Acute toxicities of six manufactured nanomaterial suspensions to Daphnia magna

The rapid growth of nanotechnology is stimulating research on the potential environmental impacts of manufactured nanomaterials (MNMs). This paper summarizes a comprehensive study on the 48-h acute toxicity of water suspensions of six MNMs (i.e., ZnO, TiO₂, Al₂O₃, C₆₀, SWCNTs, and MWCNTs) to Daphnia magna, using immobilization and mortality as toxicological endpoints. The results show that the acute toxicities of all MNMs tested are dose dependent. The EC₅₀ values for immobilization ranged from 0.622 mg/L (ZnO NPs) to 114.357 mg/L (Al₂O₃ NPs), while the LC₅₀ values for mortality ranged from 1.511 mg/L (ZnO NPs) to 162.392 mg/L (Al₂O₃ NPs). In these tests, TiO₂, Al₂O₃, and carbon-based nanomaterials were more toxic than their bulk counterparts. Moreover, D. magna were found to ingest nanomaterials from the test solutions through feeding behaviors, which indicates that the potential ecotoxicities and environmental health effects of these MNMs cannot be neglected.     

A Novel Approach to Prepare CaCO3/Polyvinylpyrrolidone (PVP) Composite Nanofibers

A new route to prepare CaCO₃ nanoparticles/polyvinylpyrrolidone (PVP) nanofibers is reported. An aqueous solution of K₂CO₃ was added to a solution of CaCl₂/PVP, resulting in in-situ preparation of CaCO₃ nanoparticles. Then composite nanofibers containing CaCO₃ nanoparticles were successfully prepared by electrospinning. The morphology of the resulting composite nanofibers was characterized by field-emission scanning electron microscopy. In addition, the products were characterized by thermogravimetry analysis and Fourier transform infrared spectra.     

Growth, morphology and optical properties of tris(8-hydroxyquinoline)aluminum/zinc oxide hybrid nanowires

Hybrid tris(8-hydroxyquinoline)aluminum/zinc oxide (Alq₃/ZnO) nanowires were successfully grown from a one-step solution method at very low temperature. The transformation of amorphous Alq₃ into α-phase crystalline nanowires was achieved by incorporating a certain weight fraction of crystalline ZnO nanomaterials. A growth mechanism was proposed to validate the formation of crystalline Alq₃-ZnO hybrid nanowires with the help of nucleation initiated by the ZnO nanomaterials, followed by Alq₃ molecular aggregation. Effects of temperature on the evolution of morphologies of hybrid nanowires were examined by the field-emission scanning electron microscopy (FESEM). The photoluminescence (PL) spectra of hybrid nanowires showed a significant threefold enhancement in PL intensity, along with a slight blue-shift emission, when compared to the pure Alq₃ molecules, which were attributed due to the incorporation of crystalline ZnO nanomaterials and also the shielding effect of ZnO nanomaterials to avoid the excimer formation between the Alq₃ molecules in the excited state.     

Compare study CaCO3 crystals on the cellulose substrate by microwave-assisted method and ultrasound agitation method

The purposes of this article were to investigate the influences of synthesis strategy on the CaCO₃ crystals on the cellulose substrate. In this study, CaCO₃ crystals were synthesized using cellulose as matrix by the microwave-assisted method and ultrasound agitation method, respectively. The CaCO₃ crystals on the cellulose substrate were characterized by means of X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM). Experimental results demonstrated that the synthesis strategy had a dramatically influences on the phase, microstructure, morphology, thermal stability, and biological activity of the CaCO₃ crystals. The pure phase of vaterite spheres with the diameter of about 320–600 nm were obtained by ultrasound agitation method, meanwhile, the mixed phases of calcite and vaterite with the diameter of about 0.82–1.24 μm were observed by microwave-assisted method. In view of experimental results, one can conclude that the ultrasound agitation method do more favors to the synthesis of CaCO₃ crystals with uniform morphology and size, compared with microwave-assisted method. Furthermore, cytotoxicity experiments indicated that the CaCO₃ crystals on the cellulose substrate had good biocompatibility and could be a candidate for the biomedical applications.     

