两亲性PS-b-PEG嵌段共聚物刷的合成及响应行为

利用原子转移自由基聚合(ATRP)和点击化学(Click)反应, 在硅基底上制备了聚苯乙烯-b-聚乙二醇(PS-b-PEG)两亲性嵌段共聚物刷. 首先, 利用ATRP方法在表面改性的硅片引发苯乙烯单体(St)的聚合, 得到PS-Br均聚刷, 然后通过叠氮化钠(NaN₃)将均聚刷末端功能化为PS-N₃, 再与炔基聚乙二醇甲醚(Alkynyl-PEG)发生Click反应, 得到PS-b-PEG嵌段共聚物刷. 通过X射线光电子能谱(XPS)和接触角测量仪表征了聚合物刷的表面化学组成和表面亲疏水性质, 证明在硅基底上接枝了嵌段共聚物刷. 用原子力显微镜(AFM)观察了PS-b-PEG嵌段共聚物刷在不同溶剂处理后的形态结构变化, 研究了其响应行为.     

Molecularly asymmetric triblock copolymers as a single-molecule route to ordered bidisperse polymer brushes

The conditions signaling the formation of bidisperse brushes in ordered block copolymers are investigated as an A(2) block is progressively grown onto an A(1)B diblock copolymer to form a series of molecularly asymmetric, isomorphic A(1)BA(2) triblock copolymers. Small-angle scattering and self-consistent field theory confirm that the microphase-ordered period decreases when the A(2) block is short relative to the A(1) block, but then increases as A(1)+A(2) bidisperse brushes develop. The mechanical properties systematically follow the spatial distribution of the A(2) block.     

Homopolymer and block copolymer brushes on gold by living anionic surface‐initiated polymerization in a polar solvent

Living anionic surface‐initiated polymerization on flat gold substrates has been conducted to create uniform homopolymer and diblock copolymer brushes. A 1,1‐diphenylethylene (DPE) self‐assembled monolayer was used as the immobilized precursor initiator. n‐BuLi was used to activate the DPE in tetrahydrofuran at –78 °C to initiate the polymerization of different monomers (styrene, isoprene, ethylene oxide, and methyl methacrylate). Poly(styrene) (PS) and poly(ethylene oxide) (PEO) in particular were first investigated as grafted homopolymers, followed by their copolymers, including poly(isoprene)‐b‐poly(methylmethacrylate) (PI‐b‐PMMA). A combined approach of spectroscopic (Fourier transform infrared spectroscopy, surface plasmon spectroscopy, ellipsometry, X‐ray photoelectron spectroscopy) and microscopic (atomic force microscopy) surface analysis was used to investigate the formation of the polymer brushes in polar solvent media. The chemical nature of the outermost layer of these brushes was studied by water contact angle measurements. The effect of the experimental conditions (solvent, temperature, initiator concentration) on the surface properties of the polymer brushes was also investigated. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 769–782, 2006     

High‐Density Liquid‐Crystalline Polymer Brushes Formed by Surface Segregation and Self‐Assembly

High‐density polymer brushes on substrates exhibit unique properties and functions stemming from the extended conformations due to the surface constraint. To date, such chain organizations have been mostly attained by synthetic strategies of surface‐initiated living polymerization. We show herein a new method to prepare a high‐density polymer brush architecture using surface segregation and self‐assembly of diblock copolymers containing a side‐chain liquid‐crystalline polymer (SCLCP). The surface segregation is attained from a film of an amorphous base polymer (polystyrene, PS) containing a minor amount of a SCLCP‐PS diblock copolymer upon annealing above the glass‐transition temperature. The polystyrene portion of the diblock copolymer can work as a laterally mobile anchor for the favorable self‐assembly on the polystyrene base film.     

