Synthesis and Characterization of Triblock Terpolymers with three Potentially Crystallisable Blocks: Polyethylene-b-poly(ethylene oxide)-b-poly(ε-caprolactone)

A first attempt was made to produce novel ABC triblock terpolymers with three potentially crystallisable blocks: polyethylene (PE), poly(ethylene oxide) (PEO), and poly(ε-caprolactone) (PCL). Polybutadiene-b-poly(ethylene oxide) diblock copolymers were synthesized by living anionic polymerization. Then, a non-catalyzed thermal polymerization of ε-caprolactone from the hydroxyl end group of the PB-b-PEO diblock precursors was performed. Finally, hydrogenation by Wilkinson catalyst produced PE-b-PEO-b-PCL triblock terpolymers. Side reactions were detected that lead to the formation of undesired PCL-b-PEO diblock copolymers, however, these impurities were successfully removed by purification. A range of triblock terpolymers with PCL and PEO minor components were prepared. Topological restrictions on the PEO middle block prevented this block from crystallizing while the complex crystallization behavior of the PE and PCL blocks was documented by DSC and WAXS measurements.     

Control of morphology orientation in thin films of PS-b-PEO diblock copolymers and PS-b-PEO/resorcinol molecular complexes

One of the main limits in the use of block copolymers for nanotechnological applications lies in the poor control over the alignment of the nanoscopic domains. The self-assembling behavior of polystyrene-block-poly(ethylene oxide) (PS-b-PEO) has been modified by stoichiometric complexation of the ethylene oxide units with resorcinol and a simple procedure to prepare nanostructured films with normally oriented cylinders is reported. By direct spin coating of a series of complexated PS-b-PEO samples with different molecular weight and composition, films with the same morphology and orientation (i.e., normally oriented packed cylinders) have been obtained, also when different nanostructures and alignments were expected on the basis of the volume fraction composition and self-assembling behavior of pure copolymers. Tuning of the cylinder diameters in the range from 20 to 50 nm was possible by varying the length of the PEO block. The effects of resorcinol complexation have been studied by differential scanning calorimetry and X-ray diffraction and the morphologies of PS-b-PEO and PS-b-PEO/resorcinol films have been monitored by atomic force microscopy and electron microscopies. DSC and XRD analyses demonstrate that resorcinol significantly influences the crystallization behavior of the PEO block. The varied interfacial and surface energies of the PEO domains and the overall reduction of the crystalline phase in PS-b-PEO/resorcinol films appear to be strictly related to the morphological changes occurring by complexation.     

Thermal monitoring of morphology in triblock terpolymers with crystallizable blocks

The bulk morphology of poly(1,4‐butadiene)–block–polystyrene–block–poly (ethylene oxide) (PB‐b‐PS‐b‐PEO) and polyethylene–block–polystyrene–block–poly (ethylene oxide) (PE‐b‐PS‐b‐PEO) triblock terpolymers is analyzed under a thermal protocol. This allows the investigation of the morphology during the occurrence of thermal transitions, such as crystallization and melting, which is a neat way of studying the competition between microphase separation and crystallization for the morphology formation. Only one of the studied systems presented a morphological transition upon melting of the PEO and the PE blocks, attributed to the crystallization of the PE block in finite interconnected domains. All the other systems presented no morphological transitions during the thermal scan. The results prove that the crystallization only disrupt the microphases generated in the molten state under very specific circumstances for these block copolymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3197–3206, 2007     

Synthesis and characterization of a poly(para-phenyleneethynylene)-block-poly(ethylene oxide) rod-coil block copolymer

The synthesis of the poly(para-phenyleneethynylene)-block-poly(ethylene oxide) block copolymer (PPE-b-PEO) ( 1 ) via condensation of endfunctionalized poly(para-phenyleneethynylene) (PPE) ( 5 ) and poly(ethylene oxide) monomethyl ether (PEO) is reported. This is achieved by the initial synthesis of a PPE homopolymer with quantitative terminal functionalization, as proven by ¹H NMR and field desorption mass spectrometry (FD-MS). Reaction of the latter with PEO affords the block copolymer 1 , which was characterized by ¹H NMR spectroscopy, FD-MS and gel permeation chromatography (GPC). Furthermore it is shown that matrix assisted laser desorption ionization-time of flight mass spectrometry (MALDI-TOF-MS) is a suitable method to investigate PPE-b-PEO with respect to molecular weights and copolymer composition.     

