Surface modification and characterization of indium-tin oxide for organic light-emitting devices

In this work, we used different treatment methods (ultrasonic degreasing, hydrochloric acid treatment, and oxygen plasma) to modify the surfaces of indium-tin oxide (ITO) substrates for organic light-emitting devices. The surface properties of treated ITO substrates were studied by atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS), sheet resistance, contact angle, and surface energy measurements. Experimental results show that the ITO surface properties are closely related to the treatment methods, and the oxygen plasma is more efficient than the other treatments since it brings about smoother surfaces, lower sheet resistance, higher work function, and higher surface energy and polarity of the ITO substrate. Moreover, polymer light-emitting electrochemical cells (PLECs) with differently treated ITO substrates as device electrodes were fabricated and characterized. It is found that surface treatments of ITO substrates have a certain degree of influence upon the injection current, brightness, and efficiency, but hardly upon the turn-on voltages of current injection and light emission, which are in agreement with the measured optical energy gap of the electroluminescent polymer. The oxygen plasma treatment on the ITO substrate yields the best performance of PLECs, due to the improvement of interface formation and electrical contact of the ITO substrate with the polymer blend in the PLECs.     

Surface treatment and characterization of ITO thin films using atmospheric pressure plasma for organic light emitting diodes

Ar atmospheric pressure plasma (APP) was used to treat indium-tin-oxide (ITO). The plasma conditions were varied to treat the ITO surface, e.g., plasma treatment time, RF power, flow rate, and the plasma outlet-to-sample distance. The plasma effectiveness was measured by the contact angle. The change in the surface energy calculated with the Owens-Wendt method mainly arises from the polar component. The dynamic contact angle measurements show that APP-treated surface showed considerably lower hysteresis in the water and ethylene glycol but there was no change in hysteresis in methylene iodide compared with the untreated ITO. Atomic force microscopy showed that the Ar APP-treated surface sharply decreased the surface roughness and showed a similar morphology as the untreated ITO. X-ray photoelectron spectroscopy showed that the Ar APP treatment not only effectively removed carbon contamination from the surface but also introduced oxygen. Therefore, it is believed that the APP treatment modifies the physico-chemical properties of ITO, which can in turn improve the performance of the organic light-emitting diodes.     

Staphylococcus epidermidis adhesion to He, He/O(2) plasma treated PET films and aged materials: contributions of surface free energy and shear rate

Adhesion studies of bacteria (Staphylococcus epidermidis) to plasma modified PET films were conducted in order to determine the role of the surface free energy under static and dynamic conditions. In particular, we investigated the effect of the ageing time on the physicochemical surface properties of helium (He) and 20% of oxygen in helium (He/O₂) plasma treated polyethylene terephthalate (PET) as well as on the bacterial adhesion. Treatment conditions especially known to result in ageing sensitive hydrophilicity (hydrophobic recovery) were intentionally chosen in an effort to obtain the widest possible range of surface energy specimens and also to avoid strong changes in the morphological properties of the surface. Both plasma treatments are shown to significantly reduce bacterial adhesion in comparison to the untreated PET. However, the ageing effect and the subsequent decrease in the surface free energy of the substratum surfaces with time – especially in the case of He treated samples – seem to favor bacterial adhesion and aggregation. The dispersion-polar and the Lifshitz–van der Waals (LW) acid–base (AB) thermodynamic approaches were applied to calculate the Gibbs free energy changes of adhesion (ΔG_adh) of S. epidermidis interacting with the substrates. There was a strong correlation between the thermodynamic predictions and the measured values of bacterial adhesion, when adhesion was performed under static conditions. By decoupling the (ΔG_adh) values into their components, we observed that polar/acid–base interactions dominated the interactions of bacteria with the substrates in aqueous media. However, under flow conditions, the increase in the shear rate restricted the predictability of the thermodynamic models.     

