纳米二氧化钛对痕量铅的吸附性能研究

提出了纳米TiO2分离富集, 火焰原子吸收光谱法测定水样中痕量铅的新方法.考察了铅在纳米TiO2上的吸附动力学、最佳酸度和吸附容量.实验结果表明：在最佳实验条件下,纳米TiO2能定量、快速地吸附水中的痕量Pb^2＋,其静态吸附容量为17.90 mg/g.吸附在纳米TiO2上的Pb^2＋可用0.1 mol/L HNO3＋0.1 mol/L CH3COOH完全洗脱.对Pb2＋的检出限为2.57 ng/mL, 相对标准偏差为2.5% （n=11, ρ=0.10 μg/mL）,加标回收率在94.5%～102.5%之间.可用于实际水样中铅的测定.     

三乙烯四胺修饰β-环糊精交联树脂分离富集/原子吸收法测定大米中的铅、镉

该文制备了一种新型吸附材料三乙烯四胺修饰β-环糊精交联树脂(TETA-β-CDP),并对其进行红外光谱表征,优化了该吸附材料对痕量铅、镉的吸附和解析条件,建立了动态条件下同时分离富集/原子吸收光谱测定大米中铅和镉的新方法。在p H 5.5时,样品溶液以1.0 m L/min流速过柱,试液中的Pb2+和Cd2+可被该树脂定量富集,其动态饱和吸附容量分别为22.8,31.3 mg/g,吸附在TETA-β-CDP上的Pb2+和Cd2+可用0.1 mol/L HCl以0.8 m L/min流速完全洗脱。该方法对铅、镉的检出限(3σ,n=11)分别为0.038 mg/L和0.016 mg/L;线性范围分别为0.2~20 mg/L和0.05~2.5 mg/L;相对标准偏差(RSD)分别为2.8%和1.7%;加标回收率分别为97.5%~101.0%和95.0%~102.5%。该方法用于大米样品中痕量铅、镉的测定,结果满意。     

纳米钛富集水样重金属镉-胶体金免疫层析法快速检测方法的建立

研究了纳米TiO2分离富集水样中痕量镉的最佳反应条件,应用自制抗Cd(Ⅱ)-iEDTA(Isothiocya-nobenzyi-EDTA)螯合物的单克隆抗体,建立了快速检测环境水样中重金属镉残留的胶体金免疫层析法。采用纳米钛富集水样中的痕量镉,用洗脱剂将吸附的镉离子洗脱后,再采用胶体金免疫层析法快速判断镉离子浓度,进而分析水样中的重金属镉含量。结果表明,pH 9.0时,Cd可被纳米TiO2定量富集,吸附于纳米TiO2上的镉离子可用0.1 mol/L的EDTA.2Na(乙二胺四乙酸二钠)溶液定量脱附。在优化实验条件下,纳米TiO2对Cd的吸附容量为14.7 mg/g,富集倍数可达50倍。制备了比色法判定结果的胶体金试纸条,并建立了纳米TiO2富集-胶体金试纸条联用检测方法。对实测样品的检测耗时约90 min,该方法对Cd的定量下限可达5μg/L,适用于环境水样的检测。     

纳米B2O3/TiO2复合材料的制备及其对痕量银的分离富集性能研究与应用

制备了新型纳米B2O3/TiO2吸附材料,并采用扫描电镜(SEM)及红外光谱(IR)对其进行表征,优化了纳米B2O3/TiO2复合材料对试液中痕量银的吸附和解吸条件,建立了纳米B2O3/TiO2分离富集-原子吸收光谱测定痕量银的新方法。当pH 4.3时,在22℃下振荡20 min,Ag+能被该材料快速吸附,其静态饱和吸附容量为11.72 mg/g,吸附在纳米B2O3/TiO2上的Ag+可用0.1 mol/L HNO3-0.05 mol/L硫脲(1∶4)完全洗脱。该方法的检出限为2.01μg/L,线性范围为0.01～4.00 mg/L,相对标准偏差(RSD)为1.8%,加标回收率为95%～105%。方法应用于实际矿渣样品中痕量银的测定,结果满意。     

