Characterization and catalytic-hydrogenation behavior of SiO2-embedded nanoscopic Pd, Au, and Pd-Au alloy colloids

Colloids embedded in a silica sol-gel matrix were prepared by using fully alloyed Pd-Au colloids, and pure Pd and Au colloids stabilized with tetraalkylammonium bromide following a modified sol-gel procedure with tetrahydrofuran (THF) as the solvent. Tetraethoxysilicate (TEOS) was used as the precursor for the silica support. The molar composition of the sol was TEOS/THF/H2O/HCl = 1:3.5:4:0.05 for the bimetallic Pd-Au and TEOS/THF/H2O/HCl = 1:4.5:4:0.02 for Pd and Au monometallic systems. After refluxing, the colloid was added as a 4.5 wt % solution in THF for Pd-Au, 10.2 wt % solution in THF for Pd and 8.4 wt % solution in THF for Au at room temperature. The gelation was carried out with vigorous stirring (4 days) under an Ar atmosphere. Following these procedures, bimetallic Pd-Au-SiO2 catalysts with 0.6 and 1 wt % metal, and monometallic Pd- and Au-SiO2 catalysts with 1 wt % metal were prepared. These materials were further treated following four different routes: 1) by simple drying, 2) in which the dried catalysts were calcined in air at 723 K and then reduced at the same temperature, 3) in which they were directly reduced in hydrogen at 723 K, and 4) in which the surfactant was extracted using an ethanol-heptane azeotropic mixture. The catalysts were characterized by nitrogen adsorption-desorption isotherms at 77 K, H2 chemisorption measurements, solid-state 1H, 13C, 29Si-CP/MAS-NMR spectroscopy, powder X-ray diffraction (XRD), small angle X-ray scattering (SAXS), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), and 197Au M?ssbauer spectroscopy. The physical characterization by a combination of these techniques has shown that the size and the structural characteristics of the Pd-Au colloid precursor are preserved when embedded in an SiO2 matrix. Catalytic tests were carried out in selective hydrogenation of 3-hexyn-1-ol, cinnamaldehyde, and styrene. These data showed evidence that alloying Pd with Au in bimetallic colloids leads to enhanced activity and most importantly to improved selectivity. Also, the combination of the two metals resulted in catalysts that were very stable against poisoning, as was evidenced for the hydrogenation of styrene in the presence of thiophene.     

Electrosorption of hydrogen into palladium-gold alloys

Hydrogen electrosorption into Pd-Au alloys has been studied in acidic solutions (1 M H₂SO₄) using cyclic voltammetry. Pd-Au electrodes with limited volume were prepared by electrochemical co-deposition. It was found that the maximum H/(Pd+Au) ratios decrease monotonically with increasing gold content and reach zero at ca. 70 at% Au. Similarly to the case of Pd limited volume electrodes, two peaks in the hydrogen region, corresponding to two types of sorbed hydrogen, are observed on voltammograms for Pd-rich alloys. The hydrogen capacity, H/(Pd+Au), measured electrochemically, depends on the sweep rate in the cyclic voltammetry experiments, which suggests that two different mechanisms for hydrogen desorption from the Pd-Au alloy are possible. After a strong decrease of Pd concentration at the electrode surface, caused by long cyclic polarization to sufficiently anodic potentials, the amount of absorbed hydrogen is still significant for alloys initially rich in Pd. The results obtained from CO adsorption experiments suggest that only Pd atoms are active in the hydrogen absorption/desorption process. Electronic Publication     

不同状态Au对甲酸在Pd催化剂上电催化性能的影响

合成并比较了碳载Au(Au/C)、碳载Pd(Pd/C)、碳载高合金化Pd-Au(Pd-Au/C-T)和碳载非合金化Pd-Au(Pd-Au/C-H)催化剂对甲酸氧化的电催化活性和稳定性.结果表明,Au/C对甲酸氧化基本没有电催化活性,而Pd/C对甲酸氧化有较好的电催化性能,Au的加入能进一步提高Pd催化剂对甲酸氧化的电催化活性和稳定性,特别是Pd-Au/C-T对甲酸氧化的电催化活性和稳定性要好于Pd-Au/C-H,更远好于Pd/C催化剂.相关反应机理有待进一步揭示.     

