Accuracy of tomographic particle image velocimetry data on a turbulent round jet

Tomographic particle image velocimetry (Tomo-PIV) was applied on a turbulent round air jet to quantitatively assess the accuracy of velocity gradients obtained in the self-similar turbulent region. The jet Reynolds number based on the nozzle diameter (d) was Re_d = 3000. Mean velocity, turbulent intensities, and Reynolds shear stress at the center plane of the jet were measured. In addition, statistical results of Tomo-PIV along the axial direction were assessed by performing a separate set of two-dimensional two-component PIV experiments on a “side view” plane along the jet axis. Moreover, the probability distribution functions of four components of the measured velocity gradients in the axial and radial directions were validated by these “side view” planar PIV data. The root mean square of the velocity divergence values relative to the norm of the velocity gradient tensor was 0.36. Furthermore, the on- and off-diagonal components of the velocity gradients satisfied the axisymmetric isotropy conditions. The divergence error in the data affected only areas with low gradient magnitude. Therefore, turbulent structures in the regions with intense vorticity and dissipation can be closely monitored. On this basis, the joint pdfs of the invariants of the velocity gradient and strain and rotation tensor rates were produced and compared well with those in isotropic turbulence studies.     

Measurement of spectrum with particle image velocimetry

The purpose of this paper is to show that the measurement of turbulent spectrum using wholefield velocity techniques such as particle image velocimetry (PIV) is possible. Toward this end, data from the axial plane of a self-similar turbulent axisymmetric jet, at a Reynolds number, based on Taylor microscale of 30 has been analyzed. The two-dimensional velocity data are first high-pass filtered, which educes the vortices. An automated method is then used to identify the vortices and measure their properties. By directly measuring the energy of the vortices, it is possible to plot the turbulence spectrum. The spectrum presented here shows the presence of energy containing and inertial regimes. However, the smallest scales have not been resolved in the measurements. The slope of the spectrum in the inertial subrange is about −1.6. The number of vortices in the two regimes have also been measured. The number of vortices in the energy containing regime is substantially smaller than those in the inertial subrange. The technique has been verified by analyzing another dataset. These results show that the direct measurement of vortex properties with reasonable confidence is possible using PIV and an appropriate vortex eduction technique.     

Reynolds number effects on the behavior of a non-buoyant round jet

The behavior of a non-buoyant circular water jet discharged from a contraction nozzle was experimentally investigated. In this experiment, the Reynolds number of the jet, based on the mean velocity results obtained by particle image velocimetry (PIV), ranged from 177 to 5,142. From the experimental results, we found that the cross-sectional profile of the axial velocity for a laminar flow near the nozzle did not show a top-hat distribution, whereas the profiles with Reynolds number higher than 437 were almost top-hat. The length of the zone of flow establishment (ZFE) was found to decrease with increasing Reynolds number. The measured centerline velocity decayed more rapidly and, consequently, approached the theoretical equation earlier near the nozzle as the Reynolds number increased. The decay constant for the centerline velocity of the turbulent cases was relatively lower than that discovered in theory. It is assumed that this probably resulted from the use of the contraction nozzle. Verifying the similarity of the lateral velocity profiles demonstrated that the Gaussian curve was properly approximated only for the turbulent jets and not for the laminar or transitional flows. The jet half width seldom grew for the laminar or transitional flows, whereas it grew with increasing axial distance for the turbulent flows. The spreading rates for the turbulent flows gradually decreased with increasing Reynolds number. The normalized turbulence intensity along the jet centerline increased more rapidly with the axial distance as the Reynolds number increased, and tended to the constant values proposed by previous investigators. The Reynolds shear stress levels were also found to increase as the Reynolds number increased for the turbulent jets.     

