The disinfection effect of a novel continuous-flow water sterilizing system coupling dual-frequency ultrasound with sodium hypochlorite in pilot scale

In this paper, a self-designed novel continuous-flow water disinfection system coupling dual-frequency ultrasound (US) with chemical disinfectant sodium hypochlorite (NaClO) was tested in a pilot scale using a simulated effluent containing Bacillus subtilis (B. subtilis), one of the indicators of water treatment efficiency. A suspension having a B. subtilis concentration of approximately 10⁴ CFU/mL was introduced into the system to (1) investigate disinfection efficiency of US pretreatment with NaClO (US + NaClO) and simultaneous US and NaClO (US/NaClO) disinfection under different single frequencies; (2) further examine the disinfection efficiency of these two processes with dual-frequency US; and (3) identify dosage reduction of chlorine in this disinfection system. The results demonstrated that lower dual-frequency (17 kHz + 33 kHz) US pretreatment with NaClO disinfection and simultaneous higher dual-frequency (70 kHz + 100 kHz) US and NaClO were beneficial to bacterial inactivation in terms of sterilizing efficiency. It has also been observed that US pretreatment with lower combination of 17 + 33 kHz frequencies showed better enhancement in which log reduction reached to 3.82 after 10 min chlorine reaction (chlorine alone was 0.22 log reduction), nearly 1 log reduction higher than single frequencies at the same constant power. Consequently, at equivalent power dissipation levels, US of lower frequencies combination pretreatment with NaClO disinfection performed such a promising process that one-thirds (from 12 mg/L NaClO reduced to 8 mg/L NaClO) of the required NaClO dosage was reduced for the ideal disinfection efficiency of 4 log reduction, namely 100% disinfection. And the utilization efficiency of NaClO was increased from 37.67% to 85.25% in 30 min of treatment time using an optimized combination of pretreatment and chlorination.     

Characterization of suspensions of particles in water by an ultrasonic resonant cell

This paper presents a resonant technique to accurately measure phase-velocity and attenuation of longitudinal acoustic waves in suspensions of solid particles in water. The technique is based on exciting thickness resonances of a layer of fluid and analyzing its spectrum. To this end, a resonant cell to contain the fluid is described and used. Two different type of water suspensions are studied: titanium dioxide and alumina particles; particle volume fraction is in the range 0–0.18. Simultaneous determination of particle size distribution in the suspension by an optical method are also carried out. Finally, the experimental results are compared with theoretical predictions obtained from three different approaches.     

Degradation of phenol using a combination of ultrasonic and UV irradiations at pilot scale operation

In the present work, combination of ultraviolet (UV) irradiations (using 8 W UV tube) with ultrasonic (US) irradiations (rated power 1 kW and frequency of 25 kHz) has been investigated for the degradation of phenol at pilot scale of operation. Different modes of operation viz. UV alone, US alone, UV/US, UV/TiO₂ (photocatalysis), UV/H₂O₂, UV/NaCl, UV/US/TiO₂ (sonophotocatalysis) and H₂O₂ assisted sonophotocatalysis have been investigated with an objective of maximizing the extent of phenol degradation. Effect of presence of hydrogen peroxide and sodium chloride at a concentration of 10 g/l and TiO₂ over a range of 0.5–2.5 g/l has been investigated. It has been observed that 2.0 g/l of TiO₂ is the optimum concentration, beyond which a decrease in the extent of degradation is observed. Maximum extent of degradation of phenol was 37.75% for H₂O₂ assisted photosonocatalysis at pH of 2. The present work is first of its kind to report the use of combined ultrasonic and UV irradiations at pilot scale operation and obtained results should induce some degree of certainty in proposed industrial applications of sonochemical reactors for wastewater treatment.     

