聚乙二醇掺杂对氧化镍-氧化钛薄膜电致变色行为的影响

以醋酸镍、钛酸正丁酯为前驱物,聚乙二醇(PEG)为掺杂剂,制备了氧化镍-氧化钛(Ni O-Ti O2)的溶胶、干凝胶和薄膜,研究了掺杂分子量分别为200、400、1000、2000的PEG对Ni O-Ti O2薄膜电化学和光学性能的影响。对溶胶进行粒径和粘度测定,考察了干凝胶的热力学行为。溶胶在基底上浸渍提拉成膜,300℃煅烧后,采用双电位阶跃计时电流法测定Ni O-Ti O2薄膜电化学性能,分光光度计测定薄膜的透过率。其中掺杂PEG200的薄膜性能最好:其双层膜的注入电量是未掺杂单层膜的2.2倍,薄膜在550nm处着色态和无色态的透过率差值最大为54%,变色效率达到37.4cm2·C-1;掺杂PEG200可延长薄膜的循环寿命至2000圈以上。     

镍负载量对乙醇水蒸气重整制氢催化性能和催化剂的影响

采用稳态实验对镍负载量对Ni/MgO催化剂在乙醇水蒸气重整反应的影响进行了研究。结果表明，在101.3kPa下，镍负载量越高，催化剂的活性越高。对于催化剂的选择性，存在一个最佳镍负载量为10%Ni/MgO。按选择性从大到小排序，不同镍负载量的催化剂为：10Ni/MgO>15Ni/MgO>12.5Ni/MgO>7.5Ni/MgO≈5Ni/MgO。热分析表明，焙烧过程中不同镍负载量的催化剂镍前体与载体前体之间发生的相互作用不同。XRD和TPR 表征结果显示，催化剂的晶体结构和还原特性也与催化剂上镍的负载量有关。焙烧过程中样品10Ni/MgO上镍前体与载体前体发生了两种相互作用, 并且其氧化态与其他催化剂相比具有特殊的结构和还原性。说明催化剂的选择性不仅受活性相Ni的影响而且受Ni活性相周围环境的影响。     

PEO掺杂氧化镍薄膜的溶胶-凝胶法制备及电致变色性能研究

以无水醋酸镍、乙醇为前驱液, 加入适量正丁醇及PEO2000等为稳定剂, 采用改进的溶胶-凝胶法制备了稳定的PEO2000纳米Ni(OH)₂复合溶胶体系, 采用旋涂法在ITO (In₂O₃∶Sn)导电玻璃上形成均匀的氧化镍薄膜. 研究了溶胶组分对成膜性能的影响, 采用TG-DSC分析、X射线衍射仪和扫描电镜, 研究了热处理过程中的结构变化和表面形貌. 循环伏安和可见光透过率测试表明该氧化镍薄膜具有良好的电致变色性能和阳极着色效应.     

金属离子掺杂氢氧化镍的制备、结构与电化学性能

1引言： Ni（OH）2已被广泛用作镍基碱性二次电池的正极材料、电容器的电极材料、催化剂、电解剂和离子交换剂。Ni（OH）2具有仅相和B相两种晶格形态，它们在充电时会分别转化为γ-NiOOH和β-NiOOH。α-Ni（OH）2由于其具有较高的平均氧化价态（接近3．67），因而具有较高的理论比容量（482mAh／g），     

利用CO作为分子探针考察Ni-Al_2O_3间的相互作用

为了考察Ni-Al_2O_3间的相互作用,研究了CO在Ni/Al_2O_3催化剂上的吸附态红外光谱。结果表明,镍和氧化镍可以同Al_2O_3上的羟基生成NiAl_2O_4。对还原后的样品,高温真空处理可大大加速这种Ni-Al_2O_3的相互作用。同时,在表面上分散的部份镍可以向体相扩散,生成低价态的铝镍杂多酸盐。加入La_2O_3等碱性氧化物,可抑制Ni与Al_2O_3间相互作用,同时增大镍分散度和稳定性,有利于提高Ni/Al_2O_3催化剂的催化活性和热稳定性。     

