Miscibility of poly(ethylene terephthalate)/poly(ethylene 2,6-naphthalate) blends by transesterification

The effects of transesterification on the miscibility of poly(ethylene terephthalate)/poly(ethylene 2,6-naphthalate) were studied. Blends were obtained by solution precipitation at room temperature to avoid transesterification during blend preparation. The physical blends and transesterified products were analyzed by wide-angle x-ray scattering, differential scanning calorimetry, and nuclear magnetic resonance spectroscopy. It was found that the physical blends are immiscible and when the extent of transesterification reaches 50% of the completely randomized state, independent of blend composition, the blends are not crystallizable and show a single glass transition temperature between those of starting polymers. The interchange reactions were significantly influenced by annealing temperature and time but negligibly by blend composition. © 1996 John Wiley & Sons, Inc.     

Thermal,crystallization, mechanical,and rheological characteristics of poly(trimethylene terephthalate)/poly(ethylene terephthalate) blends

Blends of poly(trimethylene terephthalate) (PTT) and poly(ethylene terephthalate) in the amorphous state were miscible in all of the blend compositions studied, as evidenced by a single, composition‐dependent glass‐transition temperature observed for each blend composition. The variation in the glass‐transition temperature with the blend composition was well predicted by the Gordon–Taylor equation, with the fitting parameter being 0.91. The cold‐crystallization (peak) temperature decreased with an increasing PTT content, whereas the melt‐crystallization (peak) temperature decreased with an increasing amount of the minor component. The subsequent melting behavior after both cold and melt crystallizations exhibited melting point depression behavior in which the observed melting temperatures decreased with an increasing amount of the minor component of the blends. During crystallization, the pure components crystallized simultaneously just to form their own crystals. The blend having 50 wt % of PTT showed the lowest apparent degree of crystallinity and the lowest tensile‐strength values. The steady shear viscosity values for the pure components and the blends decreased slightly with an increasing shear rate (within the shear rate range of 0.25–25 s^?1); those of the blends were lower than those of the pure components. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 676–686, 2004     

The influence of vacuum-ultraviolet radiation on poly(ethylene terephthalate)

Poly(ethylene terephthalate) was exposed to radiation from different kinds of low-pressure plasmas in an oxygen atmosphere. The lower wavelength limit of the spectrum investigated, λ = 112 nm, is the cut-off of magnesium fluoride used for separating the specimen chamber from the plasma light source. The total surface oxygen concentration, and the formation of hydroxyl, carbonyl, and carboxyl groups were evaluated from XPS measurements in combination with chemical derivatizations, and their dependences on the radiation spectrum and the oxygen pressure in the sample chamber have been investigated. © 1996 John Wiley & Sons, Inc.     

Segmented block copolymers of poly(ethylene glycol) and poly(ethylene terephthalate)

A new series of segmented copolymers were synthesized from poly(ethylene terephthalate) (PET) oligomers and poly(ethylene glycol) (PEG) by a two‐step solution polymerization reaction. PET oligomers were obtained by glycolysis depolymerization. Structural features were defined by infrared and nuclear magnetic resonance (NMR) spectroscopy. The copolymer composition was calculated via ¹H NMR spectroscopy. The content of soft PEG segments was higher than that of hard PET segments. A single glass‐transition temperature was detected for all the synthesized segmented copolymers. This observation was found to be independent of the initial PET‐to‐PEG molar ratio. The molar masses of the copolymers were determined by gel permeation chromatography (GPC). © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4448–4457, 2004     

非晶聚对苯二甲酸乙二酯的制备与表征

采用引入U-polymer的路线制备了非晶聚对苯二甲酸乙二酯(APET).用DSC和DMA等手段研究了APET的性能.结果表明,经改性后得到的APET无结晶,透明性得到改善,玻璃化转变温度和储能模量都较PET有一定程度提高.     

