Optimization towards reduction of efficiency droop in blue GaN/InGaN based light emitting diodes

Light emitting diodes (LEDs) based on GaN/InGaN material suffer from efficiency droop at high current injection levels. We propose multiple quantum well (MQW) GaN/InGaN LEDs by optimizing the barrier thickness and high–low–high indium composition to reduce the efficiency droop. The simulation results reflect a significant improvement in the efficiency droop by using barrier width of 10 nm and high–low–high indium composition in MQW LED.     

硅衬底InGaN/GaN基蓝光发光二极管droop效应的研究

InGaN/GaN基阱垒结构LED当注入的电流密度较大时, LED的量子效率随注入电流密度增大而下降, 即droop效应.本文在Si (111)衬底上生长了 InGaN/GaN 基蓝光多量子阱结构的LED,通过将实验测量的光电性能曲线与利用ABC模型模拟的结果进行对比, 探讨了droop效应的成因.结果显示:温度下降会阻碍电流扩展和降低空穴浓度, 电子在阱中分布会越来越不平衡,阱中局部区域中因填充了势能越来越高的电子而溢出阱外, 从而使droop效应随着温度的降低在更小的电流密度下出现且更为严重, 不同温度下实验值与俄歇复合模型模拟的结果在高注入时趋势相反.这此结果表明,引起 droop效应的主因不是俄歇非辐射复合而是电子溢出,电子溢出的本质原因是载流子在阱中分布不均衡.     

Optical excitation study on the efficiency droop behaviors of InGaN/GaN multiple-quantum-well structures

Efficiency droop is generally observed in electroluminescence under high current injection. Optical characterization on efficiency droop in InGaN/GaN multiple-quantum-well structures has been conducted at 12 K. Clear droop behaviors were observed for the sample excited by above-bandgap excitation of GaN with pulse laser. The results show that dislocation is not the crucial factor to droop under high carrier density injection, and Auger recombination just slightly affects the efficiency. The radiative recombination may be mainly affected by a multi-carrier-related process (diffusion and drift with a factor of n ^3.5 and n ^5.5) at the interface between GaN barrier and InGaN well.     

InGaN/GaN多量子阱结构发光二极管发光机理转变的低频电流噪声表征

本文对InGaN/GaN多量子阱结构发光二极管开启后的电流噪声进行了测试, 结合低频电流噪声的特点和载流子之间的复合机理, 研究了低频电流噪声功率谱密度与发光二极管发光转变机理之间的关系. 结论表明, 当电流从0.1 mA到10 mA逐渐增大的过程中, InGaN/GaN发光二极管的电流噪声行为从产生-复合噪声逐渐接近于低频1/f噪声, 载流子的复合机理从非辐射复合过渡为电子与空穴之间载流子数的辐射复合, 并具有标准1/f噪声的趋势, 此时多量子阱中的电子和空穴之间的复合趋向于稳定. 本文的结论提供了一种表征InGaN/GaN多量子阱发光二极管发光机理转变的有效方法, 为进一步研究发光二极管中载流子的复合机理、优化和设计发光二极管、提高其发光量子效率提供理论依据.     

Enhancement of light-emission efficiency of ultraviolet InGaN/GaN multiple quantum well light emitting diode with InGaN underlying layer

Two ultraviolet InGaN/GaN light emitting diodes (LEDs) with and without InGaN underlying layer beneath the multiple quantum wells (MQWs) were grown by metal-organic vapor phase epitaxy. Based on the photoluminescence excitation measurements, it was found that the Stokes shift of the sample with a 10-nm-thick In_0.1Ga_0.9N underlying layer was about 64 meV, which was smaller than that of the reference sample without InGaN underlying layer, indicating a reduced quantum-confined Stark effect (QCSE) due to the decrease of the piezoelectric polarization field in the MQWs. In addition, by fitting the photon energy dependence of carrier lifetime values, the radiative recombination lifetime of the sample with and without InGaN underlying layer were obtained about 1.22 and 1.58 ns at 10?K, respectively. The shorter carrier lifetime also confirmed that the QCSE in the MQWs was weakened after inserting the InGaN underlying layer. In addition, although the depth of carrier localization in the sample with InGaN underlying layer became smaller, the nonradiative recombination centers (NRCs) inside it decreased, and thus suppressed the nonradiative recombination process significantly according to the electroluminescence measurement results. Compared to the reference sample, the efficiency droop behavior was delayed in the sample with InGaN underlying layer and the droop effect was also effectively alleviated. Therefore, the enhanced light-emission efficiency of ultraviolet InGaN/GaN MQW LEDs could be attributed to the decrease of QCSE and NRCs.     