Co对NiOxHy薄膜电致变色性能的影响

本文利用阴极化电沉积法在抛光镍极及ＩＴＯ玻璃表面制备了含Ｃｏ量为１６．２％的ＮｉＯｘＨｙ薄膜,薄膜厚度分别为４２ｎｍ、２１ｎｍ,采用透射光谱以及线性电位扫描、交流阻抗和阳极稳态极化曲线等测试技术,考察了Ｃｏ对ＮｉＯｘＨｙ薄膜电致变色性能的影响,光谱测试范围为３００￣２５００ｎｍ。结果发现：Ｃｏ能降低薄膜着色态在可见光区及部分近红外区的透过率,通过电压调节不仅可以调光而且可望能够控温;同时Ｃｏ还能降     

纳米二氧化硅对镍电沉积影响及在复合镀层中的化学键合状态

用线性扫描伏安法和电位阶跃法研究了n-SiO2/Ni复合电刷镀体系的电化学响应,探讨了纳米颗粒的影响;用X射线光电子谱研究了复合镀层中n-SiO2/Ni颗粒表面与基质金属间的相互作用．结果表明纳米颗粒使金属沉积过电位显著降低,电流效率、金属成核率及晶体生长速度增加,纳米颗粒对金属镍电结晶有明显的催化效应;n-SiO2/Ni表面氧的不饱和化学键与表面扩散过程中吸附态金属Ni原子键合形成Ni-O键,纳米颗粒与基质镍以化学键方式结合．     

天然气-二氧化碳-水蒸气-氧转化制合成气的研究: 稀土助剂的作用

 研究了稀土氧化物（CeO2和La2O3）改性的镍基催化剂中助剂的\r\n作用，并考察了催化剂对天然气－二氧化碳－水蒸气－氧转化制合成气\r\n反应的活性．结果表明，La2O3改性的镍基催化剂具有较高的CH4转化率\r\n和H2选择性；经CeO2改性的镍基催化剂具有较高的CO选择性．量子化学\r\n计算和XRD研究结果表明，La2O3助剂的加入，可使还原后催化剂表面N\r\ni（111）晶面衍射峰的强度减小，较好地符合吸附活化CH4分子的“尺\r\n寸效应”和能量要求．添加CeO2助剂的催化剂，其Ni（111）晶面衍射\r\n峰强度较大，而Ni（110）晶面含量最小，不利于CH4的离解．同时，助\r\n剂RE2O3（尤其是CeO2）和MgO提高了Ni的d电子密度，因而一定程度上\r\n加强了Nid电子向CO2空反键π轨道的迁移，促进CO2分子的活化，提高\r\n其消碳活性．     

退火前后镍钨硼合金电沉积层的结构与性能

采用电化学技术、XPS、DSC、XRD等方法研究Ni W B合金电沉积及热处理前后合金镀层的结构和显微硬度.结果表明,在Ni W B合金电沉积过程中伴随着化学沉积镍等过程以及Na2B4O7在镀层中的夹杂;Ni W和Ni W B合金电沉积层分别表现为纳米晶结构和非晶态结构;热处理过程中合金电沉积层发生晶粒粗化过程以及Ni W B合金镀层发生新相形成过程,产生Ni4W和镍硼化物如Ni2B、Ni3B等沉淀物;400 ℃热处理2 h后Ni W合金镀层有最大的显微硬度达919.8 kg•mm－2,而在500 ℃下Ni W B合金有最大的硬度达1132.2 kg•mm－2.     