Spectral characterization and energy levels of Cr:Sc2(MoO4)3 crystal

This paper reports the spectral properties and energy levels of Cr³⁺:Sc₂(MoO₄)₃ crystal. The crystal field strength Dq, Racah parameter B and C were calculated to be 1408 cm⁻¹, 608 cm⁻¹ and 3054 cm⁻¹, respectively. The absorption cross sections σ_α of ⁴A₂→⁴T₁ and ⁴A₂→⁴T₂ transitions were 3.74×10⁻¹⁹ cm² at 499 nm and 3.21×10⁻¹⁹ cm² at 710 nm, respectively. The emission cross section σ_e was 375×10⁻²⁰ cm² at 880 nm. Cr³⁺:Sc₂(MoO₄)₃ crystal has a broad emission band with a broad FWHM of 176 nm (2179 cm⁻¹). Therefore, Cr³⁺:Sc₂(MoO₄)₃ crystal may be regarded as a potential tunable laser gain medium.     

Selective synthesis of monoclinic and tetragonal phase LaVO<Subscript>4</Subscript> nanorods via oxides-hydrothermal route

Pure monoclinic (m-) and tetragonal (t-) LaVO₄ nanorods are successfully obtained via a facile oxides-hydrothermal method, in which V₂O₅ and La₂O₃ bulk powders are directly utilized as precursors without pretreatment. It is found that ethylenediamine tetraacetic disodium salt (EDTA) is a key factor for synthesizing t-LaVO₄. The as-obtained products are characterized by X-ray powder diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution TEM (HRTEM), and selected area electron diffraction (SAED). The FTIR spectra of VO₄ around 800 cm⁻¹ are suggested as an effective auxiliary means to identify the crystal phase of LaVO₄. UV–Visible spectra of LaVO₄ nanomaterials are obvious blue shift compared with the bulk m-LaVO₄ materials. The different photoluminescent properties of Eu³⁺ doped m- and t-LaVO₄ are demonstrated. A dissolution–precipitation mechanism is mainly responsible for the anisotropic morphology and phase control evolution of the LaVO₄ nanocrystals. The oxides-hydrothermal system is also applicable to prepare other pure LnVO₄ (Ln³⁺: Nd³⁺, Y³⁺, Sm³⁺) and doped LnVO₄ nanomaterials.     

Hydroxyethyl cellulose-assisted hydrothermal synthesis of Bi2S3 urchin-like colonies

Orthorhombic Bi₂S₃ with different morphologies was successfully synthesized by the acid-catalyst hydrothermal reactions of bismuth nitrate (Bi(NO₃)₃) and thiourea (NH₂CSNH₂) solutions containing different amounts of hydroxyethyl cellulose (HEC). Phase, morphologies, and optical properties were characterized by X-ray diffraction, selected area electron diffraction, scanning and transmission electron microscopy, and ultraviolet-visible spectroscopy. The products, hydrothermally synthesized in the HEC-free, 0.25 g HEC-added, 0.5 g HEC-added and 1.00 g HEC-added solutions, were respectively proved to be orthorhombic Bi₂S₃ irregular nanorods, complete urchin-like colonies of regular nanorods, incomplete urchin-like colonies of regular nanorods, and highly crystalline regular nanorods growing along the [001] direction. Tauc band gaps of the orthorhombic Bi₂S₃ nanorods, synthesized in the HEC-free, 0.25 g HEC-added, and 1.00 g HEC-added solutions were determined to be 3.0, 1.75 and 1.8 eV, respectively. Formation mechanism of orthorhombic Bi₂S₃ nanorods, synthesized in the HEC-free and HEC-added solutions, was also discussed at great detail.     

High-pressure polymorphic transformation of rutile to alpha-PbO2-type TiO2 at {011}R twin boundaries

The presence of nano-scale lamellae of the α-PbO₂-type polymorph of TiO₂ sandwiched between twinned rutile inclusions in jadeite has been confirmed by electron diffraction and high-resolution transmission electron microscopy, backed up by image simulation techniques, from ultrahigh-pressure jadeite quartzite at Shuanghe in the Dabie Mountains, China. The crystal structure is orthorhombic with lattice parameters a = 4.58 Å, b = 5.42 Å, c = 5.02 Å and space group Pbcn. A three-dimensional structural model has been constructed for the rutile to α-PbO₂-type TiO₂ phase transformation based on high-resolution electron microscopic images. Computer image simulation and structural model analysis reveal that rutile {0 1 1}_R twin interface is a basic structural unit of α-PbO₂-type TiO₂. Nucleation of α-PbO₂-type TiO₂ lamellae 1–2 nm thick is caused by the displacement of one half of the titanium cations within the {0 1 1}_R twin slab. This displacement reduces the Ti–O–Ti distance and is favored by high pressure.     

