Influence of monomer structure on chemo- and stereoselectivity of 1,3-diene polymerization

MAO/CpTiCl₃ is an active catalyst for the polymerization of various types of 1,3-dienes. Butadiene, (E) - and (Z) −1,3-pentadiene, (E) −2-methyl-1,3-pentadiene and 2,3-dimethylbutadiene yield, at room temperature, polymers with a cis-1,4 or a mixed cis/1,2 structure. 4-Methyl-1,3-pentadiene and (E,E) −2,4-hexadiene give, respectively, a 1,2 syndiotactic and a trans-1,4/1,2 polymer. MAO/CpTiCl₂·2THF and MAO/(CpTiCl₂)_n are less active than the CpTiCl₃ catalyst, but give the same type of polymers. A change of stereospecificity with temperature was observed in the polymerization of (Z)-1,3-pentadiene: a cis-1,4 isotactic polymer was obtained at +20°C, and a crystalline 1,2 syndiotactic polymer at −20°C. This effect was attributed to a different mode of coordination of the monomer, which is cis-η⁴ at +20°C and may be trans-η² at −20°C. Results obtained with catalysts from CpTi(OBu)₃ and Ti(OBu)₄ are reported for comparison. An interpretation is given of the formation of cis-1,4 isotactic poly(2-methylpentadiene) and of 1,2 syndiotactic poly(4-methylpentadiene), as well as of syndiotactic polystyrene.     

Etude structurale du polypentadiene-1,3 par spectrometrie de RMN du 13C

The structure of stereoregular polymers of 1,3-pentadiene was determined by ¹³C-NMR spectroscopy at 22.6 MHz. Not only was it possible to distinguish between cis-1,4 and trans-1,4 but also between isotactic and syndiotactic cis-1,4 structures. Triad effects were detected in the trans-1,2 syndiotactic polypentadiene; 1,4–1,2 as well as 1,4–4,1 linkages were observed.     

Polymerization of 1,3-dienes with neodymium catalysts

Neodymium catalysts are typical for the cis polymerization of 1,3-dienes. The systems prepared from a neodymium-carboxylate, a chlorine donor and A1(i-C₄H₉)₃ are characterized by a low efficiency, only ca. 6% of the neodymium being active in the catalysis. Much more active systems are obtained using allyl derivatives of neodymium in combination with aluminoxanes, in particular with methylaluminoxane (MAO). These systems have the characteristics of a single site catalyst. Evidence suggesting an ionic structure for the catalytic species is reported. Terminally substituted butadienes give polymers with a cis-1,4 isotactic structure, with the exception of (E, E)-2,4-hexadiene, which gives trans-1,4 polymers. An interpretation is reported.     

Chemoselectivity in 4-methyl-1,3-pentadiene polymerization in the presence of homogeneous Ti-based catalysts

The homogeneous catalyst CpTiCl₃-MAO is able to produce a random copolymer of 4-methyl-1,3-pentadiene with ethylene. ¹³C NMR analysis of the copolymers shows that after insertion of ethylene units, the next 4-ymethyl-1,3-pentadiene unit can be inserted in either 1,2 or 1,4 arrangement. The high chemoselectivity observed in the 1,2-syndiotactic homopolymerization of 4-methyl-1,3-pentadiene with respect to the lower one observed in the copolymerization with ethylene is attributed to a back-biting coordination to the Ti of the active species of the penultimate monomer unit of the growing chain.     

Recent advances in the field of diolefin polymerization with transition metal catalysts

Recent advances in the field of catalysis for 1,3-diene polymerization and in the interpretation of the polymerization mechanism are examined. Catalysts prepared from methylaluminoxanes and soluble transition metal compounds are in general more active than the analogous systems prepared from AlR₃. With some catalysts, however, (e.g. lanthanide systems) a high activity is obtained only when transition metal compounds containing preformed metal-carbon bonds are used. Methylaluminoxanes affect also the stereospecificity of the polymerization. Active and stereospecific systems are obtained from monocyclopentadienyl derivatives of Ti and aluminoxanes. Recent views on the factors that determine stereospecificity are examined. Schemes are presented for the formation of iso- or syndiotactic polymers, with 1,2, cis-1,4 or trans-1,4 structure, from various dienes.     