The development and evaluation of electrolysis in conjunction with power ultrasound for the disinfection of bacterial suspensions

There is an increasing incidence in health problems related to environmental issues that originate from inadequate treatment of potable waters. This has compelled scientists and engineers to engage in innovative technologies to achieve a maximum disinfection at affordable costs. Some species of bacteria produce colonies and spores that can agglomerate in spherical clusters and thus protect organisms on the inside of the cluster against biocidal attack. Flocs of fine particles (e.g., clay) can entrap bacteria and this can also protect them against the biocides. Other bacteria have the ability to mutate, thus building up resistance to conventional biocides (e.g., chlorine).Ultrasound has been shown to be effective in improving the effectiveness of biocides such as chlorine. The aim of this present study was to investigate the effect of electrolysis and power ultrasound as a disinfection treatment and to provide a greater knowledge of the fundamentals of disinfection through the production of hypochlorite in situ from saline solution via electrolysis. The electrode materials investigated were, carbon (felt and graphite), copper and stainless steel rods. The results show that sonication appears to amplify the effect of electrolysis. A combination of both treatments is significantly better than sonication or electrolysis alone.     

Travel-time tomography in shallow water: experimental demonstration at an ultrasonic scale

Acoustic tomography in a shallow ultrasonic waveguide is demonstrated at the laboratory scale between two source-receiver arrays. At a 1/1,000 scale, the waveguide represents a 1.1-km-long, 52-m-deep ocean acoustic channel in the kilohertz frequency range. Two coplanar arrays record the transfer matrix in the time domain of the waveguide between each pair of source-receiver transducers. A time-domain, double-beamforming algorithm is simultaneously performed on the source and receiver arrays that projects the multi-reflected acoustic echoes into an equivalent set of eigenrays, which are characterized by their travel times and their launch and arrival angles. Travel-time differences are measured for each eigenray every 0.1 s when a thermal plume is generated at a given location in the waveguide. Travel-time tomography inversion is then performed using two forward models based either on ray theory or on the diffraction-based sensitivity kernel. The spatially resolved range and depth inversion data confirm the feasibility of acoustic tomography in shallow water. Comparisons are made between inversion results at 1 and 3 MHz with the inversion procedure using ray theory or the finite-frequency approach. The influence of surface fluctuations at the air-water interface is shown and discussed in the framework of shallow-water ocean tomography.     

Dichroism of bacterial suspensions in electrical fields

Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 52, No. 6, pp. 978–983, June, 1990.     

Study on the changes of ultrasonic parameters over supercritical Ni-Co electroplating process

This work discusses the influence of changes to ultrasound (US) parameters over the nickel cobalt (Ni-Co) metal thin film properties produced by supercritical CO₂ (SC-CO₂) electroplating. Additionally, Ni-Co films were produced by conventional electroplating and silent SC-CO₂ and compared against each other.The discussion on metal thin film properties revolves around variations to the bath type ultrasonic power (15 W and 20 W) and frequency (42 k Hz and 72 kHz) during experiments. The properties provided by the three electroplating processes and analyzed include: grain sizes, film elemental content analyses, surface microstructures, film hardness, corrosion resistance, surface roughness, crystalline structure and preferential growth, etc. From the results it was clear that quality of films produced by US-SC-CO₂ was improved compared to that of films produced by silent SC-CO₂, which itself was better than those produced by conventional electroplating. However, when US power was varied we observed a decline in the mechanical properties of the produced films.The combination of ultrasonic agitation with SC-CO₂ allows for improved mechanical properties such as: lower surface roughness, finer grain size and surface morphologies, increased corrosion resistance and film hardness. The ultrasound agitation applied to SC-CO₂ electroplating enhanced the formation of alloyed metal as ultrasonic agitation increased the electrolyte flowability during electroplating process resulting in increased mass transfer while at the same time achieving a surface cleaning effect which removed metal ions with poor adhesion and other unwanted particles. Moreover, application of ultrasonic agitation avoids the use of surfactants so only changes to the physical phenomena and no changes to the chemical composition of the deposited thin films were observed, meaning less pollution to the electrolyte and higher purity of the deposited films.The US-SC-CO₂ electroplating method described in this work effectively enhanced the mechanical properties of the deposited thin films compared to those produced by both silent SC-CO₂ and conventional electroplating processes.     

