Plasma electrolytic oxidation coating on AZ91 magnesium alloy modified by neodymium and its corrosion resistance

Ceramic coatings on the surfaces of Mg-9Al-1Zn (AZ91) magnesium alloy and Mg-9Al-1Zn-1Nd magnesium alloy (AZ91 magnesium alloy modified by neodymium, named as AZ91Nd in this paper) are synthesized in aluminate electrolyte by plasma electrolytic oxidation (PEO) process, respectively. X-ray diffraction and X-ray photoelectron spectroscopy analyses show the PEO coating on the Mg-9Al-1Zn-1Nd alloy comprises not only MgO and Al₂O₃, which are found in the coating on the AZ91 alloy, but also a trace amount of Nd₂O₃. Microstructure observations indicate the addition of Nd can decrease the sizes of β phases and form Al₂Nd intermetallics in the AZ91 alloy. The fine β phases can effectively restrain the formation of unclosed-holes and greatly decrease the sizes of pores in the coating during the PEO process. In addition, the Al₂Nd intermetallics can be completely covered due to the lateral growth of the PEO coatings formed on the α and β phases. As a result, the coating on the AZ91Nd alloy possesses a dense microstructure compared with that on the AZ91 alloy. The following corrosion tests indicate the corrosion resistance of the PEO coating on the AZ91Nd alloy is evidently higher than that of the PEO coating on the AZ91 alloy.     

Effects of duty ratio at low frequency on growth mechanism of micro-plasma oxidation ceramic coatings on Ti alloy

The aim of this work is to study the effects of duty ratio on the growth mechanism of the ceramic coatings on Ti-6Al-4V alloy prepared by pulsed single-polar MPO at 50 Hz in NaAlO₂ solution. The phase composition of the coatings was studied by X-ray diffraction, and the morphology and the element distribution in the coating were examined through scanning electron microscopy and energy dispersive spectroscopy. The thickness of the coatings was measured by eddy current coating thickness gauge. The corrosion resistance of the coated samples was examined by linear sweep voltammetry technique in 3.5% NaCl solution. The changes of the duty ratio (D) of the anode process led to the changes of the mode of the spark discharge during the pulsed single-polar MPO process, which further influenced the structure and the morphology of the ceramic coatings. The coatings prepared at D = 10% were composed of a large amount of Al₂TiO₅ and a little γ-Al₂O₃ while the coatings prepared at D = 45% were mainly composed of α-Al₂O₃ and γ-Al₂O₃. The coating thickness and the roughness were both increased with the increasing D due to the formation of Al₂O₃. The formation of Al₂TiO₅ resulted from the spark discharge due to the breakdown of the oxide film, while the formation of Al₂O₃ resulted from the spark discharge due to the breakdown of the vapor envelope. The ceramic coatings improved the corrosion resistance of Ti-6Al-4V alloy. And the surface morphology and the coating thickness determined the corrosion resistance of the coated samples prepared at D = 45% was better than that of the coated samples prepared at D = 10%.     

Improvement of surface porosity and properties of alumina films by incorporation of Fe micrograins in micro-arc oxidation

Micro-arc oxidation (MAO) is an effective approach to improve the properties of aluminum and its alloy by forming ceramic films on the surface. However, the oxide layers often have a porous surface structure, which exhibits relatively high friction coefficients. In this work, in order to enhance the surface and mechanical properties of the films produced by micro-arc oxidation, Al₂O₃ coatings embedded with Fe micrograins of different thicknesses were produced on aluminum alloys by adding Fe micrograins into the electrolyte during MAO. Compared to the Al₂O₃ coatings without Fe micrograins, the MAO Al₂O₃ coatings with Fe micrograins are much denser and harder, and the wear resistance is also improved significantly. The enhancement can be attributed to the enhancement of the surface structure and morphology of the MAO Al₂O₃ coatings with embedded Fe micrograins.     

