胶束在线扫集毛细管电泳法测定三聚氰胺

研究胶束在线扫集毛细管电泳法测定三聚氰胺的可行性,结果表明,与区带毛细管电泳相比,胶束在线扫集毛细管电泳法富集倍数提高约60倍。缓冲体系为140 mmol/L SDS+20 mmol/L NaH2PO4(pH 2.20)+10%(体积分数)甲醇,分离电压-18 kV,进样时间30 s,测量波长214 nm。考察了SDS浓度、pH、进样时间、运行电压等因素对分离测定的影响情况。在优化条件下,三聚氰胺在9 min时出峰,峰面积RSD≤3.7%。方法检出限、线性范围、相关系数分别为:0.13μg/mL、0.50~32.0μg/mL、0.9997。方法可用于奶粉中三聚氰胺的分离测定。     

Separation of naturally occurring triterpenoidal saponins by capillary zone electrophoresis.

A high-performance capillary electrophoresis (HPCE) was successfully applied to the separation and quantitation of naturally occurring oleanene triterpenoidal saponins. The HPCE adapted to the separation of two pairs of disteriomeric saponins (1-2) or (3-4), obtained from Trifolium alexandrinum seeds, was based on capillary zone electrophoresis (CZE) in borate buffer with UV detection at 195 nm. An usual technique for isolation and group separation of saponins was developed as an appropriate purification step prior to determination of individual saponins by CZE. The separation parameters such as borate concentration, pH and applied voltage were varied in order to find the best compromise that complied with demands for high separation, short duration and sufficiently high detector response. The optimum running conditions were found to be 60 mM borate buffer, pH 10 and 12 kV. Under the alkaline borate electrolyte, no resolution was achieved for the saponins (1 and 3) or (2 and 4) in a single mixture, except when 20 mM beta-cyclodextrin was added to the running electrolyte. With the combined techniques of group separation, purification and CZE, a rapid and efficient method for the determination of naturally occurring diasteriomeric saponins is now available.     

Separation and determination of enkephalin-related peptides using capillary electrophoresis

CZE with UV-absorption detection has been used for the separation and determination of enkephalin-related peptides. The experimental conditions, such as pH and concentration of running buffer, applied voltage, injection method, and time, were investigated in detail. Excellent separation efficiency could be obtained for ten enkephalin-related peptides with a 50 microm (ID) x 58 cm capillary using sodium dihydrogen phosphate as the running buffer (pH 3.11) when 20 kV of applied voltage was used. The concentration detection limits were found to be in the range of 0.31-1.94 microg/mL (defined as S/N = 3). The proposed method has been applied to analyze the spiked cerebrospinal fluid (CSF) sample, and the results showed that CZE is a powerful technique for separation and detection of the above biological peptides.     

Determination of tobacco-specific N-nitrosamines in rabbit serum by capillary zone electrophoresis and capillary electrophoresis-electrospray ionization-mass spectrometry with solid-phase extraction

In this paper, we propose a new strategy for separation and determination of tobacco-specific N-nitrosamines (TSNAs), a group of strong carcinogens found only in tobacco products, by using CZE and CE-MS associated with SPE. Six TSNAs: N'-nitrosonornicotine, N'-nitrosoanatabine, N'-nitrosoanabasine, 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanone, 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanol, and 4-(methylnitrosamino)-4-(3-pyridyl)-1-butanol were simultaneously separated by either of two CZE methods, one of which worked with ammonium formate buffer (pH 2.5) and another with citrate buffer (pH 2.4), as well as a CE-MS method. The CZE conditions including pH and concentration of running buffer, capillary length, applied voltage, and capillary temperature were systematically optimized. For CE-MS method, an optimized sheath liquid consisted of methanol-water was used at a flow rate of 10 muL/min. With SPE procedure, our proposed CE-MS method was successfully applied to determine TSNAs after 15 min metabolism in rabbits. A comparison study between CZE and CE-MS methods for quantitative purposes was carried out, showing that both methods provided similar separation efficiency, selectivity, repeatability, linearity, and recovery. However, CE-MS method was better suited for the analysis of TSNAs in complicated biological samples for its sensitivity and extra information on molecular structure. Having good accordance with our previous work by using LC-MS, the new CE-MS method is expected to be an alternative to the LC-MS method and applied to study the metabolism of TSNAs.     