Stimuli‐responsive diblock copolymer brushes via combination of “click chemistry” and living radical polymerization

pH‐ and temperature‐responsive poly(N‐isopropylacrylamide‐block?4‐vinylbenzoic acid) (poly(NIPAAm‐b‐VBA)) diblock copolymer brushes on silicon wafers have been successfully prepared by combining click reaction, single‐electron transfer‐living radical polymerization (SET‐LRP), and reversible addition‐fragmentation chain‐transfer (RAFT) polymerization. Azide‐terminated poly(NIPAAm) brushes were obtained by SET‐LRP followed by reaction with sodium azide. A click reaction was utilized to exchange the azide end group of a poly(NIPAAm) brushes to form a surface‐immobilized macro‐RAFT agent, which was successfully chain extended via RAFT polymerization to produce poly(NIPAAm‐b‐VBA) brushes. The addition of sacrificial initiator and/or chain‐transfer agent permitted the formation of well‐defined diblock copolymer brushes and free polymer chains in solution. The free polymer chains were isolated and used to estimate the molecular weights and polydispersity index of chains attached to the surface. Ellipsometry, contact angle measurements, grazing angle‐Fourier transform infrared spectroscopy, and X‐ray photoelectron spectroscopy were used to characterize the immobilization of initiator on the silicon wafer, poly(NIPAAm) brush formation via SET‐LRP, click reaction, and poly(NIPAAm‐b‐VBA) brush formation via RAFT polymerization. The poly(NIPAAm‐b‐VBA) brushes demonstrate stimuli‐responsive behavior with respect to pH and temperature. The swollen brush thickness of poly(NIPAAm‐b‐VBA) brush increases with increasing pH, and decreases with increasing temperature. These results can provide guidance for the design of smart materials based on copolymer brushes. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2677–2685     

Thermoreversible gelation of poly(ethylene oxide) biodegradable polyester block copolymers. II

Poly(ethylene oxide)-b-poly(L-lactic acid) (PEO-PLLA) diblock copolymers were synthesized via a ring opening polymerization from poly(ethylene oxide) and l -lactide. Stannous octoate was used as a catalyst in a solution polymerization with toluene as the solvent. Their physicochemical properties were investigated by using infrared spectroscopy, ¹H-NMR spectroscopy, gel permeation chromatography, and differential scanning calorimetry, as well as the observational data of gel-sol transitions in aqueous solutions. Aqueous solutions of PEO-PLLA diblock copolymers changed from a gel phase to a sol phase with increasing temperature when their polymer concentrations are above a critical gel concentration. As the PLLA block length increased, the gel-sol transition temperature increased. For comparison, diblock copolymers of poly(ethylene oxide)-b-poly(l -lactic acid-co-glycolic acid) [PEO-P(LLA/GA)] and poly(ethylene oxide)-b-poly(dl -lactic acid-co-glycolic acid) [PEO-P(DLLA/GA)] were synthesized by the same methods, and their gel-sol transition behaviors were also investigated. The gel-sol transition properties of these diblock copolymers are influenced by the hydrophilic/hydrophobic balance of the copolymer, block length, hydrophobicity, and stereoregularity of the hydrophobic block of the copolymer. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2207–2218, 1999     

Facile synthesis and responsive behavior of PDMS‐b‐PEG diblock copolymer brushes via photoinitiated “thiol‐ene” click reaction

We present herein a mild and rapid method to create diblock copolymer brushes on a silicon surface via photoinitiated “thiol‐ene” click reaction. The silicon surface was modified with 3‐mercaptopropyltrimethoxysilane (MPTMS) self‐assembled monolayer. Then, a mixture of divinyl‐terminated polydimethylsiloxane (PDMS) and photoinitiator was spin‐coated on the MPTMS surface and exposed to UV‐light. Thereafter, a mixture of thiol‐terminated polyethylene glycol (PEG) and photoinitiator were spin‐coated on the vinyl‐terminated PDMS‐treated surface, and the sequent photopolymerization was carried out under UV‐irradiation. The MPTMS, PDMS, and PEG layers were carefully identified by X‐ray photoelectron spectroscopy, atomic force microscopy, ellipsometry, and water contact angle measurements. The thickness of the polydimethylsiloxane‐block‐poly(ethylene glycol) (PDMS‐b‐PEG) diblock copolymer brush could be controlled by the irradiation time. The responsive behavior of diblock copolymer brushes treated in different solvents was also discussed. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

A TEMPO-mediated “living” free-radical approach to ABA triblock dendritic linear hybrid copolymers

