Reactive poly(glycidyl methacrylate) microspheres prepared by dispersion polymerization

Poly(glycidyl methacrylate) [poly(GMA)] microspheres of narrow size distribution were prepared in a simple one‐step procedure by dispersion radical polymerization. Depending on the solvent used, poly(GMA) particle size could be controlled in the range of 0.5–4 μm by changing the solubility parameter of the reaction mixture. In N,N′‐dimethylformamide (DMF)/methanol mixture, the particle size increased and the size distribution broadened with decreasing initial solubility parameter. While in the DMF/methanol solvent system, hydroxypropyl cellulose (HPC) or cellulose acetate butyrate (CAB) were taken as steric stabilizers of the dispersion polymerization, poly(vinylpyrrolidone) (PVP) was used in alcoholic media. Contrary to the DMF/methanol system, narrow particle size distributions were obtained with PVP‐stabilized polymerizations in ethanolic, methanolic, propan‐1‐olic or butan‐1‐olic medium. Both the particle size and polydispersity were reduced with increasing stabilizer concentration. If lower molecular‐weight PVP was used, larger microspheres were obtained. Poly(GMA) samples prepared in a neat alcoholic medium virtually quantitatively retained oxirane group content after the polymerization. Reactivity of the poly(GMA) microspheres was confirmed by their hydrolysis and aminolysis. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3855–3863, 2000     

Synthesis of poly(vinyl acetate-methyl methacrylate) copolymer microspheres using suspension polymerization

Poly(vinyl acetate-methyl methacrylate) (VAc-MMA) copolymer microspheres were prepared using suspension polymerization at low temperature initiated with 2,2'-azobis(2,4-dimethyl valeronitrile) (ADMVN). The poly(VAc-MMA) copolymer microspheres can be used over a large area where homopolymers, polyvinyl acetate (PVAc) and methyl methacrylate (PMMA) microspheres are capable of being put to use. The prepared microspheres were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), differential scanning calorimetry (DSC) and thermal gravimetric analysis (TGA). Obtained copolymer microspheres which have 200 μm average diameter and higher thermal stability than those of homopolymer.     

Thermal behaviour of poly(allyl azide)

The paper describes the synthesis of low molecular mass poly(allyl chloride) (PAC) (M _n= 856-3834 g mol^-1) using Lewis acid (ALCL₃, FeCL₃, TiCL₄) and al powder. Branching in PAC was indicated on the basis of elemental analysis and ¹H-NMR spectroscopy. azidation of pac could be carried out at 100°C by using NaN₃ and DMSO as solvent. Curing of poly(allyl azide) (PAA) by cyclic dipolar addition reaction with EGDMA (ethylene glycol dimethacrylate, 5-45 phr) was investigated by differential scanning calorimetry and structure of cured polymer was confirmed by FTIR. A two-step mass loss was exhibited by uncured and cured PAA in nitrogen atmosphere. A mass loss of 20-28% (155-274°C) and 50-61% (330-550°C) was observed. This revised version was published online in July 2006 with corrections to the Cover Date.     

Ce(IV)-induced polymerization of allyl methacrylate with cotton cellulose

Ce(IV)-induced polymerization of allyl methacrylate (AMA) with cotton cellulose was investigated under a variety of conditions. Polymer add-on was directly related to AMA concentration. The same holds good for Ce(IV) ion concentration up to a certain concentration (30 mmol/L), after which it decreases. Polymer add-on was higher at 60 than at 50 and 70°C. A methanol/water mixture (20/80) offers the best medium for polymerization. Addition of nitric acid (up to 400 mol equivalent/L) or perchloric acid (up to 800 mol equivalent/L) to the polymerization system caused significant enhancement in polymer add-on. The reverse was the case with sulphuric acid irrespective of the concentration used. A comparison between polymer add-on values based on increase in weight and those based on estimated allyl double bonds indicated that the latter undergo partial homopolymerization.     

