H—ZSM—35分子筛物化性质的研究

本文考察了不同温度焙烧ＨＺＳＭ－３５分子筛吸附苯后的ＥＰＲ信号是随着焙烧温度升高而增加。分子筛Ｂ酸向Ｌ酸中心转化，在６００－７００℃温度区域内有一个突破。本文还讨论了焙烧温度对邻二甲苯异构化的催化活性的影响。     

La-HY-SBA-15催化烷基化催化剂制备

采用原位合成法制备了HY-SBA-15分子筛,并进行La改性。用XRD、N_2吸附-脱附等表征分析,在小型固定床上考察了La负载量、焙烧温度、时间对烷基化性能的影响,结果发现,最优制备条件是La负载量为10%、焙烧温度550℃、焙烧时间4.5h。XRD、N_2吸附-脱附表征分析La-HY-SBA-15分子筛有微-介孔结构,NH_3-TPD表征分析La-HY-SBA-15分子筛主要为中强酸,Py-FTIR表征分析La-HY-SBA-15分子筛L酸比B酸多。     

HZSM－5分子筛的水热脱铝研究 Ⅰ．氨－FTIR与吡啶－FTIR考察

运用ＦＴＩＲ手段，以氨和吡啶为探针研究了水热处理对分子筛结构及酸性的影响。研究结果表明，水热处理温度对分子筛中铝的状态有很大影响，随着水热处理温度的升高，骨架铝不断从分子筛的骨架中脱除出来，Ｂ酸位亦随之减少；脱出来的铝在孔道中沉积形成非骨架铝物种，其结构十分复杂，部分地形成了Ｌ酸位，从而使Ｌ酸位随着水热处理温度的升高而有所增加。Ｂ酸位与骨架铝有很好的对应关系。     

Pt／ZSM—5吸附与催化性能的研究

本文研究了氨和正已烷在Ｐｔ／ＺＳＭ－５上的吸附性能并考察了Ｐｔ含量和焙烧温度对正已烷芳构化性能的影响。结果表明，Ｐｔ含量和焙烧温度对吸附和催化性能有影响。Ｐｔ与分子筛的酸中心对芳构化均有作用。     

FT－IR和程序升温热谱技术研究Mo／HZSM－5催化剂的制备过程

采用ＦＴ－ＩＲ和程序升温热谱技术研究了Ｍｏ／ＨＺＳＭ－５催化剂的制备过程．结果表明Ｍｏ／ＨＺＳＭ－５样品在合适的温度下焙烧一定时间，Ｍｏ物种与ＨＺＳＭ－５分子筛的酸中心（主要是强酸中心）起作用，并且一部分Ｍｏ物种会迁移到分子筛孔道内．在外表面的Ｍｏ物种和在孔道内强酸中心作用的Ｍｏ物种，可能是对甲烷活化起作用的     

程序升温热脱附研究不同热处理的HZSM-5分子筛的表面酸性和催化活性

用静态程序升温热脱附方法研究了不同热处理条件对HZSM-5分子筛的酸性和催化活性时影响。测得了不同焙烧温度和不同抽空温度下氨在HZSM-5上的热脱附谱,计算了测定条件下所相应的HZSM-5的表面酸中心数。结果表明,在HZSM-5表面上存在的两种强弱不同的酸中心随热处理温度而变化的趋势是一致的。在小于650℃时,焙烧温度对异构化的活性中心的酸强度分布影响不大。不同焙烧温度的HZSM-5上邻二甲苯异构化活性与酸中心数有对应的关系,它们随焙烧温度的变化趋势颇为相似。     