Preparation and characterization of silica supported Au-Pd model catalysts

Au-Pd bimetallic model catalysts were synthesized as alloy clusters on SiO2 ultrathin films under ultrahigh vacuum (UHV) conditions. The surface composition and morphology were characterized with low energy ion scattering spectroscopy (LEIS), infrared reflection absorption spectroscopy (IRAS), and temperature programmed desorption (TPD). Relative to the bulk, the surface of the clusters is enriched in Au. With CO as a probe, IRAS and TPD were used to identify isolated Pd sites at the surface of the supported Au-Pd clusters. Ethylene adsorption and dehydrogenation show a clear structure-reactivity correlation with respect to the structure/composition of these Au-Pd model catalysts.     

乙烯基乙酸酯合成钯-金催化剂中金的助催化作用

硅胶负载的钯-金双金属催化剂是乙烯乙酰氧基化制乙烯基乙酸酯(VA)的高选择性催化剂,本文应用平面和负载纳米颗粒模型催化剂体系研究金的助催化作用,应用低能离子散射谱、低能电子衍射、X射线光电子能谱、反射红外吸收光谱及程序升温脱附等技术表征这些模型催化剂.结果表明,金的主要助催化作用是隔离催化剂表面的催化活性钯原子,形成孤立的钯活性中心,从而大大抑制或消除反应物和/或产物在毗邻多原子钯中心上的深度分解,提高VA合成的选择性及活性.同时由于形成了孤立的钯原子活性中心,反应副产物或中间物之一的一氧化碳吸附较弱,避免了催化剂表面的一氧化碳中毒,进而提高催化活性.     

On the enhanced electrocatalytic activity of Pd overlayers on carbon-supported gold particles in hydrogen electrooxidation

Palladium-gold particles with varied composition were prepared by Pd electrochemical deposition on Au nanoparticles immobilized on model carbon support. Pd-Au/C catalysts were characterized ex situ by transmission electron microscopy, energy dispersive X-ray analysis and X-ray photoelectron spectroscopy, and in situ, by underpotential deposition of hydrogen and copper adatoms, and CO stripping. Hydrogen oxidation reaction on pristine and CO-poisoned Pd-Au/C particles was studied using rotating disk electrode (RDE) technique. It was found that the decrease of the effective Pd overlayer thickness below ca. two monolayers resulted in a two-fold increase of the exchange current density of the hydrogen oxidation reaction and in significant increase of CO tolerance.     

Formation of Pd/Au nanostructures from Pd nanowires via galvanic replacement reaction

Bimetallic nanostructures with non-random metal atoms distribution are very important for various applications. To synthesize such structures via benign wet chemistry approach remains challenging. This paper reports a synthesis of a Au/Pd alloy nanostructure through the galvanic replacement reaction between Pd ultrathin nanowires (2.4 +/- 0.2 nm in width, over 30 nm in length) and AuCl3 in toluene. Both morphological and structural changes were monitored during the reaction up to 10 h. Continuous changes of chemical composition and crystalline structure from Pd nanowires to Pd68Au32 and Pd45Au55 alloys, and to Au nanoparticles were observed. More interestingly, by using combined techniques such as high-resolution transmission electron microscopy (HRTEM), X-ray diffraction (XRD), energy dispersive X-ray spectrometry (EDS), UV-vis absorption, and extended X-ray absorption fine structure (EXAFS) spectroscopy, we found the formation of Pd68Au32 non-random alloy with Au-rich core and Pd-rich shell, and random Pd45Au55 alloy with uniformly mixed Pd and Au atom inside the nanoparticles, respectively. Density functional theory (DFT) calculations indicated that alkylamine will strongly stabilize Pd to the surface, resulting in diffusion of Au atoms into the core region to form a non-random alloy. We believe such benign synthetic techniques can also enable the large scale preparation of various types of non-random alloys for several technically important catalysis applications.     

Probing the interface in vapor-deposited bimetallic Pd-Au and Pt-Au films by CO adsorption from the liquid phase

Bimetallic Pd-Au and Pt-Au and monometallic Pd, Pt, and Au films were prepared by physical vapor deposition. The resulting surfaces were characterized by means of XPS, AFM, and CO adsorption from the liquid phase (CH2Cl2) monitored by ATR-IR spectroscopy. CO adsorption combined with ATR-IR proved to be a very sensitive method for probing the degree of interdiffusion occurring at the interfaces whose properties were altered by variation of the Pd and Pt film thickness from 0.2 to 2 nm. Because no CO adsorption was observed on Au, the evaporation of Pt-group metals on Au allowed us to study the effect of dilution on the adsorption properties of the surfaces. At equivalent Pd film thickness, the evaporation of Au reduced the amount of adsorbed CO and caused the formation of 2-fold bridging CO, which was almost absent in monometallic surfaces. Additionally, the average particle size on Pd-Au surfaces was smaller than that on monometallic Pd surfaces. The results indicate that a Pd/Au diffuse interface is formed that affects the Pd particle size even more drastically than the simple decrease in Pd film thickness in monometallic surfaces. Pt-Au surfaces were less sensitive to CO adsorption, indicating that the two metals do not mix to a significant extent. The difference in the interfacial behavior of Pd and Pt in the bimetallic gold films is traced to the largely different Pd-Au and Pt-Au miscibility gaps.     