~(13)C-NMR STUDY ON THE CHAIN TERMINAL STRUCTURE OF POLY-1,3-PENTADIENE POLYMERIZED WITH RARE EARTH CATALYST

The sequence distribution and the terminal structures of poly-1,3-pentadiene chains obtained by rare earth catalyst and effect of polymerization temperature on microstructure of the polymer have been investigated by ~(13)C-NMR method. According to experimental results it was supposed that terminal active growing chain of the polymer would be four types of anti- and syn-η~3-allyl structures. When polymerization temperature was reduced, the content of cis-1,4-poly-1,3-pcntadiene increases. It can be explained by isomerization between anti- and syn-η~3-allyl. The process forming trans-1,2 unit instead of 3,4-unit were also described.     

Organometallic polymers containing tricarbonyl(η4-diene)-ruthenium(0) and -iron(0) as pendant groups

Vinyl ethers containing tricarbonyl(14-η⁴-1,3-pentadiene)-ruthenium(0) and -iron(0) species were prepared utilizing selective dienylation with penta-dienylpotassium and were polymerized with cationic initiators to give high molecular weight polymers. The diene-metal moieties were converted into tricarbonyl(13-η³-allyl)metal species by protonation with dry HCl. Tricarbonyl(3-allyl-14-η⁴-1,3-pentadiene)iron(0) also undergoes cationic polymerization but the presence of its isomer, tricarbonyl(3-propenyl-14-η⁴-1,3-pentadiene)iron(0) inhibits the polymerization.     

Linear oligomerization of 1,3-pentadiene in presence of catalytic system CoCl2-PPh3-NaBH4

Conclusions The system CoCl₂-PPh₃₂-NaBH₄ catalyzes the oligomerization of trans-1,3-pentadiene to 4-methyl-2,5,7-nonatriene and the 1,3-pentadiene trimer. 4-Methyl-2,5,7-nonatriene is formed predominantly at 95°, while the trimer is the predominant product at 120°. This system does not catalyze the oligomerization of cis-1,3-pentadiene.Translated from Izvestiya Akademii Nauk SSSR, Seriya Khimicheskaya, No. 6, 1423–1425, June, 1978.     

Donor-Acceptor Complexes in Copolymerization. XXXV. Alternating Diene-Dienophile Copolymers. 3. Copolymerization of cis- and trans-1, 3-Pentadiene with Maleic Anhydride and Acrylonitrile… AlEt1.5CI1.5

Abstract

The copolymerization of the cis or trans isomers of 1,3-pentadiene with maleic anhydride in the presence of a peroxide catalyst yields identical equimolar, alternating copolymers in which the pentadiene units have a cis-1, 4 configuration (IR, NMR). The copolymerization of the cis or trans isomers of 1, 3-pentadiene with acrylonitrile in the presence of ethyl aluminum sesquichloride yields identical equimolar, alternating copolymers in which the pentadiene units have a trans-1,4 configuration (IR, NMR). Although the trans isomer forms cyclic adducts with both maleic anhydride and acrylonitrile, the cis isomer does not undergo the Diels-Alder reaction with these dienophlles. The formation of identical copolymers from cis- and trans-1, 3-pentadiene is attributed to isomerization of the diene-dienophile charge transfer complex in the excited state, resulting in the generation of the same homopolymerizable exciplex from both isomers.     

Polymerization of 1,3-butadiene, 4-methyl-1,3-pentadiene and styrene with catalyst systems based on biscyclopentadienyl derivatives of titanium

1,3-Butadiene, 4-methyl-1,3-pentadiene and styrene were polymerized with dicyclopentadienyltitanium dichloride/methylaluminoxane (Cp₂TiCl₂/MAO) and dicyclopentadienyltitanium chloride/MAO (Cp₂TiCl/MAO). These systems are less active than cyclopentadienyltitanium trichloride/MAO (CpTiCl₃/MAO), but show the same stereospecificity as the latter; they give predominantly cis-1,4-polybutadiene, 1,2-syndiotactic poly(4-methyl-1,3-pentadiene) and syndiotactic polystyrene. Cp₂TiCl/MAO is much more active than Cp₂TiCl₂/MAO; this is probably due to the fact that in the reaction of Cp₂TiCl₂ with MAO, only a small amount of Ti(IV) is reduced to Ti(III), which is the active species in the polymerization of styrene and 1,3-dienes. An interpretation of the structure of the active species in Cp₂TiCl/MAO is reported.     