Bouncing behaviors of suspension liquid drops on a superhydrophobic surface

Abstract  

This paper reveals three patterns of bouncing behaviors of suspension drops containing calcium carbonate (CaCO₃) powder on a superhydrophobic surface with the aid of a high-speed camera. In transmission electron microscopy (TEM) observation, the particles of CaCO₃ are shaped like sticks whose equivalent diameters are about 700 nm. Unlike a pure water drop, dense suspension drops cannot be pinched off at the bounce on the superhydrophobic surface due to a high effective viscosity, whereas the equilibrium contact angle appears to be almost identical in all kinds of droplets.     

Electrochemical properties of polyaniline-modified sodium vanadate nanomaterials

Sodium vanadate nanomaterials were synthesized at different pH-values of a sodium hydroxide solution of vanadium pentoxide. Polyaniline-modified sodium vanadate nanomaterials were prepared at room temperature and at 3°C by a chemical polymerization method. The crystal structure and phase purity of the samples have been examined by powder XRD. The samples were identified as HNaV₆O₁₆⋅4H₂O and Na_1.1V₃O_7.9. The electrochemical measurements show that polyaniline-modified sodium vanadate hydrated nanomaterials provide higher current density than the sodium vanadate nanomaterials.     

利用聚乙烯亚胺修饰的CaCO3仿生模板合成3D花朵型二氧化硅微球

利用聚乙烯亚胺(PEI)修饰的碳酸钙仿生模板合成了具有3D花朵型形貌的SiO₂微球.通过调整碳酸钙微粒表面不同浓度PEI的吸附量实现SiO₂微球的形貌控制呈现花朵或刀锋的形状. 用XPS和SEM对制备的SiO₂微粒进行表征. 结果表明,不用浓度的PEI修饰可以较好地控制3花朵型DSiO₂微球的形貌.     

Structural characteristics and morphology of SmxCe1−xO2−x/2 thin films

Effect of the deposition temperature (200 and 500 °C) and composition of Sm_xCe_1−xO_2−x/2 (x = 0, 10.9–15.9 mol%) thin films prepared by electron beam physical vapor deposition (EB-PVD) and Ar⁺ ion beam assisted deposition (IBAD) combined with EB-PVD on structural characteristics and morphology/microstructure was investigated. The X-ray photoelectron spectroscopy (XPS) of the surface and electron probe microanalysis (EPMA) of the bulk of the film revealed the dominant occurrence of Ce⁴⁺ oxidation state, suggesting the presence of CeO₂ phase, which was confirmed by X-ray diffraction (XRD). The Ce³⁺ oxidation states corresponding to Ce₂O₃ phase were in minority. The XRD and scanning electron microscopy (SEM) showed the polycrystalline columnar structure and a rooftop morphology of the surface. Effects of the preparation conditions (temperature, composition, IBAD) on the lattice parameter, grain size, perfection of the columnar growth and its impact on the surface morphology are analyzed and discussed.     

Influence of Lu2O3 on electrical and microstructural properties of CaCu3Ti4O12 ceramics

In this work, the influence of Lu₂O₃ doped on the dielectric and electrical properties of CaCu₃Ti₄O₁₂ was reported. Lu₂O₃-doped CCTO was prepared by a conventional solid state technique using CuO, TiO₂, and CaCO₃ as starting materials. The samples were studied by X-ray diffraction (XRD) and scanning electron microscopy (SEM); dielectric measurements were measured in the 10² Hz–10⁷ Hz frequency range at room temperature; and the nonlinear behavior of all samples was measured. The doping of Lu₂O₃ resulted in an increase in the dielectric constant of CCTO, but decreased the stability of the frequency dependence. Increasing concentrations of Lu₂O₃ resulted in decreasing nonlinear coefficients.     

Combustion synthesis of magnesium ferrite as liquid petroleum gas (LPG) sensor: Effect of sintering temperature

We report synthesis of Spinel type magnesium ferrite (MgFe₂O₄) material by a simple, inexpensive combustion method with glycine as a fuel and their application as a gas sensor for reducing gases (LPG, Acetone, Ethanol, Ammonia). The dependence of reducing gas sensing properties on the structural and surface morphological properties has been studied as an effect of sintering temperatures. The structural and surface morphological properties were studied by X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. The MgFe₂O₄ were highly oriented along (311) with the spinel type crystal structure. The SEM observation reveals that porous morphology decreases due to the grain growth as sintering temperature increases. The mechanism of reducing gas sensing by the MgFe₂O₄ pellets is explained on the basis of adsorbed oxygen on the sensor surface. The selectivity and maximum response of 71% to 2000 ppm of LPG was observed at 698 K with the (MgFe₂O₄) material sintered at 1173 K.     

