硫镓银晶体的化学腐蚀研究

采用改进的垂直布里奇曼(Bridgman)法自发成核生长AgGaS2晶体,在生长初期对生长安瓿籽晶袋进行上提回熔,生长出外观完整、无裂纹的大尺寸AgCaS2单晶体.采用XRD对晶体进行分析,获得了(112)、(001)和(101)面的高强度尖锐衍射峰.采用不同配比的腐蚀剂对晶体(101)、(112)及(001)晶面进行化学腐蚀,然后采用金相显微镜和扫描电镜观察,结果显示,(101)晶面蚀坑为清晰的近似三角形的四边形蚀坑,(112)晶面蚀坑为清晰的近似三角锥形,(001)晶面则呈现互相垂直的腐蚀线.初步分析了不同蚀坑的形成原因,计算出(101)和(112)面蚀坑密度约为105/cm2数量级.结果表明,改进方法生长出的大尺寸AgGaS2单晶体结构完整、位错密度低,质量较好.     

CdZnTe晶体的缺陷能级分析

通过测试富Cd原料无籽晶垂直布里奇曼法生长出的高阻Cd0.8Zn0.2Te (CZT)单晶体的I-T特性曲线,利用热激活能原理来分析单晶体内的缺陷,结果得到晶体中有一个由镉空位引起的电子陷阱,其深度为0.539eV.由于俘获能级有较高的激活能,在常温下,价带上的载流子不会被激发,所以该晶体适用于制作室温核辐射探测器.另外还研究了CZT晶体在室温下的I-V特性,测得采用该方法生长的CZT单晶体电阻率高达5.0×1010Ω*cm,制作的核辐射探测器在室温下获得了比较好的241Am 59.5keV能谱.     

硫镓银晶体(112)面蚀坑形貌研究

本文报道了一种能在室温下对硫镓银晶体(112)面进行择优腐蚀的新腐蚀液配方,采用新腐蚀液对改进的Bridgman法生长的AgGaS2晶体进行腐蚀,用扫描电镜对蚀坑进行了观察,得到了清晰的(112)面蚀坑形貌,形状为三角锥形.初步解释了蚀坑的形成原因.AgGaS2晶体低指数的{100}面的腐蚀速度较慢,在腐蚀过程中逐渐显露出来,最终使晶体(112)面呈现出三角锥形蚀坑形貌.     

CdSe单晶体的生长及其特性研究

本文报道了用改进的垂直气相法(多级提纯垂直气相法)生长富Cd的CdSe单晶体,并对晶体的性能进行了观测,其电阻率为107Ωcm量级,电子陷阱浓度为108cm-3量级,第一次报道了(110)面的腐蚀形貌。结果表明：采用这种方法制备CdSe单晶,设备简单,易于操作,在提纯和生长过程中不需要转移原料,有利于减少晶体中的杂质含量,降低位错密度,改善晶体的电学性能。多级提纯垂直气相法是一种有前途的CdSe单晶体生长的新方法。     

pH值对KDP晶体位错结构的影响

在一定的过饱和度下,分别用点状和片状籽晶在不同pH值溶液中生长出了KDP晶体.利用化学腐蚀法对KDP晶体的不同晶面进行了腐蚀,得到了清晰的位错蚀坑.应用光学显微镜对位错蚀坑的分布特点和密度做了观察分析,发现很多位错蚀坑成线状排布.pH值对KDP晶体位错密度有较大影响,低pH值条件下生长出的晶体位错密度较大.测试了KDP晶体样本的透过率,结果表明位错密度对KDP晶体的透过率没有明显的影响.     

L-精氨酸掺杂下ZTS溶液的稳定性研究

研究了L-精氨酸掺杂下硫脲硫酸锌(ZTS)溶液中的成核过程,测量了在不同掺杂浓度下ZTS溶液的亚稳区和诱导期.结果表明:随掺杂浓度的增加,溶液的亚稳区变宽,诱导期增大;根据经典成核理论计算了晶体的成核热、动力学参数,分析了溶液稳定性与掺杂浓度的关系,即随着L-精氨酸掺杂浓度的增加,溶液的稳定性得到明显提高.利用化学腐蚀法对ZTS晶体(100)面进行了腐蚀,并用光学显微镜对腐蚀面进行观察,得到了清晰的位错蚀坑.当L-精氨酸掺杂浓度为1.5mol;时,ZTS晶体(100)面位错蚀坑密度最小,适合高光学质量晶体的生长.     