High‐pressure DTA of poly(butylene terephthalate), poly(hexamethylene terephthalate), and poly(ethylene terephthalate)

Pressure effect on the melting behavior of poly(butylene terephthalate) (PBT) and poly(hexamethylene terephthalate) (PHT) was studied by high‐pressure DTA (HP‐DTA) up to 320 and 530 MPa, respectively. Cooling rate dependence on the DSC melting curves of the samples cooled from the melt was shown at atmospheric pressure. Stable and metastable samples were prepared by cooling from the melt at low and normal cooling rates, respectively. DTA melting curves for the stable samples showed a single peak, and the peak profile did not change up to high pressure. Phase diagrams for PBT and PHT were newly determined. Fitting curves of melting temperature (T_m) versus pressure expressed by quadratic equation were obtained. Pressure coefficients of T_m at atmospheric pressure, dT_m/dp, of PBT and PHT were 37 and 33 K/100 MPa, respectively. HP‐DTA curves of the metastable PBT showed double melting peaks up to about 70 MPa. In contrast, PHT showed them over the whole pressure region. HP‐DTA of stable poly(ethylene terephthalate) (PET) was also carried out up to 200 MPa, and the phase diagram for PET was determined. dT_m/dp for PET was 49 K/100 MPa. dT_m/dp increased linearly with reciprocal number of ethylene unit. The decrease of dT_m/dp for poly(alkylene terephthalate) with increasing a segmental fraction of an alkyl group in a whole molecule is explained by the increase of entropy of fusion. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 262–272, 2000     

Swelling-assisted modification of poly(ethylene terephthalate) by methacrylic acid

When a poly(ethylene terephthalate), PET, film is heated in an aqueous solution of methacrylic acid in the presence of hydrogen peroxide as an initiator, it is found that the weight of the film is increased. The amount of methacrylic acid that may be added onto the film is dependent upon the concentration of the monomer, the initiator, and the temperature at which the reaction occurs. Pretreatment of the film with 1,1,2,2,tetrachloroethane causes swelling and the amount of add-on is increased as the swelling level increases. Methacrylic-acid-modified PET films hydrolyze at room temperature in aqueous sodium hydroxide; the rate of hydrolysis is dependent upon the amount of add-on and the concentration of the base. This procedure leads to a chemically induced blend of polymethacrylic acid and poly(ethylene terephthalate), and grafting of the monomer onto the polymer film does not occur. © 1995 John Wiley & Sons, Inc.     

An evoluted bio-based 2,5-furandicarboxylate copolyester fiber from poly(ethylene terephthalate)

A series of bio-based poly(ethylene terephthalate-co-ethylene 2,5-furandicarboxylate) (PEFT) fibers was prepared via the industrially feasible melt-spinning and hot-drawing process. The effect of 2,5-furandicarboxylic acid (FDCA) content on the fibers properties was studied using differential scanning calorimetry, wide-angle X-ray diffraction, sound velocity, tensile, and boiling water shrinkage tests. It was found that the PEFT fibers showed comparable or superior tenacity to the PET fibers under the same conditions, especially the PEFT-4 fibers exhibited the highest tenacity (2.3, 2.9 cN/dtex for the drawn PET and PEFT-4 fibers prepared at the same take-up speed of 2500 m/min and a fixed draw ratio of 1.6). Moreover, the boiling water shrinkage of the PEFT fibers was quite close to that of the PET fibers under the same conditions, showing that the PEFT fibers were comparable to the PET fibers in heat resistance. The results indicated that the bio-based PEFT fibers would be a feasible alternative for the PET fibers, in terms of sustainability, processability, and mechanical properties. © 2020 Wiley Periodicals, Inc. J. Polym. Sci. 2020 , 58, 320–329     

NMR study of ester-interchange reactions during melt mixing of poly(ethylene terephthalate)/poly(butylene terephthalate) blends

The occurrence of ester-interchange reactions during PET/PBT blend processing has been confirmed by ¹³C-NMR measurements. The limitations of the method for precise quantification of the extent of reaction between high molecular weight polyester blends have also been pointed out. Titanium alkoxide has been confirmed as an efficient catalyst, and, within experimental precision, the stabilizing effect of triphenyl phosphite addition has been demonstrated. © 1996 John Wiley & Sons, Inc.     