Growth characteristics of micro-plasma oxidation ceramic coatings on Ti alloy by inductively coupled plasma-atomic emission spectrometer technique

The aim of this work was to study the growth characteristics of micro-plasma oxidation ceramic coatings on Ti-6Al-4V alloy. Compound ceramic coatings were prepared on Ti-6Al-4V alloy by pulsed micro-plasma oxidation (MPO) in NaAlO₂ solution. The phase composition and surface morphology of the coating were investigated by X-ray diffractometry and scanning electron microscopy. The solution of Ti from the substrate and the content of Al in the electrolyte were studied by inductively coupled plasma-atomic emission spectrometer (ICP-AES) technique. Ti from the substrate dissolved and came into the coating and the electrolyte during MPO process. The content of Ti in the electrolyte under the pulsed bi-polar mode was more than that of the pulsed single-polar mode. The phase composition and structure of the coating was attributable to the space steric hindrance of Al congregated on the electrode surface due to the effect of the electric field and the electrolyte characters. For the pulsed single-polar mode, the coating was mainly composed of a large amount of α-Al₂O₃ and a small amount of γ-Al₂O₃. And the coating was mainly structured by Al from the electrolyte. However, the coating was composed of a large amount of Al₂TiO₅ and a little α-Al₂O₃ and rutile TiO₂ for the pulsed bi-polar mode. And the coating was structured both by Ti from the substrate and Al from the electrolyte.     

Characterization of ceria-yttria stabilized zirconia plasma-sprayed coatings

Ceria-yttria stabilized zirconia (CYSZ) coatings were prepared by air plasma-sprayed on the nickel alloy. The as-sprayed CYSZ coatings and heat-treated CYSZ coatings were characterized by X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD). The XPS data indicated the coexistence of Ce³⁺, Ce⁴⁺, Y³⁺ and Zr⁴⁺ ions near the surface of the as-sprayed CYSZ coatings and the disappearance of Ce³⁺ ions in the CYSZ coatings after thermal treatment at 1000 °C for 15 h. From the XRD patterns, the solid solution of CeO₂-Y₂O₃-ZrO₂ formed in the CYSZ coatings because of the lack of any features from Y₂O₃ and ZrO₂ single phases. After thermal treatment, the main phases of all the samples were consistent with the characteristic peaks of cubic ZrO₂.     

Microstructure and properties of Ni-Co/nano-Al2O3 composite coatings by pulse reversal current electrodeposition

Ni-Co/nano-Al₂O₃ (Ni-Co/Al₂O₃) composite coatings were prepared under pulse reversal current (PRC) and direct current (dc) methods respectively. The microstructure of coatings was characterized by means of XRD, SEM and TEM. Both the Ni-Co alloy and composite coatings exhibit single phase of Ni matrix with face-centered cubic (fcc) crystal structure, and the crystal orientation of the Ni-Co/Al₂O₃ composite coating was transformed from crystal face (2 0 0) to (1 1 1) compared with alloy coatings. The hardness, anti-wear property and macro-residual stress were also investigated. The results showed that the microstructure and performance of the coatings were greatly affected by Al₂O₃ content and the electrodeposition methods. With the increasing of Al₂O₃ content, the hardness and wear resistance of the composite coatings enhanced. The PRC composite coatings exhibited compact surface, high hardness, better wear resistance and lower macro-residual stress compared with that of the dc composite coatings.     

Preparation and high-temperature properties of Au nano-particles doped α-Al2O3 composite coating on TiAl-based alloy

Au nano-particles doped α-Al₂O₃ composite coatings were successfully prepared on TiAl-based alloy by electrodeposition, using the Al₂O₃ sols with minor addition of HAuCl₄ solution. The even distribution of Au nano-particles (<2.0 wt.%) in the α-Al₂O₃ matrix has been observed. Isothermal oxidation tests of the samples coated with the as-prepared novel coatings at 900 °C in static air for 200 h shown that the oxygen inward diffusion can be effectively suppressed to a low level. The results of high-temperature cyclic oxidation test at 900 °C in air revealed that the oxidation and spallation resistance of TiAl-based alloy were improved significantly under thermal cycling. In the as-prepared coatings, cracks were shielded by means of crack bridging and the fracture resistance of the formed scales can be improved by toughening effects of the composite structure. Surface scratching tests after the cyclic oxidation exhibited that the adhesion of the formed composite scale on TiAl-based alloy was remarkably improved by the Au nano-particles doped α-Al₂O₃ composite coating.     

