水热改性对NiMo/γ-Al2O3加氢脱氮催化剂结构及性能的影响

The influence of hydrothermal modification on the structure and hydrodenitrogenation (HDN) activity of NiMo/γ-Al₂O₃catalyst was studied in the range 140～180 ℃. The experimental results indicated that the hydrodenitrogenation reaction rate of pyridine was accelerated using the NiMo/γ-Al₂O₃catalyst synthesized via hydrothermal route due to the change of the structure, the increase of the amount of Mo and Ni and the rise of the specific surface area. The change of the structure of catalysts was enhanced at higher hydrothermal temperature, producing NiMo/γ-Al₂O₃catalyst with better HDN activity.     

微量吸附量热研究CuO/γ-Al2O3催化剂的表面酸碱性质

The γ-Al₂O₃ supported CuO samples were studied. XRD results showed that the loading and calcination temperature affected the surface structure. For example， CuO crystallite appeared at the CuO loading of 7% (about 0.82mmol/100m²) on the support. Both CuO crystallite and CuAl₂O₄ spinel were present when the CuO/γ-Al₂O₃ sample was calcined at the same temperature (400℃). Microcalorimetric adsorption of CO₂ and NH₃ revealed that the strength of both the acidity and basicity decreased with the increase of CuO loading for the CuO/γ-Al₂O₃ sample. The increase of calcination temperature further decreased the basicity while the acidity was not affected.     

溶剂化金属原子浸渍法制备Pd-Cu/γ-Al2O3低温CO氧化催化剂

Nano-particle Pd/γ-Al₂O₃ monometallic and Pd-Cu/γ-Al₂O₃ bimetallic catalysts were prepared by solvated metal atom impregnation (SMAI) method. The results of XRD measurement indicated that Pd- Cu alloy was formed in the bimetallic catalysts and the crystalline particle size of the alloy increased as Cu contents increased with av-erage diameters < 6.0nm for all the samples. XPS and Auger spectra showed that Pd was in zero- valent state, Cu existed mainly in zero- valent state and partially in monovalent state Cu⁺. The Pd/γ-Al₂O₃ and Pd-Cu/γ-Al₂O₃ catalysts exhibited higher activity for CO oxidation at low temperature. The activity of Pd-Cu/γ-Al₂O₃ bimetallic catalyst was higher than that of Pd/γ-Al₂O₃ monometallic catalyst. The Pd-Cu/γ-Al₂O₃ catalyst with Pd/Cu atomic ratio of 1∶1 showed the highest activity.     

溶剂热合成具有纳米孔结构的γ -Al2O3

Nanoporous gamma aluminum oxide (γ-Al₂O₃) was synthesized by solvothermal method in the presence of AlCl₃·6H₂O, urea and alcohol. The calcined sample was characterized by XRD, FTIR, TEM, and Nitrogen adsorption-desorption measurement. Results show that the obtained γ-Al₂O₃ is well-dispersed nanoparticles with particle size of 4～7 nm and the product has nano-pore structure with a narrow pore size distribution of 5～20 nm.     

新型阴极材料Ba0.5Sr0.5Co0.8Fe0.2O3-σ制备与性能研究

Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3-σ(BSCF), a new cathode material for solid oxide fuel cell (SOFC), was synthesized by polyacrylicacid (PAA) method. The lattice structures of samples calcined at different temperatures were characte-rized by XRD. Shrinkage, porosity and pore size of the porous BSCF as a function of sintering temperature were investigated. It was found that the cubic perovskite structure could be formed after calcination at 800 ℃ for 2 h, but not well crystallized as seen from some unknown phases, and the pure cubic perovskite structure was formed after calcination at 1 150 ℃ for 2 h. The particle size of BSCF was less than 1～2 μm. The shrinkage of the porous BSCF increased with sintering temperature, but the opposite was true for the porosity. After sintering at 1 100 ℃ for 4 h, the porous BSCF was still in an appropriate structure, with porosity of 29% and electrical conductivity above 400 S·cm^-1.     