Scattering of ultrasonic shock waves in suspensions of silica nanoparticles

Experiments are carried out to assess, for the first time, the validity of a generalized Burgers' equation, introduced first by Davidson [J. Acoust. Soc. Am. 54, 1331-1342 (1973)] to compute the nonlinear propagation of finite amplitude acoustical waves in suspensions of "rigid" particles. Silica nanoparticles of two sizes (33 and 69 nm) have been synthesized in a water-ethanol mixture and precisely characterized via electron microscopy. An acoustical beam of high amplitude is generated at 1 MHz inside a water tank, leading to the formation of acoustical shock waves through nonlinear steepening. The signal is then measured after propagation in a cylinder containing either a reference solution or suspensions of nanoparticles. In this way, a "nonlinear attenuation" is obtained and compared to the numerical solution of a generalized Burgers' equation adapted to the case of hydrosols. An excellent agreement (corresponding to an error on the particles size estimation of 3 nm) is achieved in the frequency range from 1 to 40 MHz. Both visco-inertial and thermal scattering are significant in the present case, whereas thermal effects can generally be neglected for most hydrosols. This is due to the value of the specific heat ratio of water-ethanol mixture which significantly differs from unity.     

Evaluation of a biological wastewater treatment system combining an OSA process with ultrasound for sludge reduction

Sludge production is an undesirable by-product of biological wastewater treatment. The oxic-settling-anaerobic (OSA) process constitutes one of the most promising techniques for reducing the sludge produced at the treatment plant without negative consequences for its overall performance. In the present study, the OSA process is applied in combination with ultrasound treatment, a lysis technique, in a lab-scale wastewater treatment plant to assess whether sludge reduction is enhanced as a result of mechanical treatment. Reported sludge reductions of 45.72% and 78.56% were obtained for the two regimes of combined treatment tested in this study during two respective stages: UO1 and UO2. During the UO1 stage, the general performance and nutrient removal improved, obtaining 47.28% TN removal versus 21.95% in the conventional stage. However, the performance of the system was seriously damaged during the UO2 stage. Increases in dehydrogenase and protease activities were observed during both stages. The advantages of the combined process are not necessarily economic, but operational, as US treatment acts as contributing factor in the OSA process, inducing mechanisms that lead to sludge reduction in the OSA process and improving performance parameters.     

Size-selective separation of submicron particles in suspensions with ultrasonic atomization

Aqueous suspensions containing silica or polystyrene latex were ultrasonically atomized for separating particles of a specific size. With the help of a fog involving fine liquid droplets with a narrow size distribution, submicron particles in a limited size-range were successfully separated from suspensions. Performance of the separation was characterized by analyzing the size and the concentration of collected particles with a high resolution method. Irradiation of 2.4 MHz ultrasound to sample suspensions allowed the separation of particles of specific size from 90 to 320 nm without regarding the type of material. Addition of a small amount of nonionic surfactant, PONPE20 to SiO₂ suspensions enhanced the collection of finer particles, and achieved a remarkable increase in the number of collected particles. Degassing of the sample suspension resulted in eliminating the separation performance. Dissolved air in suspensions plays an important role in this separation.     

Electrodialytic desalination of brackish water: effect of process parameters and water characteristics

The aim of this work is to study the desalination of brackish water using a laboratory scale electrodialysis cell. The influence of several parameters, such as flow rates, initial feed concentration, applied voltage and circulation mode on process efficiency were studied. This efficiency is evaluated by the demineralization rate, ionic flux transport and current efficiency. In this study, experiments were carried out on synthetic brackish water solutions prepared from sodium chloride salts. The concentrations of these solutions are varying from 0.5 to 3 g L^?1. The process was applied for the treatment of real brackish water sample with total dissolved salts ～5 g L^?1. The concentrations of different species in the obtained treated water are below the amounts recommended by World Health Organization for drinking water.     

