次亚磷酸根离子在铂电极上氧化的机理研究(英文)

用SNIFTIRS和循环伏安法研究次亚磷酸根离子在多晶铂电极上的电氧化机理 .分析了0 .5mol/LH2 SO4 + 0 .1mol/LNaH2 PO2 溶液中原位红外反射谱图与Pt电极电位的关系 ,发现次亚磷酸根离子在Pt上发生解离吸附 ,其氧化产物是H3 PO4 ,不同于在Ni上的氧化产物H2 PO- 3 ,据此提出了酸性溶液中次亚磷酸根离子在Pt上氧化机理的新看法     

Pt-Mo2C/GC催化甲醇氧化的现场电化学-红外光谱研究

应用离子交换法制备了40%Pt在Mo2C/GC上的电催化剂.X射线衍射(XRD)显示,Pt在Mo2C载体上有较好的分散度,平均粒径为3 nm.循环伏安、计时电位测试表明,酸性溶液中,Pt-Mo2C/GC具有良好的甲醇氧化性能.其催化甲醇氧化的起始电位比Pt/C的负移了90 mV.这一优异性能与Pt和载体Mo2C之间的协同作用有关.现场红外光谱电化学测量显示,甲醇在Pt/C电极氧化的中间产物是桥式吸附COB和线性吸附COL,而在Pt-Mo2C/GC电极则未检测到有害中间产物CO,其氧化终产物均为CO2.     

乙醇和CO在Pt-WO3/C电极上的电催化氧化

制备并比较了Pt/C和Pt-WO3/C催化剂对乙醇的电化学氧化活性.发现无论是在酸性溶液中还是中性溶液中,Pt-WO3/C电极对乙醇氧化的电催化活性都比在Pt/C电极上高.这是由于WO3能提供乙醇在Pt上氧化所需的含氧物种,此外WO3能在较低电位下使乙醇氧化的中间产物CO氧化除去,从而提高了催化剂对乙醇氧化的催化活性.     

高铁酸盐在SnO2-Sb2O3/Ti电极上的选择性电化学合成

合成了SnO2-Sb2O3/Ti电极材料.实验结果证实,在14mol/LNaOH水溶液中和完全避免析氧反应的条件下,Fe(Ⅱ)物种在该电极上进行电化学氧化并生成FeO42-.结果表明,Fe(OH)3在浓NaOH溶液中发生酸式电离,形成可溶于水的FeO2-,该离子的浓度随着碱溶液浓度变化而发生明显变化,而且它还是发生化学氧化和电化学氧化的反应物.在SnO2-Sb2O3/Ti电极上,FeO42-的电化学还原起始电位为0.38V(vs.Hg/HgO,14mol/LNaOH),FeO2-电化学氧化起始电位为0.54V.结果还表明,用电化学方法氧化Fe(Ⅱ)物种生成FeO42-是个多步骤过程.     

Pt及其修饰电极上甲醇吸附和氧化的CV和EQCM研究

运用电化学循环伏安和石英晶体微天平 (EQCM )研究了 0 .1mol·L- 1H2 SO4 溶液中甲醇在Pt电极和以Sb ,S不可逆吸附原子修饰的Pt(Pt/Sbad和Pt/Sad)电极上的吸附和氧化过程 .结果表明甲醇的氧化与电极表面氧物种有着极其密切的关系 .Pt电极表面Sb吸附原子能在较低的电位下吸附氧 ,可显著提高甲醇电催化氧化活性 .与Pt电极相比较 ,Sb吸附原子修饰的Pt电极使甲醇氧化的峰电位负移了 0 .13V .相反 ,Pt电极表面S吸附原子的氧化会消耗表面氧物种 ,抑制了甲醇的电氧化 .本文从表面质量变化提供了吸附原子电催化作用的新数据     

Pt/巯基乙酸/玻碳电极的表面形貌与电催化性能

以巯基乙酸为偶联层在玻碳(GC)电极上组装 Pt纳米颗粒, 得到Pt /巯基乙酸/GC电极, 利用扫描电镜(SEM)和循环伏安法(CV)研究了不同条件下复合电极的表面形貌和电化学性能. 研究结果表明, 巯基乙酸在GC电极表面具有特性吸附, 形成了具有一定致密性的吸附层. 在0.5 mol/L H2SO4+1.0 mol/L CH3OH溶液中, 组装19 h的复合电极对甲醇氧化表现出较好的电催化性能.     

碳纳米管负载纳米铂修饰电极及电催化氧化H2O2的研究

采用化学气相沉积法在碳纳米管(CNT)上负载Pt纳米颗粒,并制备了CNT-Pt修饰玻碳电极(CNT-Pt/GCE).研究了该修饰电极在磷酸缓冲液中对H2O2的电催化氧化作用以及实验条件的影响.计算了H2O2在CNT-Pt/GCE上的电极反应速率常数.结果表明,CNT-Pt/GCE对H2O2的电化学氧化具有良好的催化作用,电极反应速率常数比铂电极高约2.65倍.初步探讨了电催化氧化机理,为酶电化学传感器的研制提供了一条新的途径.     

