Effects of surface microstructure of hydroxyapatite on protein adsorption and biological performance of osteoblasts

The aim of this study was to investigate the effect of surface microstructure on the serum protein adsorption and the biological performance of osteoblasts cultured in vitro, when seeded onto the surface of ceramics with different grain size: conventional HA, micron-sized HA and nano-sized HA. Sodium dodecylsulfate-polyacrylamide gel electrophoresis (SDS-PAGE) was used to comparatively analyze the protein adsorption solution. The content of alkaline phosphatase (ALP) was determined, and then by using wash way method, the adhesion ability was tested. XPS tests indicated that the content of N on the surface was significant different between the three groups (P < 0.05). SDS-PAGE analysis indicated that all the materials in these three groups could adsorb a large amount albumin, while the material in the nHA group adsorbed more albumin than the other groups. There were significant differences among them on the levels of osteoblast proliferation and adhesion in vitro. The biocompatibility of nHA is the best and of conventional HA is the worst.     

Fluorination of polymethylmethaacrylate with tetrafluoroethane using DC glow discharge plasma

Fluorination of polymer surfaces has technological applications in various fields such as microelectronics, biomaterials, textile, packing, etc. In this study PMMA surfaces were fluorinated using DC glow discharge plasma. Tetrafluoroethane was used as the fluorinating agent. On the fluorinated PMMA surface, static water contact angle, surface energy, optical transmittance (UV-vis), XPS and AFM analyses were carried out. After the fluorination PMMA surface becomes hydrophobic with water contact angle of 107° without losing optical transparency. Surface energy of fluorine plasma-treated PMMA decreased from 35 mJ/cm² to 21.2 mJ/cm². RMS roughness of the fluorinated surface was 4.01 nm and XPS studies revealed the formation of C-CF_x and CF₃ groups on the PMMA surface.     

Structural and hydrophobic-hydrophilic properties of nanosilica/zirconia alone and with adsorbed PDMS

Two nanosilica A-300/zirconia (SZ) composites at zirconia content CZrO₂=5 and 20 wt.% were synthesized using a wet impregnation method with zirconium acetylacetonate as a precursor. The specific surface area of SZ is larger than that of A-300 because zirconia is composed of nanoparticles (crystallites of 4 nm in average size at CZrO₂=20 wt.%) smaller than those of the initial silica (d_av ≈ 11 nm). A-300 and SZ modified by polydimethylsiloxane (PDMS at molecular weight 1700 and 7960) in amounts of 5, 10, 15, 20 and 40 wt.% remained in the powder state with aggregates of primary particles smaller than those of A-300. SZ is more hydrophilic than silica but PDMS/SZ is more hydrophobic (maximum hydrophobic at C_PDMS 15-20 or 40 wt.%) than PDMS/A-300.     

Surface microstructures and antimicrobial properties of copper plasma alloyed stainless steel

Bacterial adhesion to stainless steel surfaces is one of the major reason causing the cross-contamination and infection in many practical applications. An approach to solve this problem is to enhance the antibacterial properties on the surface of stainless steel. In this paper, novel antibacterial stainless steel surfaces with different copper content have been prepared by a plasma surface alloying technique at various gas pressures. The microstructure of the alloyed surfaces was investigated using glow discharge optical emission spectroscopy (GDOES) and scanning electron microscopy (SEM). The viability of bacteria attached to the antibacterial surfaces was tested using the spread plate method. The antibacterial mechanism of the alloyed surfaces was studied by X-ray photoelectron spectroscopy (XPS). The results indicate that gas pressure has a great influence on the surface elements concentration and the depth of the alloyed layer. The maximum copper concentration in the alloyed surface obtained at the gas pressure of 60 Pa is about 7.1 wt.%. This alloyed surface exhibited very strong antibacterial ability, and an effective reduction of 98% of Escherichia coli (E. coli) within 1 h was achieved by contact with the alloyed surface. The maximum thickness of the copper alloyed layer obtained at 45 Pa is about 6.5 μm. Although the rate of reduction for E. coli of this alloyed surface was slower than that of the alloyed surface with the copper content about 7.1 wt.% over the first 3 h, few were able to survive more than 12 h and the reduction reached over 99.9%. The XPS analysis results indicated that the copper ions were released when the copper alloyed stainless steel in contact with bacterial solution, which is an important factor for killing bacteria. Based on an overall consideration of bacterial killing rate and durability, the alloyed surface with the copper content of 2.5 wt.% and the thickness of about 6.5 μm obtained at the gas pressure of 45 Pa is expected to be useful as antimicrobial materials that may have a promising future in antimicrobial applications.     

