Determination of impurities in highly pure platinum by inductively coupled plasma-atomic emission spectrometry

In this work, a cyclone spray chamber system is used in conjunction with an inductively coupled plasma-atomic emission spectrometer instead of the conventional Scott-type chamber system to reduce the lower limit of detection achieved by the instrument, and an internal standard element (Y) is introduced to eliminate the effects caused by the drift in the plasma background level. An ICP-AES method for the determination of 13 impurity elements in a highly pure platinum sample has been developed. In this method, it is not necessary either to add a platinum matrix to the calibration standard or to separate and concentrate the elements to be determined in the samples. The effect of the platinum matrix on the elements to be analyzed is corrected for by a background equivalent concentration subtraction method. The determination ranges of the method are as follows: 0.00010-0.0050% for Mg, Mn, Cu, Ag, Fe and Zn; 0.00030-0.015% for Au, Ir, Ni and Pb; 0.00050-0.025% for Rh and Al; and 0.00080-0.040% for Pd. The method is simple, rapid and accurate, and can be applied to the analysis of 99.9–99.995% pure platinum.     

Evaluation of spray chambers for use in inductively coupled plasma-atomic emission spectrometry

A laboratory-built spray chamber featuring aerosol collection at the centre of the chamber by means of a funnel is described and compared with a commercially available, dual tube chamber. The influence of some chamber design parameters on the emission signal intensity and stability, the nebulizer efficiency and chamber clean-out time is studied.     

电感耦合等离子体原子发射光谱法测定铈矿中微量的砷、锑

采用过氧化钠熔融试样，用盐酸调节试液酸度，对电感耦合等离子体原子发射光谱（ICP－AES）法同时测定铈矿中微量砷和锑进行了研究，考察了铈基体及共存元素，试液酸度及介质等因素对砷和锑的光谱和非光谱影响。     

Evaluation of vapor generation for the determination of nickel by inductively coupled plasma-atomic emission spectrometry

Volatile species of Ni were generated by merging acidified aqueous samples and sodium tetrahydroborate(III) in a continuous flow system. The gaseous analyte was subsequently introduced via a stream of Ar carrier into the inlet tube of the plasma torch. Inductively coupled plasma atomic emission spectrometry (ICP-AES) was used for detection. The operating conditions (chemical and physical parameters) and the concentrations of different acids were evaluated for the efficient generation of Ni vapor. The detection limit (3 sigma(blank)) was 1.8 ng mL(-1). The precision (RSD) of the determination was 4.2% at a level of 500 ng mL(-1) and 7.3% for 20 ng mL(-1) (n=10). The efficiency of the generation process was estimated to be 51%. The possible interfering effect of transition metals (Cd, Co, Cu, Cr, Fe, Mn, Zn), hydride forming elements (As, Ge, Pb, Sb, Se, Sn, Te), and Hg on Ni signal was examined. This study has demonstrated that Ni vapor generation is markedly free of interferences.     

Miniature hydride generator system for inductively coupled plasma-atomic emission spectrometry

Conclusion The detachable miniature hydride generator presented in this work gives the analytical chemist easy access to the determination of ultratrace levels of tin and germanium using a 1.2 kW-ICP spectrometer commercially available. An improvement of the detection limits of approximately 100 times those for conventional pneumatic nebulizer-ICP-AES, has been reported in this work.     

Development and characterization of bottom-viewed inductively coupled plasma-atomic emission spectrometry

In bottom-viewed inductively coupled plasma-atomic emission spectrometry (BV-ICP-AES), emission from the central channel of the plasma is measured axially from the bottom of the plasma. A straight quartz tube was used as a hollow light pipe (HLP) to collect plasma emission in this study. The HLP also serves as an injector for aerosols transport and injection into the ICP. The optical characteristics of HLPs with the original reflective surface and roughened outer surface are reported. The roughened HLP is effective in rejecting light beams that are not in line with the HLP. The transmission efficiency of the HLP, however, is high (> 70%) for light beams from a source that has the same dimension as the entrance of the HLP and is flush with the HLP. The HLP is effective in rejecting background emission from the core of the plasma that encircles the plasma central channel and yet efficient in light collection from the central channel of the plasma.     

