stability of the films. The detection sensitivity to ethanol in dry air of in situ Pt-doped SnO₂ is significantly enhanced compared to undoped layers. Another beneficial effect of Pt doping is the lowering of the optimum detection temperature of ethanol.     

Effects of UV-irradiation on the formation of oxide thin films from chemically modified metal-alkoxides

The effects of UV-irradiation on the properties of ZrO₂ and TiO₂ gel films prepared from corresponding metal-butoxides modified with acetylacetone (AcAc) or benzoylacetone (BzAc) have been studied. It was found that the chelate bonds of -diketones remaining in the gel films were dissociated by the UV-irradiation. The UV-irradiation also changed the properties of the gel films such as solubility; the solubility in acidic solutions was decreased for ZrO₂ gel films modified with AcAc and TiO₂ gel films modified with BzAc became insoluble in alcohol. Based on these findings, a new fine-patterning process has been established, which enables us to make fine-patterns of ZrO₂ and TiO₂ films on a variety of substrates.     

Electron Probe Microanalysis of HfO2 Thin Films on Conductive and Insulating Substrates

Quantitative electron probe microanalysis of highly insulating materials is a complicated problem, partially solved by coating samples with grounded thin conductive layers or using novel scanning electron microscopy (SEM) techniques, such as low-voltage and/or variable pressure SEM. In this work, some problems of quantitative X-ray microanalysis of thin HfO₂ films, in particular the possibility to determine mass thickness correlated to the density of the layer material, are discussed. For comparison, Al₂O₃, Ta₂O₅ and TiO₂ films grown onto both semiconductive Si and insulating quartz substrates were also analysed. All the films studied were synthesized by atomic layer deposition method.     

Surface analysis of films and film systems produced by pulsed laser deposition

Ceramic films and film systems (ZrO₂ films, ZrO₂/Ti multilayers, and BN films) are deposited by pulsed laser deposition (PLD) and analyzed using X-ray photoelectron (XPS), Auger electron (AES), and micro-Raman spectroscopies. The electron spectroscopies are used to determine the film stoichiometry, the nature of the bonding, and to specify contaminant species. The micro-Raman spectroscopy gives information on crystal structure, grain size, and mechanical stress within the films. In ZrO₂ films a stoichiometry is achieved with typically 5%, with only weak dependencies on processing variables. The only contaminants are a small amount of water from the ambient gas and a carbonaceous surface layer. Multilayers consisting of alternating ZrO₂ and Ti layers exhibit a TiC contamination within the Ti layers. Depending on the processing variables, BN films may be nearly stoichiometric or may have significant, even dominant contaminations throughout the film from elemental B, B₂O₃, and/or a boron-oxynitride species. The first component is due to the non-stoichiometric material removal from the target (N-depletion) at low laser fluences, as confirmed by XPS measurements on irradiated targets. The second and third arise from H₂O in the ambient, and exhibit a complex dependence on processing variables. Micro-Raman spectra show only amorphous or hexagonalphase BN. Depending on the position on the substrate relative to the laser-induced vapour/plasma plume, there may be a particle deposition or mechanical stress within the films, as evidenced from large shifts (up to 15 cm^–1) of the Raman spectral peaks.     

Synthesis of Free-Standing Crystalline Barium Titanate Films at Vapor/Liquid or Liquid/Liquid Interface

Synthesis of free-standing crystalline barium titanate (BaTiO₃) films at vapor/liquid or liquid/liquid interface at room temperature has been investigated. High concentration Ba, Ti alkoxides precursor solution (1.2 mol/l) or pre-hydrolyzed precursor solutions by water vapor in a H₂O/Ba molar ratio of 0 to 6 were used as dropping solutions at the interfaces. Transparent gel films were formed when partially hydrolyzed precursors (H₂O/Ba = 2 to 3) were spread out on a N₂/liquid paraffin interface. The films shrank from syneresis and vaporization of the solvent during aging at room temperature. As a result, free-standing transparent films with a thickness of around 1 m and little stoichiometric deviation were obtained by separation from the liquid surface and rinse by hexane. The films consisted of crystalline BaTiO₃ particles of less than a few nanometers. Nanostructured dense BaTiO₃ free-standing films with a grain size less than 100 nm were obtained at 1030°C.     