硒铟镓银单晶体(112)面蚀坑形貌观察

研究出一种能在室温下对AgGa0.8In0.2Se2晶体(112)面进行择优腐蚀的新腐蚀液配方,提出了一种适合AgGa0.8In0.2Se2晶体择优腐蚀的新工艺。采用改进的Bridgman法生长出AgGa0.8In0.2Se2晶体,对晶体进行定向切割出(112)面晶片;然后对晶片进行研磨、机械抛光,使其表面平整无划痕;再将晶片用新腐蚀液,浓HNO3(65%～68%)∶浓HCl(35%～38%)=1∶2.5(体积比),在室温下腐蚀5min,同时进行超声振荡。采用金相显微镜对腐蚀后的晶片表面进行观察,发现清晰的蚀坑形貌,形状近似为正三角形,并对(112)面蚀坑的形成及其形貌成因进行了理论分析。     

用提拉法生长的GdCa4O(BO3)3晶体的结构缺陷研究

利用相衬显微镜结合化学腐蚀法,进行了沿 010 方向提拉生长的GdCa4O(BO3)3(GdCOB)晶体中的缺陷观察.发现位错是 010 方向生长的晶体中的重要缺陷.在不同方向的晶体切片上观察了螺位错和刃位错蚀坑,位错塞积,平底蚀坑及尖底蚀坑.位错密度随晶体长度的变化而变化.在晶体的尾部观测到位错密度为103/cm2,而在晶体的初始部位位错密度很低,只有40/cm2.在晶体的X,Z及 401 方向的切片的正反两面观察到的位错蚀坑现象完全不同,可以认为GdCOB晶体为单畴极性晶体,自发极化方向沿z轴方向.     

磷锗锌单晶体的腐蚀研究

报道了一种新的ZnGeP2晶体择优腐蚀剂及其腐蚀工艺,即先采用研磨、物理机械抛光和HCl+HNO3热化学抛光获得表面平整无划痕的ZnGeP2晶片,然后将晶片在室温下采用HF(40;):HNO3(65;):CH3COOH(99.5;):H2O:I2=2 mL:2 mL:1 mL:1 mL:4 mg腐蚀剂超声振荡腐蚀8 min;在扫描电镜下观察到ZGP(110)和(204)晶面的腐蚀坑,蚀坑形貌清晰,具有立体感,(110)晶面蚀坑呈四边形,(204)晶面蚀坑呈五边形,取向一致,蚀坑密度(EPD)约为104/cm2.从理论上对蚀坑形貌的形成机理进行了分析.     

无籽晶化学气相法生长ZnO晶体

采用化学气相法自发成核的方式生长出φ4mm×5 mm ZnO单晶体.分析了化学气相输运机制,获得ZnO-C体系在生长过程中的压强为0.43 MPa,确定以扩散传输为主;设计了新的生长石英安瓿(锥角约为35°),让沿较快面生长的晶核能淘汰其他晶胚,易长大并形成单晶;X射线衍射测试晶体生长显露面为(002)面,其回摆曲线半峰宽为18arcsec;六边形的腐蚀蚀坑确定该面为ZnO(001)的Zn面,位错缺陷密度为103 cm-2量级.晶体在368 nm处出现了较强的紫外发光峰,属带边激子跃迁;紫外透过率在450～1000 nm内达65;,截止波长为390 nm,对应禁带宽度约为3.12 eV.结果表明,采用无籽晶化学气相法生长的ZnO晶体结晶度好,质量较高.     

Evidence of slip in calcium fluoride single crystals

Natural single crystals of calcium fluoride have been cleaved along (111) planes and the cleavage faces have been etched in 0.2 N nitric acid solution. Etching produces rows of equally spaced etch pits running in <110>directions. One-to-one correspondence of glide bands has been established on the matched faces and on the three different flakes of the same crystal. This is further confirmed by studying the rosette structure produced on a (111) cleavage plane by indenting that plane itself. The active slip planes are found to be {110}. The implications are discussed.     