An experimental study of a radial wall jet formed by the normal impingement of a round synthetic jet

The flow field of a radial wall jet created by the impingement of a round synthetic jet normal to a flat surface was characterized using hot-wire anemometry. In the synthetic wall jets the width of the outer layer was observed to increase linearly with the radial distance along the wall, while the local maximum velocity varied inversely. The synthetic wall jet exhibits self-similar behavior as distinguished by the collapse of the mean and rms velocity profiles when normalized by the outer layer scaling variables. Increasing the actuator driving amplitude at a fixed frequency (i) increased the growth rate of the outer layer, and (ii) decreased the decay rate of the local velocity maximum. The flow field of the synthetic wall jet was dominated by vortical structures associated with the actuator driving frequency, and harmonics connected with the interaction of the produced vortex structures. For the actuator conditions investigated, neither the classical laminar nor fully turbulent analytical solutions for continuous wall jets were amenable to modeling the synthetic wall jet profile due to the transitional and unsteady nature of the synthetic wall jet.     

Flow behaviour of turbulent nozzle jets issuing from bevelled collars

An experiment was conducted to investigate turbulent, low-speed air jets issuing from bevelled and non-bevelled circular collared-nozzle configurations. The collar-to-nozzle expansion ratio used was three and Reynolds number was approximately 20,000. Detailed mean flow velocity fields and velocity spectra of the resultant jet flows at different collar lengths and bevel angles were evaluated using hot-wire anemometry along both axial and radial directions of the jets. Centreline velocity decay was shown to be augmented when either collar length or bevel angle was increased, with the collar length playing a more dominant role. Results also showed that bevelled collared-jets vectored towards the longer collar-length region, the extent to which was enhanced when the collar length or bevel angle was increased. The study demonstrated that a bevelled collar exit could be used as an additional control device on top of the collar length to achieve finer jet flow control in terms of jet momentum vectoring and asymmetric jet spread.     

The turbulent/non-turbulent interface at the outer boundary of a self-similar turbulent jet

The flow at the outer boundary of a submerged self-similar turbulent jet at Re=2᎒³ is investigated experimentally by means of combined particle image velocimetry (PIV) laser-induced fluorescence (LIF) measurements. The jet fluid contains a fluorescent dye so that the LIF data can be used to discriminate between the jet fluid and the ambient fluid. The axial velocity, Reynolds stress, and vorticity are determined relative to the jet boundary. The results are compared against the conventional profiles, and the results of a direct numerical simulation of the turbulent far-wake behind a flat plate. The results show a sharp transition between rotational and irrotational fluid at the fluid interface, and the existence of a layer of irrotational velocity fluctuations outside the turbulent region.     

Large eddy simulation of vertical turbulent jets under JONSWAP waves

The effect of random waves on vertical plane turbulent jets is studied numerically and the mechanism behind the interaction of the jet and waves is analyzed. The large eddy simulation method is used and the σ-coordinate system is adopted. Turbulence is modeled by a dynamic coherent eddy model. The σ-coordinate transformation is introduced to map the irregular physical domain with a wavy free surface and an uneven bottom onto a regular computational domain. The fractional step method is used to solve the fil...     

The stability of low Reynolds number round jets

Multigrid cross-correlation digital particle image velocimetry (MCCDPIV) is used to investigate the stability and structure of low Reynolds number axisymmetric jets. The in-plane velocities, out-of-plane vorticity and some of the components of the Reynolds stress tensor are measured. Two Reynolds numbers based on the orifice outlet diameter are examined (680 and 1,030) at two different positions: one close to the orifice, ranging from 2D ₀ to 5D ₀ (D ₀ is the orifice diameter); and the other further from the orifice, ranging from 10D ₀ to 14.4D ₀. The results show that the lower Reynolds number jet (Re=680) is marginally unstable in the near-orifice region and is best described as laminar. Further downstream some intermittent structures are observed in the jet, and the growth in integrated turbulent kinetic energy with axial position indicates that the jet is also unstable in this region. For the higher Reynolds number jet (Re=1,030) the increasing size and intensity of vortical structures in the jet in the near-orifice region observed from the MCCDPIV data and the growth in integrated turbulent kinetic energy indicate that the jet is unstable. Further downstream this jet is best described as transitional or turbulent. From flow visualisation images in the near-orifice region it seems that, for both Reynolds numbers, shear layer roll-up occurs when the jet exits the orifice and enters the quiescent fluid in the tank, resulting in vortical structures that appear to grow as the jet proceeds. This is indicative of instability in both cases and is consistent with previous flow visualisation studies of low Reynolds number round jets. Discrepancies observed between the flow visualisation results and the MCCDPIV data is addressed. On the basis of flow visualisation results it is generally assumed that round jets are unstable at very low Reynolds number, however the present work shows that this assertion may be incorrect.     