Dumbbell-shaped ABA triblock copolymers composed of benzyl ether dendrons and polystyrene as the A and B blocks, respectively, were prepared using 2,2,6,6-tetramethylpiperidinyl-1-oxy (TEMPO) -mediated “living” free-radical polymerization. A new bis-dendritic unimolecular initiator, compound 3, was employed to study the efficiency of ABA triblock formation under standard TEMPO-mediated polymerization conditions. By this design, the central B block of the ABA triblock copolymer was grown into the bis-dendritic unimolecular initiator. The ABA triblock copolymer products were separated from their by-products, AB diblock copolymers, by column chromatography on silica gel. The isolated copolymers were characterized using gel permeation chromatography and proton nuclear magnetic resonance spectroscopy as complimentary techniques. That the dendritic-linear AB diblock copolymer was obtained in a mixture with ABA triblock material indicates that TEMPO-terminated dendron counter-radical 5 is an imperfect mediator of this free-radical polymerization. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3748–3755, 1999     

Low temperature splinting activity and catalytic behavior of nano Ag doped sulphamicacid bridged diblock copolymer

A novel silver nanoparticle doped diblock copolymer was synthesized by a 3‐step process via bulk polymerization process under nitrogen atmosphere. The above prepared polymer is characterized by FTIR spectroscopy, fluorescence emission spectroscopy, circular dichroism (CD), HRTEM, and FESEM. The sulphamicacid end capped poly(ε‐caprolactone) (P1) system exhibited higher tensile strength than the sulphamicacid bridged diblock copolymer (P2) and nano Ag doped sulphamicacid bridged diblock copolymer (P3) systems. The splinting activity of the diblock copolymers was tested and confirmed the low temperature splinting activity of the diblock copolymer. The Ag nanoparticle catalyzed catalytic reduction of p‐nitrophenol (NiP) was tested, and the apparent rate constant (k_app) was determined as 7.36 × 10⁻³ sec⁻¹. The thermal studies were carried out by DSC and TGA methods. The TGA study declared that the P1 system has higher degradation temperature than the P2 and P3 systems. The P1 system has higher melting temperature (T_m) (75.5°C) than the P2 and P3 systems. The CD study indicated that the conformation of sulphamicacid was not changed even after the formation of nano Ag doped sulphamicacid bridged diblock copolymer.     

Preparation and characterization of MPEG–PCL diblock copolymers with thermo‐responsive sol–gel–sol phase transition

MPEG–PCL diblock copolymers consisting of methoxy polyethylene glycol (MPEG, 750 g/mol) and poly(?‐caprolactone) (PCL) were synthesized by ring‐opening polymerization. Aqueous solutions of the synthesized diblock copolymers were prepared by dissolving the MPEG–PCL diblock copolymers at concentrations in the range of 0–20 wt %. When the PCL molecular weight was 3000 or greater, the polymer was only partially soluble in water. As the temperature was increased from room temperature, the diblock copolymer solutions showed two phase transitions: a sol‐to‐gel transition and a gel‐to‐sol transition. The sol‐to‐gel phase transition temperature decreased substantially with increasing PCL length. The sol–gel–sol transition with the increase in temperature was confirmed by monitoring the viscosity as a function of temperature. The temperature ranges of the phase transitions measured by the tilting method were in full agreement with those determined from the viscosity measurements. The maximum viscosity of the copolymer solution increased with increasing hydrophobicity of the diblock copolymer and with increasing copolymer concentration. X‐ray diffraction (XRD) and differential scanning calorimetry (DSC) analyses revealed that the diblock copolymers exhibited crystalline domains that favored the formation of an aggregated gel because of the tight aggregation and strong packing interactions between PCL blocks. Scanning electron micrographs of the diblock copolymer solutions in the sol state showed interconnected polyhedral pore structures, whereas those of the gel state revealed a fibrillar‐like morphology. Atomic force microscope (AFM) studies of the sol and gel surfaces showed that the sol surface was covered with fine globular particles, whereas the gel surface was covered with particles in micron‐scale irregular islets. These findings are consistent with uniform mixing of the diblock copolymer and water in the sol state, and aggregation of PCL blocks in the gel state. In conclusion, we confirm that the MPEG–PCL diblock copolymer solution exhibited a sol–gel–sol transition as a function of temperature. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5413–5423, 2006     