硫化态NiW/Al2O3催化剂加氢脱硫活性相的研究Ⅱ.程序升温还原表征

 采用程序升温还原法对一系列具有相同W含量和不同Ni含量的硫化态NiW/Al2O3催化剂进行了表征,以考察催化剂中不同硫物种的数量及还原性能. 结果表明,含有助剂Ni的催化剂TPR谱在673~873 K出现了一个还原峰,归属为催化剂的NiWS混合相被分解生成的硫化镍物的还原. 随着助剂Ni含量的增加,与该还原峰相应的H2S生成量增大,表明形成了更多的NiWS活性相. 另外,Ni/(Ni+W)原子比为0.41的催化剂样品的噻吩加氢脱硫活性随着还原温度的升高而急剧下降,证实了催化剂在还原过程中活性相被逐步分解.     

碱性Al-H_2O_2半燃料电池Au/Ni阴极性能研究

以泡沫镍为基体,AuCl3为沉积液,应用快速自沉积法制备了泡沫镍负载的纳米Au/Ni电极.电化学方法测定AuCl3溶液的浓度和沉积时间对Au粒子的尺寸和分布以及以该电极作为Al-H2O2半燃料电池阴极对H2O2性能的影响.实验表明,泡沫镍经2mmol·L-1AuCl3溶液浸渍60s后,其表面完全被粒径小于100nm的Au粒子覆盖;以其为阴极的Al-H2O2半燃料电池,在0.4mol·L-1H2O2溶液中峰值功率达135mW·cm-2.     

Electrochromism of NiO-TiO2 sol gel layers

Films of NiO-TiO₂ with Ni concentration of 100, 90, 87, 83, 75, 66, 50 and 33 mol% have been obtained via the sol-gel route by dip coating technique and sintered in air between 250 and 500°C using ethanolic sols of nickel acetate tetrahydrate (Ni(CH₃COO)₂·4H₂O) and titanium n-propoxide (Ti(O-CH(CH₃)₂)₄) precursors. Xerogels obtai- ned by drying the sols have been studied up to 900°C by thermal analysis (DTA/TG) coupled to mass and IR spectroscopy. The crystalline structure and morphology of the layers in the as deposited, bleached and colored states were determined by X-ray diffractometry, scanning electron microscopy and transmission electron microscopy Their electrochromic properties have been studied in 1 M KOH aqueous electrolyte as a function of the layer composition, thickness and sintering temperature. Deep brown colour with reversible transmittance changes have been obtained using cycling voltammetry and chronoamperometry processes. The best composition to get stable sols, a high reversible transmittance change and fast switching times (<10 s) was obtained with double NiO-TiO₂ layers 160 nm thick having 75% Ni molar concentration, and sintered between 300 and 350°C. The mechanism of coloration and morphology transformation of the layer during cycling are discussed in terms of an activation and degradation period. The results are in agreement with the accepted Bode model.     

Spontaneous magnetization in Ni-Al and Ni-Fe layered double hydroxides

Layered double hydroxides containing paramagnetic Ni (II) and diamagnetic/paramagnetic Al (III)/Fe (III) ions have been prepared and characterized. Ni 2Al(OH) 6(NO 3). nH 2O ( 1), Ni 2Fe(OH) 6(NO 3). nH 2O ( 2), Ni 2Fe(OH) 6(C 6H 8O 4) 0.5. nH 2O ( 3), and Ni 2Fe(OH) 6(C 10H 16O 4) 0.5. nH 2O ( 4) were prepared by coprecipitation at controlled pH as polycrystalline materials with the typical brucite-like structure, with alternating layers of hydroxide and the corresponding anions, which determine the interlayer separation. Magnetic studies show the appearance of spontaneous magnetization between 2 and 15 K for these compounds. Interestingly, the onset temperature for spontaneous magnetization follows a direct relationship with interlayer separation, since this is the only magnetic difference between compounds 2, 3, and 4. Magnetic and calorimetric data indicate that long-range magnetic ordering is not occurring in any of these materials, but rather a freezing of the magnetic system in 3D due to the magnetic disorder and competing intra- and interlayer interactions. Thus, these hydrotalcite-like magnetic materials can be regarded as spin glasses.     