Mass and momentum transport in the near field of swirling turbulent jets. Effect of swirl rate

Local transport of the flow momentum and scalar admixture in the near-field of turbulent swirling jets (Re = 5,000) has been investigated by using a combination of the particle image velocimetry and planar laser-induced fluorescence methods. Advection and turbulent and molecular diffusions are evaluated based on the measured distributions of the mean velocity and concentration and the Reynolds stresses and fluxes. As has been quantified from the data, the flow swirl intensifies the entrainment of the surrounding fluid and promotes mass and momentum exchange in the outer mixing layer. A superimposed swirl results in the appearance of a wake/recirculation region at the jet axis and, consequently, the formation of an inner shear layer. In contrast to the scalar admixture, the momentum exchange in the inner shear layer is found to be strongly intensified by the swirl. For the jet with the highest considered swirl rate, a substantial portion of the surrounding fluid is found to enter the unsteady central recirculation zone, where it mixes with the jet that is issued from the nozzle. The contribution of the coherent velocity fluctuations, which are induced by large-scale vortex structures, to the turbulent transport has been evaluated based on triple decomposition, which was based on proper orthogonal decomposition analysis of the velocity data sets. For the considered domain of the jet with the highest swirl rate and vortex breakdown, the contributions of detected helical vortex structures, inducing pressing vortex core, to the radial fluxes of the flow momentum and the scalar admixture are found to locally exceed 65% and 80%, respectively.     

Measurements in the near flow field of an isosceles triangular turbulent free jet

The near field mean flow and turbulence characteristics of a turbulent jet of air issuing from a sharp-edged isosceles triangular orifice into still air surroundings have been examined experimentally using hot-wire anemometry and a pitot-static tube. For comparison, some measurements were made in an equilateral triangular free jet and in a round free air jet, both of which also issued from sharp-edged orifices. The Reynolds number, based on the orifice equivalent diameter, was 1.84×10⁵ in each jet. The three components of the mean velocity vector, the Reynolds normal and primary shear stresses, the one-dimensional energy spectra of the streamwise fluctuating velocity signals and the mean static pressure were measured. The mean streamwise vorticity, the half-velocity widths, the turbulence kinetic energy and the local shear in the mean streamwise velocity were obtained from the measured data. It was found that near field mixing in the equilateral triangular jet is faster than in the isosceles triangular and round jets. The mean streamwise vorticity field was found to be dominated by counter-rotating pairs of vortices, which influenced mixing and entrainment in the isosceles triangular jet. The one-dimensional energy spectra results indicated the presence of coherent structures in the near field of all three jets and that the equilateral triangular jet was more energetic than the isosceles triangular and round jets.     

