Spectrophotometric and gravimetric determination of sulfur in sebacate-base lubricants

Sulfur is determined in sebacate-base lubricants spectrophotometrically and gravimetrically. In the spectrophotometric method, a 0.2–0.3-g sample is treated with mixed acids, magnesium chloride is added, and the solution is evaporated to dryness. The sulfate is reduced to hydrogen sulfide by treatment with a mixture of hydriodic. hypophosphorous, and hydrochloric acids, and the hydrogen sulfide is distilled into ammonia solution. Lead citrate reagent is added and the brownish yellow color of lead sulfide sol is measured. An improved technique and apparatus for the distillation is described. In the gravimetric method, a 5-g sample is treated with mixed acids, antimony and tin are volatilized by treatment with hydrobromic acid, and sulfur is precipitated as barium sulfate. The recommended range of the spectrophotometric method is 0.005–0.15%,and that of the gravimetric method is 0.01–1% sulfur.     

Determination of free, total, and esterified cholesterol by high-performance liquid chromatography

A method is described for measuring free, total, and esterified cholesterol in blood serum in which reversed-phase liquid chromatography is used and the eluate is monitored at 200 nm. The sample for total cholesterol is prepared according to the Abell-Kendall procedure, and for free cholesterol an extract of serum--isopropanol (1:5, v/v) is used. The column is a muBondapak C18, 10 micrometers, and the mobile phase for total cholesterol is isopropanol--acetonitrile (50:50, v/v); for free cholesterol, it is isopropanol--acetonitrile--water (60:30:10). An approximation of the free cholesterol, triglycerides, and individual cholesteryl esters is obtained from single chromatograms of isopropanol extracts of serum if the first mobile phase is used. In a comparison study with the Abell-Kendall method for total cholesterol, the correlation is excellent and the precision is acceptable.     

水性聚氨酯的制备及其性能的研究

本文以琥珀酸酐与三羟甲基丙烷反应,制得了含有羟基和羧基的酯类亲水性单体,并以此单体与ＴＤＩ和ＰＰＧ－１０００反应,制得了含有羧基的聚氨酯预聚体,在三乙醇胺水溶液中分散得到了水性聚氨酯（简称ＷＰＵ）。本文对预聚体的溶剂种类和用量,对乳胶粒的大小及形状的影响进行了研究,确认溶剂的用量越大,乳胶的粒径就越小;以丙酮作溶剂,乳胶粒为棒状或橄榄球状,而以丁酮为溶剂,得到的乳胶粒为圆球状。通过改变亲水单体的用     

D241树脂分离纯化黄芩总黄酮的研究

本文研究了用241树脂分离纯化黄芩总黄酮的方法和工艺。实验结果表明：D241树脂对黄芩总黄酮的静态交换容量是77mg/ml树脂。在pH11.0、流速2.0BV/h、提取液中总黄酮浓度17.5mg/ml条件下，D241树脂对黄芩总黄酮的动态交换容量为43.8mg/ml。用60％甲醇作为黄芩总黄酮洗脱剂，在PH4.0、洗脱流速1.5BV/h条件下，4．5BV洗脱剂即可完全洗脱被D241树脂交换的黄芩总黄酮。与酸沉淀法相比较，经过除去果胶，总黄酮纯度由33．34％提高到74．9％，粗品收得率由11.52%降低至4.83%；经过D241树脂分离纯化，其纯度达到91.5%，产品收得率3.54%。     

用计算全息法检测卡塞格林系统主镜

为实现对卡塞格林光学系统中的非球面主镜表面面形的高精度检测,设计了一种二元位相型计算全息图(CGH)。介绍了工作原理,对CGH的相位模型参数的优化设计、衍射次级分离以及台阶位置与深度计算等关键问题进行了讨论。通过引入虚拟玻璃的概念快速建立非球面检测模型,针对卡塞格林系统主镜中心开孔的特点,通过加入同轴载波实现了衍射次级的完全分离,相比目前常用的倾斜载波方法简化了相位量化复杂度,数值仿真计算出了最优的台阶深度,降低了加工难度。给出了相应的设计方法及实例,研制投产了CGH。测试得到主镜面形的均方根误差为0.018λ,并与传统补偿器结果(RMS=0.019λ)进行对比,两者测试结果吻合,验证了该设计与检测方法的正确性,该设计方法简单快捷,适用于卡塞格林光学系统主镜面形检测。     

聚苯胺薄膜电极上示差脉冲伏安法可逆波理论研究

本文提出了聚苯胺(PANI)薄膜电极上示差脉冲伏安法可逆波理论,经验证理论和实验结果相符合.     