Crystallization and Thermal Conductivity of CaCO3 Nanoparticle Filled Polypropylene

Isotactic polypropylene (IPP) and calcium carbonate (CaCO₃) nanocomposites were prepared by melt extrusion in a twinscrew extruder. The effect of CaCO₃ nanoparticles on the crystallization and thermal conductivity (TC) of PP was studied by thermal analysis (DSC) and thermal conductivity analysis (TCA). The introduction of CaCO₃ nanoparticles resulted in an increase in crystallinity. The incorporation of this nanoparticle (up to 15 phr) caused a significant increase of TC of PP, especially for larger filler content. Several models were used for prediction of TC of the nanocomposites. The experimental results had a good correlation with the Ce Wen Nan Model.     

Synthesis of CaCO3 Nanoparticles by Mechanochemical Processing

The synthesis of calcite (CaCO₃) nanoparticles by mechanochemical reaction and subsequent heat treatment was investigated. A solid-state displacement reaction CaCl₂ + Na₂CO₃ CaCO₃+2NaCl was induced during mechanical milling of a CaCl₂+ Na₂CO₃ powder mixture. Heat treatment of the as-milled powder at 350°C completed the reaction, forming crystalline CaCO₃ nanoparticles separated from each other in a dry-salt matrix. A simple washing process to remove the matrix yielded calcite single phase ultrafine powder. The mean particle size was controlled by changing the volume fraction of CaCO₃ in the matrix. 20% volume fraction yielded nanoparticles of ~ 140 nm in size, whereas 10% volume fraction led to ~ 80 nm size nanoparticles.     

Synthesis of VO2 (B) nanorods for Li battery application

Vanadium dioxide nanorods were synthesized through a hydrothermal reaction from V₂O₅ xerogel, poly(vinyl pyrrolidone) (PVP) and lithium perchlorate (LiClO₄). The prepared samples were characterized by X-ray diffraction, infrared spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM) and electrochemical discharge–charge cycling in lithium battery. SEM images reveal the nanorods to have dimensions on the order of 1–3 μm in length and 10–50 nm in diameter. The measured initial discharge capacity of the lithium battery with a cathode made of VO₂ (B) nanorods was 152 mA h/g.     

Large-scale synthesis and growth habit of 3-D flower-like crystal of PbTe

In this paper, 3-D flower-like crystal of PbTe was successfully synthesized using Pb(CH₃COO)₂·3H₂O and Na₂TeO₃ as precursors under hydrothermal conditions, and characterized by means of scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray diffraction pattern (XRD). The reaction parameters that influenced the evolution of PbTe synthesis and morphology were investigated. It was shown that the flower-like crystal of PbTe was composed of a nucleus with eight pods. A possible growth mechanism was proposed based on the calculation of the surface energies of PbTe and the SEM observation. Furthermore, the temperature-dependent transport properties of 3-D flower-like crystal of PbTe specimen have been evaluated with an average thermoelectric power of 120 S cm^?1 and electrical conductivity of 220 μV K^?1 at 740 K.     

Solvothermal synthesis and characterization of α-Fe2O3 nanodiscs and Mn3O4 nanoparticles with 1,10-phenanthroline

α-Fe₂O₃ nanodiscs and Mn₃O₄ nanoparticles have been prepared by the 1,10-phenanthroline as complexing agent in the presence of sodium hydroxide under hydrothermal conditions. The products were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and Fourier transform infrared (FT-IR) spectra. The average diameter of α-Fe₂O₃ nanodiscs is of 2 μm. In the case of Mn₃O₄ sample, the Mn₃O₄ crystallites are nanoparticles with an average size of 34 nm. A formation mechanism for the α-Fe₂O₃ and Mn₃O₄ nanomaterials was proposed.     

Novel nanostructures of β-Ga2O3 synthesized by thermal evaporation

In this study, we report the novel β-Ga₂O₃ nanostructures synthesized by the thermal evaporation of Ga droplet in the presence of Au catalysts at 900 °C. The morphology and structure of the products were analyzed by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray diffraction (XRD). The single-crystalline β-Ga₂O₃ nanosheets have lateral dimensions up to several tens of microns. Large arrays of column-like layered crystal β-Ga₂O₃ structures that consisted of many nanosheets were formed on the Au-coated silicon substrate under the suitable vapor concentration. These novel β-Ga₂O₃ nanostructures are expected to have potential application in functional nanodevices.