First principles investigations of Pd-on-Au nanostructures for trichloroethene catalytic removal from groundwater

Catalytic groundwater remediation from chlorinated organic solvents like trichloroethene (TCE) has been found to be more effective and sustainable than traditional non-destructive methods. Among the experimentally studied catalyst materials, Pd-decorated Au nanoparticles show the highest activity and selectivity combined with the best resistance towards poisoning by chemicals present in groundwater. In this study the thermochemistry and adsorption geometries of TCE and its hydrodechlorination products are investigated via density functional theory calculations. Various model systems for Pd-supported Au nanoparticles are addressed. The adsorption of TCE is endothermic on bare Au(111), almost thermoneutral or slightly exothermic on Pd-Au surface alloys and clearly exothermic on Pd overlayer structures on Au(111). The strongest chemisorption is on the di-σ configuration between Pd atoms over the smallest 2D Pd clusters containing only a few Pd atoms. These are not, however, the best catalysts as they are too small to co-adsorb hydrogen needed for hydrodechlorination reaction. We demonstrate good correlation between adsorption energies and the d-band center of the system. The variation of adsorption energy from the one Pd-Au composition to the other can be tentatively assigned to be due to the ligand and coordination effects. Also, the ensemble effects are important; without the right ensemble the adsorption is weak or endothermic.     

碳纳米管载Pd-Au催化剂的合成及其对甲酸氧化的电催化性能

将萘-1-亚甲基膦酸通过π-π堆积作用修饰在多壁碳纳米管(MWCNT)上,然后制备了MWCNT载Pd(Pd/MWCNT)催化剂。 利用Pd和HAuCl4间的置换反应制得MWCNT载Pd-Au(Pd-Au/MWCNT)催化剂。 透射电子显微镜(TEM)、X射线光电子能谱(XPS)和X射线衍射光谱(XRD)测试结果显示,非合金化的Pd-Au纳米粒子均匀分布在MWCNT表面。 循环伏安和计时电流测试显示,非合金化Pd-Au/MWCNT催化剂对甲酸氧化的电催化活性以及稳定性优于Pd/MWCNT催化剂。     

Polymer-Protected Bimetallic Clusters. Preparation and Application to Catalysis

Colloidal dispersions of polymer-protected Pd/Pt and Pd/Au bimetallic clusters were prepared by reduction of an alcoholic solution of PdCl₂ and H₂PtCl₆ or HAuCl₄ in the presence of poly(N-vinyl-2-pyrrolidone). The reduction can be carried out by refluxing in alcohol or by irradiation with visible light. The dispersions of the bimetallic clusters obtained are stable for months at room temperature and have from dark brown to brownish red color. Transmission electron micrographs show that the bimetallic clusters are composed of well-dispersed ultrafine particles of uniform size, about 1.5 nm for Pd-Pd and 3.4 nm for Pd-Au in diameter. The catalytic activity of the bimetallic clusters depends on the metal composition. In the case of the partial hydrogenation of 1, 3-cyclooctadiene, the activity went through a maximum when the alloy composition reached about 80% Pd and 20% Pt, or 60% Pd and 40% Au.     

Selected electrochemical properties of Pd–Au alloys: hydrogen absorption and surface oxidation

Hydrogen absorption into and surface oxidation of Pd–Au alloys in acidic solutions were studied by cyclic voltammetry (CV) and chronoamperometry (CA) coupled with the electrochemical quartz crystal microbalance (EQCM). The influence of alloy bulk and surface composition on the process of oxidation of absorbed hydrogen was examined. The stresses induced by hydrogen insertion in Pd–Au alloys were compared with the case of pure Pd. The potential corresponding to the formation of a monolayer of surface oxide was determined for Pd–Au alloys of different surface states. Electrochemical dissolution of Pd–Au alloys was investigated.     

