Comparison of palladium-magnesium nitrate and ammonium dihydrogenphosphate modifiers for cadmium determination in honey samples by electrothermal atomic absorption spectrometry

The occurrence of certain trace elements, such as cadmium, in honey bee can be considered as an indication of environmental pollution. In the present work, two methods for Cd determination in honey by electrothermal atomic absorption spectrometry, using palladium-magnesium nitrate and ammonium dihydrogenphosphate as chemical modifiers, have been developed. In none of these cases honey samples required pretreatment. Honey was diluted in water (20% w/v), and hydrogen peroxide, nitric acid, and Triton X-100 were added to minimize the matrix effect. For the first method, 21.6 μg of palladium and 4.5 μg of magnesium were added as chemical modifier; for the second method, 60 μg of ammonium dihydrogenphosphate were employed. The limits of detection obtained were 0.32 ng g⁻¹ for ammonium dihydrogenphosphate method and 0.54 ng g⁻¹ for palladium-magnesium nitrate method. The characteristic mass was 0.7 and 1.0 pg for ammonium dihydrogenphosphate and palladium-magnesium nitrate methods, respectively. The relative standard deviation (<10%) and the analytical recovery (98-105%) were comparable in both methods. The optimised methods were applied to the determination of the cadmium content in unpolluted Galician honey samples. Cd has been detected the analysed samples in the range (n.d.—4.3 ng g⁻¹).     

Simultaneous determination of cadmium and lead in wine by electrothermal atomic absorption spectrometry

A method has been developed for the direct simultaneous determination of Cd and Pb in white and red wine by electrothermal atomic absorption spectrometry (ET-AAS) using a transversely heated graphite tube atomizer (THGA) with longitudinal Zeeman-effect background correction. The thermal behavior of both analytes during pyrolysis and atomization stages were investigated in 0.028 mol l⁻¹ HNO₃ and in 1+1 v/v diluted wine using mixtures of Pd(NO₃)₂+Mg(NO₃)₂ and NH₄H₂PO₄+Mg(NO₃)₂ as chemical modifiers. With 5 μg Pd+3 μg Mg as the modifiers and a two-step pyrolysis (10 s at 400°C and 10 s at 600°C), the formation of carbonaceous residues inside the atomizer was avoided. For 20 μl of sample (wine+0.056 mol l⁻¹ HNO₃, 1+1, v/v) dispensed into the graphite tube, analytical curves in the 0.10–1.0 μg l⁻¹ Cd and 5.0–50 μg l⁻¹ Pb ranges were established. The characteristic mass was approximately 0.6 pg for Cd and 33 pg for Pb, and the lifetime of the tube was approximately 400 firings. The limits of detection (LOD) based on integrated absorbance (0.03 μg l⁻¹ for Cd, 0.8 μg l⁻¹ for Pb) exceeded the requirements of Brazilian Food Regulations (decree #55871 from Health Department), which establish the maximum permissible level for Cd at 200 μg l⁻¹ and for Pb at 500 μg l⁻¹. The relative standard deviations (n=12) were typically <8% for Cd and <6% for Pb. The recoveries of Cd and Pb added to wine samples varied from 88 to 107% and 93 to 103%, respectively. The accuracy of the direct determination of Cd and Pb was checked for 10 table wines by comparing the results with those obtained for digested wine using single-element ET-AAS, which were in agreement at the 95% confidence level.     

Determination of trace impurities in iron and nickel-base alloys by graphite furnace atomic absorption spectrometry

Five approaches to the determination of trace amounts of lead, bismuth, thallium, selenium, tellurium, and silver in iron and nickel-based alloys were investigated. While all procedures produced satisfactory results, direct techniques yielded a significant times advantage over separation schemes. Matrix effects made calibration curves an impractical approach. A spiking technique was used to generate data on a wide range of standard alloy samples.     

Chemical modifiers in the determination of molybdenum in human serum by electrothermal atomic absorption spectrometry

Summary Various modifiers were investigated for the molybdenum determination in human serum samples by electrothermal atomization atomic absorption spectrometry. Methods with magnesium nitrate, barium difluoride, nitric acid, palladium-magnesium nitrate and palladium-hydroxylamine were studied by introducing the serum samples directly into the graphite furnace with 0.2% triton X-100. The mineralisation and atomization curves, the amount of modifier and the calibration and addition graphs were studied in all instances. The characteristic masses were 18, 22, 17, 12 and 13 pg of molybdenum for magnesium nitrate, barium difluoride, nitric acid, palladium-magnesium nitrate and palladium-hydroxylamine, respectively. The precision, accuracy and interferences of the methods were also investigated.     