Velocity measurements in a plane turbulent air jet at moderate Reynolds numbers

An experimental investigation of the moderate Reynolds number plane air jets was undertaken and the effect of the jet Reynolds number on the turbulent flow structure was determined. The Reynolds number, which was defined by the jet exit conditions, was varied between 1000 and 7000. Other initial conditions, such as the initial turbulence intensity, were kept constant throughout the experiments. Both hot-wire and laser Doppler anemometry were used for the velocity measurements. In the moderate Reynolds number regime, the turbulent flow structure is in transition. The average size and the number of the large scale of turbulence (per unit length of jet) was unaffected by the Reynolds number. A broadening of the turbulent spectra with increasing Reynolds number was observed. This indicated that there is a decrease in the strength of the large eddies resulting from a reduction of the relative energy available to them. This diminished the jet mixing with the ambient as the Reynolds number increased. Higher Reynolds numbers led to lower jet dilution and spread rates. On the other hand, at higher Reynolds numbers the dependence of jet mixing on Reynolds number became less significant as the turbulent flow structure developed into a self-preserving state.List of symbols b _u velocity half-width of the jet - C _u, C _u,0 constants defining the velocity decay rate - D nozzle width - E _u one dimensional power spectrum of velocity fluctuations - f frequency - K _u, K _u,0 constants defining the jet spread rate - k wavenumber (2f/U) - L longitudinal integral scale - R ₁₁ correlation function - r separation distance - Re jet Reynolds number (U ₀ D/v) - St Strouhal number (fD/U ₀) - t time - U axial component of the mean velocity - U _m mean velocity on the jet axis - U ₀ mean velocity at the jet exit - u the rms of u - u fluctuating component of the axial velocity - V lateral component of the mean velocity - fluctuating component of the lateral velocity - x axial distance from the nozzle exit - y lateral distance from the jet axis - z spanwise distance from the jet axis - v kinematic viscosity - time lag A version of this paper was presented as paper no. 86-0038 at the AIAA 24th Aerospace Sciences Meeting, Reno NV, USA, January 1986     

Evolution of flow structure in impinging three-dimensional axial and radial jets

Direct numerical simulations of the flow field of an element of banks of impinging axial and radial slot jets for different Reynolds number are presented. Simulations have been obtained from the solution of the Navier–Stokes equations. Results show for the chosen geometry a transition from steady to periodic to chaotic flow with increasing Reynolds number. The transition Reynolds number is nearly 50% smaller for the radial jet than for the axial jet. Period doubling has been observed for both cases, but only the radial jet shows periodic windows of chaos. © 1997 John Wiley & Sons, Ltd.     

Turbulent structure during transition to self-similarity in a round jet

 The developing turbulent region of a round jet was investigated using an improved implementation of digital particle image velocimetry (DPIV). The two-dimensional flow field in planes normal and parallel to the axial velocity was measured at locations between 15 and 30 diameters downstream, for two Reynolds numbers of 5500 and 16,000. The study consisted of instantaneous snapshots of the velocity and vorticity fields as well as measurements of velocity correlations up to third order. In this regime, the Reynolds number had a significant effect on both the instantaneous flow structure and the profiles of mean velocity across the jet. Coherent streamwise structures were present in the jet core for the lower Reynolds number. Additional structures whose evolution was governed by time scales two orders of magnitude larger than the convective scale inside the jet were observed in the entrainment field. The velocity correlations provided further support for the validity of DPIV turbulence measurements. The data was consistent with the equations of motion and momentum was conserved. DPIV measurements of turbulent kinetic energy components agreed with the hot-wire measurements of previous studies. Received: 27 November 1996/Accepted: 14 July 1997     

Volumetric three-component velocimetry measurements of the turbulent flow around a Rushton turbine