Interval kinetic gravimetric sorption of acetone in random copolymers of poly(ethylene terephthalate) and poly(ethylene 2,6-naphthalate)

Interval sorption kinetics of acetone in solvent cast films of random poly(ethylene terephthalate)-co-(ethylene 2,6-naphthalate) (PET-co-PEN) are reported at 35°C and at acetone pressures ranging from 0 to 7.3 cm Hg. Polymer composition is varied systematically from 0% to 50% poly(ethylene 2,6-naphthalate). Equilibrium sorption is well described by the dual-mode sorption model. Interval sorption kinetics are described using a two-stage model that incorporates both Fickian diffusion and protracted polymer structural relaxation. The incorporation of low levels of PEN into PET significantly reduces the excess free volume associated with the glassy state and, for these interval acetone sorption experiments in ∼ 5 μm-thick films, decreases the fraction of acetone uptake controlled by penetrant-induced polymer structural relaxation. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2973–2984, 1999     

Mechanistic investigations of antimony‐catalyzed polycondensation in the synthesis of poly(ethylene terephthalate)

The chemical aspects of poly(ethylene terephthalate) synthesis via the antimony‐catalyzed polycondensation of hydroxy ethylene terephthalate end groups were studied to elucidate its mechanism. A polycondensation mechanism was proposed in which activation occurs by the formation of a chelate ligand on antimony composed of the hydroxyl end group and alcoholic oxygen of the ester of the same end group. The rate‐determining step of the polycondensation reaction was concluded to be the coordination of a second chain end to antimony. The low activity of antimony at a high concentration of hydroxyl end groups was proposed to result from the competition between hydroxyl end groups and the chelate structure leading to the transition state. The high selectivity of antimony is probably due to its relatively low Lewis acidity. Moreover, antimony was found to stabilize hydroxyl end groups against degradation by preventing their complexation to carbonyl functionalities. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1049‐1059, 2006     

Quasi-liquid composites based on poly(ethylene terephthalate) films with fullerene and dichlorobenzene

Quasi-liquid composites based on poly(ethylene terephthalate) (PET) films with 9 wt% solution of the C₆₀ (70%) and C₇₀ (∼30%) fullerenes mixture in dichlorobenzene (DCB) have been obtained. It has been shown that PET swelling in the fullerene solution in DCB is accompanied by penetration of fullerene into the polymer structure, and PET films are deformed by the mechanism of intercrystallite crazing. As has been revealed by UV spectroscopy, fullerene incorporated into composite remains monomeric as in solution.     

Water sorption/desorption kinetics in poly(ethylene naphthalene-2,6-dicarboxylate) and poly(ethylene terephthalate)

Water sorption/desorption experiments were carried out on films (～ 220 μm thick) of amorphous poly(ethylene naphthalene-2,6-dicarboxylate) (PEN) stored in ambient conditions for different periods of time (0.5-4 years) and of poly(ethylene terephthalate) (PET) with different degrees of crystalinity levels (0-29%) by means of FTIR spectroscopy. Water sorption/desorption kinetics follows Fick's law for all samples investigated. Water sorption isotherms, obtained from gravimetric methods, indicate a larger sorption capacity in the case of PEN materials. The apparent diffusion coefficients (D) are larger in the case of PET samples. The observed D values decrease with storage time (physical aging) of PEN samples and with the crystallinity of PET samples. © 1995 John Wiley & Sons, Inc.     

