High molar mass ethene/1‐olefin copolymers synthesized with acenaphthyl substituted metallocene catalysts

The influence of ligand structure on copolymerization properties of metallocene catalysts was elucidated with three C₁‐symmetric methylalumoxane (MAO) activated zirconocene dichlorides, ethylene(1‐(7, 9)‐diphenylcyclopenta‐[a]‐acenaphthadienyl‐2‐phenyl‐2‐cyclopentadienyl)ZrCl₂ ( 1 ), ethylene(1‐(7, 9)‐diphenylcyclopenta‐[a]‐acenaphthadienyl‐2‐phenyl‐2‐fluorenyl)ZrCl₂ ( 2 ), and ethylene(1‐(9)‐fluorenyl‐(R)1‐phenyl‐2‐(1‐indenyl)ZrCl2 ( 3 ). Polyethenes produced with 1 /MAO had considerable, ca. 10% amount of trans‐vinylene end groups, resulting from the chain end isomerization prior to the chain termination. When ethene was copolymerized with 1‐hexene or 1‐hexadecene using 1 /MAO, molar mass of the copolymers varied from high to moderate (531–116 kg/mol) depending on the comonomer feed. At 50% comonomer feed, ethene/1‐olefin copolymers with high hexene or hexadecene content (around 10%) were achievable. In the series of catalysts, polyethenes with highest molar mass, up to 985 kg/mol, were obtained with sterically most crowded 2 /MAO, but the catalyst was only moderately active to copolymerize higher olefins. Catalyst 3 /MAO produced polyethenes with extremely small amounts of trans‐vinylene end groups and relatively low molar mass 1‐hexene copolymers (from 157 to 38 kg/mol) with similar comonomer content as 1 . These results indicate that the catalyst structure, which favors chain end isomerization, is also capable to produce high molar mass 1‐olefin copolymers with high comonomer content. In addition, an exceptionally strong synergetic effect of the comonomer on the polymerization activity was observed with catalyst 3 /MAO. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 373–382, 2008     

Unconstrained geometry complexes: Ethylene/α‐olefin copolymerizations with a tetramethyldisilyl‐bridged Cp‐amido titanium complex

A new disilyl‐bridged complex, [(N‐tert‐butylamido)(3‐indenyl)tetramethyldisilyl]titanium dichloride ( 3 ), was synthesized and activated with methylaluminoxane (MAO) for propylene homopolymerization and ethylene/propylene and ethylene/1‐hexene copolymerizations. A polypropylene with a slight isotactic enrichment was obtained. The number of regioerrors present in the polypropylene was somewhat smaller than that found in most polypropylenes made from monosilyl‐bridged [(N‐tert‐butylamido)(3‐indenyl)dimethylsilyl]titanium dichloride. The regioerrors detected in the copolymers obtained from 3 /MAO were on the order of the amounts observed in polymers made with the monosilyl‐bridged constrained geometry catalysts. Ethylene copolymers of propylene and 1‐hexene had random sequence distributions and showed significant comonomer incorporation. Because of the presence of regioerrors, a modified method for determining the monomer composition and sequence distribution was developed from the direct measurement of the monomer content from the number of methylene and methine carbons per polymer chain, regardless of propylene inversion. An estimate of the error in the copolymerization reactivity ratio determination for regioirregular ethylene/α‐olefin copolymers was obtained by the calculation of the reactivity ratios from monomer dyad sequences, with consideration given to the contribution of major regioirregular sequences. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3840–3851, 2005     

Copolymerization behavior of titanium imidazolin‐2‐iminato complexes

Monocyclopentadienyl titanium imidazolin‐2‐iminato complexes [Cp′Ti(L)X₂] 1a (Cp′ = cyclopentadienyl, L = 1,3‐di‐tert‐butylimidazolin‐2‐imide, X = Cl), 1b (X = CH₃); 2 (Cp′ = cyclopentadienyl, L = 1,3‐diisopropylimidazolin‐2‐imide, X = Cl); 3 (Cp′ = tert‐butylcyclopentadienyl, L = 1,3‐di‐tert‐butylimidazolin‐2‐imide, X = Cl), upon activation with methylaluminoxane (MAO) were active for the polymerization of ethylene and propylene and the copolymerization of ethylene and 1‐hexene. Catalysts derived from imidazolin‐2‐iminato tropidinyl titanium complex 4 = [(Trop)Ti(L)Cl₂] (Trop = tropidinyl, L = 1,3‐di‐tert‐butylimidazolin‐2‐imide) were much less active. Narrow polydispersities were observed for ethylene and propylene polymerization, but the copolymerization of ethylene/hexene led to bimodal molecular weight distributions. The productivity of catalysts derived from the dialkyl complex 1b activated with [Ph₃C][B(C₆F₅)₄] or B(C₆F₅)₃ were less active for ethylene/hexene copolymerization but yielded ethylene/hexene copolymers of narrower molecular weight distributions than those derived from 1a/MAO. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6064–6070, 2008     