Monodisperse poly(chloromethylstyrene-co-divinylbenzene) microspheres by precipitation polymerization

Monodisperse poly(chloromethylstyrene-co-divinylbenzene-80) microspheres of 4–6-µm diameter were prepared by precipitation copolymerization in neat acetonitrile and in acetonitrile/toluene mixtures. These particles have clean surfaces due to the absence of any added stabilizer and up to 0.5 cm³/g pore volume, depending on the comonomer ratio and on the amount of toluene cosolvent. The effects of comonomer and cosolvent ratios on microsphere formation and morphology are described. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2295–2303, 1999     

Magnetic poly(glycidyl methacrylate) microspheres prepared by dispersion polymerization in the presence of electrostatically stabilized ferrofluids

Fine magnetite nanoparticles, both electrostatically stabilized and nonstabilized, were synthesized in situ by precipitation of Fe(II) and Fe(III) salts in alkaline medium. Magnetic poly(glycidyl methacrylate) (PGMA) microspheres with core‐shell structure, where Fe₃O₄ is the magnetic core and PGMA is the shell, were obtained by dispersion polymerization initiated with 2,2′‐azobisisobutyronitrile (AIBN), 4,4′‐azobis(4‐cyanovaleric acid) (ACVA), or ammonium persulfate (APS) in ethanol containing poly(vinylpyrrolidone) or ethylcellulose stabilizer in the presence of iron oxide ferrofluid. The average microsphere size ranged from 100 nm to 2 μm. The effects of the nature of ferrofluid, polymerization temperature, monomer, initiator, and stabilizer concentration on the PGMA particle size and polydispersity were studied. The particles contained 2–24 wt % of iron. AIBN produced larger microspheres than APS or ACVA. Polymers encapsulating electrostatically stabilized iron oxide particles contained lower amounts of oxirane groups compared with those obtained with untreated ferrofluid. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5827–5837, 2004     

Porous monodisperse poly(divinylbenzene) microspheres by precipitation polymerization

The precipitation polymerization of commercial divinylbenzene in acetonitrile containing up to 40 vol. % toluene or other cosolvents is shown to produce novel porous monodisperse poly(divinylbenzene) microspheres. These microspheres have diameters between 4 and 7 μm, total pore volumes of up to 0.52 cm³/g, and surface areas of up to 800 m²/g. As no surfactant nor stabilizer was used in the preparation of these particles, their surfaces are free of any such residues. The particles were slurry-packed into stainless steel columns for size exclusion chromatography evaluation, and the results show an exclusion limit at molecular weights of 500 g/mol. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1543–1551, 1998     

Bulk atom transfer radical polymerization of allyl methacrylate

A detailed investigation of the polymerization of allyl methacrylate, a typical unsymmetrical divinyl compound containing two types of vinyl groups, methacryloyl and allyl, with quite different reactivities, was performed with atom transfer radical polymerization (ATRP). Homopolymerizations were carried out in bulk, with ethyl‐2‐bromoisobutyrate as the initiator and with copper halide (CuX, where X is Cl or Br) with N,N,N′,N″,N″‐pentamethyldiethylenetriamine as the catalyst system. Kinetic studies demonstrated that during the early stages of the polymerization, the ATRP process proceeded in a living manner with a low and constant radical concentration. However, as the reaction continued, the increased diffusion resistance restricted the mobility of the catalyst system and interrupted the equilibrium between the growing radicals and dormant species. The obtained poly(allyl methacrylate)s (PAMAs) were characterized with Fourier transform infrared, ¹H NMR, and size exclusion chromatography techniques. The dependence of both the gel point conversion and molecular characteristics of the PAMA prepolymers on different experimental parameters, such as the initiator concentration, polymerization temperature, and type of halide used as the catalyst, was analyzed. These real gel points were compared with the ones calculated according to Gordon's equation under the tentative assumption of equal reactivity for the two types of vinyl groups. Moreover, the microstructure of the prepolymers was the same as that exhibited by those homopolymers prepared by conventional free‐radical polymerization; the fraction of syndiotactic arrangements increased as the reaction temperature was lowered. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2395–2406, 2005     

Preparation and surface modification of magnetic poly(methyl methacrylate) microspheres

~~Preparation and surface modification of magnetic poly(methyl methacrylate) microspheres~~     