Enantioseparation in capillary electrophoresis using 2-O-(2-hydroxybutyl)-beta-CD as a chiral selector

The resolving ability of 2-O-(2-hydroxybutyl)-beta-CD (HB-beta-CD) with different degrees of substitution (DS = 2.9 and 4.0) as a chiral selector in CZE is reported in this work. Fourteen chiral drugs belonging to different classes of compounds of pharmaceutical interest such as beta-agonists, antifungal agents, ageneric agents, etc., were resolved. The effects of the DS of HB-beta-CD on separations were also investigated. The chiral resolution (R(s)) was strongly influenced by the concentrations of the CD derivative, the BGE, and the pH of the BGE. Under the conditions of 50 mmol/L Tris-phosphate buffer at pH 2.5 containing 5 mmol/L HB-beta-CD, all 14 analytes were separated. The very low concentration necessary to obtain separation was particularly impressive. The DS had a significant effect on the resolution of the chiral drugs and the ionic strength of the separation media; hence, the use of a well-characterized CD derivative is crucial.     

Differences in absorbance levels as found in capillary zone electrophoresis under stacking conditions

During some capillary zone electrophoresis (CZE) experiments, the baseline UV absorbance signal at 200 nm “jumped” from one stable level prior to the water plug (marking the flow of neutrals) to another stable level after the water plug. The phenomenon was further examined with distilled water as the sample and with different buffers, applied potentials, and salt concentrations in the buffer. It seems that there is an “isotachophoretic effect” on top of the CZE separations when running under stacking conditions. The effect results in a higher pH value of the buffer after the water plug compared to the pH prior to the plug. The nature of the buffer, the salt concentration in the buffer, and the applied potential all affect this phenomenon.     

Development of a CZE method for the determination of mizolastine and its impurities in pharmaceutical preparations using response surface methodology

A fast and selective CZE method for the determination of mizolastine and related impurities is described. Response surface methodology was applied to study the influence of phosphate/triethanolamine (TEA) buffer concentration, heptakis(2,3,6-tri-O-methyl)-beta-CD (TMbetaCD) concentration, voltage and temperature. The optimum conditions were: 105 mM phosphate/TEA buffer (pH 3.0) containing 10 mM TMbetaCD, temperature 19 degrees C and voltage 30 kV. Validation of the method was performed in drug substance and drug product. Robustness was evaluated using a Plackett-Burman design, including pH among the considered factors. Applying the optimal conditions, the nine peaks were baseline separated in about 10 min. The method was applied to the quality control of mizolastine in controlled-release tablets.     

Separation of human fibrinopeptides by capillary zone electrophoresis

We describe a method for the simultaneous determination of the five fibrinopeptide forms derived from the thrombin-promoted activation of human fibrinogen by capillary zone electrophoresis (CZE). The fibrinopeptide mixture was first desalted by a solid-phase extraction (SPE) step. The analysis was performed in reversed polarity in a highly cross-linked polyethylene glycol (PEG)-coated capillary with UV-light absorption detection at 200 nm. Several parameters including buffer concentration and pH, presence of an organic modifier, temperature, and applied voltage, have been tested. The best separations were obtained within 20 min, utilizing a 20 mM sodium phosphate buffer without organic modifier, in the narrow 6.1-6.2 pH range, at 25 degrees C, with an applied voltage of 20 kV. Quantitative analysis is made possible by the use of sheep fibrinopeptide A as an internal standard to correct for both extraction and injection errors.     

Simultaneous Determination of Atenolol and Chlorthalidone in Pharmaceutical Preparations by Capillary-Zone Electrophoresis

Abstract

A capillary zone electrophoresis (CZE) method for the simultaneous determination of the β-blocker drugs atenolol and chlorthalidone in pharmaceutical formulations has been developed. The CZE separation was performed under the following conditions: capillary temperature, 25°C; applied voltage, 25 kV; 20 mM H₃PO₄–NaOH running buffer (pH 9.0); and detection wavelength, 198 nm. Phenobarbital was used as internal standard. The method was validated and showed not only good precision and accuracy but also good robustness. The method has been successfully applied to the simultaneous determination of both atenolol and chlorthalidone in pharmaceutical tablets.     

Determination of berberine and strychnine in medicinal plants and herbal preparations by pressurized liquid extraction with capillary zone electrophoresis.

A simple and rapid method for the determination of berberine and strychnine in medicinal plants and herbal preparations for regulatory purposes using a home-made pressurized liquid extraction (PLE) system with capillary zone electrophoresis (CZE) using ultraviolet detection at 254 nm was developed. The effects of pH, concentration of buffer, and organic modifiers in the electrophoretic separation were investigated. The buffer used for CZE contained 50 mM ammonium acetate, pH 3.1. The effect of temperature on the extraction efficiency of strychnine in medicinal plants by PLE was demonstrated. Comparable or higher extraction efficiency was achieved with PLE for strychnine in medicinal plants and berberine in herbal preparations compared to soxhlet extraction. The effect of matrix interference in medicinal plants and herbal preparations containing a number of medicinal plants samples using CZE was investigated by standard additional experiments. The reproducibility of the method using PLE with CZE was found to vary between 2.4 and 10.7% (n = 5/6) for different types of samples on different days.     