Simultaneous determination of traces of impurities in high-purity molybdenum and molybdenum trioxide by coprecipitation and inductively coupled plasma-atomic emission spectrometry

Summary Inductively coupled plasma-atomic emission spectrometry (ICP-AES) has been developed for a simultaneous determination of traces of non-hydride-forming elements in high-purity Mo and molybdenum trioxide. Coprecipitation of diverse elements with lanthanum hydroxide is used to separate them from the Mo matrix and for concentration. Effects of pH and amount of La on the recoveries of diverse elements are discussed. Ten elements (Co, Cr, Cu, Fe, Mn, Ni, Ti, V, Zn, and Zr) are quantitatively recovered and determined. Matrix-matched calibration solutions are used for the determination.     

电感耦合等离子体原子发射光谱法测定自来水中的8种元素

采用电感耦合等离子体原子发射光谱法(ICP-AES)测定了化学实验室自来水中铝、钾、锶、钡、锰、钴、钼、硒8种元素的含量;对仪器的工作条件进行了优化,确定了各元素的分析波长和检出限.结果表明,所述方法可以方便地用于测定化学实验室自来水样品中的8种元素,相对标准偏差为0.08%～6.90%.     

Erbium determination in preforms of optical fibres by inductively coupled plasma-atomic emission spectrometry

Erbium which is used in the composition of heavy metal fluoride optical fibres was determined in preforms of these materials by inductively coupled plasma-atomic emission spectroscopy (ICP-AES). The new analytical procedure developed comprises: solid sample dissolution, via an alkaline fusion with sodium carbonate, and acid leaching with dilute hydrochloric acid, and measurements of emission intensities of 337.276 nm. This method has a detection limit of 31 ng/ml and a reproducibility of 0.90% r.s.d.     

Qualities related to spectra acquisition in inductively coupled plasma-atomic emission spectrometry

As many elements emit line-rich spectra in ICP-AES, the role of the resolution of the dispersive system has been considered as crucial not only to minimize spectral interferences but also to improve signal-to-background ratios. Resolution is mainly based on the line width measured at half of the peak intensity. Because of the availability of modern gratings, the practical resolution is no longer limited by the diffraction patterns produced by the grating, but is mainly bandpass and optical aberration limited. High resolutions of 5 pm may be obtained in the UV, which has to be compared with the physical line widths in the range 1–6 pm. However, such a high resolution cannot be achieved in the visible region because it is no longer possible to use a high line number for conventional gratings and high diffraction orders for echelle gratings. Moreover, the resolution concept does not consider the line wings, which are of concern for background correction. It is then suggested a measurement of the line profile at 1% of the peak intensity and a comparison with that measured at 50%. Because of the current possibility to have acquisition of the entire, or at least large portions of the UV-visible spectra, wavelength reproducibility may become the most important parameter to facilitate data processing such as spectra addition and subtraction, filtering, deconvolution and line correlation.     

Preconcentration and determination of trace elements with 2-aminoacetylthiophenol functionalized Amberlite XAD-2 by inductively coupled plasma-atomic emission spectrometry

2-Aminoacetylthiophenol (AATP)-modified Amberlite XAD-2 has been synthesized by coupling it through NNNH group. The resulting chelating resin, characterized by elemental analysis, thermogravimetric analysis (TGA) and infrared (IR) spectra, was used to preconcentrate Cd, Hg, Ag, Ni, Co, Cu and Zn ions. Several parameters, such as distribution coefficient and sorption capacity of the chelating resin, pH and flow rates of uptake and striping, volume of sample and eluent, were evaluated. The effects of electrolytes and cations on the preconcentration were also investigated. The recoveries were >96%. The procedure was validated by standard addition and analysis of a standard reference sediment material (GBW 07309 China). The developed method was utilized for preconcentration and determination of Cd, Hg, Ag, Ni, Co, Cu and Zn in tap water, river water and sediment samples by inductively coupled plasma-atomic emission spectrometry (ICP-AES) with satisfactory results. The 3σ detection limits for Cd, Hg, Ag, Ni, Co, Cu and Zn were found to be 0.10, 0.23, 0.41, 0.13, 0.25, 0.39 and 0.58 μg l⁻¹, respectively. The relative standard deviation of the determination was <10%.     