CO adsorption on pure and binary-alloy gold clusters: a quantum chemical study

We performed density-functional theory analysis of nondissociative CO adsorption on 22 binary Au-alloy (Au(n)M(m)) clusters: n=0-3, m=0-3, and m+n=2 (dimers) or 3 (trimers), M=Cu/Ag/Pd/Pt. We report basis-set superposition error corrections to adsorption energies and include both internal energy of adsorption (DeltaU(ads)) and Gibbs free energy of adsorption (DeltaG(ads)) at standard conditions (298.15 K and 1 atm). We found onefold (atop) CO binding on all the clusters except Pd2 (twofold/bridged), Pt2 (twofold/bridged), and Pd3 (threefold). In agreement with the experimental results, we found that CO adsorption is thermodynamically favorable on pure Au/Cu clusters but not on pure Ag clusters and also observed the following adsorption affinity trend: Pd>Pt>Au>Cu>Ag. For alloy dimers we found the following patterns: Au2>M Au>M2 (M=Ag/Cu) and M2>M Au>Au2 (M=Pd/Pt). Alloying Ag/Cu dimers with (more reactive) Au enhanced adsorption and the opposite effect was observed for PdPt dimers. The Ag-Au, Cu-Au, and Pd-Au trimers followed the trends observed on dimers: Au3>M Au2>M2Au>M3 (M=Ag/Cu) and Pd3>Pd2Au>PdAu2>Au3. Interestingly, Pt-Au trimers reacted differently and alloying with Au systematically increased the adsorption affinity: PtAu2>Pt2Au>Pt3>Au3. A strikingly different behavior of Pt is also manifested by the triplet spin state and onefold (atop) binding in Pt3-CO which is in contradiction with the singlet spin state and threefold binding in Pd3-CO. We found a linear correlation between CO binding energy (BE) and elongation of the CO bond. For Ag-Au and Cu-Au clusters, the increase in CO BE (and elongation of the C-O bond which is probably due to the back donation) is accompanied by the decrease in the cluster-CO distance suggesting that the donation (from 5sigma highest occupied molecular orbital in CO to cluster lowest unoccupied molecular orbital) mechanism also contributes to the BE. For Pd-Au clusters, the cluster-CO distance (and CO bond length) increases with increase in the BE, suggesting that the donation mechanism may not be important for those clusters. No clear trend was observed for Pt-Au clusters.     

The anodic oxidation of gold + palladium alloys

The anodic oxidation of Au+Pd alloys has been studied in solutions of 1 M H₂SO₄ and 0.1 M K₂SO₄ by voltammetric methods. A linear relationship between oxide reduction maximum and bulk alloy composition, often used to determine the surface composition of homogeneous alloys, could be shown to hold only for alloys up to 60 at% gold. At higher gold content the Au oxide peak must be additionally evaluated. With continuous cycling in acid solution the anodic dissolution of Pd, especially from gold-rich places, leads to a rather heterogeneous surface. The O--chemisorption is not governed by a transfer mechanism from Pd to Au surface atoms. The alloys are able to absorb the oxygen species generated in the positive potential region; however, this ability decreases with increase of the gold content.     

甲醇与氧在银钯合金上的吸附和反应

本文运用UPS、超高真空程序升温反应谱(TPRS)研究了氧和甲醇在银钯合金上的吸附和反应。实验结果表明, 合金表面存在两种分别与Ag和Pd原子有关的活性位; 少量钯原子的存在, 一方面提供了甲醇分解反应的活性中心, 另一方面通过与银之间的电子相互作用, 削弱了氧与银的结合, 增强了表面吸附氧的反应活性, 从而改变了甲醇氧化反应的选择性。     

Surface composition of PdCuAu ternary alloys: a combined LEIS and XPS study

PdCuAu ternary alloy samples with different composition were synthesized on top of ZrO₂‐modified porous stainless steel disks by the sequential electroless deposition technique. The structure, morphology and bulk composition of the samples were characterized by X‐ray diffraction (XRD), scanning electron microscopy and energy dispersive X‐ray spectroscopy (EDX). Complete alloy formation with a pure fcc phase for the Pd₇₁Cu₂₆Au₃, Pd₇₀Cu₂₅Au₅ and Pd₆₇Cu₂₄Au₉ samples and a bcc structure for the Pd₆₂Cu₃₆Au₂ and Pd₆₀Cu₃₇Au₃ samples were obtained upon annealing at 500 °C for 120 h as revealed by XRD. A combination of low‐energy ion scattering (LEIS) and X‐ray photoelectron spectroscopy (XPS) was used to investigate the surface properties of the PdCuAu alloys. XPS results confirmed alloy formation under the annealing conditions. XPS analysis also revealed that the near‐surface regions of the alloys became enriched in Pd with respect to the bulk composition determined by EDX. In contrast, LEIS and angle‐resolved XPS analyses showed that the top‐most surface layers in all samples were copper‐rich compared with the bulk composition. This high Cu surface concentration could impart resistance to bulk sulfide formation to the PdCuAu alloy membranes. Copyright © 2015 John Wiley & Sons, Ltd.     