Anode Engineering of Highly Efficient Polymer Solar Cells Using Treated ITO

ITO substrates were treated with organic solvent cleaning(OSC), SC1 treatment[V(NH₄OH):V(H₂O₂): V(H₂O)=1:1:5], O₂ plasma and UV ozone, respectively. Combined investigations of atom force microscopy(AFM), water contact angle measurements, ultraviolet photoemission spectroscopy(UPS) and X-ray photoemission spectroscopy(XPS) demonstrated that UV ozone treatment could give rise to the smoothest surface, the most hydrophilic property and the highest work function(WF) of ITO due to the removal of hydrophobic C-O impurity from the ITO surface and the enrichments of more oxygen on the ITO surface. When PEDOT:PSS film[(poly(3,4-ethylenedioxy- thiophene):poly(styrene sulfonate)] was deposited on the ITO substrates treated with UV ozone, it showed a lower root-mean- square roughness in AFM images, a higher transmission in UV-Vis transmission spectra and a higher WF in UPS spectra than the PEDOT:PSS films deposited on the ITO substrates treated by other three methods. As a result, the power conversion efficiency of polymer solar cells(PSCs) based on PTB7:PC₇₁BM as an active layer and ITO treated by UV ozone as an anode can reach 8.48% because of the simultaneously improved short circuit current, open circuit voltage and fill factor compared to the PSCs with ITO treated with other three methods.     

Stable superhydrophobic and lipophobic conjugated polymers films

With a view to developing repellent materials combining both low surface energy and rough structure, original semi-fluorinated polythiophenes have been chemically and electrochemically synthesized and characterized by cyclic voltammetry, GPC, and UV-visible measurements. Polymer films have been deposited onto different substrates by drop casting a soluble polymer fraction on glass plate or by electrodeposition on ITO plate. Surface properties and particularly water and oil repellencies have been investigated by goniometry and correlated with the surface morphology and structure observed by SEM. The incorporation of fluorocarbon chains in the rigid polythiophene backbone yields very low surface free energy materials. Moreover, the way of deposition has a huge influence on the quality and performance of the film surface properties. Electroformed polymers, due to rough surfaces, exhibit great super-hydrophobic and lipophobic properties together with exceptional time stability.     

含二氮杂萘酮结构聚醚砜酮膜的微波等离子体处理研究

含二氮杂萘酮结构型聚醚砜酮(ＰＰＥＳＫ)是近年来本研究组开发成功的新型耐高温聚合物[1].该聚合物具有优异的力学性能和突出的耐热性,玻璃化转变温度(Ｔｇ)为265～305℃(随砜酮比不同而变化),其结构式如下:ＯＮＮＯＳＯＯＯＮＮＯＣＯ　　研究表明,用ＰＰＥＳＫ制成的气体分离膜对Ｏ2/Ｎ2、ＣＯ2/Ｎ2有良好的气体渗透性和透过选择性[2,3],但由于其亲水性不高进而限制了它在纳滤膜和反渗透膜等方面的应用,因此有必要对其进行改性.目前,常用的膜及膜材料改性的方法有磺化、氯甲基化季胺化、接枝等化学改性和低温等离子体与辐射等物理改性.其…     

Influence of the substrate type on the microstructural,optical and electrical properties of sol–gel ITO films

Indium tin oxide (ITO) is recognized as the best transparent and conductive material [transparent conducting oxide (TCO)] until now and its properties are dependent on the preparation method. In the present work ITO films with In:Sn atomic ratio 9:1 were prepared by a sol–gel route on different substrates (microscope glass slides, microscope glass covered with one layer of SiO₂ and Si wafers) for TCO applications. The multilayer ITO films were obtained by successive deposition by the dip-coating method and the films were characterized from the structural, morphological, optical, and electrical points of view using X-ray diffraction, scanning electron microscopy, atomic force microscopy, spectroscopic ellipsometry and by Hall effect measurements, respectively. The results showed that the thickness, optical constants and carrier numbers depend strongly on the type of substrate, number of deposited layers and sol concentration. The optical properties of ITO films are closely related to their electrical properties. The enhancement of the conductivity was possible with the increase of crystallite size (which occurred after thermal treatment) and with the reduction of surface roughness.     

Influence of Electrical,Chemical and Morphological Properties of Inorganic/Organic Interface on Light Emitting Devices Performance

studies on the influence of chemical and physical treatments on the properties of indium–tin oxide (ITO) thin films are reported. The ITO films are utilized as transparent anodes of organic light-emitting diodes (OLEDs) incorporating poly(9,9-dihexyl-9H-fluorene-2,7-diyl) (PF6) as the hole transporter material and 8-hydroxyquinoline aluminum salt (Alq3) as emitter material. Chemical (HCl, piranha solutions), thermal (vacuum annealing), physical treatments (oxygen plasma, UV ozone) and combined treatments are studied. First, ITO layers with different treatments are characterized by using four point probe method, contact angle measurement, X-Ray diffraction (XRD), surface profilometer, scanning electron microscopy (SEM), UV-Vis-IR transmittance. Later, electrical and optical properties of OLEDs with treated ITO as anode are extensively investigated.     