Simultaneous determination of substrate and product in the process of preparation of valienamine by capillary zone electrophoresis

A simple and rapid CZE method was established for the simultaneous determination of valienamine, acarbose and validamycin A, using a 20‐kV CZE with the detection wavelength of 193 nm and 50 mM phosphoric acid–20 mM Tris (pH 5.3) as a running buffer. The calibration curves of valienamine, acarbose, and validamycin A showed a good linear relationship at a concentration range of 5–1000 μg/mL. The detection limits of valienamine, acarbose, and validamycin A were 0.3, 0.6, and 0.6 μg/mL, respectively, and the average recoveries of each of the above were 99.9, 99.5, and 100.3%. The method has been successfully applied for simultaneous determination of substrate and product in the process of preparation of valienamine.     

Determination of cytokinins in coconut (Cocos nucifera L.) water using capillary zone electrophoresis-tandem mass spectrometry

The applicability of CZE in combination with MS and MS/MS methods for the simultaneous separation and determination of 12 cytokinins was investigated for the first time. Cytokinins were first completely separated by CZE within less than 20 min using a volatile buffer and then detected directly by MS or MS/MS. Satisfactory separation of the 12 cytokinin standards was achieved using a 25 mM ammonium formate/formic acid buffer (pH 3.4) and 3% ACN v/v with a separation voltage of 25 kV. On the basis of the resolution of the neighboring peaks, the various parameters for CZE-MS optimization, such as buffer pH value, concentration of buffer and organic modifier, applied voltage and sheath liquid, were evaluated systematically. MS/MS with multiple reaction monitoring detection was carried out to obtain sufficient selectivity and sensitivity. The combination of on-line sample stacking and CZE-MS/MS achieved a detection limit in the range of 0.05-0.18 microM for the 12 cytokinins at an S/N of 3. The optimized CZE-MS/MS method was simple, rapid, low cost, robust and highly selective. Furthermore, the developed method was successfully applied to screen for endogenous cytokinins in purified coconut water extract sample. Nine cytokinins were detected and quantified in coconut water after SPE.     

Combined use of ionic liquid and sulfobutylether‐β‐cyclodextrin as electrolyte additives for separation and determination of camptothecin alkaloids by CZE

This work reported that ionic liquid (IL) ([Bmim] [PF₆]) and sulfobutylether‐β‐CD (SBE‐β‐CD) were used as electrolyte additives for the separation and determination of camptothecin (CPT) alkaloids by CZE. Separation parameters such as the buffer type, pH, and concentration of the running buffer, the concentration of SBE‐β‐CD and IL, temperature, and separation voltage were all investigated in order to achieve the maximum possible resolution. The four analytes were baseline separated within 10 min in capillary at the separation voltage of 15 kV with a running buffer consisting of 20 mM borate buffer, 20 mM IL, and 100 mM SBE‐β‐CD at pH 9.0. Under such conditions, good linearity about two orders of magnitudes of peak areas was achieved for the investigated CPT alkaloids with the correlation coefficients ranging from 0.9946 to 0.9985. For all analytes, detection limits (S/N = 3) and quantitation limits (S/N = 10) range from 0.05 to 0.92 μg/mL and 0.17 to 3.06 μg/mL, respectively. The proposed method has not only been successfully applied to the separation and determination of CPT alkaloids but also showed that IL seemed to be a promising additive in CZE separation.     

Simultaneous determination of cimetidine, famotidine, nizatidine, and ranitidine in tablets by capillary zone electrophoresis.

A simple capillary zone electrophoresis (CZE) method is described for the simultaneous determination of cimetidine (CIM), famotidine (FAM), nizatidine (NIZ), and ranitidine (RAN). The analysis of these drugs was performed in a 100 mM phosphate buffer, pH 3.5. Several parameters were studied, including wavelength for detection, concentration and pH of phosphate buffer, and separation voltage. The quantitative ranges were 100-1,000 microM for each analyte. The intra- and interday relative standard deviations (n = 5) were all less than 4%. The detection limits were found to be about 10 microM for CIM, 20 microM for RAN, 20 microM for NIZ, and 10 microM for FAM (S/N = 3, injection 1 s) at 214 nm. All recoveries were greater than 92%. Applications of the method to the assay of these drugs in tablets proved to be feasible.     

Influence of pH on electrophoretic behavior of phenothiazines and determination of pKa values by capillary zone electrophoresis

The influence of buffer pH on the electrophoretic behavior of 13 structurally related phenothiazines and determination of pK(a) values by capillary zone electrophoresis (CZE) were investigated. The results indicate that phenothiazines with a piperazine substituent behave quite differently from those with substituents having an aliphatic side chain or a piperidine moiety over the pH range studied. To separate these phenothiazines, it is preferable to select buffer pH in the range of 2.5-3.5. The pK(a) values of phenothiazines with three different types of substituents attached at the 10-position of the phenothiazine ring were determined. The determination of pK(a) values of phenothiazines allows us to rationalize the influence of buffer pH on the migration behavior of these compounds in CZE.     