The interaction of CO with PdAg/Pd(111) surface alloys--a case study of ensemble effects on a bimetallic surface

The interaction of CO with structurally well-defined PdAg/Pd(111) surface alloys was investigated by temperature-programmed desorption (TPD) and high-resolution electron energy loss spectroscopy (HREELS) to unravel and understand contributions from electronic strain, electronic ligand and geometric ensemble effects. TPD measurements indicate that CO adsorption is not possible on the Ag sites of the surface alloys (at 120 K) and that the CO binding strength on Pd sites decreases significantly with increasing Ag concentration. Comparison with previous scanning tunneling microscopy (STM) data on the distribution of Pd and Ag atoms in the surface alloy shows that this modification is mainly due to geometric ensemble effects, since Pd(3) ensembles, which are the preferred ensembles for CO adsorption on non-modified Pd(111), are no longer available on Ag-rich surfaces. Consequently, the preferred CO adsorption site changes with increasing Ag content from a Pd(3) trimer via a Pd(2) dimer to a Pd monomer, going along with a successive weakening of CO adsorption. Additionally, the CO adsorption properties of the surface alloys are also influenced by electronic ligand and strain effects, but on a lower scale. The results are discussed in comparison with previous findings on PdAg bulk alloys, supported PdAg catalysts and PdAu/Pd(111) model systems.     

Atomic-scale assembly of a heterogeneous catalytic site

The distance between surface Pd atoms has been shown to control the catalytic formation of vinyl acetate from ethylene and acetic acid by AuPd catalysts. Here, we use the bulk alloy's thermodynamic properties, as well as the surface lattice spacing of a AuPd(100) alloy single-crystal model catalyst to control and optimize the concentration of the active site (Pd atom pairs at a specific Pd-Pd distance with Au nearest-neighbors). Scanning tunneling microscopy reveals that sample annealing has a direct effect on the surface Pd arrangements: short-range order preferentially forms Pd pairs located in the c(2 x 2) sites, which are known to be optimal for vinyl acetate synthesis. This effect could be harnessed for future industrial catalyst design.     

氢和硫原子在Pd、Au和Cu及PdAu、PdCu合金(111)表面吸附的密度泛函研究

用密度泛函理论研究了氢和硫原子在金属Pd、Au、Cu以及合金PdM3、Pd2M2 和Pd3M(111)表面的吸附(M=Au, Cu), 得到了覆盖率为0.25时最稳定的吸附位、结合能以及吸附前后表面的驰豫情况. 结果表明, 氢和硫均与Pd形成最稳定的吸附, Cu次之, Au的吸附最弱, 其在三种纯金属(111)表面的最稳定吸附位均为fcc位. 由于PdAu合金具有较大的晶格常数, Pd3Au 合金吸附氢的结合能甚至较纯Pd更大, 除此之外, 氢和硫在PdM合金表面的吸附基本随M组分的增加而减弱, 而最稳定的吸附位随金属种类和组成变化而变化. 根据计算得到的吸附结合能, 发现与PdCu合金相比, PdAu合金在Au含量较低(约25%, 摩尔分数)时, 氢和硫吸附的结合能下降较慢, 而Au含量较高(跃50%)时, 结合能迅速下降, 这表明含金量为25%-50%的PdAu合金有可能在保持相近透氢性能的同时, 比PdCu合金具有更好的抗硫毒性.     

Unique activity of Pd monomers: hydrogen evolution at AuPd(111) surface alloys

Well-defined Au/Pd(111) alloy films have been prepared on a Ru(0001) substrate by electrochemical metal deposition and subsequent heating up to 700 degrees C. The electrochemical behaviour of the 20 monolayers thick epitaxially-grown films is in excellent agreement with both equilibrium surface composition and distribution for Au/Pd alloys on Mo(110) as previously reported (D. W. Goodman et al., J. Phys. Chem., 2005, B109, 18535). The electrocatalytic activity of the AuPd(111) surface alloys was studied for the hydrogen evolution in 0.1 M H(2)SO(4) as a function of surface composition. Maximum activities were found for Pd fractions of 0.2 +/- 0.1, where the population of Pd atoms surrounded by Au has its maximum. These Pd monomers are found to be about 20 times more active than Pd atoms in the Pd overlayer.