Activation of PET Using an RF Atmospheric Plasma System

The plasma treatment of polymer surfaces is routinely used to enhance surface properties prior to adhesive bonding or biomolecule interaction. This study investigates the influence of plasma treatment conditions on the surface activation of polyethylene terephthalate (PET) using the SurFx Atomflo? 400L plasma source. In this study the effect of applied plasma power, processing speed, gas composition and plasma applicator nozzle to substrate distance were examined. The level of polymer surface activation was evaluated based on changes to the water contact angle (WCA) of PET samples after plasma treatment. PET surface properties were also monitored using surface energy and X-ray photoelectron spectroscopy (XPS) analysis. The heating effect of the plasma was monitored using thermal imaging and optical emission spectroscopy (OES) techniques. OES was also used as a diagnostic tool to monitor the change in atomic and molecular species intensity with changes in experimental conditions in both time and space. XPS analysis of the PET samples treated at different plasma powers indicated that increased oxygen content on samples surfaces accounted for the decreases observed in WCAs. For the first time a direct correlation was obtained between polymer WCA changes and the OES measurement of the atomic hydrogen Balmer H_α and molecular OH line emission intensities.     

Effect of oxygen plasma treatment on the release behaviors of poly(epsilon-caprolactone) microcapsules containing tocopherol

The biodegradable poly(epsilon-caprolactone) microcapsules (PCL) containing tocopherol (TC) were prepared by emulsion solvent evaporation method, and microcapsules were treated by oxygen plasma to enhance the hydrophilic microcapsules. The morphologies and thermal properties of the microcapsules were determined by SEM and DSC measurements. The microcapsules studied were characterized by surface free energy or work of adhesion through contact angle measurement. As a result, the features of the microcapsules could be adjusted by manufacturing condition, such as surfactant and core ratio. The surface free energy or work of adhesion of the microcapsules was increased with increasing the time of plasma treatment, which could be attributed to the increased hydrophilic groups during oxygen plasma treatment. The release profile of the microcapsules was determined by UV-vis spectroscopy and the microcapsules containing tocopherol showed the rapid release rate, as compared with untreated ones.     

Surface control and cryogenic durability of transparent CNT coatings on dip-coated glass substrates

Transparent carbon nanotube (CNT) coatings were deposited on boro-silicate glass substrates by dip-coating. Ultraviolet-visible (UV) spectra, surface resistance measurement, and the wettability tests were used to investigate the optical transmittance and electrical properties of these CNT coatings. The changes in electrical and optical properties of these coatings were observed to be functions of the number of dip-coating cycles. The surface resistance of the CNT coated substrates decreased dramatically as the number of dip-coatings was increased, whereas the increases in the CNT layer thickness beyond that for the first dipping cycle had little effect on the transparent-properties. Static contact angle measurements proved to be an effective means for evaluating the surface morphology of CNT coatings. The interfacial durability of the CNT coatings on a glass substrate was much better than that of ITO coatings over the temperature range from -150°C to +150°C.     

Plasma pretreatment of polycarbonate substrates for indium zinc oxide film deposition

The influence of plasma treatment of polycarbonate (PC) substrates on the morphological, electrical, and adhesion properties of deposited amorphous transparent indium zinc oxide (IZO) by direct current magnetron sputtering was investigated by analyzing atomic force microscopy, contact angles, Hall, and nano‐scratch measurements. The surfaces of PC substrates were performed by plasma treatment at various processing times in Ar/O₂ mix atmosphere. The atomic force microscopy images indicated that the microstructure of the substrates considerably influenced the surface morphology of deposited IZO films, and the least surface roughness of IZO was obtained after 5‐s plasma treatment. The IZO film deposited on PC with 5‐s plasma treatment presented an improved electrical conductivity and thermal stability after annealing at 120 °C in air, whereas the significant decrease in carrier concentration and increase in resistivity with extending plasma treatment time were observed, which was attributed to the elevated oxygen adsorption during annealing for a loosely packed structure. Moreover, the adhesion properties of IZO films with PC substrates decreased after 30‐s plasma treatment because of the significant difference on the surface polarity between the PC and thin films and the increased roughness caused by plasma etching. Copyright © 2016 John Wiley & Sons, Ltd.     