Variation of efficiency droop with quantum well thickness in In GaN/GaN green light-emitting diode

In GaN/GaN multiple quantum well(MQW) green light-emitting diodes(LEDs) with varying In GaN quantum well layer thickness are fabricated and characterized. The investigation of luminescence efficiency versus injection current reveals that several physical mechanisms may jointly influence the efficiency droop, resulting in a non-monotonic variation of droop behavior with increasing quantum well(QW) thickness. When the QW is very thin, the increase of In GaN well layer thickness makes the efficiency droop more serious due to the enhancement of polarization effect. When the QW thickness increases further, however, the droop is alleviated significantly, which is mainly ascribed to the enhanced nonradiative recombination process and the weak delocalization effect.     

Modeling and simulation of efficiency droop in GaN-based blue light-emitting diodes incorporating the effect of reduced active volume of InGaN quantum wells

The efficiency droop of InGaN-based blue light-emitting diodes (LEDs) is analyzed using numerical simulations with a modified ABC carrier recombination model. The ABC model is modified to include the effect of reduced effective active volume of InGaN quantum wells (QWs) and incorporated into the numerical simulation program. It is found that the droop of internal quantum efficiency (IQE) can be well explained by the effect of reduced light-emitting active volume without assuming a large Auger recombination coefficient. A simulated IQE curve with the modified ABC model is found to fit quite well with a measured efficiency curve of an InGaN LED sample when the effective active volume takes only 2.5% of the physical volume of QWs. The proposed numerical simulation model incorporating the reduced effective active volume can be advantageous for use in the modeling and simulation of InGaN LEDs for higher efficiency.     

具有三角形InGaN/GaN多量子阱的高内量子效率的蓝光LED(英文)

对InGaN量子阱LED的内量子效率进行了优化研究。分别对发光光谱、量子阱中的载流子浓度、能带分布、静电场和内量子效应进行了理论分析。对具有不同量子阱数量的InGaN/GaN LED进行了理论数值比对研究。研究结果表明,对于传统结构的LED而言,2个量子阱的结构相对于5个和7个量子阱具有更好的光学性能。同时还研究了具有三角形量子阱结构的LED,研究结果显示,三角形多量子阱结构具有较高的电致发光强度、更高的内量子效率和更好的发光效率,所有的优点都归因于较高的电子-空穴波函数重叠率和低的Stark效应所产生的较高的载流子输入效率和复合发光效率。     

A wide-narrow well design for?understanding the?efficiency droop in?InGaN/GaN light-emitting diodes

The electroluminescence efficiency at room temperature and low temperature (15 K) in a wide-narrow-well InGaN/GaN light-emitting diode with a narrow last well (1.5 nm) and a narrow next-to-last barrier (5 nm) is investigated to study the efficiency droop phenomenon. A reduced droop in the wide wells and a reduced droop at low temperatures reveals that inferior hole transportation ability induced Auger recombination is the root for the droop at high excitation levels.     

Efficiency droop suppression in GaN-based light-emitting diodes by chirped multiple quantum well structure at high current injection

Gallium nitride(Ga N) based light-emitting diodes(LEDs) with chirped multiple quantum well(MQW) structures have been investigated experimentally and numerically in this paper. Compared to conventional LEDs with uniform quantum wells(QWs), LEDs with chirped MQW structures have better internal quantum efficiency(IQE) and carrier injection efficiency. The droop ratios of LEDs with chirped MQW structures show a remarkable improvement at 600 m A/mm2,reduced down from 28.6%(conventional uniform LEDs) to 23.7%(chirped MQWs-a) and 18.6%(chirped MQWs-b),respectively. Meanwhile, the peak IQE increases from 76.9%(uniform LEDs) to 83.7%(chirped MQWs-a) and 88.6%(chirped MQWs-b). The reservoir effect of chirped MQW structures is the significant reason as it could increase hole injection efficiency and radiative recombination. The leakage current and Auger recombination of chirped MQW structures can also be suppressed. Furthermore, the chirped MQWs-b structure with lower potential barriers can enhance the reservoir effect and obtain further improvement of the carrier injection efficiency and radiative recombination, as well as further suppressing efficiency droop.     