X-ray topographic investigation of growth defects in natural calcium fluoride crystals

Calcium fluoride crystals have been cleaved along {111} faces and the freshly cleaved faces have been chemically etched in 2.6 N nitric acid solution. The etched faces have been optically studied. One-to-one correspondence of dislocation etch pits have been established on the matched cleavage faces and on the opposite sides of thin flakes. The same crystal has been studied using X-ray topographic technique. By using 022 - and 02 2 reflections, stereopair projection topographs were studied and compared with the optical micrographs. The close resemblance between dislocation etch pits and dislocation out-crop images has been established. The orientation of the Burgers vectors of the dislocation lines has been identified using AgKα radiation with 111 -, 11 1- and 1 11 reflections. It has been confirmed that Burgers vectors of dislocation lines lie parallel to 〈110〉 directions. The implications are discussed.     

Ca0．80Zn0．20Te晶体的生长及性能研究

用本实验室合成的Ca0．80Zn0．20Te多晶料为原料，采用改进的布里奇曼法在镀碳和未镀碳的石英安瓿中生长出Ca0．80Zn0．20Te晶锭。使用X射线衍射仪对合成产物及晶锭进行了分析，生长晶体的X射线衍射峰尖锐，摇摆谱对称，表明晶锭的结晶性能较好；用IRPrestige-21红外光谱仪分析了晶体的红外透射光谱，测试结果表明安瓿镀碳后生长的晶体位错密度小，均匀性较好，电阻率优于未镀碳安瓿生长的晶体；晶体的蚀坑密度在10^3-10^4cm^-2之间，比未镀碳安瓿生长的晶体低1个数量级。     

Inclined Dislocations in Synthetic Calcite Crystals

A large number of perfect (100) cleavages were obtained by cleaving the laboratory grown synthetic calcite crystals. By etching such cleavages in 20% ammonium chloride solution, it is established that the pits indicate the sites of dislocations in the crystals. This is further confirmed by comparing the etch patterns on matched cleavage surfaces. Eccentricity of the pits has been attributed to the inclined nature of dislocations. Existence of parallel dislocations seems to be due to the purity of the crystal. These observations are verified by comparing etch patterns produced on opposite faces of a thin flake (0.048 mm thick) and also by successive etching and polishing a cleavage surface. It is conjectured that curl-bottomed pits nucleate at the sites of screw dislocations in the crystal. The implications are discussed.     

Shape of thermal etch pits and crystal structure in tellurium crystals

During the systematic study of thermal etching of tellurium crystals, various shaped thermal etch pits were observed on the {101 0} cleavage faces of this crystal. An attempt has been made to explain the shape of non-dislocation and dislocation etch pits. A simple model based on crystal structure and bonding of atoms has been suggested to explain the shape of etch pits.     

Beiträge zum Ätzen von Galliumarsenid (I) Strukturtheoretische Diskussion der erzeugten Ätzmorphologien

{111}-, {110}- and {100}-plates of GaAs have been etched in various etching solutions followed by comparing the obtained etching structures. The fundamentals of the discussion is the existing correlation between the morphology of etch pits and crystal structure. It is shown that a qualitative interpretation of the manifold etching phenomena on the above faces in a structure characteristic for GaAs can be given by including 1. the presence of primary defects as a constitutive property of real crystals and 2. the consideration of recordable influences of the surroundings.     

Surface structures of fluorite crystals

Optical studies have been made of the microstructures on the natural {100} and {111} faces of natural fluorite crystals. The protrudance of triangular elevations, growth pyramids, and natural etch pits have been observed on a large number of crystals. It is suggested that fluorite crystals grown by two-dimensional spreading and piling of growth layers parallel to {100} faces. The natural etch pits on {100} and {111} faces suggest that they have been produced as a result of a dissolution process in nature. The natural faces have been etched in the laboratory and it is established that the pits indicate the existence of linear defects in the crystals. The implications are discussed.     

Cd0.80Zn0.20Te晶体的生长及性能研究

用本实验室合成的Cd0.80Zn0.20Te多晶料为原料,采用改进的布里奇曼法在镀碳和未镀碳的石英安瓿中生长出Cd0.80Zn0.20Te晶锭。使用X射线衍射仪对合成产物及晶锭进行了分析,生长晶体的X射线衍射峰尖锐,摇摆谱对称,表明晶锭的结晶性能较好;用IRPrestige-21红外光谱仪分析了晶体的红外透射光谱,测试结果表明安瓿镀碳后生长的晶体位错密度小,均匀性较好,电阻率优于未镀碳安瓿生长的晶体;晶体的蚀坑密度在103~104cm-2之间,比未镀碳安瓿生长的晶体低1个数量级。