Effects of plasma treatment of carbon fibers on interfacial properties of BMI resin composites

High performance continuous fiber surface modification by inductively coupled RF plasma (ICP) and dielectric barrier discharge (DBD) low temperature plasma were conducted. X-ray photoelectron spectroscopy (XPS) and other analytical testing methods systematically studied plasma treatment time, discharge power, discharge pressure, etc, on fiber surface state, surface composition, and surface shape changes in the appearance and wetting properties. The results show that after plasma treatment the surface of the fiber is grafted with a large number of polar functional groups such as carboxyl groups and hydroxyl groups. The surface roughness increases, the surface free energy increases, and the fiber wetting property is significantly improved, resulting in improvement in interlaminar shear strength (ILSS) between the fiber and the resin matrix. Finally, the surfaces of the fibers and its relationship with interfacial properties of fiber reinforced bismaleimide composites are also discussed.     

Syntheses and characterization of functionalized polynorbornene dicarboximides for flexible substrates

In this study, we synthesized polynorbornene (PNB) dicarboximides substituted by monochlorophenyl group (PMCPhNDI) and dichlorophenyl group (PDCPhNDI) via ring‐opening polymerization using a ruthenium catalyst and investigated their thermal, mechanical, and optical properties. We also discussed the performance and application of the functionalized PNB dicarboximide films as flexible substrates for organic light‐emitting devices (OLEDs). The polymer films exhibited good optical transparency with an average transmittance of around 97% in the visible light region and good thermal stability with a 5% degradation temperature of >440°C. The polymers were applied for flexible displays, which were coated on indium tin oxide (ITO) thin films using a radio‐frequency planar magnetron sputtering system with changing the deposition substrate temperatures. A flexible OLED that was fabricated on the ITO‐grown polymer substrates exhibited a performance as comparable to the corresponding ITO‐grown glass substrates. Copyright © 2012 John Wiley & Sons, Ltd.     

等离子体改性聚氯乙烯的TiO2光催化降解研究

聚氯乙烯(PVC)是一种通用型塑料,无论采用挤出、注射或浸渍等方法均有优异的成型性能,至今仍是大量使用的弹性体.……     

Light-emitting diodes based on poly(2,3-diphenyl-1,4-phenylene vinylene)

In this paper we report polymer light-emitting diodes based on (2,3-diphenyl-1,4-phenylene vinylene) (DP-PPV), a novel π-conjugated polymer made by using the chlorine precursor route (CPR). Thin films of the precursor polymer were formed by spin-casting on indium-tin oxide (ITO) coated glass substrates, followed by thermal conversion to give DP-PPV thin films. Single layer DP-PPV LEDs were completed by thermally evaporating magnesium (Mg) electrodes. The electroluminescent characteristics of ITO/DP-PPV/Mg devices as well as variations between precursor polymer batches are presented. Bilayer LEDs were also made, for which tris(8-hydroxyquinoline)aluminum (Alq₃) was thermally sublimed on the fully converted DP-PPV films in vacuum, followed by Mg deposition. Both significant improvement in the quantum efficiency (up to 0.7% ph/el) and a reduction in the turn-on voltage of the device were found upon incorporation of the Alq₃ layer. These observations suggest that Alq₃ enhances the injection of electrons and also participates in the recombination process. © 1997 John Wiley & Sons, Ltd.     

Influence of oxygen plasma treatment on poly(ether sulphone) films

Poly(ether sulphone) (PES) is one of the most widely used materials in the micro-electronics industry and a good candidate for the substrates of flexible optoelectronic devices. In this work, the influences of oxygen plasma treatment on the surface chemical composition, surface morphology and optical transparency of PES films were investigated by means of X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscopy (FESEM), atomic force microscopy (AFM) and UV-visible spectrophotometry. The possible relations between the optical transparency of the substrate and the surface roughness and chemical composition were also studied. The oxygen plasma treatment seriously changed the surface chemical composition and made the surface more rough. Considerable amounts of sulphate species were found on the plasma-treated surface and the surface roughness values (R_a) increased monotonically with the increase of the treatment time. The PES films treated by 5 min, 15 min, 30 min and 45 min oxygen plasma demonstrated transmission of approximately 98, 94, 68 and 46%, respectively, in the wavelength range of 400-780 nm. The oxygen plasma induced decline of optical transparency of PES films might be attributed to both the increase of surface roughness and the changes of chemical composition of the film surface.     