Pt电极上Sb，S吸附原子对正丁醇电催化氧化性能的影响

运用电化学循环伏安和石英晶体微天平研究了0.1 mol/L H2SO4 溶液中正丁醇（1-BL）在Pt电极和以Sb，S吸附原子修饰的Pt（Pt/Sbad和Pt/Sad）电极上电催化氧化过程。从电极表面质量变化表明正丁醇的氧化与电极表面氧物种有着极其密切的关系。Pt电极表面Sb吸附原子能在较低的电位下吸附氧，可显著提高正丁醇电催化氧化活性。与Pt电极相比较，Sb吸附原子修饰的Pt电极使正丁醇氧化的峰电位负移了0.33 V，峰电流增大了近一倍。相反，Pt电极表面S吸附原子的氧化会消耗表面氧物种，抑制了正丁醇的电氧化。本文从表面质量变化提供了吸附原子电催化作用的新数据。     

抗坏血酸在PPy-HEImTfa/Pt电极上的电催化氧化及其机理

以铂为基底电极,在1-乙基咪唑三氟乙酸盐(HEImTfa)离子液体中电化学合成导电聚吡咯(PPy),制得PPy-HEImTfa/Pt电极;采用循环伏安法研究了PPy-HEImTfa/Pt电极对抗坏血酸的电催化氧化性能.结果表明:PPy-HEImTfa/Pt电极对0.1mo·lL-1抗坏血酸具有较高的电催化氧化活性,与相同条件下硫酸溶液中在铂表面修饰的聚吡咯(PPy-H2SO4/Pt)电极和裸铂电极相比,其氧化峰电位分别降低了0.10和0.19V,氧化峰电流分别增加了3.0和3.6mA.同时采用原位傅里叶变换红外(insitu FTIR)光谱技术对抗坏血酸在PPy-HEImTfa/Pt电极上的电氧化机理进行了研究,结果表明:抗坏血酸在PPy-HEImTfa/Pt电极上首先被氧化为脱氢抗坏血酸,在水溶液中脱氢抗坏血酸迅速发生水合作用形成水合脱氢抗坏血酸,它进一步水解并发生内酯开环反应生成2,3-二酮古洛糖酸;在较高电位下,部分抗坏血酸最终被氧化成CO2.     

甲醇在欠电位沉积Ru修饰Pt电极上的催化氧化

采用欠电位沉积(upd)方法在Pt 表面沉积亚单层的Ru制备出upd-Ru/Pt 电极. 通过欠电位沉积前后电极在0.5 mol·L-1 H2SO4溶液中循环伏安图-152 - 128 mV(vs Ag/AgCl)电位范围内对氢区的数值积分确定Pt表面Ru 的覆盖度. 用电化学方法测试了甲醇在upd-Ru/Pt电极上的催化氧化, 并讨论分析了欠电位沉积电位和Ru的表面覆盖度对甲醇氧化的影响. 结果表明, Ru能够欠电位沉积到Pt表面. Pt表面欠电位沉积少量的Ru 即能大大促进甲醇的氧化.只要控制upd-Ru的沉积量, upd-Ru原子就能大大促进甲醇氧化而与沉积电位无关. Ru原子对甲醇氧化的促进作用与Ru和Pt是否形成合金无关, 而取决于Ru 在Pt表面的百分含量.     

次亚磷酸根离子在多晶铂电极上氧化的原位红外光谱研究

次亚磷酸根离子在多晶铂电极上氧化的原位红外光谱研究;电氧化;电催化;SNIFTIRS     

铂电极上苯和苯磺酸吸附定向的现场红外反射吸收光谱电化学方法研究

本文用现场红外反射吸收光谱电化学方法和循环伏安法研究铂电析上苯和苯磺酸的吸附定向。对于苯/铂势系, 电势在-0.6至0.0V(相对饱和甘汞电极)内, 苯主要以垂直方式吸附; 在0.0至0.8V内则主要以平躺方式吸附。对于苯磺酸/铂体系,电势在-0.4V至0.0V内, 苯磺酸分子中的苯环主要呈垂直吸附且SO~3H基团远离电极表面; 在0.0至1.0V内则主要以倾斜平躺方式吸附, SO~3H基团通过其中的两个氧原子吸附于电极表面上。     

SFG study of the ethanol in an acidic medium--Pt(110) interface: effects of the alcohol concentration

Ethanol in an acidic solution-Pt(110) interface was studied by SFG spectroscopy (between 1820 and 2325 cm(-1)) to explore primarily the effects of the alcohol concentration. Stretching bands of H-Pt (ca. 1970 or 2050 cm(-1)) and CO (ca. 1980 and 2040 cm(-1)) species, produced by the ethanol oxidation, were detected during the adsorption and oxidation of 0-1 mol L(-1) ethanol in a 0.1 mol L(-1) HClO(4) solution on the electrode surface. Hydrogen and CO coadsorb stably on Pt(110) between 0.05 and 0.15 V in ethanol-containing solutions. In this potential range, the blue shift of the hydrogen resonance (ca. 80 cm(-1)) reveals a weakening of the hydrogen bonding between adsorbed hydrogen and water molecules in the double layer. After the hydrogen desorption (0.15 V), the formation of compact CO islands, depending on the ethanol concentration, lifts the Pt(110) surface reconstruction. In ethanol-free solution, the surface remains reconstructed. The lower-frequency CO band is assigned to the CO species adsorbed on (1 x 2) reconstructed Pt(110) domains, having smaller local coverages, while the higher-frequency CO band is attributed to the close-packed CO species adsorbed on (1 x 1) patches. The reaction pathway forming CO(2) is less favored with increasing ethanol concentration.     