纳米尖晶石LixMn2O4的制备与电化学性能表征

Nano-spinel Li_xMn₂O₄(0.6 ≤x≤ 1.0) was synthesized by two steps of coprecipitation and calcination. The influences of calcination temperature, time and Li/Mn ratio on the crystal structure and the particle size of Li_xMn₂O₄ were investigated. It was shown that the higher the calcination temperature, the more complete the crystal structure, and the larger the particle size. Moreover, the influence of calcination time on the crystal structure was insignificant when it was more than 3h at 700℃. With the increase of x in Li_xMn₂O₄ in the range of 0.6～1.0, the d111 and lattice parameter a increased first and then decreased. The electrochemical properties of nano-spinel LiMn₂O₄ using as cathode material of lithium-ion battery were studied. The low discharge capacity might be due to the irreversible capacity loss brought by the large surface area and lattice vacancies of the nano-spinel.     

Ceramic Filter Balls Loaded with α-Fe2O3 and Their Application to NH3-N Wastewater Treatment

Hydrolysis reaction of Fe(NO₃)₃ at a high temperature in the presence of urea as the homogeneous precipitant was studied. With the prepared ceramic filter balls loaded with α-Fe₂O₃ after high temperature calcination, the loading of α-Fe₂O₃ on the porous ceramic filter balls from Fe(NO₃)₃ solutions of different concentrations and mechanical stability of the loaded α-Fe₂O₃ were studied. The product was characterized using XRD and SEM. Adsorption experiments were conducted to evaluate the performance of the product in adsorbing NH₃-N. It turned out that the specific surface area of the ceramic filter balls loaded with α-Fe₂O₃ had increased to 36.5387 m²/g from original 4.6127 m²/g. When the concentration of Fe(NO₃)₃ was 0.40 mol/L, the loading of α-Fe₂O₃ on the ceramic filter balls accounted for 8.4% of the total mass of the adsorbent and α-Fe₂O₃ was adsorbed on the filter balls very well. The adsorption isotherm of NH₃-N on the ceramic filter ball adsorbent loaded with α-Fe₂O₃ was of Langmuir type. The saturated adsorption capacity was 3.33 mg/L, and the adsorption constant K was 0.1873. NH₃-N was adsorbed by α-Fe₂O₃ more easily, which was a kind of specific adsorption.     

类钙钛矿新铌酸盐Ba6LaTi3Nb3O21的合成、结构与介电特性

A New Niobate Ba₆LaTi₃Nb₃O₂₁ was synthesized by high temperature solid state reaction in the BaO-La₂O₃-TiO₂-Nb₂O₅ system. The chemical compositions, crystal structure, microstructure, density and melting point of the new compound were characterized by EPMA, XRD, DTA and so on. Ba₆LaTi₃Nb₃O₂₁ crystallizes the rhombohedral system with unit cell parameters a=0.57388(2) nm, c=4.928 3(3) nm, and space group R3m, Z=3. The structure may be described as six (Nb,Ti)O₆ octahedra corner-sharing along c-axis to form perovskite layer connected by Ba atoms. The Ba₆LaTi₃Nb₃O₂₁ ceramics exhibits high dielectric of 74.1, low dielectric loss of 4.7×10^-4 and small temperature coefficient of dielectric constant of -69 ppm·K^-1 at 1 MHz due to its close structure and relative high dielectric polarizabilities of Ba²⁺, La³⁺, Ti⁴⁺ and Nb⁴⁺. Ba₆LaTi₃Nb₃O₂₁ might be a suitable candidate of high ε_r microwave dielectric ceramics.     