IR Spectroscopic Investigations of Gasochromic and Electrochromic Sol-Gel—Derived Peroxotungstic Acid/Ormosil Composite and Crystalline WO3 Films

We studied the gasochromic effect of amorphous peroxopolytungstic acid (W-PTA), W-PTA (ormosil) and crystalline WO₃ films. These latter films were prepared after a heat treatment of W-PTA/ormosil films at 450°C. The ormosil served as a template, providing the monoclinic WO₃ films with adequate porosity. The spill-over effect was attained by impregnating the porous WO₃ crystalline films with H₂PtCl₆ followed by a heat treatment at 380°C. The amorphous films became gasochromic with the addition of PdCl₂ to the corresponding W-PTA and W-PTA/ormosil sols.Structural features of all the films were studied with the help of infrared (IR) spectroscopy and transmission electron microscopy (TEM). In situ IR spectra of the films, performed in the presence of reducing (H₂/Ar) and oxidising (O₂/Ar) gases, revealed a reversible transformation of the monoclinic to the tetragonal H _x WO₃ phase. At the same time the coloration (reduction) of the amorphous films was accompanied by the formation of coordinated water molecules and increased numbers of W=O bonds. Gasochromic colouring/bleaching changes and the corresponding kinetics were assessed from in situ UV-visible transmission measurements on the films.     

Chemical characterization of plasma-polymerized films from acetylene and nitrogen-containing mixtures and their ethanol vapor sensitivity

In this study, plasma-polymerized thin films were prepared from plasma enhanced chemical vapor deposition (PECVD) of acetylene (C₂H₂), acetylene/nitrogen (C₂H₂/N₂), or acetylene/ammonia (C₂H₂/NH₃). When N₂ or NH₃ was mixed with C₂H₂ in the feed, the films were identified to contain all elements of the mixture and the properties of the films were implied by the C–H bonds and nitrogen functionalities. As shown by X-ray photoelectron spectroscopy (XPS) the [N]/[C] atomic ratio varies by changing the mixture composition and reaches a maximum of 0.12 for mixing C₂H₂ with NH₃. It is found that the resistance of the thin film sensors prepared from C₂H₂, C₂H₂/N₂, and C₂H₂/NH₃ is distinctly decreased by over 2 orders of magnitude by the adsorption of ethanol vapor.     

Oxygen permeability of surfactant/polymer composite films with multibilayer and inverted hexagonal structure

The permeability of oxygen through horizontally oriented multibilayer films of polyion complexes prepared from quaternary ammonium-type surfactants [CH₃(CH₂)_n-1]₂N⁺(CH₃)₂Br^?(n = 14, 16, 18), and poly(p-styrenesulfonate) or poly[2-(acrylamido)-2-methyl-1-propanesulfonate], was measured in water using an oxygen electrode. The permeability depended mainly on the phase of the multibilayers. Thus, it increased abruptly (about 10-fold) near each phase transition temperature because of the fluidity enhancement of the multibilayer. Inverted hexagonal type nonbilayer films prepared from the polyion complexes and cholesterol had greater permeability (2–20-fold) than the multibilayer films in both phases. The large permeability of the nonbilayer films was attributed to the lack of a barrier such as the bilayer and lower crystallinity of the films. It was associated neither with an increase in thermal movement of the lipid surfactant molecules nor with an increase in the water content of the films by the addition of cholesterol. © 1993 John Wiley & Sons, Inc.     

Aerosol-Gel Deposition of Optically Active Thin Films in the System Y2Ti2O7-Er2Ti2O7

Optically active thin films in the system Y₂Ti₂O₇-Er₂Ti₂O₇ (YETO) have been deposited using the Aerosol-gel process. Depending on the heat-treatment temperature, amorphous or crystalline films could be prepared in the range 600–950°C. The study shows that dilution of erbium ions within a Y₂Ti₂O₇ (YTO) matrix allows to prevent short range distance interactions between those ions and to promote good photoluminescence properties of YETO films. These properties are discussed and compared with those of sol-gel derived silica films doped with erbium.     

Electrodeposition of thin Cu<Subscript>2</Subscript>ZnSnS<Subscript>4</Subscript> films

The electrochemical behavior of copper(II), zinc(II), and thiosulfate (S₂O₃ ^2-) ions on the molybdenum electrode in individual 0.2 М sodium sulfate solutions (рН 6.7) and with addition of either 0.1 М tartaric acid (рН 4.6) or 0.1 М citric acid (рН 4.7) is studied. A one-step electrochemical method is developed for the deposition of thin Cu₂ZnSnS₄ films, which is carried out on the molybdenum electrode at a constant potential in sodium sulfate solutions containing tartaric acid. The effect of the concentration of electrolyte components on the chemical composition of Cu₂ZnSnS₄ films is determined. The phase composition is confirmed by the Raman spectroscopy data. The surface morphology of synthesized films is studied by means of scanning-electron and atomic-force microscopes. The photoelectrochemical characteristics of Cu₂ZnSnS₄ films are determined. Samples of these coatings on the Mo electrode are found to be highly photosensitive.