Simultaneous quantification of energetically important metabolites in various cell types by CZE

A new CZE method was developed for the determination of 12 purine and pyrimidine nucleotides, two adenine coenzymes and their reduced forms, and acetyl coenzyme A in various cell extracts. As the concentration levels of these metabolites in living cells are low; CZE was combined with field‐enhanced sample stacking. As a result, the separation conditions were optimised to achieve a suitable resolution at the relatively high sample volume provided by this on‐line pre‐concentration technique. The optimum BGE was 150 mM glycine buffer (pH 9.5). Samples were introduced hydrodynamically using a pressure of 35 mbar (3.5 kPa) for 25 s, and data were collected at a detection wavelength of 260 nm. An applied voltage of 30 kV (positive polarity) and capillary temperature of 25°C gave the best separation of these compounds. The optimised method was validated by determining the linearity, sensitivity and repeatability and it was successfully applied for the analysis of extracts from Paracoccus denitrificans bacteria and from stem cells.     

毛细管电泳法和高效液相色谱法拆分联萘二酚酸对映体

采用毛细管电泳法和高效液相色谱法直接拆分2,2′-二羟基-1,1′-联二萘-3,3′-二甲酸(HBNC)对映体.以四种不同的β-环糊精为手性添加剂,考察环糊精的种类与浓度、缓冲液pH值及浓度、分离电压、温度等因素对HBNC分离的影响.结果表明:采用10 mmol/L磺丁基醚-β-环糊精+20 mmol/L磷酸盐缓冲液(pH=7.0),20 kV分离电压,HBNC对映体在20 min内达到基线分离,分离度达到3.31.采用(S)-叔-亮氨酸基-(S)-1-(α-萘基)乙胺手性柱,正己烷-乙醇-三氟乙酸(97∶3∶0.2,V/V)流动相,HBNC对映体在40 min内也基本达到基线分离.     

Enantioselective separation of chiral vicinal diols in capillary electrophoresis using a mono‐6A‐aminoethylamino‐β‐cyclodextrin as a chiral selector

This paper describes an improved access to mono‐6^A‐aminoethylamino‐β‐CD (β‐CDen), a very efficient cationic chiral selector for CZE in the separation of eight chiral aromatic vicinal diols. The β‐CDen concentration has a strong influence on the efficiency of enantioseparation. The effects of the pH and concentration of the BGE, the capillary temperature, and the applied voltage on the resolution and separation selectivity have been studied. Excellent chiral resolution was achieved under the optimal conditions of β‐CDen 10 mM, pH 10, 200 mM borate buffer at 15 kV and 20°C within 20 min. Moreover, the developed method was successfully applied to the determination of the enantiomeric purity of the catalytic asymmetric dihydroxylation (AD) reaction products.     

Development of a capillary zone electrophoresis method for the separation of a furan combinatorial library

Nine component mixtures of a furan library were simultaneously separated by capillary zone electrophoresis (CZE) using a phosphate buffer as a background electrolyte at low pH. The effects of buffer concentration, buffer pH, type and concentration of organic solvents on the electrophoretic mobility, resolution, and analysis time were systematically investigated. Resolution and efficiency of furan library components were further improved using cyclodextrin (CD)-modified CZE. Under optimum conditions, eight of the nine furans were baseline-resolved in less than 10 min at 30 kV using 50 mM phosphate buffer, 10% v/v acetonitrile (ACN), pH 2.0, with 5 mM gamma-CD.     

Analysis of the aconitine alkaloids in traditional Chinese medicines by nonaqueous capillary electrophoresis using a new recording mode

The determination of three aconitine alkaloids (hypaconitine, aconitine, mesaconitine) in five traditional Chinese medicines including two Tibetan medicines, Chuanwu, Caowu, Fuzi, Aconitum Tanguticum Maxim and Aconitum Gymnandrum Maxim by non-aqueous capillary electrophoresis using a new recording mode is described. The dissociation constants of aconitine, mesaconitine and hypaconitine have also been determined by CZE and were 7.71, 6.60 and 6.25, respectively. The separation was achieved by optimizing the applied voltage, the pH and the concentration of the buffer. The electrophoretic medium was 20 mM borax-70% (v/v) methanol (pH 8.5) and an uncoated capillary (50 cm x 75 microm i.d.) was used. Detection was carried out with a UV monitor at 214 nm. The total time for separation and determination was under 13 min.