钒催化剂选择性氧化乳酸乙酯制丙酮酸乙酯

The structure and surface acidity of vanadium oxide supported on α-Al₂O₃、TiO₂、SiO₂ have been studied by XRD、IR、TPR and adsorption microcalorimetry. The catalytic performance of the catalysts for selective oxidation of ethyl lactate to ethyl pyruvate was determined in a continuous flow fix-bed reactor. The results showed that the dispersion of vanadium oxide on the supports weakened the V=O bond and actived the terminal oxygen, which increased the reaction activity. On the otherhand, The surface acidity is harmful to the selectivity of ethyl pyruvate. V/α-Al₂O₃ exhibited a lower conversion since its dispersion is low. The low selectivity on V/SiO₂ is due to its fairly strong surface acidity. Addition of K⁺ weakened the surface acidty and enhanced selectivity of V/SiO₂. V/TiO₂ exhibited the best activity and selectivity among the catalysts studied because of its weak surface activity. The conversion of ethyl lactate and selectivity to ethyl pyruvate are 97% and 81%, respectively, over the V/TiO₂ catalyst at 473K.     

层状类钙钛矿结构新铌酸盐KSr2Nb3O10

A new niobate compound KSr₂Nb₃O₁₀ was synthesized for the first time. The chemical compositions, crystal structure, optical property, density and melting point of the new compound were characterized by EPMA, TEM, XRD, DTA and so on. KSr₂Nb₃O₁₀ crystallizes the orthorhombic system with unit cell parameters a=0.7816(1) nm, b=0.7764(2) nm, c=2.9995(2) nm, V=1.8114(4) nm³, and space group P2₁2₁2₁, Z=8. The structure may be described as treble perovskite sheets ［Sr₂Nb₃O₁₀］^- interleaved with K⁺. Further, it was found that KSr₂Nb₃O₁₀ has intercalation phenomenon. Na⁺, Li⁺, H⁺, NH⁺₄ could exchange the interlayer cations K⁺ of KSr₂Nb₃O₁₀, and n-hexylamine also could intercalate into the place between the layers of ［Sr₂Nb₃O₁₀］^-.     

共沉淀法合成Cr3+∶Al2O3纳米粉体及其发光性能研究

NH₄MO(OH)HCO₃(M=Al³⁺， Cr³⁺) precursors were synthesized by a co-precipition method with the solutions of mixed nitrates as starting materials and ammonium bicarbonate as precipitator. The precursors and powders sintered at various temperatures were characterized by thermogravimetry/differential thermal analysis(TG/DTA)， infrared spectroscopy(IR)， X-ray diffractormetry(XRD)， transmittion electron microscopy(TEM). The luminescent spectra of Cr³⁺∶Al₂O₃ nano-powder was measured. The XRD results show that the pure-α-Al₂O₃ phase can be obtained at 1 200 ℃. TEM analysis indicates that the nano-powders about 20～30 nm are well-dispersed and less-aggregated. Spectral analysis demonstrates that the sample has good photoluminescence.     

Si5P6O25∶Tb3+的结构与荧光性质

Tb³⁺ ions were incorporated in P-Si matrix material through a sol-gel process. Luminescence properties of Tb³⁺ as a function of dopant， firing temperature， composition and structure of matrices were investigated. The gels synthesized by the reaction of P₂O₅ or H₃PO₄ with tetraethoxy silane and TbCl₃ as dopant were fired in air from the temperature 25～1000℃ to form P-Si crystalline phase. The crystal structure was determined by powder X-ray diffraction. Si₅O(PO₄)₆ were the only crystalline phase and belong to hexagonal crystal system. The emission of ⁵D₄-⁷F₅(～545nm) transition of Tb³⁺ in the P-Si system is composed of two peaks. The amount of doping Tb³⁺ varied from 0.664% to 1.644%， and no obvious concentration quenching was observed in this doping concentra-tion range. The intensity of Tb³⁺ emission increased with firing temperature increasing and becomes stable at 800～1000℃.     

分叉碳纳米管的催化生长

Branching carbon nanotubes were synthesized by pyrolysis of acetylene at 700℃ over oxygen-free copper and γ-Al₂O₃-supported Cu unitary or Cu/Fe binary catalysts. The morphologies of the as-grown products were charac-terized by transmission electron microscopy. The results indicated that the branching structures were closely related to the Cu component of the catalysts. We proposed that the special electronic structure (3d¹⁰4s¹) of Cu play the crucial role in the formation of the heptagon defects related to the branching structures.     