山东省主栽果树生殖器官中稀土与微量营养元素的相关性研究

通过对山东省5大类主栽果树20余个树种的花粉、种子和果实稀土与微量元素自然含量进行分析比较, 认为稀土(RE)与微量元素在各树种花粉中平均含量顺序为Fe＞Zn＞B＞Cu＞Mn＞RE, 种子中B＞Fe＞Zn＞Mn＞Cu＞RE, 果实中Fe＞B＞Zn＞Cu＞Mn＞RE. 各元素在各生殖器官中的自然分布因树种而有很大差异. 但基本规律类同, 即花粉＞种子＞果实. 花粉富集各种微量营养元素的能力都很强. 花粉和果实稀土与微量元素之间绝大多数呈正相关, 种子大多呈负相关, 但相关性均不显著.     

Spectrophotometric determination of pentaerythritol tetranitrate (PETN) in waste water from lead styphnate primer plants

An accurate spectrophotometric method is proposed for the determination of pentaerythritol tetranitrate (PETN) in waste water from lead styphnate primer plants by use of phenoldisulphonic acid. The waste water is filtered through a sintered glass crucible and the PETN is determined in the filtrate and the residue. In the determination of PETN in the filtrate, sodium hydroxide is added and the PETN is extracted with methylene chloride (in alkaline solution, styphnate and TNT are not extracted). The methylene chloride solution is then evaporated to dryness, the residue is treated with a solution of phenoldisulphonic acid in sulphuric acid, water and ammonia are added, and the yellow colour is measured. In the determination of PETN in the residue, the PETN is dissolved in acetone, an aliquot of the acetone solution is treated with water and sodium hydroxide, the PETN is extracted with methylene chloride and the colour is developed as above. Various factors affecting the determination were investigated. The solubility of PETN in water was studied.     

微波消解-ICP-MS测定电镀污泥中的重金属

采用微波消解系统对某电镀污泥进行消解,利用ICP-MS对污泥中的重金属进行测定。称取制备后样品,置于消解罐中充分反应后,赶酸、定容后利用电感耦合等离子体质谱法进行测定。电镀污泥中的铬为18845.2mg/kg、镉为10.3mg/kg、镍为5200.0mg/kg、铅为189.7mg/kg、铜为3271.7mg/kg、锌为49632.6mg/kg。测定结果表明所检测项目工作曲线线性关系好,相关系数r均大于0.999。铬加标回收率在91.6～97.7%之间、镉加标回收率在92.0～97.0%之间、镍加标回收率在95.1～98.0%之间、铅加标回收率在94.3～95.2%之间、铜加标回收率在97.1～102%之间、锌加标回收率在96.3～98.7%之间,均满足相关测定要求。计算的潜在生态危害系数、潜在生态危害指数结果表明,电镀污泥中的铬、镉、铅、铜、锌为轻微生态危害,镍为强生态危害;潜在生态危害指数RI计算值为216.69,属于中等生态危害。     

响应面法优化巴旦木壳对废水Pb、Cu和Cd的吸附及同时测定

研究废弃巴旦木壳对模拟废水中Pb、Cu和Cd的去除率。在单因素试验的基础上,采用响应面法对吸附剂投加量、吸附时间和pH值3因素进行优化。实验结果表明,最佳吸附条件为Pb：为吸附剂投加量0.4g、吸附时间49.38min、pH值为9.96;Cu：吸附剂投加量0.4g、吸附时间49.91min、pH值为10.13;Cd：吸附剂投加量0.4g、吸附时间49.83min、pH值为10.42;在此条件下,Pb、Cu和Cd的去除率分别为87.42%、73.49%和85.11%。采用偏最小二乘法(PLS)对Pb、Cu和Cd模拟混合试样吸附后的溶液进行同时测定,计算得出吸附剂对Pb、Cu和Cd的去除率分别为83.2%、66.0%和83.3%。     