Isomerization of unsaturated radicals. VI. Isomerization of 3-cyclopenlenyl and pentamethylene radicals

The 184.9 nm photochemistry 0f gaseous 3-methylcyclopentene and 3-methyl-1,4-pentadiene have been studied. Both photoexcited species decompose mainly through the primayy rupture of the C-CH₃ bond. Vibrationally excited 3-cyclopenennyl and pentamethylene radicals are formed in the primayy decomposition in the former and latter systems respectively. These radicals are connected through isomerization reactions: in the presence of DI, the isomers cyclopenten,, and trans-1,3-pentadtene and/or vinylcyclopropane are formed in both systems. The quantum yields depend on the pressure and the starting monomer: cyclopentene and cyclopentadiene are the major products from the photolysis of 3-methylcyclopentene + DI mixtures and only minor quantities of the other C₅H₈ compounds are formed. Cyclopentadiene is the major product of the photolysis of 3-methyl-1,4-pentadiene + O₂ mixtures whereas vinylcyclopropane and trans-1,3-pentadiene are the major C₅ producss of the photolysis of 3-methyl-1,4-pentadiene + DI mixtures. The geometries of 3-cyclopentenyl and of the structures at the six critical points in the torsional potential energy curve (TPEC) for rotation about the 2- and 3-C-C bonds in the open chain pentamethylene species have been optimized completely by ab initio RHF-SCF gradient methods. For the open-chain structures the bond orders, bond lengths and the free valence (primarily associated with the central carbon atom) all correspond to 1,4-pentadien-3-yl conformations. In the ground state there is a high barrier to formation of 3-cyclopentenyl from 1,4-pentadien-3-yl. The features (relative energies and torsionll barriers) of the TPEC for 1,4-pentadien-3-yl explain the ESR observations for the open chain C₅H₇ radical rotamers.     

Copolymerization of propylene with 1,3‐butadiene using isospecific zirconocene catalysts

Poly(propylene‐ran‐1,3‐butadiene) was synthesized using isospecific zirconocene catalysts and converted to telechelic isotactic polypropylene by metathesis degradation with ethylene. The copolymers obtained with isospecific C₂‐symmetric zirconocene catalysts activated with modified methylaluminoxane (MMAO) had 1,4‐inserted butadiene units ( 1,4‐BD ) and 1,2‐inserted units ( 1,2‐BD ) in the isotactic polypropylene chain. The selectivity of butadiene towards 1,4‐BD incorporation was high up to 95% using rac‐dimethylsilylbis(1‐indenyl)zirconium dichloride (Cat‐A)/MMAO. The molar ratio of propylene to butadiene in the feed regulated the number‐average molecular weight (M_n) and the butadiene contents of the polymer produced. Metathesis degradations of the copolymer with ethylene were conducted with a WCI₆/SnMe₄/propyl acetate catalyst system. The ¹H NMR spectra before and after the degradation indicated that the polymers degraded by ethylene had vinyl groups at both chain ends in high selectivity. The analysis of the chain scission products clarified the chain end structures of the poly(propylene‐ran‐1,3‐butadiene). © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5731–5740, 2007     

Tetracyanoethylene pi-complex chemistry. Indirect spectrophotometric determination of Diels-Alder-active 1,3-dienes