Controlled radical polymerization of a trialkylsilyl methacrylate by reversible addition–fragmentation chain transfer polymerization

The reversible addition–fragmentation chain transfer (RAFT) polymerization of a hydrolyzable monomer (tert‐butyldimethylsilyl methacrylate) with cumyl dithiobenzoate and 2‐cyanoprop‐2‐yl dithiobenzoate as chain‐transfer agents was studied in toluene solutions at 70 °C. The resulting homopolymers had low polydispersity (polydispersity index < 1.3) up to 96% monomer conversion with molecular weights at high conversions close to the theoretical prediction. The profiles of the number‐average molecular weight versus the conversion revealed controlled polymerization features with chain‐transfer constants expected between 1.0 and 10. A series of poly(tert‐butyldimethylsilyl methacrylate)s were synthesized over the molecular weight range of 1.0 × 10⁴ to 3.0 × 10⁴, as determined by size exclusion chromatography. As strong differences of hydrodynamic volumes in tetrahydrofuran between poly(methyl methacrylate), polystyrene standards, and poly(tert‐butyldimethylsilyl methacrylate) were observed, true molecular weights were obtained from a light scattering detector equipped in a triple‐detector size exclusion chromatograph. The Mark–Houwink–Sakurada parameters for poly(tert‐butyldimethylsilyl methacrylate) were assessed to obtain directly true molecular weight values from size exclusion chromatography with universal calibration. In addition, a RAFT agent efficiency above 94% was confirmed at high conversions by both light scattering detection and ¹H NMR spectroscopy. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5680–5689, 2005     

Novel substituted epoxide initiators for the carbocationic polymerization of isobutylene

This article presents the first detailed account of the discovery that substituted epoxides can initiate the carbocationic polymerization of isobutylene. α‐Methylstyrene epoxide (MSE), 2,4,4‐trimethyl‐pentyl‐epoxide‐1,2 (TMPO‐1), 2,4,4‐trimethyl‐pentyl‐epoxide‐2,3 (TMPO‐2), and hexaepoxi squalene (HES) initiated isobutylene polymerization in conjunction with TiCl₄. MSE, TMPO‐2, and HES initiated living polymerizations. A competitive reaction mechanism is proposed for the initiation and propagation. According to the proposed mechanism, initiator efficiency is defined by the competition between the S_N1 and S_N2 reaction paths. A controlled initiation with external epoxides such as MSE should yield a primary hydroxyl head group and a tert‐chloride end‐group. The presence of tert‐chloride end‐groups was verified by NMR spectroscopy, whereas the presence of primary hydroxyl groups was implied by model experiments. Multiple initiation by HES was verified by diphenyl ethylene end‐capping and NMR analysis; the resulting star polymer had an average of 5.2 arms per molecule. A detailed investigation of the reaction mechanism and the characterization of the polymers are in progress. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 444–452, 2000     

Polymerization of isoprene with η5‐C5H4(tert‐Bu)TiCl3/MAO catalyst

cis‐Selective polymerizations of isoprene with the catalysts composed of η⁵‐C₅H₄(R)TiCl₃ (1; R?H, 2 ; tert‐Bu) and methylaluminoxane were investigated. Both catalysts showed remarkable catalytic activities for the polymerization of isoprene. The polymerization activities were strongly affected by the substituent introduced on cyclopentadienyl ring. Introduction of bulky tert‐butyl group was found to be effective for enhancement of polymerization activity, but the cis‐content of polyisoprene prepared by the 2 /MAO catalyst was lower than that by 1 /MAO catalyst. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1841–1844, 2004     

Novel cyclohexyl‐substituted salicylaldiminato–nickel(II) complex as a catalyst for ethylene homopolymerization and copolymerization