Synthesis of poly(sorbitan methacrylate) hydrogel by free-radical polymerization

Hydrogels are materials with the ability to swell in water through the retention of significant fractions of water within their structures. Owing to their relatively high degree of biocompatibility, hydrogels have been utilized in a host of biomedical applications. In an attempt to determine the optimum conditions for hydrogel synthesis by the free-radical polymerization of sorbitan methacrylate (SMA), the hydrogel used in this study was well polymerized under the following conditions: 50% (w/v) SMA as monomer, 1% (w/w) alpha, alpha'-azo-bis(isobutyro-nitrile) as thermal initiator, and 1% (w/w) ethylene glycol dimethacrylate as cross-liking agent. Under these conditions, the moisture content of the polymerized SMA hydrogel was higher than in the other conditions. Moreover, the moisture content of the poly(SMA) hydrogel was also found to be higher than that of the poly(methyl methacrylate [MMA]) hydrogel. When the Fourier transform-infrared spectrum of poly(SMA) hydrogel was compared with that of poly(MMA) hydrogel, we noted a band at 1735-1730/cm, which did not appear in the Fourier transform-infrared spectrum of poly(MMA). The surface of the poly(SMA) hydrogel was visualized through scanning electron microscopy, and was uniform and clear in appearance.     

Synthesis of high molecular weight poly(methyl methacrylate) microspheres by suspension polymerization in the presence of silver nanoparticles

To prepare high molecular weight (HMW) poly(methyl methacrylate) (PMMA)/silver microspheres, methyl methacrylate was suspension-polymerized in the presence of silver nanoparticles using a low-temperature initiator at different conditions. The rate of conversion was increased with increasing initiator concentration. In the case of adding silver nanoparticles, the rate of polymerization decreased slightly. High monomer conversion (about 95%) was obtained in spite of low polymerization temperature of 30 °C. Under controlled conditions, PMMA/silver microspheres with various viscosity-average degree of polymerization (6,000–37,000) were prepared.     

Radical polymerization of methyl methacrylate in the presence of isotactic poly(methyl methacrylate)

Methyl methacrylate (MMA) was polymerized by radical initiation at 25°C in DMF in the presence of preformed isotactic PMMA (iMA) with about 90% isotactic triads and different M?_v's, viz., iMA-1: 7.2 × 10⁵; iMA-2, 5.0 × 10⁵; iMA-3, 3.5 × 10⁵; iMA-4, 1.25 × 10⁵; and iMA-5, 1.15 × 10⁵. The MMA:iMA ratio was 6:1. The collected polymers were separated into two fractions by extraction with boiling acetone and characterized by 60 MHz NMR. It is found that the M?_v of the polymer formed ran parallel to the M?_v of iMA. In all cases syndiotactic PMMA (s-PMMA) was produced which associated with the isotactic substrate to form acetone-insoluble stereocomplexes. The syndiotactic polymers probably consist of long syndiotactic and heterotactic sequences. The syndiotacticity decreased with conversion and was generally highest in the presence of iMA-1. With iMA-1 even the formation of some additional i-PMMA (in the acetone-insolubles) was indicated, especially in the later stages of the polymerization. Characterization of the acetone-soluble fractions indicated that i,s-stereoblock polymers were also produced, of which the persistence ratios ρ increased with the M?_v of iMA. From these results it is concluded that this reaction differs from the conventional radical polymerization and can be considered a stereospecific replica polymerization, the driving force being the strong tendency of i- and s-PMMA to associate. The formation of i,s-stereoblock polymers and additional i-PMMA indicates that s-PMMA in its turn can also act as a polymer matrix.     

Radical polymerization of methyl methacrylate in the presence of low-molecular-weight poly(methyl methacrylate)

The kinetics of the bulk radical polymerization of methyl methacrylate and the structure and properties (physicomechanical and thermomechanical, as well as diffusion and sorption) of the polymers were examined in relation to the amount of low-molecular-weight poly(methyl methacrylate) added.     

End-functional poly(methyl methacrylate)s via group transfer polymerization

Hydroxyl-, amine-, and lactone-end-functional poly(methyl methacrylate)s (PMMA) were prepared with controlled molecular weights and M_w/M_n = 1.06–1.19 via group transfer polymerization. This was achieved by the electrophilic termination of silyl ketene acetal ended PMMAs with benzaldehyde, N-trimethylsilyl benzaldimine, and 5,6-dihydro-2H-pyran-2-one, respectively. The number-average degree of functionalization, as determined by NMR/SEC, was in the range of 0.70–0.85. A Lewis acid was used for terminating silyl ketene acetal ended PMMA with N-trimethylsilyl benzaldimine, whereas tetra-n-butyl ammonium bibenzoate was used in the case of benzaldehyde and 5,6-dihydro-2H-pyran-2-one. MALDI-TOF MS analysis of the end-functional polymers indicated the competing formation of cyclic end groups due to a back-biting reaction along with end-functional PMMAs. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2514–2531, 2007     