微等离子体氧化Al2O3陶瓷膜的组织结构与形成过程

The alumina ceramic coatings were prepared on aluminum alloy using micro-plasma oxidation. The structure and morphologies of ceramic coatings were studied by X-ray diffraction (XRD) and scanning electron microscope (SEM), and then its formation process was investigated. The results of XRD reveal that with increasing oxidation time the content of γ-Al₂O₃in the ceramic coatings decreases, and in which the content of α-Al₂O₃increases. The results of SEM show that many crater-mouth like traces formed by the plasma discharge are observed on the coatings surface, it indicates when the plasma is discharging, a plasma thermal chemical reaction occurs between the aluminum from the substrate and the oxygen and other ions from the electrolyte. The reaction products then are propelled away from the inner-wall of the discharging channels. Finally, these products agglomerate in the inner-wall of the discharging channels and on the surface near the discharging channels to produce the ceramic coatings. The change of ceramic coatings thickness with increasing oxidation time divides into two stages, and the final thickness is formed in first stage. With increasing current density the final thickness of ceramic coatings increases.     

La2O2S∶Mn2+荧光粉的微波合成及其荧光特性

Using La₂(SO₄)3 and the active carbon powder as reactants, La₂O₂S∶Mn²⁺ red phosphor was synthesized by microwave radiation method. The phosphor was characterized by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), laser-diffraction size analyzer and fluorospectrophotometer. The XRD analysis showed that the phosphor was pure phase La₂O₂S. The phosphor of La₂O₂S∶Mn²⁺ showed hexagonal crystal structure with diverse shapes, such as spherical and rod, with average particle size of 10.22 μm. The emission and excitation spectra of the phosphor were determined by fluorospectrophotometer and the results showed that the excitation spectrum of the phosphor under 600 nm emission wavelength was excitation bands between 250 nm and 350 nm with a peak value of 303 nm. Then ,when exicited under UV 303 nm, the phosphor showed broad band emission of 550~700 nm with a peak at 607 nm. In addition, the optimal effects were obtained for the phosphor preparation when the concentration of the activator Mn²⁺ was x_Mn=0.01, the ratio of C and O (n_C / n_O) in the reactants was 0.6∶1, and the time of reaction was about 1 h. La₂O₂S∶Mn²⁺ has strong absorption of UV spectrum and can emit bright red light.     

Eu3+掺杂SiO2-B2O3-NaF玻璃的制备及发光性质

The Eu-doped SiO₂-B₂O₃-NaF glass was prepared by sol-gel process, using tetraethoxy Silicane, boric acid and sodium fluoride as starting materials, 0.10 mol·L^-1 EuCl₃ solution as the dopant. The luminescent properties of Eu³⁺ doped SiO₂-B₂O₃-NaF phosphors were investigated. The phosphors showed prominent luminescence in pink, the strong emission of Eu³⁺ comes from electronic transition of ⁵D₀- ⁷F₁（591 nm）and ⁵D₀- ⁷F₂（615 nm）,which derived from two transition modes of magnetic-dipole and electric-dipole .The peak intensity of 591nm in SiO₂-B₂O₃-NaF matrix is much stronger than it in the other matrixes, it means that SiO₂-B₂O₃-NaF has sensitization on the transition of ⁵D₀- ⁷F₁ (Eu³⁺). If there are broad bonds in the range of 275～380 nm in the excitation spectrum of Eu³⁺ -doped SiO₂-B₂O₃-NaF glass, the emission peak intensity should be intensified. It is because the electron migration CT band of O^2--Eu³⁺. For all Eu³⁺ concentrations used, the investigation found that when the mass of fraction got to 29.19×10^-3, the luminescence intensity reached the summit. And there is a phenomenon of concentration quenching. Investigation with the same concentration of Eu³⁺ at different annealed temperature, we found that the sample annealed at 400 ℃, the luminescence intensity achieved its maximum value, and Eu³⁺ in this matrix had a phenomenon of temperature quenching. The structural characterization of these luminescent materials was carried by used XRD and TEM. The result showed that the phosphor was in amorphous phase.     