Novel superhydrophobic silica/poly(siloxane‐fluoroacrylate) hybrid nanoparticles prepared via two‐step surface‐initiated ATRP: Synthesis,characterization, and wettability

Poly(siloxane‐fluoroacrylate)‐grafted silica hybrid nanoparticles were prepared by surface‐initiated atom transfer radical polymerization (SI‐ATRP). The silica nanoparticles with α‐bromo‐ester initiator group for copper‐mediated ATRP were prepared by the self‐assembled monolayers of (3‐aminopropyl)triethoxysilane and 2‐bromoisobutyrate bromide. Well‐defined diblock copolymer brushes consisting of poly(methacryloxypropyltrimethoxysilane) and poly(2,2,3,3,4,4,4‐heptafluorobutyl methacrylate) blocks were obtained by using initial homopolymer brushes as the macroinitiators for the SI‐ATRP of the second monomer. Chemical compositions and structures of the nanoparticles were characterized by Fourier transform infrared spectroscopy, proton nuclear magnetic resonance spectroscopy, and gel permeation chromatography. Surface properties and morphology of the nanoparticles were investigated with X‐ray photoelectron spectroscopy, scanning electron microscopy, atomic force microscopy, and water contact angle measurement. It is revealed that the surfaces of the nanocomposites are rough at the microscale and nanoscale. The formation reason of the superhydrophobic surfaces was also discussed in this work. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Control of surface properties using fluorinated polymer brushes produced by surface-initiated controlled radical polymerization

Surface-grafted styrene-based homopolymer and diblock copolymer brushes bearing semifluorinated alkyl side groups were synthesized by nitroxide-mediated controlled radical polymerization on planar silicon oxide surfaces. The polymer brushes were characterized by X-ray photoelectron spectroscopy (XPS), near-edge X-ray absorption fine structure (NEXAFS), and time-dependent water contact angle measurements. Angle-resolved XPS studies and water contact angle measurements showed that, in the case of the diblock copolymer brushes, the second block to be added was always exposed at the polymer-air interface regardless of its surface energy. Values of z*/Rg were estimated based on the radius of gyration, Rg, of the grafted homopolymer or block copolymer chains for the grafted brushes and thickness of the brush, z*. The fact that z*/Rg > 1 suggests that all these brushes are stretched. These results support the idea that after grafting the first block onto the surface the nitroxide-end capped polymer chains were able to polymerize the second block in a "living" fashion and the stretched brush so formed was dense enough that the outermost block in all cases completely covers the surface. NEXAFS analysis showed a relationship between the surface orientation of the fluorinated side chains and brush thickness with thicker brushes having more oriented side chains. Time-dependent water contact angle measurements revealed that the orientation of the side chains of the brush improved the surface stability toward reconstruction upon prolonged exposure to water.     

Side-chain-grafted random copolymer brushes as neutral surfaces for controlling the orientation of block copolymer microdomains in thin films

Random copolymers of P(S-r-MMA-r-HEMA)s with a distribution of surface reactive hydroxyl groups were synthesized to formulate neutral surface layers on a SiO2 substrate. The layers were designed to drive vertical orientation of lamellar microdomains in a top P(S-b-MMA) thin film. Copolymers with a styrene weight fraction (f(St)) of 0.58 and a HEMA fraction (f(HEMA)) ranging from 0.01 to 0.03, with a corresponding MMA fraction (f(MMA)) ranging from 0.41 to 0.39, in the P(S-r-MMA-r-HEMA) copolymer showed neutral surface characteristics. The morphology of block copolymer thin films was studied by scanning electron microscopy (SEM). P(S-r-MMA-r-HEMA) copolymers prepared by both living and classical free-radical polymerizations were equally effective in demonstrating the neutrality of the surface. These side-chain-grafted random copolymer brushes showed faster grafting kinetics than the end-chain-grafted P(S-r-MMA) because of multipoint attachment to the surface. The modified surfaces had a very thin layer of random copolymer brush (5-7 nm), which is desirable for effective pattern transfer. Furthermore, neutral surfaces could be obtained even when the grafting time was reduced to 3 h. These results indicate that the composition of the random copolymer brush, rather than its PDI or molecular weights, is the most important factor in controlling the neutrality of the surface. These results also demonstrate the feasibility of using a third comonomer (C) in the random copolymer brush P(A-r-B-r-C) to alter the interfacial and surface energies of a diblock copolymer (A-b-B).     