Ultrasound-assisted extraction of oleanolic acid and ursolic acid from Ligustrum lucidum Ait

Oleanolic acid and ursolic acid are the main bioactive compounds in fruit of Ligustrum lucidum Ait, which possess anti-inflammatory, antioxidative, antiprotozoal, antimutagenic and anticancer properties. In this study, the ultrasound-assisted extraction of oleanolic acid and ursolic acid from L. lucidum Ait was investigated with HPLC-photodiode array detection. Effects of several experimental parameters, such as type and concentration of extraction solvent, ratio of liquid to material, extraction temperature and extraction time, on extraction efficiencies of oleanolic acid and ursolic acid from L. lucidum were evaluated. The influence of experimental parameters on extraction efficiency of ursolic acid was more significant than that of oleanolic acid. The optimal extraction conditions were 95% ethanol, the ratio of material to liquid at 1:20, and extraction for 10 min at 40 °C under ultrasonic irradiation. Under the optimal conditions, the yields of oleanolic acid and ursolic acid were 6.3 ± 0.25 and 9.8 ± 0.30 mg/g, respectively. The results indicated that the ultrasound-assisted extraction is a very useful method for the extraction of oleanolic acid and ursolic acid from L. lucidum.     

XPS, XRD and SEM characterization of a thin ceria layer deposited onto graphite electrode for application in lithium-ion batteries

Thin ceria layer deposited by electro-precipitation onto graphite was synthesised and characterized by X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and scanning electron microscopy (SEM). The electro-precipitated ceria has a cubic structure with nanocrystallites of about 6 nm. The SEM analyses shows that the ceria layer reflects the morphology of the graphite electrode, exhibits small cracks usually found on the electro-precipitated films but covers almost completely the surface of the graphite. The ceria layer is composed of 75% Ce(IV) and 25% Ce(III) oxides as indicated by the XPS analyses. Cyclic voltammetry and galvanostatic charge-discharge tests in ethylene carbonate/dimethyl carbonate (1/1) (wt/wt) in the presence of 1 M LiPF₆ show that reversible lithium insertion and deinsertion occurs in the graphite/ceria electrode and that the ceria layer on the graphite electrode prevents from the loss of capacity during the first four cycles. The reduction of the electrolyte occurs at about 0.7 V vs Li/Li⁺ on both electrodes but XPS and SEM analyses show that the SEI layer is thin and not as homogenous on the graphite as on the graphite/ceria electrode. The composition of the SEI layer on the graphite/ceria electrode, mainly composed of Li₂CO₃, ROCO₂Li, R-CH₂OLi and LiF, is different than those obtained on the graphite.     

Electroless nickel plating on APTHS modified wood veneer for EMI shielding

A new activation process was developed for electroless plating to prepare wood-based EMI shielding material. Pd(II) was adsorbed on a wood surface modified with γ-aminopropyltrihydroxysilane (APTHS) formed by the hydrolysis of γ-aminopropyltriethoxysilane (APTES). After reduction of Pd(II), electroless plating was successfully initiated and an Ni-P coating was deposited on the wood veneer. The activation process and resulting coating were characterized by XPS, SEM-EDS and XRD. The metal deposition, surface resistivity and electromagnetic shielding effectiveness were measured. XPS analysis proved that Pd(II) was bonded to the amino group of APTHS and was reduced to Pd(0). The Ni-P coating was uniform, compact and continuous, and consisted of 3.39 wt.% phosphorus and 96.61 wt.% nickel. XRD analysis indicated that the coating was crystalline, which is thought to be related to the low phosphorus content. The plated birch veneers exhibited electromagnetic shielding effectiveness greater than 60 dB in the frequency range 10 MHz-1.5 GHz.     