Nucleation and crystallization of PS-b-PEO-b-PCL triblock copolymers

We have recently prepared a series of Polystyrene-b-Poly(ethylene oxide)-b-Polycaprolactone (PS-b-PEO-b-PCL or SEOCL) triblock copolymers of varying compositions and molecular weights. These ABC triblock copolymers present the peculiarity that two of the three blocks are able to crystallize upon cooling from an already phase segregated melt. When either of the crystallizable blocks or both are a minor phase, a fractionated crystallization process develops. The confinement of crystallizable blocks in the nanoscopic scale enables the clear observation in some cases of exclusive crystallization from homogeneous nuclei of two components within the triblock copolymer. The homogeneous nature of the nucleation was deduced since the supercooling attained is the maximum possible before vitrification of the material takes place. The self-nucleation domains were also found to depend on the composition and molecular weight of the copolymers. The block copolymers exhibited a marked decrease in crystalline memory and when the crystallizable blocks constitute minor phases, the self-nucleation domain disappears. The reason behind this behavior is that only at lower self-nucleation temperatures the density of self-nuclei becomes high enough to include at least one crystal fragment per confined microdomain in view of their vast numbers (e.g., 10¹⁶/cm³).     

Crystallization-induced aggregation of block copolymer micelles: influence of crystallization kinetics on morphology

We present a systematic investigation of the crystallization and aggregation behavior of a poly(1,2-butadiene)-block-poly(ethylene oxide) diblock copolymer (PB-b-PEO) in n-heptane. n-Heptane is a poor solvent for PEO and at 70°C the block copolymer self-assembles into spherical micelles composed of a liquid PEO core and a soluble PB corona. Time- and temperature-dependent light scattering experiments revealed that when crystallization of the PEO cores is induced by cooling, the crystal morphology depends on the crystallization temperature (T _c ): Below 30°C, the high nucleation rate of the PEO core dictates the growth of the crystals by a fast aggregation of the micelles into meander-like (branched) structures due to a depletion of the micelles at the growth front. Above 30°C the nucleation rate is diminished and a relatively small crystal growth rate leads to the formation of twisted lamellae as imaged by scanning force microscopy. All data demonstrate that the formation mechanism of the crystals through micellar aggregation is dictated by two competitive effects, namely, by the nucleation and growth of the PEO core.     

Hydrogen bond mediated self-assembly of two diblock copolymers

Two chemically dissimilar diblock copolymers, polybutadiene-b-poly(acrylic acid), PBd-b-PAA (M_w = 5.8–4 kg mol⁻¹) and poly(styrene)-b-poly(ethylene oxide), PS-b-PEO (M_w = 9–5 kg mol⁻¹) were blended in an effort to achieve morphologies typical of triblock copolymers. Blend compatibility was achieved by the hydrogen bond driven association of the PAA block of one diblock with the PEO block of the other. Small angle X-ray scattering was used to determine the morphologies of the compositions, which were further investigated using transmission electron microscopy and selective staining techniques. The crystallinity of the PEO block was determined by differential scanning calorimetry. The hydrogen bond interactions between PEO and PAA yielded a complex triblock lamellar morphology of the form PS-b-(PEO/PAA)-b-PBd-b-(PEO/PAA). This morphology was stable when crystallization of PEO was suppressed by sufficient interaction with PAA.     

Crystallization and Physical Ageing of Poly (2-vinyl pyridine)-b-poly(ethylene oxide) Diblock Copolymers

Summary: A set of melt miscible Poly(2-vinyl pyridine)-b-Poly(ethylene oxide) (P2VP-b-PEO) block copolymers of different compositions were studied. Transmission electron microscopy shows phase separation in the materials during the crystallization process of the PEO block as crystalline lamellae are observed for all compositions evaluated. The isothermal crystallization kinetics of PEO is progressively retarded as the P2VP content in the copolymer increases, since P2VP hinders molecular mobility in the miscible amorphous phase. Polarized light optical microscopy demonstrated that the glassy P2VP block has a negative effect on the secondary nucleation of the PEO. Finally, physical ageing experiments performed in the glassy state of the amorphous mixed phase, at different ageing times, demonstrated that a nucleating effect can be induced in the glassy state as a consequence of the reorganization of the amorphous regions. This nucleating effect significantly alters the cold crystallization rate upon subsequent heating above the glass transition temperature.     