Pt电极表面及附近水行为的现场红外反射吸收光谱电化学初探

本文用现场红外反射吸收光谱电化学方法和循环伏安法研究了Pt电极表面及附近水的行为. 据不同范围内得到的SNIFTIRS 谱中水峰的变化提出了三种可能的解释: (A)电极上水的吸附取向的改变; (B)电极附近水分子的长程有序的变化; (C)电极上水的氧化及还原, Pt-O化合物的形成导致薄层中水量的减少。     

碱性介质中甘氨酸在Pt电极上解离吸附和氧化反应的原位红外反射光谱研究

运用原位红外反射光谱研究了碱性介质中甘氨酸在Pt电极上的解离吸附和氧化反应行为,并利用纳米Pt膜电极的异常红外效应鉴定反应过程中生成的表面吸附物种.结果表明:甘氨酸在Pt电极上极易发生解离,生成强吸附于电极表面上的氰基负离子,该吸附物种在低于0V电位下能稳定存在,并抑制甘氨酸的进一步反应.当电位高于0.2V时,氰基负离子被氧化为氰酸根离子进入溶液,使甘氨酸发生氧化反应,生成氰酸盐和碳酸盐等产物.     

Influence of tin on the oxidation of methanol on a platinum electrode

The influence of adsorbed tin and tin(IV) ions on the oxidation of methanol chemisorbed species as well as the methanol from the bulk of the solution was studied on a Pt electrode by voltammetric and radiometric methods. It was found that tin is not adsorbed as an ad-atom but rather as a divalent ion. Enhancement of the electrocatalytic oxidation of chemisorbed species derived from methanol was observed only in the potential range from 0.4 to 0.8 V. The influence of some factors on the electrocatalytic properties of platinum is discussed.     

In-situ flow-cell IRAS observation of intermediates during methanol oxidation on low-index platinum surfaces.

Structural effects on intermediate species of methanol oxidation are studied on low-index planes of platinum using in-situ infrared (IR) spectroscopy. A flow cell is designed for rapid migration of reactant and product species on the electrode surface. IR spectra show adsorption of formate and the formation of carbonate species on the Pt(111) surface at potentials higher than that of CO oxidation. The band assignments for carbonate and formate are confirmed by vibrational isotope shifts. On Pt(100), the absorption band of adsorbed formate is much smaller than that on Pt(111). On the other hand, there is no adsorbed formate on Pt(110) in the potential region examined. The band intensity of formate follows the order: Pt(111)>Pt(100)>Pt(110). This order is opposite to that of the current density in the regions of higher potential. Adsorbed formate on Pt(111) behaves like a catalyst-poisoning intermediate, like adsorbed CO.     

Adsorbed intermediates of formaldehyde oxidation and their role in the reaction mechanism

Formaldehyde oxidation was studied on the basal planes of platinum single crystals. Electrochemical and IR spectroscopy data give new information on the mechanism of oxidation. Formaldehyde oxidation at platinum electrodes is a surface-sensitive reaction. From the three basal planes of Pt(hkl), Pt(111) is the most active one. The less active surfaces Pt(100) and Pt(110) are blocked by adsorbed carbon monoxide at the initial stages of the reaction as the formaldehyde is admitted in the solution with the electrode polarized at 0.05 V. Besides CO(ad), other adsorbed species are formed. From these, methylene glycolate, H2COO(ad), is the intermediate of the fast oxidation pathways forming CO2 and HCOOH as soluble products. According to IR data the yields of soluble products at Pt(111) were calculated at 0.6 V, giving 63% for HCOOH and 37% for CO2. At 0.05 V the Pt(111) surface becomes slowly blocked by CO(ad), as observed when the electrode was left in contact with the formaldehyde solution over a period of several minutes. The same blockage occurs during a cyclic voltammogram, which causes a lowering of activity during the second potential scan. A general scheme of the reaction is proposed.     

硫酸溶液中Pt电极表面过程的EQCM研究

应用电化学循环伏安和石英晶体微天平(EQCM)方法研究了0.1mol·L-1硫酸溶液中Pt电极表面的吸附和氧化过程.从电极表面质量变化的结果分析,可认为正向电位扫描时氢区表面质量的增加是由于水分子取代Had引起的,而双电层区的质量增加则是由于水的吸附模式逐渐由氢端吸附转向氧端吸附所致.根据频率变化和电量数据,进一步推算出水在双电层区是以低放电吸附形式出现的,1molPt原子和水分子只发生0.054mol的电荷转移.本文结果可为认识Pt电极表面过程提供定量的新数据.