Chemical modifiers in arsenic determination in biological materials by tungsten coil electrothermal atomic absorption spectrometry

Palladium, iridium, and rhodium are evaluated as possible chemical modifiers in the determination of As in digest solutions of biological materials (human hair and clam) by tungsten coil electrothermal atomic absorption spectrophotometry (TCA-AAS). The modifier in solution was applied onto the coil and thermally pre-reduced; the pre-reduction conditions, the amount of modifier, and the thermal program were optimized. Palladium was not satisfactory, whereas Ir and Rh were effective modifiers and rendered better relative sensitivity for As by a factor of 1.4 and 1.9, respectively compared to the case without modifier. Upon optimization of thermal conditions for As in pre-reduced Ir (2.0 µg) and Rh (2.0 µg) modifiers and in the digest solutions of the study matrices, Rh (2.0 µg) was more effective modifier and was selected as such. The mean within-day repeatability was 2.8% in consecutive measurements (25–100 µg L^–1) (3 cycles, each of n=6) and confirmed good short-term stability of the absorbance measurements. The mean reproducibility was 4.4% (n=20 in a 3-day period) and the detection limit (3 _blank/slope) was 29 pg (n=15). The useful coil lifetime in Rh modifier was extended to 300–400 firings. Validation was by determination of As in the certified reference material (CRM) of Oyster tissue solution with a percentage relative error (E _rel%) of 2% and percentage relative standard deviation (RSD%) of 3% (n=4), and by analytical recovery of As spiked in CRM of human hair [94±8% (n=4)]. The methodology is simple, fast (sample readout frequency 21 h^–1), reliable, of low cost, and was applied to the determination of As in hair samples of exposed and unexposed workers.     

Determination of cadmium in hair and blood by tungsten coil electrothermal atomic absorption spectrometry with chemical modifiers

Three chemical modifiers ((NH(4))(2)HPO(4), NH(4)H(2)PO(4), and Pd as Pd(NO(3))(2)) were evaluated for the determination of Cd in acid-digested solutions of hair and blood using electrothermal atomic absorption spectrometry in a tungsten coil atomizer (TCA). All modifiers caused some thermal stabilization of Cd when compared to the behavior observed in nitric acid medium. The best effects were observed in 15 mug ml(-)(1) Pd medium; the characteristic mass of Cd was 0.3 pg and the method detection limits were 0.009 mug g(-)(1) in hair and 0.2 mug l(-)(1) in blood. In addition to a slight thermal stabilization effect, Pd also increased the sensitivity for Cd by ca. 40% and the tungsten coil lifetime by 20% (i.e. from 300 to 360 heating cycles), reduced background signals, and eliminated condensed phase interferences caused by concomitants. The accuracy (3.2% as mean relative error in the Pd modifier) was checked for the determination of Cd in acid-digested solutions of certified reference materials of human hair and blood and by recoveries of Cd in spiked hair and blood samples by both TCA and a graphite furnace procedure. All results obtained in chemical modifiers are in agreement at a 95% confidence level.     

Nickel and strontium nitrates as modifiers for the determination of selenium in wine by Zeeman electrothermal atomic absorption spectrometry

A mixed matrix modifier of nickel and strontium nitrates was used as a chemical modifier for the determination of selenium in wines by Zeeman electrothermal atomic absorption spectrometry. Wine samples were heated on a boiling water bath with small amounts of nitric acid and hydrogen peroxide. For complete elimination of interference, especially from sulfates and phosphates, selenium is complexed with ammonium pyrolidinedithiocarbamate (APDTC), extracted into methyl isobutyl ketone (MIBK), and measured by ETAAS. The graphite furnace temperature program was optimized for both aqueous and organic solutions. Pyrolysis temperatures of 1300 degrees C and 800 degrees C were chosen for aqueous and organic solutions, respectively; 2700 degrees C and 2100 degrees C were used as optimum atomization temperatures for aqueous and organic solutions, respectively. The optimum modifier mass established is markedly lower than those presented in the literature. The platform atomization ensures pretreatment stabilization up to 1100 degrees C and 1600 degrees C, respectively, for organic and aqueous selenium solutions. The procedure was verified by the method of standard addition. The investigated wine samples originated from the different regions of the Republic of Macedonia. The selenium concentration varied from not detectable to 0.93 microg L(-1).     

