TiO<Subscript>2</Subscript> photocatalytic oxidation: I. Photocatalysts for liquid-phase and gas-phase processes and the photocatalytic degradation of chemical warfare agent simulants in a liquid phase

The results of studies on the effect of the preparation procedure on the properties of TiO₂-based photocatalysts and the kinetics and mechanism of the photocatalytic oxidation of organic water pollutants are surveyed. The effects of calcination temperature, surface modification with platinum, and acid-base treatment of the surface of titanium dioxide on its activity in model gas-phase and liquid-phase reactions are considered. Optimal catalyst preparation conditions were found in order to achieve maximum activity, and conceivable reasons for the effects of the above factors on the activity were revealed. The intermediate products and mechanisms of the photocatalytic and dark reactions of solutes that simulated chemical warfare agents in water are considered. All of the test simulants can undergo complete oxidation to form inorganic products in an aqueous TiO₂ suspension under irradiation with UV light. It was found that, in addition to oxidation, the dark steps of hydrolysis also play an important role in the degradation of these substances. The low-frequency ultrasonic treatment (20 kHz) of a photocatalyst suspension in the course of the photocatalytic oxidation of dimethyl methylphosphonate can accelerate the reaction because of the facilitated transport of reactants to the surface of photocatalyst particles.__________Translated from Kinetika i Kataliz, Vol. 46, No. 2, 2005, pp. 203–218.Original Russian Text Copyright © 2005 by Vorontsov, Kozlov, Smirniotis, Parmon.     

TiO<Subscript>2</Subscript> Photocatalytic Oxidation: III. Gas-Phase Reactors

A number of reactor designs for photocatalytic oxidation in the gas phase are considered: cylindrical reactors with photocatalysts supported by various techniques, a reactor with a vibrationally fluidized bed of a photocatalyst, and a coil reactor with the reactivation of a photocatalyst at regular intervals. It was found that the vibrational fluidization of catalyst grains enhanced catalyst activity because of the effect of periodic illumination of different grain sides. The results of testing of two types of domestic photocatalytic air purifiers commercially manufactured in Russia are reported.__________Translated from Kinetika i Kataliz, Vol. 46, No. 3, 2005, pp. 466–473.Original Russian Text Copyright © 2005 by Vorontsov, Kozlov, Smirniotis, Parmon.     

Development of TiO<Subscript>2</Subscript> photocatalysts suitable for practical use and their applications in environmental cleanup

Recently, environmental disruption is proceeding on a global scale through the consumption of huge amounts of fossil fuels and the emission of various chemical substances. However, these substances resist bio-treatment. TiO₂ generates electrons and holes by irradiation with light. Most organic micro-pollutants, including dioxins, are decomposed into carbon dioxide and water by the effect of the holes with high oxidative potential. By using such a photocatalytic reaction, various applications are feasible for environmental cleanup. In general, TiO₂ powder has been utilized as photocatalyst, although TiO₂ powder photocatalyst has several disadvantages: (1) it is difficult to handle, (2) photocatalytic reaction is slow and it takes a lot of time for treatment and (3) it is difficult to apply to plastics and textiles, because the photocatalyst decomposes them. We have developed a photocatalyst suitable for practical use and have developed high-activity photocatalysts such as TiO₂ photocatalytic transparent film, photocatalytic silica-gel, apatite-coated TiO₂ photocatalyst usable for plastics and textiles, photocatalytic paper, photocatalytic blue charcoal and photocatalytic oxygen scavenger. The application of these high-activity photocatalysts has been studied in deodorization, anti-bacterial, self-cleaning, anti-stain, water treatment, air purification such as photocatalytic decomposition of dioxins and VOC, and NO _x removal. Now various photocatalytic articles using these new photocatalyst materials are on the market in Japan. Photocatalytic technology can create many valuable products for environmental use all over the world.     

Preparation and characterization of highly photoactive nanocrystalline TiO<Subscript>2</Subscript> powders by solvent evaporationinduced crystallization method

Highly photoactive bi-phase nanocrystalline TiO₂ photocatalyst was prepared by a solvent evaporation-induced crystallization (SEIC) method, and calcined at different temperatures. The obtained TiO₂ photocatalyst was characterized with X-ray diffraction (XRD), transmission electron microscopy (TEM) and BET surface areas. The photocatalytic activity was evaluated by the photocatalytic oxidation of acetone in air. The results show that solvent evaporation can promote the crystallization and phase transformation of TiO₂ at 100°C. When calcination temperatures are below 600°C, the prepared TiO₂ powders show bimodal pore size distributions in the mesoporous region. At 700°C, the pore size distributions exhibit monomodal distribution of the inter-aggregated pores due to the collapse of the intra-aggregated pores. At 100°C, the obtained TiO₂ photocatalyst by this method shows good photocatalytic activity, and at 400°C, its photocatalytic activity exceeds that of Degussa P25. This may be attributed to the fact that the prepared TiO₂ photocatalyst has higher specific surface areas, smaller crystallite size and bimodal pore size distribution.     