An indirect method for the determination of chromium species in water samples by sequential inductively coupled plasma-atomic emission spectrometry

Determination of Cr(VI) and Cr(III) in water samples by inductively coupled argon plasma-atomic emission spectrometry (ICP-AES) was performed indirectly employing an on-line system. For this purpose a column with copper shavings was used to reduce Cr(VI) to Cr(III) in acidic media, generating Cu(II) ions in the flow path. This process permitted the evaluation of concentrations in the range of 1–50 mg/l. The protocol allowed a throughput of 100 samples per hour with 10% precision in the concentration     

Preconcentration of trace elements on a support impregnated with sodium diethyldithiocarbamate prior to their determination by inductively coupled plasma-atomic emission spectrometry

A procedure is developed for determination of As, Co, Se, Cr, Pb, Zn, Cu, Mn, Cd, Sb, and Sn in water by ICP-AES analysis of alcohol eluates after pre-concentration of the samples. The pre-concentration is performed on a sodium diethyldithiocarbamate supported soft polyurethane foam. The sorbed elements are subsequently eluted with 1-propanol and the alcohol eluates are analysed by ICP-AES. A eight-fold concentration is achieved. An increased sensitivity in the analysis of propanol-water (30:70, v/v) solution is established as compared with aqueous solutions. The strongest effect is observed for As, Se, Pb, Cr, Sn, and Cd-increasing is more than twice. For other elements the matrix influence is by a factor of 1.45 (Cu), 1.36 (Sb), 2.08 (Zn). The method is applied to the analysis of natural water samples.     

Evaluation of closed-vessel microwave digestion method for the determination of trace impurities in polymer-based photoresist by inductively coupled plasma mass spectrometry

A closed microwave digestion method followed by inductively coupled plasma spectrometric (ICP-MS) analysis was evaluated for the determination of trace impurities in photoresist. To optimize the digestion procedure, several digestion parameters such as acid, heating temperature and heating time were evaluated. Besides, the digestion efficiency of used photoresist material and the recovery of analyte elements obtained by the use of gravimetric method and ICP-MS measurement, individually, were also compared to clarify the completeness of digestion. According to our experiments, the gravimetric method was found to be not so relevant to the completeness of digestion, because the remaining sample matrix could cause suppression effect in the subsequent ICP-MS measurement. In view of minimizing blank value and working time, a simple single-step heating program was proposed to mineralize 0.25 ml of photoresist material with 5 ml of nitric acid at 180 °C for 10 min. Based on the comparative study of the analytical results obtained by instrumental neutron activation analysis (INAA) and proposed method, the reliability of proposed method for the determination of trace metallic impurities in photoresist material has been confirmed.     

On-line preconcentration and simultaneous determination of heavy metal ions by inductively coupled plasma-atomic emission spectrometry

A flow injection analysis system for on-line preconcentration and simultaneous determination of Bi³⁺, Cd²⁺, Co²⁺, Cu²⁺, Fe³⁺, Ni²⁺, Pb²⁺ and Zn²⁺ in aqueous samples by inductively coupled plasma (ICP)-atomic emission spectrometry with a charge coupled detector is described. The preconcentration of analytes is accomplished by retention of their chelates with sodium diethyldithiocarbamate in aqueous solution on a solid phase containing octadecyl silica in a minicolumn. Methanol, as eluent, is introduced into the conventional nebulizer of the ICP instrument. The effects of different parameters, including preconcentration flow rate (equal to sample flow rate (SR)), eluent flow rate (ER), weight of solid phase (W) and eluent loop volume (EV), were optimized by the super-modified simplex method. The optimum conditions were evaluated to be SR 7.2 ml min⁻¹, ER 3.5 ml min⁻¹, W of 100 mg and EV of 0.8 ml. An enrichment factor of 312.5 for each analyte was obtained. The detection limits of the proposed method for Bi³⁺, Cd²⁺, Co²⁺, Cu²⁺, Fe³⁺, Ni²⁺, Pb²⁺ and Zn²⁺ were evaluated as 1.3, 1.0, 0.8, 0.3, 14.7, 0.5, 5.5 and 0.1 ng l⁻¹, respectively. The effect of several metal ions on percent recovery was also studied. The method was applied to the recovery of these heavy metals from real matrices and to the simultaneous determination of these cations in different water samples.     