Nickel and strontium nitrates as modifiers for the determination of selenium in wine by Zeeman electrothermal atomic absorption spectrometry

A mixed matrix modifier of nickel and strontium nitrates was used as a chemical modifier for the determination of selenium in wines by Zeeman electrothermal atomic absorption spectrometry. Wine samples were heated on a boiling water bath with small amounts of nitric acid and hydrogen peroxide. For complete elimination of interference, especially from sulfates and phosphates, selenium is complexed with ammonium pyrolidinedithiocarbamate (APDTC), extracted into methyl isobutyl ketone (MIBK), and measured by ETAAS. The graphite furnace temperature program was optimized for both aqueous and organic solutions. Pyrolysis temperatures of 1300?°C and 800?°C were chosen for aqueous and organic solutions, respectively; 2700?°C and 2100?°C were used as optimum atomization temperatures for aqueous and organic solutions, respectively. The optimum modifier mass established is markedly lower than those presented in the literature. The platform atomization ensures pretreatment stabilization up to 1100?°C and 1600?°C, respectively, for organic and aqueous selenium solutions. The procedure was verified by the method of standard addition. The investigated wine samples originated from the different regions of the Republic of Macedonia. The selenium concentration varied from not detectable to 0.93 μg L^–1.     

The determination of barium,lanthanum and magnesium in pancreatic islets by electrothermal atomic absorption spectrometry

Barium and lanthanum are determined by direct injection of freeze-dried samples (1–15 μg), and magnesium by injection of 2-μl aliquots of a homogenized suspension. The amounts found are 5.5 (±0.7), 219 (±7) and 28±6 mmol kg^-1 (dry weight) for Ba, La and Mg, respectively.     

Performance of electrodeposited noble metals as permanent modifiers for the determination of cadmium in the presence of mineral acids by electrothermal atomic absorption spectrometry

The analytical performance of electrodeposited noble metals (Pd, Rh or Pd+Rh) on the graphite surface for cadmium determination in the presence of inorganic acids was evaluated and discussed. The study was carried out for 16% HNO₃, 28% HCl and a mixture of both acids (aqua regia). It was demonstrated that all electrodeposited modifiers stabilized cadmium up to 800°C in the presence of HNO₃ and aqua regia. When only HCl was present in the solution the thermal stability of cadmium was less pronounced, the maximum pyrolysis temperature that could be applied was 500°C. The long-term study for Cd determination shows that permanent performance of electrodeposited modifiers is not influenced by mineral acids, moreover, the tube lifetime was doubled, compared with a non-modified tube, when Pd+Rh were electrodeposited onto the graphite surface.     

Determination of cadmium in slurries of marine sediment samples by electrothermal atomic absorption spectrometry using palladium and phosphate as chemical modifiers

A method for the determination of cadmium in slurries of marine sediment using palladium and phosphate as chemical modifier has been optimized. To stabilize the marine sediment slurry, Triton X-100 at 0.1% was used. To obtain a complete pyrolysis of the slurry sample two mineralization steps were used, the first at 480 °C and the second at 600 °C and 700 °C for phosphate and palladium, respectively. The precision and accuracy of the method have been studied by analyzing the Reference Material PACS-1 (marine sediment) of National Research Council Canada. The detection limits (LOD) were 11.9 g kg^–1 for phosphate and 42.0 g kg^–1 when palladium was used. These methods have been applied to the determination of cadmium in marine sediment samples from the Galicia coast and the results of both methods were compared; no significant differences were found between the two procedures.     

Direct determination of cadmium in urine by electrothermal atomic absorption spectrometry after in situ electrodeposition

Determination of cadmium in urine by ETAAS suffers from severe interferences deteriorating the precision and accuracy of the analysis. Electrodeposition step prior to ETAAS allows to avoid interferences and makes cadmium determination possible even at ultratrace levels. The proposed procedures involve electrolytic deposition of cadmium from acidified urine on previously electrolytically deposited palladium film on a graphite atomizer tube, followed by removal of residual solution, pyrolysis and atomization. Both electrodeposition processes take place in a drop of the respective solution (palladium nitrate modifier and acidified urine, respectively), when Pt/Ir dosing capillary serves as an anode and the graphite tube represents a cathode. The voltage is held at −3.0 V. Matrix removal is then accomplished by withdrawal of the depleted sample solution from the tube (procedure A) or the same but followed by rinsing of the deposit with 0.2 mol l⁻¹ HNO₃ (procedure B). The accuracy of both procedures was verified by recovery test. Detection limits 0.025 and 0.030 μg Cd/l of urine were achieved for A and B procedures, respectively. Both procedures are time consuming. The measurement cycle represents 5 and 7 min for A and B procedures, respectively.     