Selective solar photocatalytic oxidation of ethylbenzene on C,N, and S doped TiO<Subscript>2</Subscript>

The liquid-phase photo-oxidation of ethylbenzene (EB) is investigated in solar light with air/O₂/N₂ at atmospheric pressure, in a batch reactor using acetonitrile medium. It is carried out over TiO₂ doped with C, N, and S (TCNS) photocatalyst samples. The photocatalytic oxidation yielded acetophenone (33%) and 1-phenylethanol (21%) at 56% conversion of EB during a 6-h irradiation time. This product distribution indicates that C–H bond activation has occurred only at the alkyl chain. The effects of the EB to water content ratio, amount of photocatalyst and its sustainability, pH, have been studied. It is illustrated that the reaction carried out by this environmentally friendly photocatalysis is truly heterogeneous under mild conditions using solar light and no waste generation. An optimum loading of TCNS5 was observed for the photo-oxidation of EB.     

Preparation of TiO<Subscript>2</Subscript> nanofibers immobilized on quartz substrate by electrospinning for photocatalytic degradation of ranitidine

The photocatalytic activity of TiO₂ nanofibers immobilized on quartz substrates was investigated by evaluating the decomposition of organic pollutants. TiO₂ nanofibers were synthesized by electrospinning the Ti-precursor/polymer mixture solution, followed by hot-pressing for enhancing the adhesion of TiO₂-nanofiber films to the substrates. TiO₂ started to crystalize in the anatase form at 500 °C and reached the optimal photocatalytic anatase/rutile phase ratio of 70:30 at a calcination temperature of 600 °C. The TiO₂-nanofiber film was demonstrated to be an efficient photocatalyst by ranitidine decomposition under UV illumination and was proven to have a comparable photocatalytic activity with the well-known Degussa P25 nanoparticulate photocatalyst and excellent recyclability during 10 cycles of photocatalytic operation, indicating no loss of TiO₂ nanofibers during photocatalytic operations.     

AgBr@TiO<Subscript>2</Subscript>/GO ternary composites with enhanced photocatalytic activity for oxidation of benzyl alcohol to benzaldehyde

AgBr@TiO₂/GO (graphene oxide) ternary composite photocatalyst was synthesized by fabricating core–shell-structured AgBr@TiO₂ and anchoring it onto the surface of GO. The obtained samples were characterized by transmission electron microscopy, X-ray diffraction analysis, X-ray photoelectron spectroscopy, ultraviolet–visible (UV–Vis) diffuse reflectance spectrum, and photoluminescence (PL) spectroscopy. It was found that the AgBr nanoparticles were prone to aggregation while the core–shell-structured AgBr@TiO₂ possessed excellent dispersity. PL analysis revealed that the ternary-structured AgBr@TiO₂/GO could effectively promote the separation rate of electron–hole pairs. Photocatalytic oxidation of benzyl alcohol to benzaldehyde under visible-light irradiation was selected as probe reaction to evaluate the photocatalytic activity of the different samples. It was found that the AgBr@TiO₂/GO ternary composite exhibited evidently improved photocatalytic activity compared with AgBr, AgBr@TiO₂, and AgBr/GO. On the basis of the experiment results, the photocatalytic oxidation mechanism of benzyl alcohol over AgBr@TiO₂/GO is tentatively discussed.     

水蒸气对有机污染物微波光催化氧化反应的影响

 以C2H4和C2HCl3为模型有机污染物,考察了不同反应条件下水蒸\r\n气对微波催化反应性能的影响．结果表明,水蒸气的存在是影响微波光\r\n催化反应性能的重要因素．由于微波对物质的极化作用不同,在加水的\r\n微波光催化反应过程中微波能量主要被水吸收,微波场对水的脱附有利\r\n于提高加水条件下C2H4微波光催化氧化活性,但不利于需要水的C2HCl\r\n3氧化反应的进行．     

Structural characterization and photocatalytic properties of novel Bi<Subscript>2</Subscript>FeVO<Subscript>7</Subscript>