双硫腙修饰玻碳电极阳极溶出伏安法测定痕量镉和铅

报道了双硫腙修饰玻碳电极同时测定痕量镉和铅的电分析方法。镉和铅离子通过与电极表面的双硫腙发生螯合作用而富集在电极表面 ,同时在 -1 .2 0V(vs.SCE)还原成零价镉和铅 ,当电极电势从 -1 .2 0V向 -0 .3 0V扫描时 ,被还原的镉和铅从电极表面溶出 ,分别于 -0 .78V和 -0 .4 8V左右形成灵敏的阳极溶出峰。优化了支持电解质及pH值、双硫腙用量、富集电位及时间等实验参数。利用该修饰电极测定镉、铅的线性范围分别为 1 .0×1 0 - 8～ 2 .5× 1 0 - 6 mol L和 5 .0× 1 0 - 9～ 2 .5× 1 0 - 6 mol L。检测限分别为 5 .0× 1 0 - 9mol L和7.0× 1 0 - 1 0 mol L。该法用于实际水样中镉和铅的测定 ,平均回收率分别为 99.3 0 %和 99.5 4 %。     

纳米Al2O3微柱分离/富集-石墨炉原子吸收法测定环境试样中的痕量铅和镉

本文将纳米氧化铝微柱分离系统与石墨炉原子吸收光谱法联用,用于测定环境水样中的痕量铅和镉。较系统地考察了纳米Al2O3材料对镉和铅离子的吸附性能及影响因素;在优化的实验条件下本法对Pb和Cd的检出限(3σ)分别为0.189 ng/mL和0.0039 ng/mL;RSD%分别为3.9%和2.9%。     

离子液体双水相萃取-蒸气发生原子荧光法测定痕量镉

研究了离子液体1-异戊基-3-甲基咪唑溴代盐-K2HPO4-水双水相体系对镉-双硫腙络合物的萃取性能,建立了测定痕量镉的蒸气发生-原子荧光光谱法.经离子液体双水相萃取后,在离子液体相中的镉-双硫腙络合物经酸化后可直接与还原剂(NaBH4)混合进行蒸气发生反应,并经气液分离后将蒸气引入原子化器中进行原子荧光检测,离子液体的存在不影响蒸气发生过程.考察了双水相系统的组成以及相关实验条件对镉-双硫腙络合物萃取的影响.在最佳实验条件下,样品体积为1 mL时,测定痕量镉的线性范围为0.25～5.0 μg/L,检出限为0.07 μg/L; 相对标准偏差为3.4%(n=9, 2.0 μg/L Cd2+).用国家标准物质GBW08608(水中镉、铬、铜、镍、铅、锌成分分析标准物质)验证了方法的准确性,并对实际水样中的痕量镉进行了测定.     

纳米硅羟基磷灰石分离富集-火焰原子吸收法测定水样中痕量铅

提出了纳米硅羟基磷灰石(Si-HAP)分离富集,火焰原子吸收光谱法(FAAS)测定水样中痕量铅的新方法。考察了铅在纳米Si-HAP上的吸附动力学、最佳酸度和吸附容量。实验结果表明:在最佳实验条件下,纳米Si-HAP能定量、快速地吸附水中的痕量Pb2+,其静态吸附容量24.33 mg/g;吸附在纳米Si-HAP上的Pb2+可用0.01mol/L EDTA-Ca完全洗脱。本法对Pb2+的检出限为1.33 ng/mL,相对标准偏差为4.0%(n=11,c=1μg/mL),加标回收率在94.9%~102.0%之间。方法用于实际水样中铅的测定,结果满意。     

纳米二氧化钛富集-分光光度法测定水体中痕量5-磺基水杨酸

采用纳米TiO2化学吸附法富集水样中痕量5-磺基水杨酸。5-磺基水杨酸含有酚羟基(OH)和羧基(COOH)可与TiO2表面上的羟基(OH)发生酯化反应,形成稳定的六元环结构。纳米TiO2对5-磺基水杨酸的吸附量≤18.47mg/g,在pH2.5、吸附时间20min、吸附剂用量1.80g/L的条件下,纳米TiO2对试样中5-磺基水杨酸的吸附率达到99.0%,以5mL2mol/L NaOH为洗脱液,洗脱率达99.8%,对试样中5-磺基水杨酸的富集倍数达50倍,检出限(3σ,n=11)为26.7μg/L。本法操作简便,直接用于九龙江和海水中痕量5-磺基水杨酸的测定,结果准确,回收率达到95.5%～98.5%。     

纳米二氧化钛分离富集石墨炉原子吸收光谱法测定水样中痕量铅

提出了纳米TiO2分离富集,GFAAS测定水样中痕量铅的新方法。详细考察了纳米TiO2对铅的吸附行为,结果表明：在pH4．0时,Pb^2 可被纳米TiO2定量富集,吸附于纳米TiO2上的Pb^2 可用0．1mol／L的硝酸完全解脱。本法对Pb^2 的检出限为52ng／L,相对标准偏差为4．7％(n=10,C=0．02mg／L)。本法已用于实际水样中铅的测定,结果满意。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.