Determination of trace impurities in high-purity cadmium by high-resolution inductively coupled plasma mass spectrometry.

Trace impurities in high-purity cadmium were determined by high-resolution inductively coupled plasma mass spectrometry (HR-ICP-MS). To overcome some potentially problematic spectral interference, measurements were acquired in both medium and high-resolution modes. The matrix effects due to the presence of excess HCl and cadmium were evaluated. The optimum conditions for the determination were tested in this experiment and discussed. The detection limits ranged from 0.01 to 0.27 microg g-1, depending on the elements. The results for the determination of 22 trace elements in high-purity cadmium are presented.     

Prediction of spectral interference in inductively coupled plasma-atomic emission spectrometry by primary computer expert system

Spectra and spectral interferences in inductively coupled plasma-atomic emission spectrometry, ICP-AES, have been simulated and predicted by a primary expert system under contrasting conditions of local temperature equilibrium (LTE) and non-LTE. In this expert system a comprehensive computer model has been applied to provide expert knowledge on an non-LTE ICP discharge, analyte ionization and excitation, and spectral line shape. The system also includes several databases to supply the calculation with spectral and elemental parameters. Some typical examples are illustrated, with satisfactory outcomes. It is found that predictions under non-LTE conditions are much closer to the reality than those under LTE conditions.     

Inductively coupled plasma-atomic emission spectrometry method for determination of trace metals in alkaline-earth matrices after flotation separation

An inductively coupled plasma-atomic emission spectrometry (ICP-AES) method is developed for determination of Cd, Co, Cr, Cu, Ni, Tl and Zn in traces in calcite, CaCO₃, dolomite, CaMg(CO₃)₂, and gypsum, CaSO₄. Interferences of a Ca/Mg matrix on analyte intensities were investigated. The results reveal that Ca does not interfere with Cr, Ni and Zn, but tends to decrease the intensity of the other elements. Magnesium as a matrix element does not interfere on with Zn, but increases the intensities of Ni, Cr and Cu, and decreases the intensities of Cd, Co and Tl. To eliminate these matrix interferences on trace element intensities, a flotation separation method is proposed. Lead(II) hexamethylenedithiocarbamate, Pb(HMDTC)₂, is applied as a collector for flotation of trace elements from acidic solutions of mineral samples. The flotation of acidic aqueous solutions of calcite, dolomite and gypsum was performed at pH 6.0, using 10 mg l⁻¹ Pb and 0.3 mmol l⁻¹ HMDTC⁻ added to 1 l of solution tested. The method detection limits of analytes in different minerals range from 0.02 to 0.06 μg g⁻¹ for Cd, 0.04 to 0.10 μg g⁻¹ for Co, 0.03 to 0.13 μg g⁻¹ for Cr, 0.02 to 0.16 μg g⁻¹ for Cu, 0.09 to 0.30 μg g⁻¹ for Ni, 6.45 to 7.71 μg g⁻¹ for Tl and 0.18 to 0.20 μg g⁻¹ for Zn.     

Determination of trace impurities in tantalum powder and its compounds by inductively coupled plasma optical emission spectrometry using solvent extraction

A procedure was developed for the analysis of 18 trace impurity elements in capacitor-grade tantalum powder (Ta), potassium tantalum fluoride (K₂TaF₇), and tantalum pentoxide (Ta₂O₅) using inductively coupled plasma optical emission spectrometry (ICP-OES). The detection limits achieved were in the ppb levels. The samples were dissolved in hydrofluoric acid (HF) in a microwave digestion system and the Ta matrix was extracted using cyclo hexanone. The impurity traces remained almost completely in the aqueous phase. The text was submitted by the authors in English.