The cyclohexyl‐substituted salicylaldiminato–Ni(II) complex [O? (3‐C₆H₁₁)(5‐CH₃)C₆H₂CH?N‐2,6‐C₆H₃ⁱPr₂]Ni(PPh₃)(Ph) ( 4 ) has been synthesized and characterized with ¹H NMR and X‐ray structure analysis. In the presence of phosphine scavengers such as bis(1,5‐cyclooctadiene)nickel(0) [Ni(COD)₂], triisobutylaluminum (TIBA), and triethylaluminum (TEA), 4 is an active catalyst for ethylene polymerization and copolymerization with the polar monomers tert‐butyl‐10‐undecenoate, methyl‐10‐undecenoate, and 4‐penten‐1‐ol under mild conditions. The polymerization parameters affecting the catalytic activity and viscosity‐average molecular weight of polyethylene, such as the temperature, time, ethylene pressure, and catalyst concentration, are discussed. A polymerization activity of 3.62 × 10⁵ g of PE (mol of Ni h)^?1 and a weight‐average molecular weight of polyethylene of 5.73 × 10⁴ g^.mol^?1 have been found for 10 μmol of 4 and a Ni(COD)₂/ 4 ratio of 3 in a 30‐mL toluene solution at 45 °C and 12 × 10⁵ Pa of ethylene for 20 min. The polydispersity index of the resulting polyethylene is about 2.04. After the addition of tetrahydrofuran and Et₂O to the reaction system, 4 exhibits still high activity for ethylene polymerization. Methyl‐10‐undecenoate (0.65 mol %), 0.74 mol % tert‐butyl‐10‐undecenoate, and 0.98 mol % 4‐penten‐1‐ol have been incorporated into the polymer. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 6071–6080, 2004     

Long‐chain‐branched polyethene by the copolymerization of ethene and nonconjugated α,ω‐dienes

Ethene was copolymerized (1) with 1,5‐hexadiene with rac‐ethylenebis(indenyl)zirconium dichloride/methylaluminoxane (MAO) used as a catalyst and (2) with 1,7‐octadiene with bis(n‐butylcyclopentadienyl)zirconium dichloride/MAO and rac‐ethylenebis(indenyl)hafnium dichloride (Et[Ind]₂HfCl₂)/MAO used as catalysts at 80 °C in toluene. The copolymer microstructure and the influence of diene incorporation on the rheological properties were examined. Ethene and 1,5‐hexadiene formed a copolymer in which a major fraction of the 1,5‐hexadiene was incorporated into rings and a small fraction formed 1‐butenyl branches. The copolymerization of ethene with 1,7‐octadiene resulted in a higher selectivity toward branch formation. Some of the branches formed long‐chain‐branching (LCB) structures. The ring formation selectivity increased with decreasing ethene concentration in the polymerization reactor. Melt rheological properties of the diene copolymers resembled those of metallocene‐catalyzed LCB homopolyethenes and depended on the vinyl content, the catalyst, and the polymerization conditions. At high diene contents, all three catalysts produced crosslinked polyethene. This was especially pronounced with Et[Ind]₂HfCl₂, where only 0.2 mol % 1,7‐octadiene in the copolymer was required to achieve significantly modified rheological properties. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3805–3817, 2001     

Hyperbranched aryl polycarbonates derived from A2B monomers versus AB2 monomers

Hyperbranched aryl polycarbonates were prepared via the polymerizations of A₂B and AB₂ monomers, which involved the condensation of chloroformate (A) functionalities with tert‐butyldimethylsilyl‐protected phenols (B), facilitated by reactions with silver fluoride. The polymerization of the A₂B monomer gave hyperbranched polycarbonates bearing fluoroformate chain ends, which were hydrolyzed to phenolic chain‐end moieties and further elaborated to tert‐butyldimethylsilyl ether groups. The polymerization of the AB₂ monomer gave tert‐butyldimethylsilyl ether‐terminated hyperbranched polycarbonates. The polymerizations were conducted at 23–70 °C in 20% acetonitrile/tetrahydrofuran in the presence of a stoichiometric excess of silver fluoride for 20–40 h to afford hyperbranched polycarbonates with weight‐average molecular weights exceeding 100,000 Da and polydispersity indices of typically 2–3. The degrees of branching were determined by a reductive degradation procedure followed by high‐performance liquid chromatography. Alternatively, the degrees of branching were measurable by solution‐state ¹H NMR analyses and agreed with the statistical 50% branching expected for the polymerization of A₂B and AB₂ monomers not experiencing constructive or destructive electronic effects on the reactivity of the multiple functional groups. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 823–835, 2002; DOI 10.1002/pola.10167     