Bi₂FeVO₇ was prepared by a solid-state reaction technique for the first time and the structural and photocatalytic properties of Bi₂FeVO₇ were studied. The results shows that this compound crystallized in the tetragonal crystal system with space group I4/mmm. Moreover, the band gap of Bi₂FeVO₇ was estimated to be about 2.22(6) eV. For the photocatalytic water splitting reaction, H₂ or O₂ evolution was observed from pure water with Bi₂FeVO₇ as the photocatalyst by ultraviolet light irradiation. Degradation of aqueous methylene blue (MB) dye by photocatalytic way over this compound was further studied under visible light irradiation. Bi₂FeVO₇ shows higher catalytic activity compared to TiO₂ (P-25) for MB photocatalytic degradation under visible light irradiation. Complete removal of aqueous MB was realized after visible light irradiation for 170 min with Bi₂FeVO₇ as the photocatalyst. The reduction of the total organic carbon (TOC) and the formation of inorganic products, SO ₄ ²⁻ and NO ₃ ⁻ revealed the continuous mineralization of aqueous MB during the photocatalytic course.     

Possibility of using an UV–nano-TiO<Subscript>2</Subscript>–K<Subscript>2</Subscript>Cr<Subscript>2</Subscript>O<Subscript>7</Subscript> system for the determination of COD

The results of a study of the optimum oxidation conditions in the system UV?nano-Т?О₂–K₂Cr₂O₇ in a specially designed photoreactor are presented. The basic parameters of the photocatalytic oxidation of glucose and acetic acid were studied and optimized. The oxidation of organic compounds under the optimized conditions was studied. Nano-TiO₂ was shown to be a promising photocatalyst in the design of new oxidation systems for analytical purposes.     

Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>/BiFeO<Subscript>3</Subscript> heterostructure: preparation,characterization, and photocatalytic activity

Bi₂O₃/BiFeO₃ composite was successfully fabricated by a conventional sol–gel method and structural properties were characterized based on X-ray diffractometer, scanning electron microscope, transmission electron microscope, energy-dispersive X-ray analyzer, nitrogen adsorption–desorption measurement, and UV–visible diffuse reflectance spectroscopy. Bi₂O₃/BiFeO₃ had a good absorption for visible light, which was benefit to photocatalytic activity. The highest degradation efficiency was obtained when the content of Bi₂O₃ in Bi₂O₃/BiFeO₃ was 63.9%. Effect of experimental conditions was investigated, and the highest photocatalytic activity of Bi₂O₃/BiFeO₃ was observed at photocatalyst dosage of 0.5 g/L, initial BPA concentration of 10 mg/L, and solution pH of 6.3. Bi₂O₃/BiFeO₃ photocatalyst exhibited enhanced photocatalytic activity for BPA, and the reaction rate constant over Bi₂O₃/BiFeO₃ composite was 2.23, 3.65, and 8.71 times higher than that of BiFeO₃, Bi₂O₃ and commercial TiO₂ (P25), respectively. Bi₂O₃/BiFeO₃ showed high photocatalytic activity after three cycles, suggesting that it was a stable photocatalyst. The possible photocatalytic mechanism has been discussed on the basis of the theoretical calculation and the experimental results. The hydroxyl and superoxide radicals together with photogenerated holes played significant roles in the photocatalytic reaction.     

Catalytic Properties of TiO<Subscript>2</Subscript>/Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> Nanoparticles in Plasma Chemical Treatment

We proposed here a new process coupling dielectric barrier discharge (DBD) plasma with magnetic photocatalytic material nanoparticles for improving yield in DBD degradation of methyl orange (MO). TiO₂ doped Fe₃O₄ (TiO₂/Fe₃O₄) was prepared by the sol-gel method and used as a new type of magnetic photocatalyst in DBD system. It was found that the introduction of TiO₂/Fe₃O₄ in DBD system could effectively make use of the energy generated in DBD process and improve hydroxyl radical contributed by the main surface Fenton reaction, photocatalytic reaction and catalytic decomposition of dissolved ozone. Most part of MO (88%) was degraded during 30 min at peak voltage of 13 kV and TiO₂/Fe₃O₄ load of 100 mg/L, with a rate constant of 0.0731 min^?1 and a degradation yield of 7.23 g/(kW h). The coupled system showed higher degradation efficiency for MO removal.     