Study of surface interactions of ionic liquids with aluminium alloys in corrosion and erosion-corrosion processes

Surface interactions of alkylimidazolium ionic liquids (ILs) with aluminium alloy Al 2011 have been studied by immersion tests in seven neat ILs [1-n-alkyl-3-methylimidazolium X⁻ (X = BF₄; n = 2 (IL1), 6 (IL2), 8 (IL3). X = CF₃SO₃; n = 2 (IL4). X = (4-CH₃C₆H₄SO₃); n = 2 (IL5). X = PF₆; n = 6 (IL6)] and 1-butyl-3-methylpyridinium bis(trifluoromethylsulfonyl)imide (IL7)]. Immersion tests for Al 2011 have also been carried out in 1 wt.% and 5 wt.% solutions of 1-ethyl,3-methylimidazolium tetrafluoroborate (IL1) in water. No corrosion of Al 2011 by neat ILs is observed. The highest corrosion rate for Al 2011 in water is observed in the presence of a 5 wt.% IL1 due to hydrolysis of the anion with hydrogen evolution and formation of aluminium fluoride. Erosion-corrosion processes have been studied for three aluminium alloys (Al 2011, Al 6061 and Al 7075) in a 90 wt.% IL1 solution in water in the presence of α-alumina particles. The erosion-corrosion rates are around 0.2 mm/year or lower, and increase with increasing copper content to give a corrosion resistance order of Al 6061 > Al 7075 > Al 2011. Results are discussed on the basis of scanning electron microscopy (SEM) observations, energy dispersive spectroscopy (EDS) analysis, X-ray diffraction (XRD) patterns and X-ray photoelectron spectroscopy (XPS) determinations.     

A study on wear resistance and microcrack of the Ti3Al/TiAl + TiC ceramic layer deposited by laser cladding on Ti-6Al-4V alloy

Laser cladding of the Al + TiC alloy powder on Ti-6Al-4V alloy can form the Ti₃Al/TiAl + TiC ceramic layer. In this study, TiC particle-dispersed Ti₃Al/TiAl matrix ceramic layer on the Ti-6Al-4V alloy by laser cladding has been researched by means of X-ray diffraction, scanning electron microscope, electron probe micro-analyzer, energy dispersive spectrometer. The main difference from the earlier reports is that Ti₃Al/TiAl has been chosen as the matrix of the composite coating. The wear resistance of the Al + 30 wt.% TiC and the Al + 40 wt.% TiC cladding layer was approximately 2 times greater than that of the Ti-6Al-4V substrate due to the reinforcement of the Ti₃Al/TiAl + TiC hard phases. However, when the TiC mass percent was above 40 wt.%, the thermal stress value was greater than the materials yield strength limit in the ceramic layer, the microcrack was present and its wear resistance decreased.     

Materials and ion transport property studies on hot-press casted solid polymer electrolyte membranes: [(1 − x) PEO: x KIO3]

Materials and ion transport property characterization in Solid Polymer Electrolyte (SPE) membranes: (1 − x) PEO: x KIO₃, where x = 0, 10, 20, 30, 40, 50 wt.%, have been studied. SPE films have been prepared following two casting techniques: a novel hot-press (extrusion) and the traditional solution cast. Hot-press technique is a completely dry/solvent free/rapid/inexpensive procedure as compared to solution cast method and has recently been receiving wider acceptability to cast membranes of ion conducting polymeric electrolytes.‘Log σ − x’ study revealed σ-maxima at salt concentration x = 30 wt.% for SPE film prepared by both the methods. However, hot-pressed SPE film: 70 PEO: 30 KIO₃ exhibited relatively higher room temperature conductivity (σ ∼ 4.40 × 10^− 7 S cm^− 1) than that of the solution casted film. This has been referred to as Optimum Conducting Composition (OCC) SPE film. Materials characterization in OCC SPE film has been done by XRD, FTIR and DSC techniques. These studies confirmed the complexation of salt in the polymeric host. Some basic ionic parameters viz. conductivity (σ), ionic mobility (μ), mobile ion concentration (n), ionic transference number (t_ion) have been determined using different experimental procedures to understand the ion transport behaviour in OCC SPE material. The temperature dependent conductivity measurement has also been carried out and the activation energy (E_a) has been computed from the linear least square fitting of ‘log σ − 1 / T’ Arrhenius plot.     