SrTi0.9M0.1O3-δ钙钛矿型氧化物催化剂甲烷氧化偶联反应性能的研究

The structure and catalytic properties of SrTi_0.9M_0.1O_3-δ (M=Mg，Al， Zr) perovskite-type catalysts for ox-idative coupling of methane (OCM) have been studied by using X-ray diffraction (XRD)，X-ray photoelectron spectroscopy (XPS) and temperature-programmed desorption of oxygen(O₂-TPD) methods. It has been shown that doping the cations of lower valence (e.g. Mg²⁺， Al³⁺) to the B site of SrTi_0.9M_0.1O_3-δ perovskite-type catalysts results in the higher content of adsorbed oxygen species on the surface of catalysts and thus higher C₂-selectivity for OCM reaction. It is suggested that the oxygen vacancies of SrTi_0.9M_0.1O_3-δ (M=Mg， Al， Zr) perovskite-type catalysts are the sites responsible for oxygen activation， and the adsorbed oxygen species on the surface of SrTi_0.9M_0.1O_3-δ catalysts are the main active species for OCM reaction.     

溶胶凝胶法制备Nd2O3改性钛酸钡陶瓷的研究

The technological condition for the preparation of BaTiO₃ ceramics doped with Nd₂O₃ by Sol-Gel was deter-mined through orthogonal experiment. When n_Ba(Ac)2∶n_Ti(OC4H9)4∶n_Nd2O3∶n_{CH3(CH2)2CH2OH}∶n_H2O=1.00∶1.00∶0.003∶7.30∶37.04, pH=3.5,T=25℃,the light-yellow-transparent-stable solution and thorough transparent gel was generat-ed, the transforming time of solution to gel was 25h. The crystal structure and particle size of BaTiO₃ ceramics doped with Nd₂O₃ were studied by SEM and X-ray respectively, the type of the crystal was tetragonal, the particle size was about 24.7nm. The dielectric constant (ε) and dielectric loss (tanδ) of BaTiO₃ ceramics doped with Nd₂O₃ were determined between 10⁴～10⁶Hz, and the results showed that the dielectric constant was increased obviously, the dielectric loss was decreased clear and the resistivity (ρ_V) was also decreased noticeably.     

二聚体配合物[(n-Bu)2Sn(C10H8N2O3)(C2H5OH)]2的合成和晶体结构

The novel seven-coordinate complex [(n-Bu)₂Sn(C₁₀H₈N₂O₃)(C₂H₅OH)]₂ (C₁₀H₈N₂O₃^2- is the dinegative ion of 2-oxo-propionic acid benzoyl hydrazone) was synthesized by the reaction of (n-Bu)₂SnO with 2-oxo-propionic acid benzoyl hydrazone in 1∶1 molar ratio in benzene-ethanol (V/V, 3/1), and its structure was characterized by X-ray single crystal diffraction. The crystal belongs to a tetragonal system with space group I4₁/a, a=2.4890(2)nm, b=2.4890(2)nm, c=1.5170(3)nm, V=9.398(2)nm³, Z=8, F(000)=3968, D_c=1.366g·cm^-3, and the structure was refined to final R₁=0.0530, wR₂=0.0971. The structure of the title complex is described as a dimer through weak interactions of Sn…O bonding and hydrogen bond. The tin atoms rendered sev-en-coordination in a distorted pentagonal bipyramid geometry structure, four oxygen atoms [O1, O2, O2^#1 and O4] and one nitrogen atom N2 formed the equatorial plane and C11-Sn1-C15 is the axis. CCDC: 212696.