An indirect spectrophotometric method, based on the rapid Diels-Alder reaction between cisoid 1,3-dienes and tetracyanoethylene (TCNE) and the destruction of an aromatic-TCNE pi-complex, was developed to determine eleven 1,3-dienes in the 0.05-1.00 x 10(-3)M range. These dienes were: cyclopentadiene; 1,3-cyclohexadiene; trans-1,3-pentadiene; 2,4-dimethyl-1,3-pentadiene; trans-2-methyl-1,3-pentadiene; 2-methyl-1,3-butadiene; 9-methylanthracene; 9,10-dimethylanthracene; 1,6-diphenyl-1,3,5-hexatriene; 2,3-dimethyl-1,3-butadiene; and 1,4-diphenyl-1,3-butadiene. Three 1,3-dienes were determined in the 0.05-1 x 10(-4)M range: cyclopentadiene, trans-2-methyl-1,3-pentadiene, and anthracene. The limit of detection for cyclopentadiene in carbon tetrachloride solutions is 0.11 microg/ml. Fourteen 1,3-dienes were found to form stable pi-complexes and could not be determined by the proposed method. For these 1,3-dienes, the spectra of some of the complexes are reported; in addition, relative equilibrium constants for the pi-complexes of 2,5-dimethyl-2,4-hexadiene, cis-1,3-pentadiene, 4-methyl-1,3-pentadiene, and 1,3-cyclo-octadiene were estimated. An explanation of the transient colour in the 1,3-diene-TCNE Diels-Alder reaction is suggested.     

Studies on polymers from cyclic dienes. XII. Cationic polymerization of spiro[2,4]hepta-4,6-diene

Polymerizations of spiro[2,4]hepta-4,6-diene were carried out with cationic initiators and Ziegler-type catalysts. This monomer polymerized very rapidly with a variety of cationic initiators, and low monomer and initiator concentrations had to be employed in order to avoid formation of crosslinked polymers. The polymer contained 1,2 and 1,4 addition units, and there was no indication of the opening of the cyclopropyl ring in the monomer unit. The following relationship was obtained: [η] = 4.5 × 10^?8M?_n^1.71. The exponential coefficient of this equation is much greater than those typical of vinyl polymers, suggesting that the polymer chain is very stiff. The polymer showed much enhanced resistance to autoxidation as compared with polycyclopentadiene, and its softening point was above 200°C. These interesting physical and chemical properties of the monomer and the polymer can be associated with their spiro structures.     

Isomer distinction by ion/molecule reactions in an ion trap: The case of C5H8

Isomeric C₅H₈ compounds are distinguished by monitoring the products of their reactions with mass-selected ions generated from the individual isomers. This procedure, done by selecting appropriate reaction times in a quadrupole ion trap, yields data for the compounds which are more structure-selective than those obtained by collision-induced dissociation or dissociative charge stripping, both procedures in which isomer distinction is based on the behavior of the molecular ions rather than the neutral molecules themselves. All isomers except cis and trans 1,3-pentadiene can be distinguished by their ion/molecule reactions. The conjugated dienes, 1,3-pentadiene and isoprene, form the deprotonated C₁₀H₁₅⁺ dimer which is not generated by 1,4-pentadiene, cyclopentene, or by the allenes, 2,3-pentadiene and 3-methyl-1,2-butadiene. This clear, qualitative difference enables the isomers 1,4- and 1,3-pentadiene to be distinguished, which is otherwise difficult.     

Regiospecificity of 1-butene polymerization catalyzed by C2-symmetric group IV metallocenes

The regiospecificity of isotactic 1-butene polymerization promoted by typical C₂-symmetric group IV metallocene catalysts was studied by means of ¹³C NMR spectroscopy. In particular, the formation of 1,4 monomer enchainments is discussed.     