Wastewater treatment using nanomaterial quaternary photocatalyst ZrCdPbO4 - Removal of colour pollutant by an eco friendly process

Pollution of environment is a major issue and has drawn attention of researchers throughout the globe. Water is polluted by various means like excretion of various industries and house releases, for example release of yarn, paper, and cloth industries etc. Present investigation consists of removal of such a pollutant. For this, synthesis of a novel quaternary nano particle sized photocatalyst ZrCdPbO₄ is carried and its characterization by different analytical techniques is also carried out. This is further used for removal of colour pollutants from the environment and Erythrosine-B is considered as a role model. Effect of various operational parameters like pH, concentration of dye, amount of photocatalyst, irradiation power etc. is studied, maximum degradation condition is extracted, and it is observed that reaction follows pseudo first order kinetics. Scavenger study suggests the participation of OH free radical in the reaction. Complete degradation of the dye in presence of light and photocatalyst is reported here by. Reusability of the photocatalyst is tested and is found to work up to five cycles efficiently.     

Polymers for Enhanced Oil Recovery Technology

Recently enhance oil recovery (EOR) technology is getting more attention by many countries since energy crises are getting worse and frightened. One of the reasons for this is due to the shortage of current oil resources and difficulties in finding a new oil field. Indonesia is one of the examples, before 2004 Indonesia is a net oil exporting country but after that Indonesia is a net oil importing country. The oil demand in the country is increasing while the oil production capacity is decreasing. In fact, when a new oil reservoir is drilled, the oil amount obtained from it is about 20-40% of the potential and hence there is still 60-80% oil left in the reservoir. Application of EOR technology gives an additional chance to get out more oil from the reservoir, possibly about another 20%. Polymer is the material that plays an important role in the application of EOR technology, especially surfactant and hydrogel polymers. In the technology, surfactant polymer is injected to the reservoir to reduce an interfacial tension between oil and water and is able to wipe out the trapped oil from the reservoir rock and hence increase the oil production. While an injection of hydrogel polymer to the reservoir is to increase a viscosity of fluid containing water so that the fluid is more difficult to flow than the oil, and as a result, the oil production increases. The most common polymer used for this application is polyacrylamide group.     

Membrane oxygen enrichment : II. Economic assessment

The classic membrane gas-separation process that virtually everyone doing membrane research has considered, and many have worked on, is oxygen enrichment of air. There seems to be an almost emotional appeal for membrane oxygen enrichment, perhaps because air is free and the market for oxygen is huge. This paper is an attempt to add some facts to the appeal. The state-of-the-art of membrane oxygen enrichment is analyzed, and the authors' opinions of where the leverage for improvement is, and is not, are presented.     

N,O-羧甲基壳聚糖的合成和性质研究

采用多段升温法将壳聚糖改性,合成了取代度为1.84、平均分子量为3.08×105、等电点为7.28的N,O-羧甲基壳聚糖(CMC),分别用紫外光谱、红外光谱、荧光光谱对其结构进行了表征,并对其水溶液的Zeta电位、电导率、表面张力以及水分散体系中羧甲基壳聚糖微粒的粒径分布进行了研究.结果表明, N,O-羧甲基壳聚糖具有表面活性;介质的pH值和浓度对羧甲基壳聚糖溶液的稳定性有很大的影响.     

Prospective study to assess the clinical efficacy of bone scintigraphy--some analyses of clinical data

The value of preoperative bone scans in patients with primary breast and prostate cancer was evaluated prospectively. Of 414 patients with breast cancer, clinical stage I is 14, II is 219, IIIA is 59, IIIB is 39 and IV is 14. Of 88 patients with prostate cancer, clinical stage I is 14, II is 15, III is 18 and IV is 41. 11 percent of patients with breast cancer and 54 percent of patients with prostate cancer had bone metastases. Clavicle, ribs, thoracic spine, lumbar spine and pelvis metastasized most frequently. The incidences of bone metastases were 18.4% with Scirrhous carcinoma, 15.4% with Medullary tubular carcinoma and 3.8% with Papillotubular carcinoma. The methodology and results of ROC analysis were described in our other papers. Some results of data analysis were described in this paper.     