聚乙烯-聚异戊二烯两嵌段共聚物的合成和表征

以正丁基锂为引发剂,阴离子聚合合成了聚丁二烯-聚异戊二烯两嵌段共聚物,然后以2-乙基己酸钴/三乙基铝配位络合催化体系,将其中丁二烯段进行选择性氢化,制备了聚乙烯-聚异戊二烯两嵌段共聚物.对这两种嵌段产物分别用红外光谱、GPC,粘度法、DSC、X-射线衍射和动态力学谱等方法进行了表征.     

Surface-initiated Atom-transfer Radical Polymerization from Polyimide Films and Their Anti-fouling Properties

A simple one-step method for the chloromethylation of polyimide (PI) under mild conditions was used to introduce benzyl chloride groups into PI film surface. Covalently tethered hydrophilic polymer brushes of poly(ethylene glycol) monomethacrylate (PEGMA) and glycidyl methacrylate (GMA) were prepared via surface initiated atom-transfer radical polymerization (ATRP) from the chloromethylated PI surfaces using benzyl chloride groups as the active ATRP initiators. A kinetics study indicated that the chain growth from the films was in agreement with a controlled process. The dormant chain ends of the grafted polymer on the PI films could reinitiate the consecutive surface-initiated ATRP to prepare surface-functionalized diblock copolymer brushes on the PI films. The modified surface was characterized by X-ray photoelectron spectroscopy (XPS) after each modification stage. Protein adsorption experiments indicated that the PI-P(PEGMA) membrane exhibited substantially improved anti-fouling properties compared to the pristine PI surface.     

ATRP法合成两亲的含氟柱状刷PBIEM-g-(PAA-b-PFA)

以聚甲基丙烯酸[2-(2-溴异丁酰氧)]乙酯(PBIEM)为大分子引发剂,采用接出(grafting from)原子转移自由基聚合(ATRP)技术合成了以聚丙烯酸叔丁酯-b-聚含氟丙烯酸酯为侧链的柱状分子刷PBIEM-g-(PtBA-b-PFA).通过GPC,1H-NMR和FTIR对PBIEM-g-(PtBA-b-PFA)组成和结构进行了表征,证实ATRP过程中没有发生分子间或分子内偶合反应,制备得到可控性好的含氟嵌段共聚物刷.利用大分子链中叔丁酯基团的水解反应生成两亲的含氟柱状刷PBIEM-g-(PAA-b-PFA),原子力显微镜可直接观察到PBIEM-g-(PAA-b-PFA)特征的核壳型柱状结构,得到聚合物刷的整体长度为ln=54~72 nm.     

Non-surface activity and micellization of ionic amphiphilic diblock copolymers in water. Hydrophobic chain length dependence and salt effect on surface activity and the critical micelle concentration

We reported previously (Macromolecules 2003, 36, 5321; Langmuir, 2004, 20, 7412) that amphiphilic diblock copolymers having polyelectrolytes as a hydrophilic segment show almost no surface activity but form micelles in water. In this study, to further investigate this curious and novel phenomenon in surface and interface science, we synthesized another water-soluble ionic amphiphilic diblock copolymer poly(hydrogenated isoprene)-b-sodium poly(styrenesulfonate) PIp-h2-b-PSSNa by living anionic polymerization. Several diblock copolymers with different hydrophobic chain lengths were synthesized and the adsorption behavior at the air/water interface was investigated using surface tension measurement and X-ray reflectivity. A dye-solubilization experiment was carried out to detect the micelle formation. We found that the polymers used in this study also formed micelles above a certain polymer concentration (cmc) without adsorption at the air-water interface under a no-salt condition. Hence, we further confirmed that this phenomenon is universal for amphiphilic ionic block copolymer although it is hard to believe from current surface and interface science. For polymers with long hydrophobic chains (more than three times in length to hydrophilic chain), and at a high salt concentration, a slight adsorption of polymer was observed at the air-water interface. Long hydrophobic chain polymers showed behavior "normal" for low molecular weight ionic surfactants with increasing salt concentration. Hence, the origin of this curious phenomenon might be the macroionic nature of the hydrophilic part. Dynamic light scattering analysis revealed that the hydrodynamic radius of the block copolymer micelle was not largely affected by the addition of salt. The hydrophobic chain length-cmc relationship was found to be unusual; some kind of transition point was found. Furthermore, very interestingly, the cmc of the block copolymer did not decrease with the increase in salt concentration, which is in clear contrast to the fact that cmc of usual ionic small surfactants decreases with increasing salt concentration (Corrin-Harkins law). These behaviors are thought to be the special, but universal, characteristics of ionic amphiphilic diblock copolymers, and the key factor is thought to be a balance between the repulsive force from the water surface by the image charge effect and the hydrophobic adsorption.     