Synthesis and micelle formation of triblock copolymers of poly(methyl methacrylate)-b-poly(ethylene oxide)-b-poly(methyl methacrylate) in aqueous solution

Amphiphilic triblock copolymers of poly(methyl methacrylate)-b-poly(ethylene oxide)-b-poly(methyl methacrylate) (PMMA-b-PEO-b-PMMA) with well-defined structure were synthesized via atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) initiated by the PEO macroinitiator. The macroinitiator and triblock copolymer with different PMMA and/or PEO block lengths were characterized with ¹H and ¹³C NMR and gel permeation chromatography (GPC). The micelle formed by these triblock copolymers in aqueous solutions was detected by fluorescence excitation and emission spectra of pyrene probe. The critical micelle concentration (CMC) ranged from 0.0019 to 0.016 mg/mL and increased with increasing PMMA block length, while the PEO block length had less effect on the CMC. The partition constant K_v for pyrene in the micelle and in aqueous solution was about 10⁵. The triblock copolymer appeared to form the micelles with hydrophobic PMMA core and hydrophilic PEO loop chain corona. The hydrodynamic radius R_h,app of the micelle measured with dynamic light scattering (DLS) ranged from 17.3 to 24.0 nm and increased with increasing PEO block length to form thicker corona. The spherical shape of the micelle of the triblock copolymers was observed with an atomic force microscope (AFM). Increasing hydrophobic PMMA block length effectively promoted the micelle formation in aqueous solutions, but the micelles were stable even only with short PMMA blocks.     

Hierarchical mesostructures of biodegradable triblock copolymers via evaporation-induced self-assembly directed by alkali metal ions

Hierarchical mesostructures of poly(ε-caprolactone)-b-poly(ethylene oxide)-b-poly(ε-caprolactone) (PCL-PEO-PCL) triblock copolymers have been grown from evaporation-induced self-assembly directed by alkali metal ions. The self-assembly process began with a dilute homogeneous solution of the triblock copolymers in a mixture of tetrahydrofuran (THF) and water. THF preferentially evaporated under reduced pressure and induced the formation of amphiphilic polymer micelles. The spherical polymer micelles formed both in deionized water and NaOH aqueous solution. However, different mesostructures were discovered during the film depositing process for scanning electron microscopy observation. The polymer micelles were observed for the deposition sample in deionized water while sisal-like hierarchical mesostructures resulted from the film deposition of polymer micelles in NaOH aqueous solution. The sisal-like mesostructures and their formation process were observed through scanning electron microscopy, transmission electron microscopy, fluorescent microscopy, X-ray diffraction, and Fourier transform infrared spectroscopy. Detailed study revealed that during evaporation-induced self-assembly of PCL-PEO-PCL amphiphilic triblock copolymer directed by alkali metal ions, the sodium ions and polymer micelles increasingly concentrated in NaOH aqueous solution and the solvent quality for the diblock progressively decreased, which resulted in the stronger coordination between alkali metal ions and PEO ligands in the block copolymer and PEO segment crystallization.     

Synthesis of poly(N,N‐dimethylacrylamide)‐block‐poly(ethylene oxide)‐block‐poly(N,N‐dimethylacrylamide) and its application for separation of proteins by capillary zone electrophoresis