Plasma for Modification of Polymers

The effect of nonpolymer-forming plasma (e.g., plasma of hydrogen, helium, argon, nitrogen) can be viewed as the following two reactions: 1) reaction of active species with polymer, and 2) formation of free radicals in polymer which is mainly due to the UV emitted by the plasma. The incorporation of nitrogen into the polymer surface by N₂ plasma and the surface oxidation by O₂ plasma are typical examples of the first effect. The latter effect generally leads to incorporation of oxygen in the form of carbonyl and hydroxyl and to some degree of cross-linking depending on the type of substrate; however, the degradation of polymer at the surface manifested by weight loss occurs in nearly all cases when polymers are exposed to plasma for a prolonged period of time. The effects of polymer-forming plasma is predominated by the deposition of polymer (plasma polymer); however, with some plasma-susceptible polymer substrates the effect of UV emission from polymer-forming plasma cannot be neglected. The mechanism of polymer formation can be explained by the stepwise reaction of active species and/or of an active specie with a molecule, and the chain addition polymerization of some organic compounds (e.g., vinyl monomers) is not the main route of polymer formation.

Plasma polymers contain appreciable amount of trapped free radicals; however, the concentration is highly dependent on the chemical structure of the monomer. In plasma polymerization, 1) triple bond and/or aromatic structure, 2) double bond and/or cyclic structure, and 3) saturated structure are three major functions which determine the rate of polymer formation and the properties of plasma polymers. The changes of some properties of plasma polymers with time are directly related to the concentration of trapped free radicals in plasma polymers. The amount of trapped free radicals in a plasma polymer is also influenced by the conditions of discharge; however, the UV irradiation from the polymer-forming plasma is not the main cause of these free radicals. Excess amount of free radicals are trapped during the process of polymer formation (rather than forming free radicals in the deposited polymer by UV irradiation). The properties of a plasma polymer is generally different from what one might expect from the chemical structure of the monomer, due to the fragmentation of atoms and/or functions during the polymerization process. This is another important factor to be considered for the modification of polymer surfaces by plasma polymerization.     

Effect of cold atmospheric plasma treatment on hydrophilic properties of fluorosilicone rubber

Vulcanized fluorosilicone rubber for aviation was treated by argon and oxygen cold atmospheric plasma (CAP) in order to modify its hydrophilic properties. The sample's chemical composition was analyzed by X‐ray photoelectron spectroscopy (XPS). The static contact angle, surface free energy, and adhesion strength were used to indicate the hydrophilic properties. Additionally, the surface morphologies of the specimens were observed by scanning electron microscopy (SEM) and atomic force microscopy (AFM). The results showed that the contact angle declined from 101.5° to 22°, and the surface energy rose from 21.3 to 71.2 mJ/m² after they were treated by argon plasma. Alternatively, the water contact angle decreased to 25.5°, and the surface energy increased to 70.6 mJ/m² after they were treated by oxygen plasma. In addition, the SEM and AFM images of the samples illustrate that the treated surface of fluorosilicone rubber becomes rougher than the non‐treated surface. The concentrations of carbon (C) and fluorine (F) elements of the material' surface decreased and the contents of O element greatly enriched after plasma treatment. Additionally, chemical group C―O and C―OH appeared after the treatment. However, the hydrophilic effect of the plasma treatment is aged after the specimens were stored for 8–12 h. Copyright © 2016 John Wiley & Sons, Ltd.     

On the correlation of surface charge and energy in non‐thermal plasma‐treated polyethylene

Non‐thermal non‐equilibrium oxidative air 40‐kHz frequency, 13.56‐MHz radiofrequency and 2.46‐GHz microwave discharge plasma treatment were used for modifying low‐density polyethylene foils. The untreated and treated samples were chemically characterised by X‐ray photoelectron spectroscopy. In order to estimate the extent of the plasma sources at distinct treatment times, surface charge and energy were determined by zeta potential (ζ) and surface tension measurements. In addition, the isoelectric points (IEPs) of the studied samples were ascertained, and surface property variations were appraised by ageing time. The overall outcome indicated that ζ‐potential and surface energy progressively changed after each treatment, as well as the influences of ageing on surface features, the IEP shifting to lower pH values and how all of these changes are associated with the new surface chemistry. This contribution seeks to shed light on topics related to polymer science and plasma‐based strategies for surface modification. Copyright © 2014 John Wiley & Sons, Ltd.