Structure and mechanical properties of ceramic coatings fabricated by plasma electrolytic oxidation on aluminized steel

Ceramic coatings were formed by plasma electrolytic oxidation (PEO) on aluminized steel. Characteristics of the average anodic voltages versus treatment time were observed during the PEO process. The micrographs, compositions and mechanical properties of ceramic coatings were investigated. The results show that the anodic voltage profile for processing of aluminized steel is similar to that for processing bulk Al alloy during early PEO stages and that the thickness of ceramic coating increases approximately linearly with the Al layer consumption. Once the Al layer is completely transformed, the FeAl intermetallic layer begins to participate in the PEO process. At this point, the anodic voltage of aluminized steel descends, and the thickness of ceramic coating grows more slowly. At the same time, some micro-cracks are observed at the Al₂O₃/FeAl interface. The final ceramic coating mainly consists of γ-Al₂O₃, mullite, and α-Al₂O₃ phases. PEO ceramic coatings have excellent elastic recovery and high load supporting performance. Nanohardness of ceramic coating reaches about 19.6 GPa.     

Nb-Al合金高温氧化机理

通过自编软件建立了铝氧化膜与基体铌界面的原子集团模型,用递归法计算了合金的原子埋置能、原子结合能等电子参数,从电子层面分析铌合金高温氧化机理.研究表明:铝通过晶界扩散偏聚在合金表面,并与氧结合生成致密的Al2O3氧化膜,阻挡氧向铌基体扩散.晶界和稀土元素能提高氧化膜与基体间的原子结合能,增加其界面的结合强度,加强氧化膜与基体铌间的黏附性.因此,通过在合金中添加稀土元素或细化合金晶粒均能提高铌合金的抗高温氧化性能.     

Interface characteristics and mechanical properties of short carbon fibers/Al composites with different coatings

Three kinds of coatings, Ni, Cu and Al₂O₃, were obtained on the surface of short carbon fibers (SCFs). The interface characteristics and mechanical properties of SCFs/Al composites with the various coatings were systematically studied in this paper. The results showed that, compared to non-coating, Ni or Cu coating improved the wettability of SCFs and Al melt. However, the harmful phases Al₃Ni or CuAl₂ generated in interface zone and Al matrix result in the lower mechanical properties. Al₂O₃ coating protected the SCFs and prevented the harmful reaction of Al and SCFs. The interface of Al/Al₂O₃/SCF without any other phase was clean and well bonded, and the Al₂O₃-coated SCFs/Al composite had the highest mechanical properties. The interfacial indentation and fracture mechanism of all the composites were analyzed in detail.     

Investigation of Glasses and Glaze Coats of Composition R2O–RO–Fe2O3(FeO)–Al2O3–B2O3–SiO2 by the EPR Method

The valence state and the coordination environment of the paramagnetic centers of iron ions in glasses and vitreous coats of composition R₂O–RO–Fe₂O₃(FeO)–Al₂O₃–B₂O₃–SiO₂ have been investigated by the EPR method. The tetrahedral and octahedral coordinations of Fe³⁺ ions have been revealed. The character of change in the EPR spectra of the materials studied in the vitreous and vitrocrystalline state has been determined. It is shown that the coordination number of iron ions is dependent on the crystallization processes.     

Interfacial reactions and oxidation behavior of Al2O3 and Al2O3/Al coatings on an orthorhombic Ti2AlNb alloy

The uniform and dense Al₂O₃ and Al₂O₃/Al coatings were deposited on an orthorhombic Ti₂AlNb alloy by filtered arc ion plating. The interfacial reactions of the Al₂O₃/Ti₂AlNb and Al₂O₃/Al/Ti₂AlNb specimens after vacuum annealing at 750 °C were studied. In the Al₂O₃/Ti₂AlNb specimens, the Al₂O₃ coating decomposed significantly due to reaction between the Al₂O₃ coating and the O-Ti₂AlNb substrate. In the Al₂O₃/Al/Ti₂AlNb specimens, a γ-TiAl layer and an Nb-rich zone came into being by interdiffusion between the Al layer and the O-Ti₂AlNb substrate. The γ-TiAl layer is chemically compatible with Al₂O₃, with no decomposition of Al₂O₃ being detected. No internal oxidation or oxygen and nitrogen dissolution zone was observed in the O-Ti₂AlNb alloy. The Al₂O₃/Al/Ti₂AlNb specimens exhibited excellent oxidation resistance at 750 °C.     