Electrical Characteristics of InGaN/AlGaN and InGaN/GaN MQW Near UV-LEDs

Electrical characteristics of In0.05 Ga0.95N/Al0.07Ga0.9aN and In0.05 Ga0.95N/GaN multiple quantum well （MQW） ultraviolet light-emltting diodes （UV-LEDs） at 400hm wavelength are measured. It is found that for InGaN/AlGaN MQW LEDs, both ideality factor and parallel resistance are similar to those of InGaN/GaN MQW LEDs, while series resistance is two times larger. It is suggested that the Al0.07Ga0.93N barrier layer did not change crystal quality and electrical characteristic of p-n junction either, but brought larger series resistance. As a result, InGaN/AlGaN MQW LEDs suffer more serious thermal dissipation problem although they show higher light output efficiency.     

Enhanced performance of GaN-based light-emitting diodes with InGaN/GaN superlattice barriers

GaN-based multiple quantum well light-emitting diodes （LEDs） with conventional and superlattice barriers have been investigated numerically. Simulation results demonstrate using InGaN/GaN superlattices as barriers can effectively enhance performances of the GaN-Based LEDs, mainly owing to the improvement of hole injection and transport among the MQW active region. Meanwhile, the improved electron capture decreases the electron leakage and alleviates the efficiency droop. The weak polarization field induced by the superlattice structure strengthens the intensity of the emission spectrum and leads to a blue-shift relative to the conventional one.     

Modeling and analysis of the effects of inhomogeneous carrier distributions in InGaN multiple quantum wells

It is well known that carrier distribution in InGaN multiple quantum wells (MQWs) can be significantly inhomogeneous. However, the conventional ABC recombination model assumes that carriers are uniformly distributed throughout the MQW. In this paper, a modified ABC model that considers the unequal carrier density in the QWs was developed. From the analysis of the developed ABC model, the effective recombination coefficients and modified internal quantum efficiency (IQE) were obtained for an arbitrary carrier distribution in MQWs. The efficiency droop was found to be aggravated as the carrier distribution was increasingly inhomogeneous. However, it was also found that the effect of inhomogeneous carrier distribution alone was not sufficient to explain the IQE droop with the theoretical Auger recombination coefficient based on indirect Auger processes. The developed ABC model is expected to provide insight into the influence of inhomogeneous carrier distributions in MQWs on the efficiency droop in GaN-based light-emitting diodes.     

Theoretical investigation of Auger recombination on internal quantum efficiency of blue light-emitting diodes

The Auger recombination is recently proposed as one of the possible origins for the deteriorated internal quantum efficiency of InGaN light-emitting diodes. The Auger recombination behavior is quite different under widely varied Auger coefficients. The effect of Auger coefficient on the efficiency and output power is investigated numerically. The simulation results indicate that the Auger recombination with large Auger coefficient greatly decreases the efficiency in the whole current range under study. It is found that the electron current leakage and nonuniform hole distribution are the possible mechanisms responsible for the efficiency droop at high injection current.     

具有超晶格应力调制结构的绿光InGaN/GaN多量子阱的发光特性

研究了具有InGaN/GaN超晶格(SL)插入结构的绿光InGaN/GaN多量子阱(MQW)的发光特性。结构测试表明,SL插入结构并没有引起MQW中平均In组份的增加,而是改变了In组份的分布,形成了高In组份的量子点和低In组份量子阱。其电致发光(EL)谱和光致发光(PL)谱均出现了双发光峰。我们认为这两个 峰分别来自于量子点和量子阱,且存在着载流子从阱向点转移的输运机制。最后变温PL积分强度的Arrhenius 拟合表明,SL插入结构并没有在MQW中引入新的缺陷,使其发光效率下降。     

The effect of junction temperature on the optoelectrical properties of InGaN/GaN multiple quantum well light-emitting diodes

Thermal effects on the optoelectrical characteristics of green InGaN/GaN multiple quantum well (MQW) light-emitting diodes (LEDs) have been investigated in detail for a broad temperature range, from 30 °C to 100 °C. The current-dependent electroluminescence (EL) spectra, current–voltage (I–V) curves and luminescence intensity–current (L–I) characteristics of green InGaN/GaN MQW LEDs have been measured to characterize the thermal-related effects on the optoelectrical properties of the InGaN/GaN MQW LEDs. The experimental results show that both the forward voltages decreased with a slope of ?3.7 mV/K and the emission peak wavelength increased with a slope of +0.02 nm/K with increasing temperature, indicating a change in the contact resistance between the metal and GaN layers and the existence of a band gap shrinkage effect. The junction temperature estimated from the forward voltage and the emission peak shift varied from 25.6 to 14.5 °C and from 22.4 to 35.6 °C, respectively. At the same time, the carrier temperature decreased from 371.2 to 348.1 °C as estimated from the slope of high-energy side of the emission spectra. With increasing injection current, there was found to be a strong current-dependent blueshift of ?0.15 nm/mA in the emission peak wavelength of the EL spectra. This could be attributed to not only the stronger band-filling effect but also the enhanced quantum confinement effect that resulted from the piezoelectric polarization and spontaneous polarization in InGaN/GaN heterostructures. We also demonstrate a helpful and easy way to measure and calculate the junction temperature of InGaN/GaN MQW LEDs.     