Photocatalytic activity of visible light-responsive TiO<Subscript>2</Subscript> thin films deposited on various anodized Ti-metal substrates by a RF magnetron sputtering method

Visible light-responsive TiO₂ (Vis-TiO₂) thin film has been deposited on two different kinds of anodized Ti-metal substrates, i.e., plate-type Titanystar (P-Titanystar) or non-woven fabric Titanystar (N-Titanystar) by a radio-frequency magnetron sputtering (RF-MS) method. These Vis-TiO₂ thin film photocatalysts (Vis-TiO₂/P-Titanystar and Vis-TiO₂/N-Titanystar) showed high activity for the oxidation of 2-propanol in water under UV light irradiation while Vis-TiO₂/N-Titanystar showed higher activity than Vis-TiO₂/P-Titanystar. Furthermore, photocatalytic activity of Vis-TiO₂/N-Titanystar was enhanced by the Pt deposition by an RF-MS deposition method. Pt loaded Vis-TiO₂/N-Titanystar (Pt-Vis-TiO₂/N-Titanystar) acted as an efficient photocatalyst for the oxidation of methanol vapor under UV light irradiation even in a flow system. Moreover, it was found that Pt-Vis-TiO₂/N-Titanystar is an effective photocatalyst for the oxidation of various organic compounds in gas phase or ammonia gas even under visible light irradiation (λ > 420 nm) at 293 K.     

Kinetic studies of direct blue photodegradation over flower-like TiO<Subscript>2</Subscript>

The kinetics of photocatalytic oxidation reaction for direct blue solution was studied by using flower-like TiO₂ under the irradiation of ultraviolet (UV) light. A series of possible affecting factors were studied, including pH value, the additive amount of light catalyst, H₂O₂ and with or without Ag modification. The kinetics of photocatalytic degradation under UV was found following a pseudo-second-order reaction kinetic model with high regression coefficients (R ²). It has been demonstrated that the initial concentration and its related factors have influenced the photocatalytic degradation efficiency and corresponding kinetic parameters. Also, the kinetic parameter k is increasing with the degradation efficiency.     

Photocatalysis: Light energy conversion for the oxidation,disinfection, and decomposition of water

The results of many-year studies of the relationship between the physical properties and photocatalytic activity of TiO₂ and Pt/TiO₂ in photocatalytic purification and disinfection of air and water and water photodecomposition with oxygen evolution are presented. Recommendations are given as to finding the optimal method for platinum supporting on TiO₂ to achieve the highest possible catalytic activity. Multisite kinetic models of the gas-phase oxidation of simple organic substances are considered. Methods for regenerating the photocatalyst after its deactivation in the oxidation of sulfur-containing organic substances are suggested. New data are discussed on the acceleration of air purification by the combination of photocatalytic oxidation with atmospheric electric discharges, the addition of gaseous hydrogen peroxide, and oxidation on photocatalysts existing in the aerosol state. As compared to pure TiO₂, platinated titanium dioxide has a higher capability for disinfection and complete mineralization of microorganisms. Two promising methods for production of hydrogen from water using solar light are presented.     

Modification of the Optical and Electronic Properties of TiO<Subscript>2</Subscript> By N Anion-Doping for Augmentation of the Visible Light Assisted Photocatalytic Performance

In this work, a nitrogen-doped anatase TiO₂ nanocrystal is prepared by a modified sol-gel preparation method using the nonionic surfactant (polyoxyethylene sorbitan monooleate) as a structural controller and a soft template. The as-prepared samples are characterized by X-ray diffraction, Raman spectroscopy, UVVis diffuse reflectance spectroscopy, and X-ray photoelectron spectroscopy techniques. Then the photocatalytic activity of these samples is assessed by the photocatalytic oxidation of phenol under visible light irradiation. The phenol concentration is measured using a UV-Vis spectrometer. Experimental results show that N-doping leads to an excellent visible light photocatalytic activity of the TiO₂ nanocatalyst. Furthermore, the formation energy and electronic structure of pure and N-doped anatase TiO₂ are described by density functional theory (DFT) calculations. It is found that N-doping narrowed the band gap of bare TiO₂, which leads to an excellent visible light photocatalytic activity of N–TiO₂ nanocatalysts. Therefore, the prepared N–TiO₂ photocatalyst is expected to find the use in organic pollutant degradation under solar light illumination.     

Synthesis,characterization and photocatalytic properties of tungsten-doped hydrothermal TiO<Subscript>2</Subscript>

Crystalline anatase phase TiO₂ with photocatalytic properties was obtained through a sol–gel low-temperature hydrothermal process. TiO₂ samples doped with tungsten oxide were also obtained by using this synthetic approach. The photocatalytic oxidation of methylene blue in water was monitored to study the influence of the tungsten doping degree on the photocatalytic degradation performance of TiO₂. The degradation rate constant was further increased by adjusting the tungsten doping degree of hydrothermal TiO₂. Also, a much faster photodegradation of methylene blue was achieved using tungsten doped samples baked at 450°C. The results were compared with those obtained with Degussa P25 used as photocatalyst. The structure and optical properties of tungsten-doped TiO₂ were studied by SEM, X-ray diffraction, UV–vis and DRIFT spectroscopy techniques.     