Sugarcane bagasse cellulose fibres and their hydrous niobium phosphate composites: synthesis and characterization by XPS,XRD and SEM

Cellulose fibres obtained from sugarcane bagasse were submitted to a purification process, which consisted of an acid hydrolysis for elimination of the major part of lignin and hemicellulose. This was followed by a delignification process carried out in two steps to yield crude cellulose (CCell) fibres in the first one and with a subsequent bleaching in order to yield bleached cellulose fibres (BCell). Composites of crude and bleached cellulose fibres with hydrous niobium phosphate, cell/NbOPO₄·nH₂O, were subsequently synthesized. Scanning electron microscopy, X-ray photoelectron spectroscopy and X-ray diffraction characterization of the obtained materials showed CCell/NbOPO₄·nH₂O and BCell/NbOPO₄·nH₂O are real composites. The nature of the cellulose (CCell or BCell) has an important role on the composites obtained, namely on the niobium salt composition at the composite surface. The synthesis of membranes of both cellulose and mixed matrix cellulose/NbOPO₄·nH₂O was only possible when the bleached cellulose was used.     

α-Al2O3纳米粒子对Co-Ni合金异常共沉积电化学行为的影响

为了研究在电化学复合共沉积过程中,惰性纳米粒子和金属离子、电极表面的相互作用,以及由此产生的对合金电化学共沉积行为的影响.本文从两个吸附过程出发: 电解液中的金属离子和H＋在纳米粒子表面的吸附；纳米粒子迁移到阴极表面,在电极表面的吸附.采用Zeta电势和稳态极化以及电化学交流阻抗（EIS）研究了纳米Al2O3粒子和电解液中的金属离子，和电极表面的相互作用,进而分析了纳米粒子对Co2＋和Ni2＋还原沉积的影响规律.通过对阻抗数据的拟合,讨论了Al2O3纳米粒子对等效电路中各物理参数的影响.在H＋和不同金属离子在纳米粒子上发生竞争吸附的基础上,提出了纳米粒子和合金共沉积的可能反应历程.     

Redox-induced solid-solid phase transformation of TCNQ microcrystals into semiconducting Ni[TCNQ]2(H2O)2 nanowire (flowerlike) architectures: a combined voltammetric, spectroscopic, and microscopic study

The facile solid-solid phase transformation of TCNQ microcrystals into semiconducting and magnetic Ni[TCNQ]2(H2O)2 nanowire (flowerlike) architectures is achieved by reduction of TCNQ-modified electrodes in the presence of Ni2+(aq)-containing electrolytes. Voltammetric probing revealed that the chemically reversible TCNQ/Ni[TCNQ]2(H2O)2 conversion process is essentially independent of electrode material and the identity of nickel counteranion but is significantly dependent on scan rate, Ni2+(aq) electrolyte concentration, and the method of solid TCNQ immobilization (drop casting or mechanical attachment). Data analyzed from cyclic voltammetric and double-potential step chronoamperometric experiments are consistent with formation of the Ni[TCNQ]2(H2O)2 complex via a rate-determining nucleation/growth process that involves incorporation of Ni2+(aq) ions into the reduced TCNQ crystal lattice at the triple phase TCNQ|electrode|electrolyte interface. The reoxidation process, which includes the conversion of solid Ni[TCNQ]2(H2O)2 back to TCNQ0 crystals, is also controlled by nucleation/growth kinetics. The overall redox process associated with this chemically reversible solid-solid transformation, therefore, is described by the equation: TCNQ0(S) + 2e- + Ni2+(aq)+ 2 H2O <==> {Ni[TCNQ]2(H2O)2}(S). SEM monitoring of the changes that accompany the TCNQ/Ni[TCNQ]2(H2O)2 transformation revealed that the morphology and crystal size of electrochemically generated Ni[TCNQ]2(H2O)2 are substantially different from those of parent TCNQ crystals. Importantly, the morphology of Ni[TCNQ]2(H2O)2 can be selectively manipulated to produce either 1-D/2-D nanowires or 3-D flowerlike architectures via careful control over the experimental parameters used to accomplish the solid-solid phase interconversion process.     