Evolution of MgAl<Subscript>2</Subscript>O<Subscript>4</Subscript> crystals in Al-Mg-SiO<Subscript>2</Subscript> composites

The present study analyzes the morphological transformations of reaction products i.e., MgO, MgAl₂O₄ occurring during the reaction between SiO₂ and Al-Mg alloy in Al-Mg-SiO₂ composite processed by the liquid metallurgy technique. Different phases of platelet and hexagonal morphologies are detected and their composition analysis by EDS has confirmed them as being transition phases existing between MgO, MgAl₂O₄ and Al₂O₃. This study has also revealed the gradual transformation of (i) MgO needles to octahedral MgAl₂O₄ through Mg-Al-Si-O and Mg-Al-O transition phases having platelet morphologies and (ii) MgAl₂O₄ to Al₂O₃ through hexagonal transition phases on holding of Al-5Mg-SiO₂ and Al-1Mg-SiO₂ composites respectively at 1023K. Fully developed α-Al₂O₃ crystals are not observed under the present experimental conditions, wherein the Mg content is well above the equilibrium Mg content required for the formation of stable Al₂O₃ (<0.05 wt. %). PACS 05.70.Np     

Atmospheric reactive plasma sprayed Fe-Al2O3-FeAl2O4 composite coating and its property evaluation

In the present study, Fe-Al₂O₃-FeAl₂O₄ composite coatings were successfully deposited by reactive plasma sprayed Al/Fe₂O₃ agglomerated powder. Phase composition and microstructure of the coatings were determined by XRD and SEM. The results indicated that the composite coatings were principally composed of three different phases, i.e. FeAl₂O₄ phase as main framework, dispersed ball-like Fe-rich phase, and small splats of Al₂O₃ phase, and it was thought that the in situ synthesized metal phase was helpful to toughen the coating matrix. According to the results of the indentation and frictional wear tests, the composite coating exhibited excellent toughness and anti-friction properties in comparison with conventional Al₂O₃ monophase coating, though its microhardness value was a little lower than that of Al₂O₃ coating. The formation mechanism and the toughening mechanism of the composite coating were clarified in detail.     

Laser surface remelting of plasma sprayed nanostructured Al2O3-13wt%TiO2 coatings on titanium alloy

Plasma sprayed nanostructured coatings were successfully fabricated on a titanium alloy (Ti-6Al-4V) substrate using the as-prepared nanostructured Al₂O₃-13wt%TiO₂ feedstock. A CO₂ laser was used to remelt the plasma sprayed coatings. The effects of laser remelting on the phase constituents, microstructure and properties of the ceramic coatings were investigated. The laser remelted coatings (LRmC) possessed a much denser and more homogenous structure and excellent metallurgical bonding to the substrate. The average porosity of the LRmC was reduced to 0.9%, compared with 6.2% of the as-sprayed coatings. The net-like structure in the as-prepared feedstock remained in the coatings before and after laser remelting. The metastable γ-Al₂O₃ phase in the as-sprayed coatings transformed to stable α-Al₂O₃ during laser remelting. The LRmC could remain nanostructure. The microhardness of the coatings was enhanced to 1000-1400 HV_0.3 after laser remelting, which was much higher than that of the plasma sprayed coatings and 2-3 times higher that of the substrate. Significant decreases in surface roughness were also found in the LRmC.     