Volumetric three-component velocimetry measurements have been taken of the flow field near a Rushton turbine in a stirred tank reactor. This particular flow field is highly unsteady and three-dimensional, and is characterized by a strong radial jet, large tank-scale ring vortices, and small-scale blade tip vortices. The experimental technique uses a single camera head with three apertures to obtain approximately 15,000 three-dimensional vectors in a cubic volume. These velocity data offer the most comprehensive view to date of this flow field, especially since they are acquired at three Reynolds numbers (15,000, 107,000, and 137,000). Mean velocity fields and turbulent kinetic energy quantities are calculated. The volumetric nature of the data enables tip vortex identification, vortex trajectory analysis, and calculation of vortex strength. Three identification methods for the vortices are compared based on: the calculation of circumferential vorticity; the calculation of local pressure minima via an eigenvalue approach; and the calculation of swirling strength again via an eigenvalue approach. The use of two-dimensional data and three-dimensional data is compared for vortex identification; a ‘swirl strength’ criterion is less sensitive to completeness of the velocity gradient tensor and overall provides clearer identification of the tip vortices. The principal components of the strain rate tensor are also calculated for one Reynolds number case as these measures of stretching and compression have recently been associated with tip vortex characterization. Vortex trajectories and strength compare favorably with those in the literature. No clear dependence of trajectory on Reynolds number is deduced. The visualization of tip vortices up to 140° past blade passage in the highest Reynolds number case is notable and has not previously been shown.     

Multiscale simulations and experiments on water jet atomization

Numerical simulation of primary atomization at high Reynolds number is still a challenging problem. In this work a multiscale approach for the numerical simulation of liquid jet primary atomization is applied, using an Eulerian-Lagrangian coupling. In this approach, an Eulerian volume of fluid (VOF) method, where the Reynolds stresses are closed by a Reynolds stress model is applied to model the global spreading of the liquid jet. The formation of the micro-scale droplets, which are usually smaller than the grid spacing in the computational domain, is modelled by an energy-based sub-grid model. Where the disruptive forces (turbulence and surface pressure) of turbulent eddies near the surface of the jet overcome the capillary forces, droplets are released with the local properties of the corresponding eddies. The dynamics of the generated droplets are modelled using Lagrangian particle tracking (LPT). A numerical coupling between the Eulerian and Lagrangian frames is then established via source terms in conservation equations. As a follow-up study to our investigation in Saeedipour et al. (2016a), the present paper aims at modelling drop formation from liquid jets at high Reynolds numbers in the atomization regime and validating the simulation results against in-house experiments. For this purpose, phase-Doppler anemometry (PDA) was used to measure the droplet size and velocity distributions in sprays produced by water jet breakup at different Reynolds numbers in the atomization regime. The spray properties, such as droplet size spectra, local and global Sauter-mean drop sizes and velocity distributions obtained from the simulations are compared with experiment at various locations with very good agreement.     

Numerical simulation and visualization of fiber suspension in a turbulent round jet

The turbulent properties of the fiber suspension in a turbulent round jet are numerically simulated and visualized, and some of the results are compared with the experimental data. The effects of the Reynolds number, fiber volume fraction, and aspect ratio are analyzed. The results show that the fiber injection in the flow has a delay effect on the streamwise velocity decay along the jet axis, and such an effect becomes more obvious with the increases in the fiber volume fraction and aspect ratio and the decrease in the Reynolds number. The flow with fibers shows an increase in the streamwise velocity along the radial direction, and the increase magnitude is directly proportional to the fiber volume fraction and aspect ratio and inversely proportional to the Reynolds number. The presence of fibers makes the turbulent kinetic energy and Reynolds stress increase, and the extent increases with the fiber volume fraction, Reynolds number, and fiber aspect ratio.     

PIV measurements of a turbulent jet issuing from round sharp-edged plate

An experimental investigation is presented of a turbulent jet issuing from a round sharp-edged orifice plate (OP) into effectively unbounded surroundings. Planar measurements of velocity were conducted using Particle Image Velocimetry (PIV) in the near and transition regions. The Reynolds number, based on the jet initial diameter and velocity, is approximately 72,000. The instantaneous and mean velocities, Reynolds normal and shear stresses were obtained. The centerline velocity decay and the half-velocity radius were derived from the mean velocity. It is revealed that primary coherent structures occur in the near field of the OP jet and that they are typically distributed asymmetrically with respect to the nozzle axis. Comparison of the present PIV and previous hot-wire measurements for the OP jet suggests that high initial turbulence intensity leads to reduced rates of decay and spread of the mean flow field and moreover a lower rate of variation of the turbulence intensity. Results also show that self-similarity of the mean flow is well established from the transition region while the turbulent statistics are far from self-similar within the measured range to 16 diameters.     