A series of well‐defined triblock copolymers, poly(N, N‐dimethylacrylamide)‐block‐poly(ethylene oxide)‐block‐poly(N, N‐dimethylacrylamide) (PDMA‐b‐PEO‐b‐PDMA) synthesized by atom transfer radical polymerization, were used as physical coatings for protein separation. A comparative study of EOF showed that the triblock copolymer presented good capillary coating ability and EOF efficient suppression. The effects of the M_r of PDMA block in PDMA‐b‐PEO‐b‐PDMA triblock copolymer and buffer pH on the separation of basic protein for CE were investigated. Moreover, the influence of the copolymer structure on separation of basic protein was studied by comparing the performance of PDMA‐b‐PEO‐b‐PDMA triblock copolymer with PEO‐b‐PDMA diblock copolymer. Furthermore, the triblock copolymer coating showed higher separation efficiency and better migration time repeatability than fused‐silica capillary when used in protein mixture separation and milk powder samples separation, respectively. The results demonstrated that the triblock copolymer coatings would have a wide application in the field of protein separation.     

Reaction-induced microphase separation in epoxy resin containing polystyrene-block-poly(ethylene oxide) alternating multiblock copolymer

Polystyrene-block-poly(ethylene oxide) alternating multiblock copolymer (PS-alt-PEO) was synthesized with the combination of atom transfer radical polymerization (ATRP) and Huisgen 1,3-dipolar cycloaddition (i.e., click chemistry). The copolymer has been characterized by means of Fourier transform infrared spectroscopy (FTIR), ¹H nuclear magnetic resonance spectroscopy (NMR), gel permeation chromatography (GPC) and differential scanning calorimetry (DSC). The PS-alt-PEO alternating multiblock copolymer was incorporated into epoxy resin to investigate the behavior of reaction-induced microphase separation, which has been compared to the case of the thermosets containing PS-b-PEO diblock copolymer. The morphology of epoxy thermosets containing PS-alt-PEO alternating multiblock copolymer were investigated by means of atomic force microscopy (AFM), and small-angle X-ray scattering (SAXS) and the nanostructures were detected in all the thermosetting blends investigated. In marked contrast to the case of the thermosets containing PS-b-PEO diblock copolymer, the thermosets containing PS-alt-PEO multiblock copolymer displayed disordered nanostructures, which have been interpreted on the basis of the restriction of the alternating multiblock topology of the block on the formation of the nanostructures via reaction-induced microphase separation.     

Nanoscale-confined crystallization in epoxy resin and polyethylene-block-poly(ethylene oxide) diblock copolymer blends

In this paper, the nanoscale-confined crystallization behavior and crystallization kinetics in blends of double-crystalline polyethylene-block-poly(ethylene oxide) (PE-b-PEO) diblock copolymer with diglycidyl ether of bisphenol A epoxy resin were investigated. The results showed that there appeared three crystallization regimes related to the crystallization of the PE block within three different microenvironments in the epoxy resin/PE-b-PEO blends. The Avrami index n is around 1.8–2.4, suggesting PE block of the copolymer in the blends exhibited nanoscale-confined crystallization behavior by homogeneous nucleation. The PE block nanoscale-confined crystallization is ascribed to the formation of the strong intermolecular hydrogen bonding interaction between hydroxyl groups of amine-cured epoxy and ether oxygen atoms of PEO, as seen from Fourier transform infrared spectroscopy spectra.     

ABA triblock copolymer containing two crystallizable components

A triblock copolymer of the ABA type in which both components were crystallizable was synthesized. The A block was poly(ethylene oxide), PEO, and the B block, poly(dimethyl siloxane), PDMS. Upon cooling from the melt to liquid nitrogen temperature, the PEO block crystallized at around 40°C. When the copolymer was heated from ?170°C after quenching, glass transition, crystallization and melting of the PDMS middle block were identified in the thermogram at ?117°C, ?74°C and ?42°C, respectively. The degree of crystallinity of the PDMS block was estimated from the heat of fusion to be about 27%. The growth rates of the PEO spherulites were reduced by the presence of the middle block.     