Stereoselective Synthesis and Reactions of Secondary Alkyllithium Reagents Functionalized at the 3‐Position

Secondary alkyllithium reagents bearing an OTBS group (TBS=tert‐butyldimethylsilyl) at the 3‐position can be prepared stereoconvergently through an I/Li exchange from a diastereomeric mixture of the corresponding secondary alkyl iodides. These lithium reagents react with a range of electrophiles, including carbon electrophiles, with retention of configuration to yield various 1,3‐difunctionalized derivatives with good diastereoselectivities. Kinetic studies show that the 3‐siloxy group strongly accelerates the epimerization at the lithium‐substituted carbon atom. This method offers a new way to construct chiral open‐chain molecules with excellent stereoselectivity.     

Silyl‐protected hydroxystyrenes: Living anionic polymerization at room temperature and selective desilylation

Both 4‐ and 3‐(tert‐butyldimethylsilyl)oxystyrene (MSOST) undergo living anionic polymerization at room temperature with sec‐butyllithium (sBuLi) in cyclohexane or methylcyclohexane upon injection of a small amount of tetrahydrofuran. Desilylation can be conveniently afforded with hydrogen chloride or tetra(alkyl)ammonium fluoride to provide poly(hydroxystyrene) (PHOST) with a narrow molecular weight distribution, which could be further transformed to other polystyrene derivatives. ¹³C NMR spectra of poly(tert‐butyldimethylsilyloxystyrene) (PMSOST) and PHOST prepared under different conditions (tetrahydrofuran vs. cyclohexane, −78 °C vs. 20 °C) have indicated that the room temperature living polymerization in the hydrocarbon‐rich solvent produces polymers with high syndiotacticity. Similarly, 4‐(tert‐butyldiphenylsilyl)oxystyrene (PhSOST), a new monomer, provides living anionic polymerization at room temperature. Desilylation of this polymer can be achieved using tetra(n‐butyl)ammonium or tetraethylammonium fluoride. Inertness of the phenylsilyl ether to HCl allows selective desilylation of the dimethylsilyl ether with HCl in the presence of the phenylsilyl ether group, providing a new route to interesting macromolecules. Application of the selective desilylation technique to the synthesis of a block copolymer of HOST and 4‐tert‐butoxycarbonyloxystyrene (BOCST) is described. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2415–2427, 2000     

Composition distribution of ethylene or propylene–norbornene copolymers obtained with zirconocene catalysts

Copolymerization of ethylene or propylene and norbornene (NB) was carried out with stereospecific zirconocene catalysts rac‐ethylenebis(indenyl)zirconium dichloride, rac‐dimethylsilylenebis(indenyl)zirconium dichloride ( 2 ), rac‐dimethylsilylenebis(2‐methylindenyl)zirconium dichloride, and diphenylmethylene(cyclopentadienyl)(9‐fluorenyl)zirconium dichloride combined with cocatalysts at 40 °C. Temperature‐rising elution fractionation of the copolymers was carried out with cross‐fractionation chromatography with o‐dichlorobenzene as a solvent, and a broad distribution of the copolymer composition was detected. The fraction eluted at lower temperature contained higher NB. The effect of the polymerization time was examined in the ethylene–NB copolymerization with catalyst 2 , and the higher‐temperature elution fraction increased with increasing polymerization time. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 441–448, 2003     

Reactivity of styrene and substituted styrenes in the presence of a homogeneous isospecific titanium catalyst

The isospecific polymerization of several para‐substituted styrenes was performed in the presence of the catalyst dichloro[1,4‐dithiabutanediyl‐2,2′‐bis(4,6‐di‐tert‐butyl‐phenoxy)]titanium activated by methylaluminoxane. All the polymers were highly regioregular and isotactic with narrow molecular weight distributions. The presence of electron‐donating substituents on the aromatic ring had a positive effect on the catalyst activity, whereas electron‐withdrawing substituents affected the polymerization activity negatively. Binary copolymerizations of the various substituted styrenes showed an inversion of the reactivity with respect to that observed in the homopolymerization. These results suggested that the last monomer unit of the polymer chain coordinated to the metal center, influencing the reactivity of the catalyst with respect to the incoming monomer. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1486–1491, 2006     