Microstructure and properties of TiB2-containing coatings prepared by arc spraying

Low cost arc spraying and cored wires were used to deposit composite coatings consisting of TiB₂ and TiB₂/Al₂O₃ hard particles in a Ni(Cr) and stainless steel 304L matrix. Four coatings were prepared namely Ni(Cr)-TiB₂, Ni(Cr)-TiB₂/Al₂O₃, 304L-TiB₂ and 304L-TiB₂/Al₂O₃. The microstructural characteristics of powders and coatings were observed by scanning electron microscopy (SEM). Phase compositions of powders were analyzed by X-ray diffraction (XRD). Although all the analyzed coatings exhibited similar lamella structure, remarkable differences not only in the morphology of hard phase and matrix but also in the size and distribution of hard phases were observed from one coating to another. Tribological behavior of the coatings was analyzed in room temperature dry sliding wear tests (block-on-ring configuration), under 75 N at low velocity (0.5 m/s). The coatings showed far high wear resistance than low carbon steel substrate under same conditions examined. Wear loss of 304L-TiB₂ and Ni(Cr)-TiB₂ coatings were lower nearly 15 times than that of steel substrate. TiB₂ hard phases in coatings bonded well with metal matrix contributed to high wear resistance.     

Microstructure and mechanical properties of alumina coatings prepared by double glow plasma technique

Low-temperature growth (600 °C) of α-Al₂O₃ coatings on the stainless steel substrate by double glow plasma technique was achieved. The compositions and microstructures of the coatings prepared at different oxygen flow rates were characterized, respectively, by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) spectrometry. A phenomenological mechanism for the formation of the Al₂O₃ ceramic coatings during the oxidation process was proposed on the basis of the experimental results. It was obvious that the oxygen flow rates had a great effect on the surface structure of the prepared Al₂O₃ coatings. The dense and smooth Al₂O₃ coatings were prepared at the oxygen flow rate of 15 sccm. In addition, the correlations between the mechanical properties of Al₂O₃ coating and oxygen flow rates were also discussed. The coating prepared at 15 sccm oxygen flow rate exhibited the best mechanical properties with a maximum hardness of 31 GPa and elastic modulus of 321 GPa. The corresponding critical load of scratch adherence for this sample was 47 N.     

Effect of nano-Y2O3 on microstructure of laser cladding cobalt-based alloy coatings

Cobalt-based alloy coatings with and without nano-Y₂O₃ particles produced by a 5 kW CO₂ laser on Ni-based superalloy were introduced. Solidified microstructure, phase compositions and distribution of nano-particles were investigated by using optical microscope, SEM, TEM and XRD. The results showed that metastable phases, such as γ-Co and Cr₂₃C₆ existed in cobalt-based alloy coatings. Another two phases (Y₂O₃ and ?-Co) were found by adding nano-Y₂O₃. Without nano-Y₂O₃, rapid directional solidified microstructure of columnar dendrite appeared. Fine and short dendritic microstructure and columnar to equiaxed transition (CET) occurred by adding nano-Y₂O₃ particles. With the increase in amount of nano-Y₂O₃, fully equiaxed crystallization appeared and the formation mechanism was analyzed. The results also showed that the sub-microstructure of the coatings changed from dislocation to stacking fault by adding nano-Y₂O₃.     

Effect of α-Al2O3 on the properties of cold sprayed Al/α-Al2O3 composite coatings on AZ91D magnesium alloy

Composite coatings using pure Al powder blended with α-Al₂O₃ as feedstock were deposited on AZ91D magnesium alloy substrates by cold spray (CS). The content of α-Al₂O₃ in the feedstock was 25 wt.% and 50 wt.%, respectively. The effects of α-Al₂O₃ on the porosity, microhardness, adhesion and tensile strength of the coatings were studied. Electrochemical tests were carried out in neutral 3.5 wt.% NaCl solution to evaluate the effect of α-Al₂O₃ on the corrosion behavior of the coatings. The results showed that the composite coatings possessed lower porosity, higher adhesion strength and tensile strength than cold sprayed pure Al coating. The corrosion current densities of the composite coatings were similar to that of the pure Al coating and much higher than that of bare AZ91D magnesium alloy.     

Suspension plasma sprayed composite coating using amorphous powder feedstock

Al₂O₃-ZrO₂ composite coatings were deposited by the suspension plasma spray process using molecularly mixed amorphous powders. X-ray diffraction (XRD) analysis shows that the as-sprayed coating is composed of α-Al₂O₃ and tetragonal ZrO₂ phases with grain sizes of 26 nm and 18 nm, respectively. The as-sprayed coating has 93% density with a hardness of 9.9 GPa. Heat treatment of the as-sprayed coating reveals that the Al₂O₃ and ZrO₂ phases are homogeneously distributed in the composite coating.