焙烧对HZSM－5分子筛结构的影响

运用魔角自转固态核磁共振谱（ＭＡＳ－ＮＭＲ），研究了焙烧对ＨＺＳＭ－５分子筛结构的影响．结果表明，高温焙烧将引起ＨＺＳＭ－５分子筛骨架的脱铝，当焙烧温度从５００℃增加到７００℃时，ＨＺＳＭ－５的骨架Ｓｉ／Ａｌ比由１６．７增加至２２．７；而当焙烧温度由７００℃到８００℃时，骨架Ｓｉ／Ａｌ比则由２２．７增加到了４８．５．２７Ａｌ－ＭＡＳＮＭＲ结果表明，从骨架上脱下来的铝，部分地形成了ＮＭＲ不可见的无定形态．随着焙烧温度的升高，ＮＭＲ不可见铝增多     

影响SAPO－11分子筛焙烧前后晶胞空间群变化的因素

 从合成参数出发，详细考察了不同因素对SAPO－11分子筛焙烧前后晶胞空间群变化的影响．发现成胶方式、成胶温度、模板剂组成、晶化温度、晶化时间及分子筛产物组成均是影响分子筛晶胞空间群变化的因素．MAS－NMR分析结果表明，分子筛的微观结构决定了分子筛晶胞空间群的变化，Si（4Si）区增加，分子筛保持为Icm2空间群的趋势增强．     

SO_4~（2－）－TiO_2－Hβ－Al_2O_3催化剂的制备及催化性能研究

以Ｈβ沸石为基础，通过ＴｉＯ_２改性及硫酸铵处理制备了ＳＯ－ＴｉＯ_２－Ｈβ－Ａｌ_２Ｏ_３催化剂，并由ＸＲＤ、ＸＰＳ、ＮＨ_３－ＴＰＤ、ＦＴＩＲ及化学吸附等手段考察了不同焙烧温度对该催化剂表面性质、酸性及催化性能的影响。结果表明：适宜的焙烧温度使ＳＯ－ＴｉＯ２－Ｈβ－Ａｌ２Ｏ３的酸量大幅度增加，强酸比例增大，并产生部分增强酸中心。高强度的酸性中心中，以Ｌ酸中心为主；５５０℃焙烧的样品能使沸石表面上ＳＯ与ＴｉＯ_２间发生较强的相互作用，高温焙烧则使浓度下降；该催化剂明显促进了丙烯与异丙醇的醚化反应，丙烯转化率由８．０％增高到１５．９％。关键词     

SAPO－5，－11和－34分子筛模板剂的脱除及其结构的热致变化

用水热法合成了ＳＡＰＯ－５，－１１和－３４硅磷酸铝类分子筛。并对经不同温度焙烧处理的样品进行表征，结果表明：分子筛中模块剂的热分解过程与其结构和孔大小有较大的关系。在ＳＡＰＯ－５和ＳＡＰＯ－３４分子筛中，外部联接的Ｔ－Ｏ－Ｔ键的反对称伸缩振动峰（１２４０ｃｍ~（－１）－１０３８ｃｍ~（－１））和其对称伸缩振动（７３４ｃｍ~（－１）－６００ｃｍ~（－１））及双环的变形振动（６００－５００ｃｍ~（－１））的吸收峰对样品的结晶度比较敏感。但在ＳＡＰＯ－１１中，分子筛骨架中Ｔ－Ｏ－Ｔ反对称伸缩振动（１２２５ｃｍ~（－１）和１０３８ｃｍ~（－１））随结晶度的下降而基本保持不变，但内四面体（ＴＯ_４）的对称伸缩振动，反对称伸缩振动峰及Ｔ－Ｏ弯曲振动峰随样品焙烧温度的升高而减弱并分裂。红外吸收带向低频方向移动。ＳＥＭ－ＥＤＡＸ结果表明：随样品焙烧温度的升高，结晶度下降，分子筛晶形变得不规则，晶面越来越粗糙，但结晶度的下降并非由于其中ＰＯ_４四面体的热分解所引起，而是由外部联结的Ｔ－Ｏ－Ｔ键的断裂，双环被破坏及骨架元素间的重排所引起。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.