Effect of an alkyl substituted in salen ligands on 1,4‐Cis selectivity and molecular weight control in the polymerization of 1,3‐butadiene with (salen)Co(II) complexes in combination with methylaluminoxane

The effect of an alkyl substituted in the aromatic ring of the salen ligand on the polymerization of butadiene (Bd) with (salen)Co(II) complexes in combination with methylaluminoxane (MAO) was investigated. The activity for the polymerization of Bd was influenced significantly by the introduction of alkyl groups at the 3,3′,5,5′‐positions in the aromatic ring of the salen ligand, and both the polymerization rate and 1,4‐cis contents increased in the following order with respect to the alkyl group: H < CH₃ < t‐C₄H₉. This is in good agreement with the bulkiness of the alkyl groups. The activity for the polymerization of the (salen)Co(II) complex possessing t‐C₄H₉ at the 3,3′‐positions was higher than that of the (salen)Co(II) bearing t‐C₄H₉ at the 5,5′‐positions. Thus, the introduction of bulky substituents at the 3,3′‐positions of the salen ligand was an important factor in achieving both high activity and high 1,4‐cis selectivity in the polymerization of Bd with (salen)Co(II) complexes in combination with MAO. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4088–4094, 2006     

Synthesis and self‐assembly of well‐defined cyclodextrin‐centered amphiphilic A14B7 multimiktoarm star copolymers based on poly(ε‐caprolactone) and poly(acrylic acid)

Novel amphiphilic A₁₄B₇ multimiktoarm star copolymers composed of 14 poly(ε‐caprolactone) (PCL) arms and 7 poly(acrylic acid) (PAA) arms with β‐cyclodextrin (β‐CD) as core moiety were synthesized by the combination of controlled ring‐opening polymerization (CROP) and atom transfer radical polymerization (ATRP). 14‐Arm star PCL homopolymers (CDSi‐SPCL) were first synthesized by the CROP of CL using per‐6‐(tert‐butyldimethylsilyl)‐β‐CD as the multifunctional initiator in the presence of Sn(Oct)₂ at 125 °C. Subsequently, the hydroxyl end groups of CDSi‐SPCL were blocked by acetyl chloride. After desilylation of the tert‐butyldimethylsilyl ether groups from the β‐CD core, 7 ATRP initiating sites were introduced by treating with 2‐bromoisobutyryl bromide, which further initiated ATRP of tert‐butyl acrylate (tBA) to prepare well‐defined A₁₄B₇ multimiktoarm star copolymers [CDS(PCL‐PtBA)]. Their molecular structures and physical properties were in detail characterized by ¹H NMR, SEC‐MALLS, and DSC. The selective hydrolysis of tert‐butyl ester groups of the PtBA block gave the amphiphilic A₁₄B₇ multimiktoarm star copolymers [CDS(PCL‐PAA)]. These amphiphilic copolymers could self‐assemble into multimorphological aggregates in aqueous solution, which were characterized by dynamic light scattering (DLS), transmission electron microscopy (TEM) and atomic force microscopy (AFM). © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2961–2974, 2010     

N‐(2‐benzimidazolylquinolin‐8‐yl)benzamidate half‐titanocene chlorides: Synthesis,characterization and their catalytic behavior toward ethylene polymerization

A series of N‐(2‐benzimidazolyquinolin‐8‐yl)benzamidate half‐titanocene chlorides, Cp′TiLCl ( C1 – C8 : Cp′ = C₅H₅, MeC₅H₄, or C₅Me₅; L = N‐(benzimidazolyquinolin‐8‐yl)benzamides)), was synthesized by the KCl elimination reaction of half‐titanocene trichlorides with the correspondent potassium N‐(2‐benzimidazolyquinolin‐8‐yl)benzamide. These half‐titanocene complexes were fully characterized by elemental and NMR analyses, and the molecular structures of complexes C2 and C8 were determined by the single‐crystal X‐ray diffraction. The high stability of the pentamethylcyclopentadienyl complex ( C8 ) was evident by no decomposing nature of its solution in air for one week. The oxo‐bridged dimeric complex ( C9 ) was isolated from the solution of the corresponding cyclopentadienyl complex ( C3 ) solution in air. Complexes C1 – C8 exhibited good to high catalytic activities toward ethylene polymerization and ethylene/α‐olefin copolymerization in the presence of methylaluminoxane (MAO) cocatalyst. In the typical catalytic system of C1/ MAO, the polymerization productivities were enhanced with either elevating reaction temperature or increasing the ratio of MAO to titanium precursor. In general, it was observed that higher the catalytic activity of the catalytic system lower the molecular weight of polyethylene. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3154–3169, 2009     