Influence of MnO<Subscript>2</Subscript> on the photocatalytic activity of P-25 TiO<Subscript>2</Subscript> in the degradation of methyl orange

Influences of α-MnO₂, β-MnO₂, and δ-MnO₂ on the photocatalytic activity of Degussa P-25 TiO₂ have been investigated through the photocatalytic degradation of methyl orange. The TiO₂ photocatalyst, before and after being contaminated by MnO₂, was characterized by UV-visible diffuse reflectance spectroscopy (UV-vis DRS), photoluminescence (PL), and X-ray photoelectron spectroscopy (XPS). The results showed that photocatalytic activity of TiO₂ could be inhibited significantly or completely deactivated due to the presence of even a small amount of MnO₂ particles. It was found that the poisoning effect varied with the crystal phases of MnO₂ and the effect was in the order δ-MnO₂ >α-MnO₂ >β-MnO₂. The poisoning effect was attributed to the formation of heterojunctions between MnO₂ and TiO₂ particles. The heterojunctions changed the chemical state of Ti⁴⁺ and O²⁻ sites in the crystalline phase of TiO₂. MnO₂ in contact with TiO₂ particles also broadens the band-gap of TiO₂, which decreases UV absorption of TiO₂. It can also create some deep impurity energy levels serving as photoelectron-photohole recombination center, which accelerates the electron-hole recombination. Supported by the National Natural Science Foundation of China (Grant No. 20477009) and the Natural Science Foundation of Hebei Province (Grant No. E2005000183)     

Ionic‐Liquid‐Assisted Synthesis of Uniform Fluorinated B/C‐Codoped TiO2 Nanocrystals and Their Enhanced Visible‐Light Photocatalytic Activity

Exploiting advanced photocatalysts under visible light is of primary significance for the development of environmentally relevant photocatalytic decontamination processes. In this study, the ionic liquid (IL), 1‐butyl‐3‐methylimidazolium tetrafluoroborate, was employed for the first time as both a structure‐directing agent and a dopant for the synthesis of novel fluorinated B/C‐codoped anatase TiO₂ nanocrystals (T_IL) through hydrothermal hydrolysis of tetrabutyl titanate. These T_IL nanocrystals feature uniform crystallite and pore sizes and are stable with respect to phase transitions, crystal ripening, and pore collapse upon calcination treatment. More significantly, these nanocrystals possess abundant localized states and strong visible‐light absorption in a wide range of wavelengths. Because of synergic interactions between titania and codopants, the calcined T_IL samples exhibited high visible‐light photocatalytic activity in the presence of oxidizing Rhodamine B (RhB). In particular, 300 °C‐calcined T_IL was most photocatalytically active; its activity was much higher than that of TiO_1.98N_0.02 and reference samples (T_W) obtained under identical conditions in the absence of ionic liquid. Furthermore, the possible photocatalytic oxidation mechanism and the active species involved in the RhB degradation photocatalyzed by the T_IL samples were primarily investigated experimentally by using different scavengers. It was found that both holes and electrons, as well as their derived active species, such as ^.OH, contributed to the RhB degradation occurring on the fluorinated B/C‐codoped TiO₂ photocatalyst, in terms of both the photocatalytic reaction dynamics and the reaction pathway. The synthesis of the aforementioned novel photocatalyst and the identification of specific active species involved in the photodegradation of dyes could shed new light on the design and synthesis of semiconductor materials with enhanced photocatalytic activity towards organic pollutants.     

Visible-light-driven photocatalytic degradation of microcystin-LR by Bi-doped TiO<Subscript>2</Subscript>

Bi-doped nano-crystalline TiO₂ (Bi–TiO₂) has been synthesized by sonocrystallization at low temperature. The Bi–TiO₂ materials have narrower bandgaps than pristine TiO₂, which endow them with significant visible light absorption. Accordingly, these materials had enhanced photocatalytic activity in the degradation of organic dye pollutants and the cyanotoxin microcystin-LR (MC-LR) under visible irradiation. It was found that degradation of MC-LR is rather efficient. After irradiation with visible light for 12 h the original MC-LR was removed completely, and 78% of the organic carbon was mineralized into CO₂ after irradiation for 20 h. The hydroxyl radical (·OH) is the major active species responsible for the degradation reaction. Identified intermediates primarily originate from attack of ·OH radicals on the double bonds between C4 and C5 (C6 and C7) of Adda and the ethylenic bond of Mdha in MC-LR. Some peptide bonds are also broken with longer irradiation time.