Photoinduced effects in γ-glycine nanocrystallites embedded in polymer matrices

We have established a principal role of the polarity of polymer matrices on the piezooptical dispersion of the γ-glycine nanocrystallites embedded into the polymethymethacrylate (PMMA) and polycarbonate (PC) matrices. We found that the optical treatment by bicolor two laser beams at 1064 nm and 532 nm which are originating from the same 10 ns Nd:YAG laser, causes occurrence of the piezooptical effects. The optimal content of the γ-glycine nanocrystallites with respect to the magnitude of piezooptical coefficients was within the range of size 50-80 nm, corresponding to the 6.5 wt.%. We studied relaxation and spectral dependence of the corresponding coefficients of the piezooptic tensor.     

Control of polarization deviation at two separate wavelength by using all dielectric thin film materials

Two separate wavelength 1315 nm and 1550 nm were most widely used in near-infrared spectrum region. Based on a four-layer structure and a symmetry structure, a initial thin film stack system was constructed. Then it was optimized alternately by simplex and conjugate graduate algorithm, a beam splitter with splitting ratio R:T = 50:50 at this two wavelength was gained. The design result showed that the difference between reflectivity of P and S light around wavlength range 1300?1330 nm and 1535?1565 nm at incident angle 40°?50° was all below 2%. That indicated our design controlled the polarization deviation well at two separate wavelength with a reasonable range for both wavelength and incident angle.     

1 Gbit/s transmission over step-index plastic optical fiber using an optical receiver with an integrated equalizer

A single chip optical receiver with an integrated large-diameter photodiode, transimpedance amplifier, two stages active equalizer, post amplifier and 50 Ω driver is used for gigabit transmission over PMMA step plastic optical fiber (SI-POF). The large-diameter photodiode with an antireflection coating optimized for red light. The integrated equalizer enables the presented optical receiver to reach 1 Gbit/s over 50 m SI-POF at bit error ratio of 10^− 6. An error free (< 10^− 9) 1 Gbit/s data rate over 40 m standard PMMA step-index plastic optical fiber is also achieved.     

Surface-modified zeolite-filled chitosan membranes for pervaporation dehydration of ethanol

Surface-modified zeolite-filled chitosan (CS) membranes were prepared by incorporating 3-mercaptopropyltrimethoxysilane (MPTMS)-modified H-ZSM-5 zeolite into chitosan for pervaporation dehydration of aqueous ethanol solution. The physicochemical characterization by XPS, FT-IR, XRD, DMA and SEM showed that -SO₃H group was readily grafted on the surface of H-ZSM-5 with the mediation of MPTMS and hydrogen peroxide, and the accompanying ion-ion interaction between -SO₃H group on surface-modified H-ZSM-5 and -NH₃⁺ group on chitosan substantially eliminated the nonselective voids at the chitosan-H-ZSM-5 interface of the filled membranes. The experimental results also revealed that H-ZSM-5 exhibited desirable size-selective and preferential adsorption effects for aqueous ethanol solution. As a result, modified H-ZSM-5 filled membranes showed higher swelling degree and permeation flux, and improved selectivity for aqueous ethanol solution. In comparison between chitosan control membrane (permeation flux 54.18 g/(m² h) and separation factor 158.02 for 90 wt.% aqueous ethanol solution at 80 °C), the modified H-ZSM-5 filled membrane with 8 wt.% filling content exhibited a remarkably improved pervaporation performance with permeation flux 278.54 g/(m² h) and separation factor 274.46 under the identical experimental condition.     