Synthesis and characterization of poly(ethylene glycol) methyl ether endcapped poly(ethylene terephthalate)

Linear and branched poly(ethylene terephthalate) (PET) copolymers with polyethylene glycol) (PEG) methyl ether (700 or 2000 g/mol) end groups were synthesized using conventional melt polymerization. DSC analysis demonstrated that low levels of PEG end groups accelerated PET crystallization. The incorporated PEG end groups also decreased the crystallization temperature of PET dramatically, and copolymers with a high content of PEG (>17.6 wt%) were able to crystallize at room temperature. Rheological analysis demonstrated that the presence of PEG end groups effectively decreased the melt viscosities and facilitated melt processing. XPS and ATR-FTIR revealed that the PEG end groups tended to aggregate on the surface, and the surface of compression molded films containing 34.0 wt% PEG were PEG rich (85 wt% PEG). PEG end-capped PET (34.0 wt% PEG) and PET films were immersed into a fibrinogen solution (0.7 mg/mL BSA) for 72 h to investigate the propensity for protein adhesion. XPS demonstrated that the concentration of nitrogen (1.05%) on the surface of PEG endcapped PET film was statistically lower than PET (7.67%). SEM analysis was consistent with XPS results, and revealed the presence of adsorbed protein on the surface of PET films.     

Organocatalytic depolymerization of poly(ethylene terephthalate)

We describe the organocatalytic depolymerization of poly(ethylene terephthalate) (PET), using a commercially available guanidine catalyst, 1,5,7‐triazabicyclo[4.4.0]dec‐5‐ene (TBD). Postconsumer PET beverage bottles were used and processed with 1.0 mol % (0.7 wt %) of TBD and excess amount of ethylene glycol (EG) at 190 °C for 3.5 hours under atmospheric pressure to give bis(2‐hydroxyethyl) terephthalate (BHET) in 78% isolated yield. The catalyst efficiency was comparable to other metal acetate/alkoxide catalysts that are commonly used for depolymerization of PET. The BHET content in the glycolysis product was subject to the reagent loading. This catalyst influenced the rate of the depolymerization as well as the effective process temperature. We also demonstrated the recycling of the catalyst and the excess EG for more than 5 cycles. Computational and experimental studies showed that both TBD and EG activate PET through hydrogen bond formation/activation to facilitate this reaction. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Effect of silica nanoparticles on solid state polymerization of poly(ethylene terephthalate)

In the present study, the effect of silica nanoparticles, on the solid state polycondensation (SSP) kinetics of poly(ethylene terephthalate) (PET) is thoroughly investigated. At silica concentrations less than 1 wt% and reaction temperatures between 200 and 230 °C higher intrinsic viscosity (IV) values were measured, compared to neat PET at all reaction times. However, with 1 wt% of nanosilica (n-SiO₂), the IV increase of the nanocomposites was similar to that of neat PET and a further increase to 5 wt% n-SiO₂ resulted in significantly lower IV values. A simple kinetic model was also employed to predict the time evolution of IV, as well as the carboxyl and hydroxyl content during SSP. The kinetic parameters of the transesterification and esterification reactions were estimated at different temperatures with or without the addition of n-SiO₂. The activation energies of both reactions were determined together with the concentration of inactive end-groups. From the experimental measurements and the theoretical simulation results it was proved that n-SiO₂ in small amounts (less than 1 wt%) enhances both the esterification and transesterification reactions at all studied temperatures acting as a co-catalyst. However, as the amount of nanosilica increases a number of inactive hydroxyl groups were estimated corresponding to participation of these groups in side reactions with the nanosilica particles. These side reactions lead initially to branched PET chains and eventually (5 wt% n-SiO₂ concentration) to crosslinked structures.     