Thermo‐stable 2‐(arylimino)benzylidene‐9‐arylimino‐5,6,7,8‐tetrahydro cyclohepta[b]pyridyliron(II) precatalysts toward ethylene polymerization and highly linear polyethylenes

A series of 2‐(arylimino)benzylidene‐9‐arylimino‐5,6,7,8‐tetrahydrocyclohepta[b] pyridyliron(II) chlorides was synthesized and characterized using FT‐IR and elemental analysis, and the molecular structures of complexes Fe3 and Fe4 have been confirmed by the single‐crystal X‐ray diffraction as a pseudo‐square‐pyramidal or distorted trigonal‐bipyramidal geometry around the iron core. On activation with methylaluminoxane (MAO) or modified methylaluminoxane (MMAO), all iron precatalysts exhibited high activities toward ethylene polymerization with a marvelous thermo‐stability and long lifetime. The Fe4 /MAO system showed highest activity of 1.56 × 10⁷ gPE·mol^?1(Fe)·h^?1 at 70 °C, which is one of the highest activities toward ethylene polymerization by iron precatalysts. Even up to 80 °C, Fe3 /MAO system still persist high activity as 6.87 × 10⁶ g(PE)·mol^?1(Fe)·h^?1, demonstrating remarkable thermal stability for industrial polymerizations (80–100 °C). This was mainly attributing to the phenyl modification of the framework of the iron precatalysts. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 830–842     

Oxazoline‐terminated macromonomers by the alkylation of 2‐methyl‐2‐oxazoline

Well‐defined macromonomers of poly(ethylene oxide) and poly(tert‐butyl methacrylate) were obtained by anionic polymerization induced directly by the carbanion issued from 2‐methyl‐2‐oxazoline. When ethylene oxide was added to this carbanion with lithium as the counterion, a new compound able to initiate the polymerization of ε‐caprolactone in an anionically coordinated way was synthesized, and this led to well‐defined poly(ε‐caprolactone) macromonomers. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2440–2447, 2005     

Oxidative C‐C Coupling of Dilithium (2‐Pyridylmethanidyl)(tert‐butyldimethylsilyl)amide with White Phosphorus

(2‐Pyridylmethyl)(tert‐butyldimethylsilyl)amine ( 1 ) can be lithiated once or twice yielding lithium (2‐pyridylmethyl)(tert‐butyldimethylsilyl)amide ( 2 ) and dilithium (2‐pyridylmethanidyl)(tert‐butyldimethylsilyl)amide ( 3 ), respectively. The oxidation of 3 with white phosphorus yields dilithium 1,2‐dipyridyl‐1,2‐bis(tert‐butyldimethylsilylamido)ethane ( 4 ) which crystallizes after partial hydrolysis as an adduct of the form 2 · 4 .     

Comparison of the C1‐symmetric diastereoisomers of a zirconocene‐based catalyst in ethylene polymerization: A benzyl substituent as a regulator in branch formation

C₁‐symmetric diastereoisomers of a zirconocene dichloride, SiMe₂(3‐benzylindenyl)(indenyl)ZrCl₂, known as catalyst precursors used to produce polypropylenes with similar molecular weights and tacticities, have been investigated in ethylene polymerization. Activated by methylaluminoxane, they produce microstructurally different polymers: high‐density polyethylene and linear low‐density polyethylene, the latter characterized by the presence of ethyl branches. The formation of branches is relevant in the complex having a sterically more crowded (inward) site. A comparison with the complex without substituents, meso‐SiMe₂(indenyl)₂ZrCl₂, shows that the presence of a benzyl group on only one of the two indenyl moieties can regulate the number of branches and the molecular weight of the macromolecule. Actually, the unsubstituted complex is able to give double the number of branches and lower molecular weights, whereas the C₁‐symmetric disubstituted complexes previously reported generally give linear polyethylene. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3551–3555, 2006