It's not easy being green: Strategies for all‐nitrides,all‐colour solid state lighting

The design strategy presently employed to obtain ‘white’ light from semiconductors combines the emission of an InGaN blue or UV light‐emitting diode (LED) with that of one or more yellow‐orange phosphors. While commercially successful, this approach achieves good colour rendering only by increasing the number and spectral range of the phosphors used; compared to the alternative of combining ‘true’ red, green and blue (RGB) sources, it is intrinsically inefficient. The two major roadblocks to the RGB approach are 1. the green gap in the internal quantum efficiency (IQE) of LEDs; 2. the diode droop in the efficiency of LEDs at higher current densities. The physical origin of these effects, in the case of III‐nitrides, is generally thought to be a combination of Quantum Confined Stark Effect (QCSE) and Auger Effect (AE). These effects respectively reduce the electron–hole wave‐ function overlap of In‐rich InGaN quantum wells (QW), and provide a non‐radiative shunt for electron–hole recombination, particularly at higher excitation densities. SORBET, a novel band gap engineering strategy based upon quantum well intermixing (QWIM), offers solutions to both of the roadblocks mentioned above. In this introduction to SORBET, its great potential is tested and confirmed by the results of simulations of green InGaN diodes performed using the TiberCAD device modelling suite, which calculates the macroscopic properties of real‐world optoelectronic and electronic devices in a multiscale formalism. An alternative approach to the realisation of RGB GaN‐based LEDs through doping of an active layer by rare earth (RE) ions will also be briefly described. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Simulation of InGaN/GaN light-emitting diodes with a non-local quantum well transport model

Blue InGaN/GaN multiple quantum well (MQW) light-emitting diodes (LEDs) are simulated by the APSYS software with a non-local quantum well transport model which is used to describe the phenomenon that carriers can fly over the quantum wells directly. The simulation results based on this model are in good agreement with the experiment and show its significant influence on the output power, carrier transport, peak wavelength and current crowding effect of the InGaN/GaN MQW LEDs, indicating that the non-local quantum well transport plays an important role in these devices.     

Electroreflectance spectroscopy of compressively strained InGaN/GaN multi-quantum well structures

The built-in piezoelectric field induced by compressive stress in InGaN/GaN multi-quantum well (MQW) light-emitting diodes (LEDs) was investigated using the electric field dependent electroreflectance (ER) spectroscopic method. InGaN/GaN MQW structures were prepared on sapphire substrates of different thicknesses. Thinning the sapphire substrate enables control of the compressive stress by changing the curvature of the wafer bowing. The wafer bowing-induced mechanical stress alters the piezoelectric field in the InGaN/GaN MQW. The flat band voltage, estimated by measuring the applied reverse bias voltage that induces a 180° phase shift in the ER spectra, was decreased from −11.21 V to −10.51 V by thinning the sapphire substrate thickness from 200 to 60 μm. To calculate the piezoelectric field (F_pz) from the compensation voltage, the depletion width was obtained from the capacitance–voltage measurement. The F_pz estimated from the energy shift in ER peak in a bias range from 0 to −12 V was changed by 110 kV/cm.     

Anomalous disorder-related phenomena in InGaN/GaN multiple quantum well heterosystems

The influences of InGaN/GaN multiple quantum well (MQW) heterostructures with InGaN/GaN and GaN barriers on carrier confinement were investigated. The degree of disordering over a broad range of temperatures from 20 to 300 K was considered. The optical and electrical properties were strongly influenced by structural and compositional disordering of the InGaN/GaN MQW heterostructures. To compare the degree of disordering we examined the temperature dependence of the luminescence spectra and electrical conductance contingent on the Berthelot-type mechanisms in the InGaN/GaN MQW heterostructures. We further considered carrier transport in the InGaN/GaN disordered systems, probability of carrier tunneling, and activation energy of the transport mechanism for devices with InGaN/GaN and GaN barriers. The optical properties of InGaN/GaN disordered heterosystems can be interpreted from the features of the absorption spectra. The anomalous temperature-dependent characteristics of the disordered InGaN/GaN MQW structures were attributable to the enhancement of the exciton confinement.