Classification of regimes determining ultrasonic cavitation erosion in solid particle suspensions

Although the factors that influence ultrasonic cavitation erosion in solid particle suspensions have been extensively studied, the role that solid particles play in the cavitation process remains poorly understood. The ultrasonic cavitation erosion of AISI 1045 carbon steel was studied in the presence of monodisperse silica particles (10–100 μm, 0.5–20 vol%) suspended in transformer oil. Based on our results, we propose an overview of the possible influencing mechanisms of particle addition for specific particle sizes and concentrations. Four major regimes, namely a viscosity-enhancing regime (V), a particle-impinging regime (I), a particle-shielding regime (S), and a nuclei-adding regime (A) are identified, and their dependence on suspended particle characteristics is analyzed. The VISA regimes, in essence, reflect the viscous and inertial effects of suspended particles, and the way in which particle–particle interactions and heterogeneous nucleation affect erosion. This regime-based framework provides a better understanding of the dominant factors controlling the erosive wear caused by cavitation in the presence of solid particles, and provides a guide for erosion prediction and prevention.     

Mechanical measurement of the parameters in a pseudo-stationary ultrasonic field in liquids

After recalling the formulae relating the energy density of a progressive wave with the sonic field parameters, the problem of deducing these parameters in a pseudo-stationary field is discussed. This field is produced in a ‘fixed force interferometer’ by two torsion balances; it is shown how to deduce from the radiation pressure, measured simultaneously at transducer and at reflector, the local pressure and velocity amplitudes, discussing the errors involved in treating pseudo-stationary fields as purely stationary.     

Selective ultrasonic treatment of perforation zones in horizontal oil wells for water cut reduction

A technique for treatment of perforation zones of horizontal oil wells for water cut reduction based on selective ultrasonic treatment was suggested. The technique involves online geophysical studies of horizontal wells, determination of treatment intervals based on these studies, selective ultrasonic treatment of the chosen interval and subsequent pump-out using a specially designed jet pump. The technology does not involve reduction of the flow in the well. The developed innovative technique of water cut reduction using selective ultrasonic treatment is studied within this article. Theoretical estimations and computer modeling revealed that the position of the downhole ultrasonic tool near the sidewall of the well leads to more homogeneous distribution of the induced acoustical field and wider penetration of the acoustical waves. The developed method was tested on a horizontal well in Western Siberia, which was characterized by high water cut. Based on geophysical studies only zones with low water and high oil production were treated, this lead to a decrease of the water cut by 20% and an increase of oil production by 91% after treatment of the test well.     

A model for phase transitions in a system of rod-like colloidal suspensions

The present paper describes an extension of the Maier-Saupe theory of liquid crystals to a system of charged interacting rods and shows that nematic to isotropic transitions can also be induced by increasing the charge on the rods. The effects of length of rod, concentration of salt and the volume fraction on the phase diagram are described. The concept of the charge-induced isotropic phase is described, and it is argued that the structure is expected to be glassy. Evidence to support these conclusions from the existing literature is presented.     

Geometrical parameters of a water dropwise cluster

A dropwise cluster is obtained over the surface of water heated to 65–100°C. The pair correlation function of drops in the cluster is constructed. The temperature dependences of the spacing between the drops, their diameter, and the altitude of their levitation over the water surface are measured.     

Propagation of ultrasonic waves in suspensions and emulsions 2. Relation between ultrasonic properties and certain characteristics of the medium

The results obtained in the measurement of ultrasound velocity and absorption coefficient in pigment suspensions merit an attempt to interpret the functional dependence of these ultrasonic properties on suspension concentration and dispersion degree.     