Gelation in free-radical terpolymerization of poly(allyl methacrylate) crosslinked polymer nanosphere with allyl benzoate and vinyl benzoate

Microgel-like poly(allyl methacrylate) (PAMA nanosphere) was prepared by the emulsion polymerization of AMA as the reactive crosslinked polymer nanosphere with abundant pendant allyl groups. The terpolymerization of PAMA nanosphere with allyl benzoate (ABz) and vinyl benzoate (VBz) was conducted in bulk using benzoyl peroxide as initiator at 80 °C. The gelation depended on the feed ABz/VBz molar ratio since the molecular weights of resulting poly(ABz-co-VBz)s that act as the bridges increased with an increase in the mole fraction of VBz in the feed monomer. Beyond the gel point, the sol was rapidly incorporated into the gel and the increasing tendency of the gel fraction became steeper from 70 to 95 mol% of VBz as a reflection of increased chain length of bridge between PAMA nanospheres. Moreover, the swelling ratio became lower with increasing the mole percentage of VBz in the feed monomer. These results would support the preferential incorporation of PAMA nanosphere into the gel and the longer bridge can capture more nanospheres to give a much shrunken gel.     

XPS analysis (ESCA) of the surface composition of poly(styrene/2-hydroxyethyl methacrylate) microspheres produced by emulsifier-free emulsion polymerization

Polymer microspheres composed of various compositions of styrene and 2-hydroxyethyl methacrylate (HEMA) were produced by batch emulsifier-free emulsion polymerization. The HEMA content at the surface, [HEMA] _s , of the microspheres powdered by freeze-drying was determined by both quantitativeC ^1s /O ^1s analysis andC ^1s peak shape analysis of the x-ray photoelectron spectroscopic spectra. When the HEMA content in the microsphere, [HEMA] _p , was less than about 5 mole%, the [HEMA] _s values determined by the two different methods showed good agreement. At [HEMA]_p above 5 mole %, [HEMA]_s values determined by the first method were about 15 mole % greater than those determined by the second. They both showed a similar tendency with the [HEMA] _s being higher than the [HEMA] _p , e.g., when [HEMA] _p was 1 mole %, [HEMA] _s was 11 mole %. The intensity of the satellite peak due to the ^* transition of the benzene ring of the styrene component decreased with an increase in [HEMA] _p , to zero at 5 mole % of [HEMA] _p . These results indicate that the HEMA component is localized at the surface.Part CVIII of the series Studies on Suspension and Emulsion.     

Solvent dependent photophysical behaviour of poly(1-naphthyl methacrylate)

The emission spectra and photophysical behaviour of poly(1-naphthyl methacrylate) singlet state were investigated in solvents of different thermodynamic character. The quantum yields of monomeric emission, the life-times of the isolated unit and the rate constants for the quenching by biacetyl were evaluated. The same measurements were carried out for the monomeric (1-naphthyl acetate) and dimeric (di-1-naphthyl glutarate) model compounds. The data allow discussion of the effects of solvent on excimer formation and intramolecular energy migration.     

Fabrication of poly(methyl methacrylate) microfluidic chips by redox-initiated polymerization

In this report, a method based on the redox-initiated polymerization of methyl methacrylate (MMA) has been developed for the rapid fabrication of poly(methyl methacrylate) (PMMA) microfluidic chips. MMA containing 2-2'-azo-bis-isobutyronitrile was allowed to prepolymerize in a water bath to form a viscous prepolymer solution that was subsequently mixed with MMA containing a redox-initiation couple of benzoyl peroxide/N,N-dimethylaniline. The dense molding solution was sandwiched between a silicon template and a piece of 1-mm-thick PMMA plate. The polymerization could complete within 50 min under ambient temperature. The images of raised microfluidic structures on the silicon template were precisely replicated into the synthesized PMMA substrate during the redox-initiated polymerization of the molding solution. The chips were subsequently assembled by the thermal bonding of the channel plates and the covers. The new fabrication approach obviates the need for special equipment and significantly simplifies the process of fabricating PMMA microdevices. The attractive performance of the novel PMMA microchips has been demonstrated in connection with contactless conductivity detection for the separation and detection of ionic species.