Preparation of PTBA‐PAA‐PMMA Compatibilizer for PET‐PMMA Blends by Atom Transfer Radical Polymerization

The synthesis of diblock copolymer of tert butyl acrylate and methyl methacrylate (PTBA‐b‐PMMA) was prepared by Atom Transfer Radical Polymerization (ATRP). At the outset, macroinitiator of tert butyl acrylate (TBA) was prepared by using N,N,N′,N″,N″‐pentamethyldiethylenetriamine (PMDETA) ligand, Cuprous Bromide (CuBr) catalyst, and ethyl 2‐bromo isobutyrate (2‐EiBBr) initiator. Immediately after the intake of the utmost TBA in the macroinitiator, the second monomer, methyl methacrylate (MMA) was added to the reaction medium, for further polymerization. In these experiments the compositions of the monomers were varied, although the concentrations of ligand, catalyst and the initiator were kept constant. Subsequently, the diblock copolymers were hydrolyzed, under acidic conditions, using HCl catalyst, to obtain an amphiphilic copolymer. These block copolymers were characterized by NMR, IR, GPC, and DSC techniques. These copolymers will be used in, powder coatings, pigment dispersions, and as compatibilizers in polymer blends.     

PtBMA-b-P4VP的ATRP合成及其化学转变

以α-氯代丙酸乙酯(ECP)为引发剂,N,N,N′,N″,N″-五甲基二亚乙基三胺(PMDE-TA)为配体,在N,N′-二甲基甲酰胺(DMF)溶液中引发甲基丙烯酸叔丁酯(tBMA)进行原子转移自由基聚合(ATRP),调节聚合反应时间得到了端基为氯原子,数均分子量为1.8×103~6.4×103的聚甲基丙烯酸叔丁酯(PtBMA-Cl)大分子引发剂。采用合成的5,5,7,12,12,14-六甲基-1,4,8,11-四氮杂环化合物(Me6[14]aneN4)为配体,使PtBMA-Cl引发4-乙烯吡啶(4VP)进行ATRP反应,得到了PtBMA-b-P4VP两嵌段共聚物,可使P4VP的收率达到60%。通过对PtBMA-b-P4VP的不同链段进行季铵化和水解反应,得到了聚甲基丙烯酸-b-季铵化聚4-乙烯吡啶(PMAA-b-QPVPB)亲水性嵌段共聚物。傅里叶变换红外光谱(FT-IR)、核磁共振(1H-NMR)和凝胶渗透色谱(GPC)分析表明:所得嵌段共聚物的结构明确,可将PtBMA与P4VP的链段长度之比调整在1∶0.5~1∶1的范围内。     

Diblock copolymer micellar lithography: 1. Intermicellar interactions and pathways for control of monomicellar film structure

The formation of reverse micelles of amphiphilic diblock copolymers of styrene and 2-vinylpyridine in selective (for one of the blocks) solvent (toluene) is studied by dynamic light scattering and atomic force and transmission electron microscopies, as well as by absorption spectroscopy and X-ray photoelectron spectroscopy techniques. It is revealed that the behavior of micelles of block copolymers with different ratios of block lengths and absolute molecular masses in solution is fundamentally different depending on the amount of added metal salt. The possibility of controlled variations in the characteristic sizes of two-dimensional ordered ensembles of micelles on the surface of silicon wafers is demonstrated. It is shown that, in some cases, the distance between the centers of micelles in ensemble depends on the concentration of copolymer solution and the amount of metal salt preliminarily added to the solution.