Hybrid hydrodynamic cavitation (HC) technique for the treatment and disinfection of lake water

Water reclamation from lakes needs to be accomplished efficiently and affordably to ensure the availability of clean, disinfected water for society. Previous treatment techniques, such as coagulation, adsorption, photolysis, ultraviolet light, and ozonation, are not economically feasible on a large scale. This study investigated the effectiveness of standalone HC and hybrid HC + H₂O₂ treatment techniques for treating lake water. The effect of pH (3 to 9), inlet pressure (4 to 6 bar), and H₂O₂ loading (1 to 5 g/L) were examined. At pH = 3, inlet pressure of 5 bar and H₂O₂ loadings of 3 g/L, maximum COD and BOD removal were achieved·H₂O₂ was observed to significantly improve the performance of the HC when used as a chemical oxidant. In an optimal operating condition, a COD removal of 54.5 % and a BOD removal of 51.5 % using HC alone for 1 h is observed. HC combined with H₂O₂ removed 64 % of both COD and BOD. The hybrid HC + H₂O₂ treatment technique resulted in a nearly 100% removal of pathogens. The results of this study indicate that the HC-based technique is an effective method for removing contaminants and disinfection of the lake water.     

Disinfection effect of a continuous-flow ultrasound/ultraviolet baffled reactor at a pilot scale

An ultrasound/ultraviolet (US/UV) baffled reactor was developed to fill the gap in ultraviolet (UV) disinfection associated with disinfection efficiency. According to the previously selected operational condition, a continuous-flow US/UV baffled reactor was continuously operated in a wastewater treatment plant at a pilot scale for nearly three months, and the disinfection influent and effluent were analyzed, including fecal coliforms, Escherichia coli, and fecal streptococci. The US/UV baffled reactor could guarantee a high effluent disinfection performance in terms of fecal coliforms removal even with the fluctuation of the secondary effluent. All the disinfected effluents satisfied the requirement of the “Pollutants Discharge Standard of Municipal Wastewater Treatment Plant in China” (fecal coliforms below 1000 CFU/L for class 1A), and 87% of the tested fecal coliforms concentration in the disinfected effluent was below 100 CFU/L, nearly eliminating all fecal coliforms. Further analysis of the E. coli and fecal streptococci showed the broad disinfection ability and high disinfection efficiency of the US/UV baffled reactor. The flexibility of the specific energy consumption for the disinfection system depends on the water quality.     

Creaming enhancement in a liter scale ultrasonic reactor at selected transducer configurations and frequencies

Recent research has shown that high frequency ultrasound (0.4–3 MHz), can enhance milkfat separation in small scale systems able to treat only a few milliliters of sample. In this work, the effect of ultrasonic standing waves on milkfat creaming was studied in a 6 L reactor and the influence of different frequencies and transducer configurations in direct contact with the fluid was investigated. A recombined coarse milk emulsion with fat globules stained with oil-red-O dye was selected for the separation trials. Runs were performed with one or two transducers placed in vertical (parallel or perpendicular) and horizontal positions (at the reactor base) at 0.4, 1 and/or 2 MHz (specific energy 8.5 ± 0.6 kJ/kg per transducer). Creaming behavior was assessed by measuring the thickness of the separated cream layer. Other methods supporting this assessment included the measurement of fat content, backscattering, particle size distribution, and microscopy of samples taken at the bottom and top of the reactor. Most efficient creaming was found after treatment at 0.4 MHz in single and double vertical transducer configurations. Among these configurations, a higher separation rate was obtained when sonicating at 0.4 MHz in a vertical perpendicular double transducer setup. The horizontal transducer configuration promoted creaming at 2 MHz only. Fat globule size increase was observed when creaming occurred. This research highlights the potential for enhanced separation of milkfat in larger scale systems from selected transducer configurations in contact with a dairy emulsion, or emulsion splitting in general.