Matrix modification for the direct determination of cadmium in urine by electrothermal atomic absorption spectrometry

Matrix modification with ammonium nitrate, ammonium dihydrogen-phosphate and Triton X-100 proved suitable. Optimization of the graphite furnace parameters allowed cadmium to be quantified at 800°C. The response was 0.1 μgl^-1 for 1% absorption, and the relative standard deviation for consecutive determinations of a urine containing 1.5 μg Cd l^-1 was 4%. Urinary cadmium levels of 0.4–1.8 μg l^-1 were found in five occupationally unexposed persons.     

Direct determination of cadmium in natural waters by electrothermal atomic absorption spectrometry without matrix modification

A procedure for the determination of cadmium in fresh, coastal and estuarine waters by polarized Zeeman-effect graphite-furnace atomic absorption spectrometry is validated by using lake waters and seawater. The limit of detection for freshwaters is <2 ng l^?1 cadmium. Undiluted seawater can be analyzed directly without the addition of matrix modifiers with the aid of a stabilized temperature platform. The instrument is calibrated with diluted NBS SRM 1643a (Trace Elements in Water). Analytical performance was tested extensively with fresh and brackish water samples and procedures were worked out to ensure that a high degree of accurately is achieved consistently.     

Feasibility of employing permanent chemical modifiers for the determination of cadmium in coal using slurry sampling electrothermal atomic absorption spectrometry

Iridium and ruthenium, alone and in combination with tungsten, thermally deposited on the platform of a transversely heated graphite tube, were investigated for their suitability as permanent chemical modifiers for the determination of cadmium in coal slurries by electrothermal atomic absorption spectrometry (ET AAS). The conventional mixed palladium and magnesium nitrates (Pd–Mg) modifiers, added in solution, were also investigated for comparison. The latter one showed the best performance for aqueous solutions, and the mixed W–Ir and W–Ru permanent modifiers had the lowest stabilizing power. All of the investigated modifiers lost some of their stabilizing power when coal slurries were investigated. The Pd–Mg modifier, pure Ir and Ru, and a mixture of 300 μg W + 200 μg Ir could stabilize Cd at least to a pyrolysis temperature of 600 °C, whereas all the other combinations already failed at temperatures above 500–550 °C. Additional investigations of the supernatant liquid of the slurries supported the assumption that the high acid concentration of the slurries and/or a concomitant leaching out of the coal might be responsible for the reduced stabilizing power of the modifiers. The maximum applicable pyrolysis temperature of 600 °C was not sufficient to reduce the background absorption to a manageable level in the majority of the coal samples. High-resolution continuum source ET AAS revealed that the continuous background absorption was exceeding values of A = 2, and was overlapping with the analyte signal. Although the latter technique could correct for this background absorption, some analyte was apparently lost with the rapidly vaporizing matrix so that the method could not be considered to be rugged. A characteristic mass of 1.0 pg and a detection limit of 0.6 ng g^− 1 could be obtained under these conditions.     

Behaviour of chemical modifiers in the determination of arsenic by electrothermal atomic absorption spectrometry in petroleum products

Most comparative studies on the efficiency of chemical modifiers have been conducted in aqueous media. In the present work, we proposed a detailed study of the use of different chemical modifiers for direct determination of arsenic in complex organic matrices by electrothermal atomic absorption spectrometry (ETAAS). Palladium, rhodium, tungsten, silver, lanthanum and a mixture of palladium and magnesium were tested. The figures of merit used for evaluation and comparison were acquired in the optimal conditions for each modifier, established by multivariate optimization of the main variables based on Doehlert designs. Singular features were observed for the chemical behaviour of some modifiers in organic matrices compared to aqueous media, such as the worse performance of Pd + Mg modifier and no notice of severe tube corrosion from La application. Lanthanum was chosen as the best chemical modifier for the present application, according to predefined criteria. Lanthanum showed the minimum limit of detection, characteristic concentration and blank signal among all tested species and no effect of the concomitants usually present in petrochemical feedstocks. Using a 200 mg L⁻¹ lanthanum solution as a chemical modifier, the average relative standard deviations of 7 and 16% (at 3-15 μg L⁻¹ level) and characteristic concentrations of 0.47 and 0.77 μg L⁻¹ for naphtha and petroleum condensates, respectively, were observed.     