Structural features of crystallized poly(ethylene terephthalate) polymers

Polyethylene terephthalate (PET) is a widely used polymeric material. In this work, the microstructural features before and after the solid‐state polymerization (SSP) of several DuPont PET products were investigated by low‐voltage scanning electron microscopy (LV‐SEM) and atomic force microscopy (AFM). The microstructural features on the cross section of various PET samples included crystallites, voids, boundaries, defects, and amorphous phases. The SEM images revealed layered and stepped structural features at the micron and 10‐micron scales that are highly crystallized at the near‐edge region of the cross section for both linear and branched PET samples after the SSP process. The AFM images demonstrate that the degree of crystallization for the linear and branched PET samples increases gradually from the central area to the edge on the cross section. The linear crystallized PET has a higher degree of orientation than the branched crystallized PET in the 10‐micron to micron scales, but their crystalline structures have no significant differences in the submicron to nanometer scales. The PET crystallization process occurs when the molecular chains in the amorphous phase are aligned and folded to form straight molecular chains at the nanometer scale, and small crystallites are formed. The crystallites aggregate and align together into a polygon rod‐like‐shaped crystallites at the submicron scale. Finally, large crystallites at the micron size are formed that appear on the edge area of the cross section. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 245–254, 2002     

Acetone transport in poly(ethylene terephthalate) and related phenomena

The acetone transport in poly(ethylene terephthalate) (PET) and related phenomena was investigated. Based on Harmon's model for Case I, Case II, and the anomalous transport, we analyzed the data of mass uptake. The diffusivity for Case I and the velocity for Case II satisfied the Arrhenius plot. It was found that the solvent moves from outer surfaces to the center according to Case I kinetics, and there is movement in the opposite direction according to Case II kinetics during the mass uptake. This result indicated that pure Case II behavior did not appear in the PET–acetone system. The saturated amount of acetone in PET satisfied the van't Hoff plot. X-ray diffraction pattern and DSC curve showed solvent-induced crystallites and thermal crystallites. The results of density measurement explained the difference of the sorption kinetics between the acetone-treated PET crystallites and thermally treated PET. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36 : 163–169, 1998     

Subglass-transition-temperature annealing of poly(ethylene terephthalate) studied by FTIR

Using FTIR spectroscopy we have examined conformational changes in the quenched and slowly cooled amorphous PET films during physical aging process. It was observed that the amount of trans conformers for quenched sample decreased upon sub-T_g annealing. For the slowly cooled sample that corresponds to a state closer to equilibrium, the amount of trans conformers hardly decreased, but increased gradually during sub-T_g annealing process. The conformational populations of these two samples tend to be identical with annealing time. These results demonstrate that sub-T_g annealing will lead to closer interchain packing and result in the formation of new cohesional entanglements along the chains. In situ FTIR studies on the conformational changes of these samples were also carried out during heating up of the sample through the glass transition region. The results showed that incremental changes of the amount of trans conformers in Samples Q and SC were gradual, while an abrupt change of trans conformers occurred in the sub-T_g annealed samples. These results were in agreement with the formation of the interchain cohesional entanglement due to sub-T_g annealing. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 783–788, 1998     

Solubility parameters of poly(sulfonyldiphenylene phenylphosphonate) and its miscibility with poly(ethylene terephthalate)

The solubility behaviors of poly(sulfonyldiphenylene phenylphosphonate) (PSPPP), a very efficient flame retardant for poly(ethylene terephthalate) (PET), in more than 50 solvents were examined. Its solubility parameters (δ) were determined by the intrinsic viscosity and turbidic titration methods. The two methods obtained consistent results, δ = 21.0–21.6 J^1/2/cm^3/2 and δ = 21.0 J^1/2/cm^3/2, and the three‐dimensional solubility parameters were δ_d = 18.9 J^1/2/cm^3/2, δ_p = 8.8 J^1/2/cm^3/2, and δ_h = 5.9 J^1/2/cm^3/2. The miscibility of PSPPP with PET was estimated by the calculation of the heats of mixing, which were related to the difference between the solubility parameters of PSPPP and PET. Fourier transform infrared was used to examine the interactions between PSPPP and PET macromolecules, which were the internal factors of polymer–polymer miscibility. The results showed that PSPPP and PET were miscible within a very wide composition range, especially with less than 15 wt % PSPPP, a composition of interest for the preparation of flame‐retardant PET. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2296–2301, 2003