氧在C－Ni（100）表面反应动力学的研究──Ⅰ．势能面特征

采用改进的ＬＥＰＳ势，通过求解广义本征方程计算了Ｏ２＋Ｃ－Ｎｉ（１００）表面反应的势能面．在碳原子被吸附于Ｎｉ（１００）表面的情况下，氧分子以不同的方式接近表面，通过势能面的计算以了解表面吸附原子与气相分子的反应途径与机理．     

Adsorption and dissociation of H2O2 on Pt and Pt-alloy clusters and surfaces

The adsorption of H(2)O(2) on Pt and Pt-M alloys, where M is Cr, Co, or Ni, is investigated using density functional theory. Binding energies calculated with a hybrid DFT functional (B3PW91) are in the range of -0.71 to -0.88 eV for H(2)O(2) adsorbed with one of the oxygen atoms on top Pt positions of Pt(3), Pt(2)M, and PtM(2), and enhanced values in the range of -0.81 to -1.09 eV are found on top Ni and Co sites of the Pt(2)M clusters. Adsorption on top sites of Pt(10) yields a weaker binding of -0.48 eV, whereas on periodic Pt(111) and Pt(3)Co(111) surfaces, H(2)O(2) generally dissociates into two OH radicals. On the other hand, attempts to attach H(2)O(2) on bridge sites cause spontaneous dissociation of H(2)O(2) into two adsorbed OH radicals, suggesting that stable adsorptions on bridge sites are not possible for any of the clusters or extended surfaces that are being studied. We also found that the water-H(2)O(2) interaction reduces the strength of the adsorption of H(2)O(2) on these clusters and surfaces.     

云南褐煤蜡氧化精制的研究

本工作对云南潦浒、寻甸、昭通蒙旦蜡进行了脱树脂,氧化精制研究,探索国产蒙旦蜡能否经精制后满足合成改性浅色蜡的要求。实验结果表明,潦浒、寻甸两厂生产的蒙旦蜡经氧化精制不能达到完全脱色,而昭通蒙旦蜡在相同的精制条件下极易脱色,所得浅色蜡质量达到和超过国外同类产品的水平,因此昭通蒙旦蜡是生产浅色蜡的理想原料。在精制反应中,加入适量ＹＰＳＯ－１添加剂,对改善反应条件,产物的分离,提高得率和质量均有良好的影响。文中还讨论了潦浒、寻甸脱脂蜡经氧化精制不能完全脱色的原因     

Coordination-driven self-assembly of a novel carbonato-bridged heteromolecular neutral nickel(II) triangle by atmospheric CO2 fixation

Formation of a quasi-symmetrical mu 3-carbonato-bridged self-assembled heteromolecular triangle of Ni(II), [(mu 3-CO 3){Ni 2(salmeNH) 2(NCS) 2}{Ni(salmeNH 2) 2].Et 2O.H 2O (HsalmeNH = 2-[(3-methylamino-propylimino)-methyl]-phenol) involves atmospheric CO 2 uptake in a neutral medium, by spontaneous self-reorganization of the starting mononuclear Ni(II)-Schiff-base complex, [Ni(salmeNH) 2]. The environment around Ni(II) in two of the subunits is different from the third one. The starting complex, [Ni(salmeNH) 2], and one of the possible intermediate species, [Ni(salmeNH 2) 2(NCS) 2], which has a very similar coordination environment to that in the third Ni(II) center, have been characterized structurally. A plausible mechanism for the formation of such a triangle has also been proposed. The compound shows a very strong antiferromagnetic coupling. Fit as a regular triangular arrangement gave J = -53.1, g = 2.24, and R = 1.5 x 10 (-4).