Polymerization of (E)‐1,3‐Pentadiene and (E)‐2‐methyl‐1,3‐pentadiene with neodymium catalysts: Examination of the factors that affect the stereoselectivity

(E)‐1,3‐Pentadiene (EP) and (E)‐2‐methyl‐1,3‐pentadiene (2MP) were polymerized to cis‐1,4 polymers with homogeneous and heterogeneous neodymium catalysts to examine the influence of the physical state of the catalyst on the polymerization stereoselectivity. Data on the polymerization of (E)‐1,3‐hexadiene (EH) are also reported. EP and EH gave cis‐1,4 isotactic polymers both with the homogeneous and with the heterogeneous system, whereas 2MP gave an isotactic cis‐1,4 polymer with the heterogeneous catalyst and a syndiotactic cis‐1,4 polymer, never reported earlier, with the homogeneous one. For comparison, the results obtained with the soluble CpTiCl₃‐based catalyst (Cp = cyclopentadienyl), which gives cis‐1,4 isotactic poly(2MP), are examined. A tentative interpretation is given for the mechanism of the formation of the stereoregular polymers obtained and a complete NMR characterization of the cis‐1,4‐syndiotactic poly(2MP) is reported. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3227–3232     

Synthesis and characterization of polymers of 1,4-hexadienes

The homopolymerization of trans-1,4-hexadiene, cis-1,4-hexadiene, and 5-methyl-1,4-hexadiene was investigated with a variety of catalysts. During polymerization, 1,4-hexadienes undergo concurrent isomerization reactions. The nature and extent of isomerization products are influenced by the monomer structure and polymerization conditions. Nuclear magnetic resonance (NMR) and infrared (IR) data show that poly(trans-1,4-hexadiene) and poly(cis-1,4-hexadiene) prepared with a Et₃Al/α-TiCl₃/hexamethylphosphoric triamide catalyst system consist mainly of 1,2-polymerization units arranged in a regular head-to-tail sequence. A 300-MHz proton NMR spectrum shows that the trans-hexadiene polymer is isotactic; it also may be the case for the cis-hexadiene polymer. These polymers are the first examples of uncrosslinked ozone-resistant rubbers containing pendant unsaturation on alternating carbon atoms of the saturated carbon-carbon backbone. Polymerization of the 1,4-hexadienes was also studied with VOCl₃- and β-TiCl₃-based catalysts. Microstructures of the resulting polymers are quite complicated due to significant loss of unsaturation, in contrast to those obtained with the α-TiCl₃-based catalyst. In agreement with the literature, there was no discernible monomer isomerization with the VOCl₃ catalyst system.     

Microstructure determination of poly-(1,3-pentadiene) by a combination of infrared, 60-MHz NMR, 300-MHz NMR,and X-ray diffraction spectroscopy

A quantitative procedure has been developed for characterizing the complete microstructure of polymers of 1,3-pentadiene, including the tacticity of any crystalline component. This can be accomplished by a combination of infrared spectroscopy, X-ray crystallinity, and 300-MHz NMR spectroscopy. A series of high structural purity polymers were synthesized with a series of previously unreported mixed microstructures. These samples were characterized by using the three techniques mentioned, including the previously unreported 300-MHz NMR data. With those results a 60-MHz NMR/IR method of spectroscopy was developed to determine the composition of poly(1,3-pentadiene)s in terms of percent cis-1,2-, cis-1,4-, trans-1,4-, and 3,4-pentadiene units.     

Selective carbometallation of α,β-unsaturated carbonyl compounds and substituted oxacyclopropanes with zirconium-diene complexes

The reactions of zirconium-dience complexes, ZrCp₂(s-cis-diene), with bifunctional electrophiles, i.e. α,β-unsaturated ketones, unsaturated esters and substituted oxacyclopropanes, were investigated. Reaction of ZrCp₂(s-cis-isoprene) with an equivalent of 3-buten-2-one or alkyl acrylates, selectively gives 1,2-addition products. CC bond formation occured at the C(1) atom of the isoprene moiety whereas 1,3-pentadiene-, 2-methyl-1,3-pentadiene- and 2,4-dimethyl-1,3-pentadiene complexes induced the regioselective 1,2-addition at the C(4) position of the diene moiety. Phenyloxacyclopropane and 2-methyl-3-phenyl-oxacyclopropane also react with ZrCp₂(isoprene) leading to CC bond formation from the C(1) atom of isoprene to the oxirane carbon bearing the phenyl group. The corresponding reactions of 2-methyl-2-butene-1,4-diylmagnesium with α,β-unsaturated carbonyl compounds were also studied and found to give quite different products.