Novel Amphiphilic Diblock and Triblock Liquid‐Crystalline Copolymers with Well‐Defined Structures Prepared by Atom Transfer Radical Polymerization

Summary: Based on a hydrophilic poly(ethylene oxide) macroinitiator (PEOBr), a novel amphiphilic diblock copolymer PEO‐block‐poly(11‐(4‐cyanobiphenyloxy)undecyl) methacrylate) (PEO‐b‐PMA(11CB)) was prepared by atom transfer radical polymerization (ATRP) using CuCl/1,1,4,7,10,10‐hexamethyltriethylenetriamine as a catalyst system. An azobenzene block of poly(11‐[4‐(4‐butylphenylazo)phenoxyl]undecyl methacrylate) was then introduced into the copolymer sequence by a second ATRP to synthesize the corresponding triblock copolymer PEO‐b‐PMA(11CB)‐b‐PMA(11Az). Both of the amphiphilic block copolymers had well‐defined structures and narrow molecular‐weight distributions, and exhibited a smectic liquid‐crystalline phase over a wide temperature range.

The amphiphilic triblock copolymer synthesized here.     

Functionalized nanoporous thin films from metallo-supramolecular diblock copolymers

A polystyrene-[Ni(2+)]-poly(ethylene oxide) metallo-supramolecular block copolymer (PS-[Ni(2+)]-PEO), where -[ is a terpyridine, is used to create nanoporous thin films with free terpyridine ligands homogenously distributed on the pore walls. The PS-[Ni(2+)]-PEO block copolymer is synthesized by a two step assembly process, and is then self-assembled into a thin film in order to obtain PEO cylinders oriented perpendicularly to the film surface. The supramolecular junction is opened by exposing the film to an excess of a competing ligand, and the free PEO block is then rinsed away by a selective solvent. The presence of the terpyridines on the pore walls is evidenced by fluorescence spectroscopy after formation of a fluorescent complex with an europium salt.     

Synthesis of a Novel ABC Triblock Copolymer with a Rigid‐Rod Block via Atom Transfer Radical Polymerization

Summary: A novel ABC triblock copolymer with a rigid‐rod block was synthesized by atom transfer radical polymerization (ATRP). First, a poly(ethylene oxide) (PEO)‐Br macroinitiator was synthesized by esterification of PEO with 2‐bromoisobutyryl bromide, which was subsequently used in the preparation of a poly(ethylene oxide)‐block‐poly(methyl methacrylate) (PEO‐b‐PMMA) diblock copolymer by ATRP. A poly(ethylene oxide)‐block‐poly(methyl methacrylate)‐block‐poly{2,5‐bis[(4‐methoxyphenyl)oxycarbonyl]styrene} (PEO‐b‐PMMA‐b‐PMPCS) triblock copolymer was then synthesized by ATRP using PEO‐b‐PMMA as a macroinitiator.

ABC triblock copolymer with a rigid‐rod block.     

PEO-PPO-PEO水溶液体系胶束化及凝胶化行为的耗散粒子动力学模拟

采用耗散粒子动力学(Dissipative particle dynamics, DPD)模拟方法研究了三嵌段共聚物聚氧乙烯-聚氧丙烯-聚氧乙烯(PEO-PPO-PEO)的胶束化和凝胶化行为. 通过模拟得到了F127(EO₉₉PO₆₅EO₉₉)水溶液的临界胶束浓度和临界凝胶浓度. 结果发现, 在298 K、 质量分数低于40%时, F127水溶液中形成的胶束形状均为球形. 此外,进一步研究了亲水嵌段长度对胶束结构及凝胶形成浓度的影响, 结果发现, 亲水嵌段越短, 越有利于长椭球状胶束的形成, 而临界凝胶浓度随着亲水嵌段PEO长度的增加而降低.     

A Simple and Effective Approach to Vesicles and Large Compound Vesicles via Complexation of Amphiphilic Block Copolymer With Polyelectrolyte in Water

This work reports for the first time a simple and effective approach to trigger a spheres‐to‐ vesicles morphological transition from amphiphilic block copolymer/polyelectrolyte complexes in aqueous solution. Vesicles and large compound vesicles (LCVs) were prepared via complexation of polystyrene‐block‐poly(ethylene oxide) (PS‐b‐PEO) with poly(acrylic acid) (PAA) in water and directly visualized using cryo‐TEM. The complexation and morphological transitions were driven by the hydrogen bonding between the complementary binding sites on the PAA and PEO blocks of the block copolymer. The findings in this work suggest that complexation between amphiphilic block copolymer and polyelectrolyte is a viable approach to vesicles and LCVs in aqueous media.