Determination of vanadium in mussels by electrothermal atomic absorption spectrometry without chemical modifiers

A method was developed for the quantitative determination of total vanadium concentration in mussels via electrothermal atomic absorption spectrometry (ETAAS). After the microwave digestion of the samples, a program using temperatures of 1600 °C and 2600 °C for ashing and atomization respectively, without any matrix modifiers, allowed us to obtain results that were satisfactory since they agreed closely with certified reference material values. The detection limit was 0.03 mg kg^–1 (dry weight), indicating that the method is suitable for the analysis of mussel samples. This determination was compared with matrix modifiers that have been reported previously. The method was applied to various cultivated and wild mussels from the Galician coast, yielding levels below 1 mg kg^–1 (wet weight).     

Molybdenum, Mo-Ir and Mo-Ru coatings as permanent chemical modifiers for the determination of cadmium and lead in sediments and soil samples by electrothermal atomic absorption spectrometry

Molybdenum, Ir, Ru, Mo-Ir, Mo-Ru thermally coated on to platforms inserted in pyrolytic graphite tubes as permanent modifiers and Pd + Mg(NO₃)₂ conventional modifier mixture have been employed for the determination of cadmium and lead in dissolved sediments and soil samples by electrothermal atomic absorption spectrometry (ETAAS). Optimum masses and mass ratios of permanent modifiers for the analysis of Cd and Pb in sample solutions have been investigated. The 280 μg of Mo, 200 μg of Ir, 200 μg of Ru, 280 μg of Mo + 200 μg of Ir or 280 μg of Mo + 200 μg of Ru has been found as efficient as 5 μg of Pd + 3 μg of Mg(NO₃)₂ for increasing thermal stabilization of analytes and for decreasing the most serious interferences. Pyrolysis and atomization temperatures, atomization and background signal shapes, characteristic masses and detection limits of analytes in dissolved samples with or without permanent and conventional modifiers have been compared. The detection limits and characteristic masses obtained with Mo-Ir coated platform are 0.01 μg g⁻¹ and 1.1 pg for Cd and 0.09 μg g⁻¹ and 19 pg for Pb, respectively. Long-term stabilities for analytes in samples with Mo, Mo-Ir, Mo-Ru and Pd + Mg(NO₃)₂ have been studied. Cadmium and lead contents have been determined in certified and standard reference materials by using optimum conditions investigated and the results obtained with Mo-Ir or Mo-Ru were in agreement with the values of certified reference materials.     

Comparative study of chemical modifiers for the determination of molybdenum in milk by electrothermal atomisation atomic absorption spectrometry

A comparative study of various chemical modifiers for the determination of molybdenum in milk by electrothermal atomisation atomic absorption spectrometry was carried out. Methods with nitric acid or barium difluoride as the chemical modifier and in the absence of a chemical modifier were studied by introducing the milk samples directly into the graphite furnace with octyl alcohol. The graphite furnace programme, amount of modifier and the calibration and additions graphs were studied in all instances. The characteristic masses were 17.82, 18.64 and 12.08 pg of molybdenum in the absence of a chemical modifier and with nitric acid or barium difluoride as the chemical modifier, respectively. The precision, accuracy and interferences of the method were also investigated.     

Rapid determination of lead and cadmium in biological fluids by electrothermal atomic absorption spectrometry using Zeeman correction

Procedures for the electrothermal atomic absorption spectrometric determination of lead and cadmium in urine, serum and blood are developed. For serum and blood, the samples are diluted by incorporating 0.015% (w/v) Triton X-100 and 0.1% (w/v) ammonium dihydrogenphosphate to the solutions, which are then introduced directly into the furnace. A solution containing 15% (w/v) hydrogen peroxide and 0.65% (w/v) nitric acid is also introduced into the atomizer by means of a separate injection. Zeeman-based correction is recommended. Both conventional and fast-heating programs are discussed. Calibration is carried out using the standard additions method. The reliability of the procedures is checked by analyzing three certified reference materials and by recovery studies.