Electrochemical corrosion behaviors of a-C:H and a-C:NX:H films

The a-C:H and a-C:N_X:H films were deposited onto silicon wafers using radio frequency (rf) plasma enhanced chemical vapor deposition (PECVD) and pulsed-dc glow discharge plasma CVD, respectively. Raman spectroscopy and X-ray photoelectron spectroscopy (XPS) were used to characterize chemical nature and bond types of the films. The results demonstrated that the a-C:H film prepared by rf-CVD (rf C:H) has lower I_D/I_G ratio, indicating smaller sp² cluster size in an amorphous carbon matrix. The nitrogen concentrations of 2.9 at.% and 7.9 at.% correspond to carbon nitride films prepared with rf and pulse power, respectively.Electrochemical corrosion performances of the carbon films were investigated by potentiodynamic polarization test. The electrolyte used in this work was a 0.89% NaCl solution. The corrosion test showed that the rf C:H film exhibited excellent anti-corrosion performance with a corrosion rate of 2 nA cm⁻², while the carbon nitride films prepared by rf technique and pulse technique showed a corrosion rate of 6 nA cm⁻² and 235 nA cm⁻², respectively. It is reasonable to conclude that the smaller sp² cluster size of rf C:H film restrained the electron transfer velocity and then avoids detriment from the exchange of electrons.     

Characterization of Pd-CeOx interaction on α-Al2O3 support

The Pd-Ce interaction was studied over CeO₂ (0.3-2.5 wt.%)-Pd (1 wt.%)/α-Al₂O₃ catalysts used in the reforming reaction of CH₄ with CO₂. The samples were characterized by using high resolution transmission electron microscopy (HRTEM) and X-ray photoelectron spectroscopy (XPS). The activity and selectivity behavior was in good agreement with that of other supported metal catalysts (Ni and Pd) modified with different promoters. The preliminary results of HRTEM would indicate that the CeO_x forms small crystallites around the Pd particle. The XPS analysis for the regions of Ce 3d and Pd 3d, gives an account of Ce being present mostly as Ce³⁺ and a high binding energy for Pd 3d_5/2 (335.3 eV), an evidence of Pd-Ce chemical interaction. The Pd/Al XPS intensity ratios vs. the Pd average particle size, determined by TEM, show an excellent correlation for fresh and used catalyst. These results indicate that the diminution of the Pd/Al ratios was due to Pd sintering. Consequently, the small amounts of CeO_x species do not cover the Pd particle, in agreement with the HRTEM results. The overall results stand for the promoter action mechanism of the CeO_x for the reforming reaction with CO₂.     

Effect of Al on the electrochemical corrosion behaviour of Pb free Sn-8.5 Zn-0.5 Ag-XAl-0.5 Ga solder in 3.5% NaCl solution

The effect of Al on the electrochemical corrosion behaviour of Pb-free Sn-8.5 Zn-0.5 Ag-XAl-0.5 Ga solder in 3.5% NaCl solution was investigated by using potentiodynamic polarization techniques. The X content in the solder varied from 0.1 to 3 wt.%. Polarization studies revealed that an increase in Al content upto 1.5 wt.% decreased the corrosion current density (I_corr), corrosion rate of the solder and shifted the corrosion potential (E_corr) towards more noble values. However, higher content of Al, i.e. 3 (wt.%) in the five-element solder enhanced the corrosion rate and resulted in a significant increase in the E_corr towards more negative values. Passivation behaviour was noticed in all the solders having varying Al content, but the passive film formed at 1.5 wt.% Al was most stable due to its low passivation current density (i_p) and low critical current density (i_cc) value in comparison to the other solders. XPS and Auger depth profile results revealed that the passive film consisted of oxides/hydroxides of Al and Zn formed on the surface of the solder with Sn being formed in the subsequent layer. Considerable aluminium segregation occurred towards the surface principally as Al₂O₃/Al(OH)₃ with increase in Al content to 1.5 wt.% in the five element solder. The formation of Al₂O₃ seemed to prevent the oxidation of zinc on the surface of the solder.     