Effect of jet-to-plate spacing in laminar array jets impinging

The rate of heat transfer from a plate due to impinging of an array of jets was investigated. The effect of jet-to-plate spacing in a confined array of impinging laminar square jets was investigated numerically through the solution of Navier Stokes and energy equations. The simulation is carried out for the jet-to-plate spacing between 2 B and 20 B and for jet-to-jet spacing of 4 B, where B is the jet width. Five in-line jets subjected to across-flow were used in this investigation. Also, six different ratios of jet to cross-flow velocity are simulated (0.5, 1.0, 2.5, 5, 7.5 and 10) for the jet Reynolds number of 200. The predicted results show a formation of one or two ground horseshoe vortices between the jets. In addition, a horseshoe vortex forms at different position between the orifice and impinging plates due to the interaction of two jets before they combine. The number of the ground horseshoe vortex and its size are strongly affected by the jet-to-plate spacing and by jet to cross-flow velocity ratio. The effect of jet-to-plate spacing and jet to cross-flow velocity ratio on heat transfer is presented and discussed.     

A technique for measuring Lagrangian and Eulerian particle statistics in a turbulent flow

An experimental technique is described which has been developed to study particle dispersion in a round turbulent jet. Droplets are injected on the jet axis, and a laser sheet and position sensitive photomultiplier tube are used to track their radial displacement. Data processing is greatly simplified compared to video or photo imaging techniques which provide similar measurements. Statistically large samples are used to calculate dispersion and axial velocity as a function of axial downstream distance or particle time-of-flight. Dispersion and velocity statistics can be computed which are Lagrangian or Eulerian in nature. The technique has been demonstrated with 69 m droplets of hexadecane in a jet of air with a Reynolds number of 15,000; in principle it could be used to study the motion of very small, quasi-fluid particles.     

Experimental study of the mean wake of a tidal stream rotor in a shallow turbulent flow

The mean wake of a three-bladed horizontal axis tidal stream turbine operating at maximum power coefficient has been investigated experimentally in a wide flume with width 11 times the depth, providing minimal restriction to transverse wake development and behaviour of large-scale horizontal turbulence structures. This is an important first stage for understanding wake interaction in turbine arrays and hence large-scale power generation. The rotor diameter has a typical value of 60% of the depth and the thrust coefficient is representative of a full-scale turbine. The shear layers originating from the rotor tip circumference show classic linear expansion downstream, with the rate of a plane shear layer vertically and 1.5 times that horizontally. These shear layers merge by around 2.5 diameters downstream forming a self-similar two-dimensional wake beyond eight diameters downstream with a virtual origin at two diameters downstream of the rotor plane. The spreading rate is somewhat less than that for solid bodies. The detailed velocity measurements made in the near wake show rotation and vorticity similar to that measured previously for wind and marine turbines although with asymmetry associated with bed and surface proximity. The longitudinal circulation in a transverse plane is conserved at about 1% of the swept circulation from the blade tip within two diameters downstream, the extent of detailed measurement. Turbines are usually designed using blade element momentum theory in which velocities at the rotor plane are characterised by axial and tangential induction factors and it is now possible to see how this idealisation relates to actual velocities. The axial induction factor corresponds to velocity deficits at 0.4–0.8 radii from the rotor axis across the near wake while the tangential induction factor at the rotor plane corresponds to velocities at 0.4–0.6 radii between 1–2 diameters downstream, indicating some general correspondence. For the two-dimensional self-similar far wake the two parameters defining the centreline velocity deficit and the transverse velocity profiles are likely to be insensitive to Reynolds number in turbulent conditions.