Design of YCF-1 mobile γ irradiator

YCF-1 Mobile irradiator is designed by BINE of China. It has been put into running in YanJi city of Jilin province. It is able to be moved to border and distance places and area lumped and spreading out of agricultural products to service. It can play a important role in demonstration and extending irradiation technology in food irradiation, disinfestation, sterilization and quarantine, etc. This paper describes the features and design considerations of mobile irradiator.This irradiator adopted Cesium-137 source. The design capacity of loading source is 9.25PBq (250kCi), A half-time of Cs- 137 is 30.2 years long, exchanging source is not needed utilization rate of energy is higher, and the shielding is thinner, The Weight is lighter, The dose rate on the surface of it is 0.0025mSv/h in accordance with national standard. The internal size of irradiation room is 1800×1800×900mm (L×W×H), The sheilding of irradiation room is a steel shell filled with lead. The thickness of lead is 18cm. The irradiator is installed on a special flat truck. The size of the truck is 7000×3400×4200mm (L×W×H). The weight of irradiator is more than 80 150kw. The main components and parts of irradiator are: source, source racks and hoist, irradiation chamber, storage source chamber, the product's transport system, dose monitoring system, ventilation system and safety interlock system, etc.     

Chronoamperometric current at finite disk electrodes

The chronoamperometric current at a stationary finite disk electrode is studied using both analytical and digital simulation techniques. The exact long-time expansion of the current is obtained and its short-time behavior is considered. Digital simulation of the current using an explicit hopscotch algorithm is presented. In contrast to the usual explicit difference method, the ‘hopscotch’ algorithm is unconditionally stable, and thus, it is particularly suited for studying electrochemical problems at intermediate and long times. A simple analytic expressions for the current, which is accurate to 0.6% for all times, is presented.     

离心系数表征丙烯酰胺反相乳液的稳定性

用丙烯酰胺反相乳液经离心处理后保留的乳液体积与原乳液体积之比（离心系数Vr）考察了丙烯酰胺及其衍生物反相乳液的稳定性。 结果表明,离心系数Vr越大,其乳液的稳定性越好。 在高速离心条件下,由Span80/Span85和Tween80构成的丙烯酰胺及其衍生物反相乳液的Vr与油相质量分数存在正相关的关系。 在油相质量分数确定的情况下,离心系数Vr不仅与3种表面活性剂构成的亲水亲油平衡值（HLB）有关,而且与丙烯酰胺及其衍生物的浓度和类型有关。 HLB值在4.20左右时,乳液是稳定的;随丙烯酸氧乙基三甲基氯化铵（DAC）在水相中质量分数的提高,反相乳液稳定性增强,w(DAC)＞24%时可得到稳定乳液。 在15000 r/min离心3 min,Vr=0.95以上的丙烯酰胺及其衍生物反相乳液很稳定,静置半年仍未出现分层现象。     

Adsorption and structure of hydrocarbons in MCM-41: a computational study

The adsorption of linear, branched, and cyclic hydrocarbons in MCM-41 is studied using Configurational Bias Monte Carlo simulations. A new computational model for MCM-41 is proposed which, although simple, is able to predict adsorption isotherms which are in agreement with the scarce experimental data. The structure of the adsorbed phase is analyzed and found to be similar to that of studies using small, hard spheres trapped in pores. The adsorption of mixtures is investigated, and the adsorption hierarchy is discussed. The structure of the adsorbed mixture is revealed and shows that all components of the mixture exhibit structure, even if they are only adsorbed in small quantities. Finally, the model is modified to include surface roughness and the effect on the adsorption isotherms and structure of the adsorbed phase is discussed.     

尿激酶活性测定方法的比较

根据中国及日本药典,对测定尿激酶活性的两种方法的灵敏度和重复性进行了考察对比,对不同样品测定结果进行了比较。