Light emitting CdS quantum dots in PMMA: Synthesis and optical studies

Freshly prepared CdS-quantum dots (QDs) in DMF (clear pale solution) when loaded in polymethylmethacrylate (PMMA) lead to excellent optical properties. The tuning of the absorption and emission wavelengths via experimentally control parameters is considered novel and significant. The absorption band for CdS was observed at about 370 nm in polymeric matrix. The blue, green and orange light emissions from such composite solution were tuned and stabilized by simply varying the concentration of CdS, cadmium and sulphur in the final product. Photoluminescence (PL) measurement with 2% CdS loading showed band-edge emissions from the composite with only about 20-25 nm Stokes shift in emission wavelength. Observation of such optical properties indicated that the composite has narrow particle size distribution and particle diameter may well be below 10 nm. X-ray diffraction (XRD) patterns of the film with higher loading of CdS showed broad pattern for hexagonal CdS. Thermo-gravimetric analysis (TGA) of CdS/PMMA composite film revealed that it has better thermal stability than PMMA alone. Transmission electron microscopy (TEM) showed agglomerated tiny dots in nano-meter regime.     

Quantitative and high mass ToF-SIMS studies of siloxane segregation in hydrogel polymers using cryogenic sample handling techniques

This paper examines the capabilities of cryogenic sample handling to examine composition and structure of hydrogel materials where siloxane components are central to the analysis. XPS analysis of multicomponent polymers with cryogenic sample handling following exposure to aqueous environments has revealed the composition and kinetics of near surface reorganization for siloxane and fluorocarbon containing polymers. In this study we report results from a ToF-SIMS protocol for cryogenic sample handling applied to the analysis of surface changes upon hydration/dehydration of hydrogel polymers. Comparison of results from angle dependent XPS and ToF-SIMS are discussed for a range of commercial soft contact lens materials. Both methods detected changes in surface chemistry between the hydrated (frozen) and dehydrated surfaces. Analysis of the hydrated surfaces detected polymer components indicative of the commercial formulation as well as ice clusters. Analysis of the dehydrated materials detected changes in surface chemistry relative to the hydrated surface in addition to loss of water due to sample dehydration. A quantitative standard additions method for ToF-SIMS data was used to determine submonolayer amounts of PDMS impurities at the surface of the hydrogels. ToF-SIMS analysis of a series of seven poly (allyl methacrylate-g-dimethylsiloxane), AMA-g-DMS, graft copolymers in the hydrated state revealed high mass oligomeric ion distributions for systems with bulk PDMS content greater than 25 wt.%. This marks the first time that detection of high mass oligomeric ion distributions from hydrated (frozen) surfaces has been reported. Analysis of the dehydrated surface detected formation of high mass oligomeric ion distributions for systems with PDMS bulk content greater than 15 wt.%, but only detected these ion distributions in wet (frozen) samples when the bulk concentration was greater than 25 wt.%.     

Optimization of the ultrasound-assisted extraction of melatonin from red rice (Oryza sativa) grains through a response surface methodology

An analytical ultrasound-assisted extraction (UAE) technique has been optimized and validated for the extraction of melatonin from rice grains. A Box–Behnken design in conjunction with a response surface methodology based on six factors and three levels was used to evaluate the effects of the studied factors prior to optimizing the UAE conditions. The significant (p < 0.05) response surface models with high coefficients of determination were fitted to the experimental data. Solvent composition and extraction temperature were found to have very significant effects on the response value (p < 0.005). The optimal UAE conditions were as follows: extraction time of 10 min, ultrasound amplitude of 30%, cycle of 0.2 s⁻¹, extraction temperature of 40 °C, 50% methanol in water as the extraction solvent at pH 3.5 and a solvent/solid ratio 2.5:1. The method validation ensured right values for linearity, LOD, LOQ, precision and recovery. Furthermore, the method was successfully applied in the analysis of a number of rice samples throughout the rice production process. Hence, it was demonstrated that this particular UAE method is an interesting tool for the determination of melatonin in rice grain samples.