Ultrasound enhances lipase-catalyzed synthesis of poly (ethylene glutarate)

The present work explores the best conditions for the enzymatic synthesis of poly (ethylene glutarate) for the first time. The start-up materials are the liquids; diethyl glutarate and ethylene glycol diacetate, without the need of addition of extra solvent. The reactions are catalyzed by lipase B from Candida antarctica immobilized on glycidyl methacrylate-ter-divinylbenzene-ter-ethylene glycol dimethacrylate at 40 °C during 18 h in water bath with mechanical stirring or 1 h in ultrasonic bath followed by 6 h in vacuum in both the cases for evaporation of ethyl acetate. The application of ultrasound significantly intensified the polyesterification reaction with reduction of the processing time from 24 h to 7 h. The same degree of polymerization was obtained for the same enzyme loading in less time of reaction when using the ultrasound treatment. The degree of polymerization for long-term polyesterification was improved approximately 8-fold due to the presence of sonication during the reaction. The highest degree of polymerization achieved was 31, with a monomer conversion of 96.77%. The ultrasound treatment demonstrated to be an effective green approach to intensify the polyesterification reaction with enhanced initial kinetics and high degree of polymerization.     

Effect of ultrasound on the solubility limit of a sparingly soluble solid

The influence of power ultrasound (20 kHz) on the rate of attainment of saturation of sparingly soluble benzoic acid in distilled water and in 24% (w/w) aqueous glycerol was experimentally investigated at 30 °C. The importance of proper temperature control of process vessel contents when it was irradiated with high ultrasonic power level settings was demonstrated. A method was proposed to calculate the volumetric mass transfer coefficient under non-isothermal conditions.     

Influence of ultrasonic condition on phase transfer catalyzed radical polymerization of methyl methacrylate in two phase system – A kinetic study

An ultrasonic condition assisted phase transfer catalyzed radical polymerization of methyl methacrylate was investigated in an ethyl acetate/water two phase system at 60 ± 1 °C and 25 kHz, 300 W under inert atmosphere. The influence of monomer, initiator, catalyst and temperature, volume fraction of aqueous phase on the rate of polymerization was examined in detail. The reaction order was found to be unity for monomer, initiator and catalyst. Generally, the reaction rate was relatively fast in two phase system, when a catalytic amount of phase transfer catalyst was used. The combined approach, use of ultrasonic and PTC condition was significantly enhances the rate of polymerization. An ultrasonic and phase transfer catalyzed radical polymerization of methyl methacrylate has shown about three fold enhancements in the rate compared with silent polymerization of MMA using cetyltrimethylammonium bromide as PTC. The resultant kinetics was evaluated with silent polymerization and an important feature was discussed. The activation energy and other thermodynamic parameters were computed. Based on the obtained results an appropriate radical mechanism has been derived. TGA showed the polymer was stable up to 150 °C. The FT-IR and DSC analysis validates the atactic nature of the obtained polymer. The XRD pattern reveals the amorphous nature of polymer was dominated.     

Ultrasound assisted enzyme catalyzed synthesis of glycerol carbonate from glycerol and dimethyl carbonate

The present work illustrates the transesterification of glycerol to glycerol carbonate (GlyC) from dimethyl carbonate (DMC) using commercial immobilized lipase (Novozym 435) under ultrasonic irradiation. The experiments were performed in a batch reactor placed in an ultrasonic water bath using a sequence of experimental protocol to evaluate the effects of temperature, molar ratios of substrates, enzyme loading, duty cycle and ultrasound power on the conversion of glycerol to GlyC. It has been found that ultrasound-assisted lipase-catalyzed transesterification of glycerol would be a potential alternative to conventional alkali-catalyzed method, as high conversion (99.75%) was obtained at mild operating conditions: molar ratio of DMC to glycerol 3:1, catalyst amount of 13% (w/w), lower power input (100 W), duty cycle 50% and temperature (60 °C) in a relatively short reaction time (4 h) using Novozym 435 as catalyst. Ultrasound reduces the reaction time up to 4 h as compared to conventional stirring method (14 h) catalyzed by Novozym 435. The repeated use of the catalyst under the optimum experimental condition resulted in decay in both enzyme activity and product conversion.     

Poly(ethyleneglycol methacrylate phosphate) and heterocycle based proton conducting composite materials

Novel anhydrous proton conducting polymer electrolytes based on poly(ethyleneglycol methacrylate phosphate) (PEGMAP) and heterocycle have been investigated. The materials were synthesized via conventional radical bulk polymerization of ethylene glycol methacrylate phosphate in the presence of proton solvents such as imidazole (Im) or benzimidazole (BnIm). The poly(EGMAP–Im_x) or poly(EGMAP–BnIm_x) composites were produced where x is the molar ratio of heterocycle to monomer in the feed. The polymer–heterocycle electrolytes were characterized by elemental analysis (EA), FT-IR spectroscopy, thermogravimetry analysis (TG), differential scanning calorimetry (DSC) and impedance spectroscopy. Maximum proton conductivity of 2 × 10^− 4 S/cm has been obtained for the anhydrous composite electrolytes at 160 °C.     

Removal of Brilliant Green from wastewater using conventional and ultrasonically prepared poly(acrylic acid) hydrogel loaded with kaolin clay: A comparative study

The present work deals with the removal of Brilliant Green dye from wastewater using a poly(acrylic acid) hydrogel composite (PAA-K hydrogel) prepared by incorporation of kaoline clay. The composite has been synthesized using ultrasound assisted polymerization process as well as the conventional process, with an objective of showing the better effectiveness of ultrasound assisted synthesis. It has been observed that the hydrogel prepared by ultrasound assisted polymerization process showed better results. The optimum conditions for the removal of dye are pH of 7, temperature of 35 °C, initial dye concentration of 30 mg/L and hydrogel loading of 1 g. The extent of removal of dye increased with an increase in the contact time and initial dye concentration. A pseudo-second-order kinetic model has been developed to explain the adsorption kinetics of dye on the PAA-K hydrogel. Thermodynamic and kinetic parameters indicate that the adsorption process is spontaneous in nature and the PAA-K hydrogel prepared by ultrasound process is a promising adsorbent compared to conventional process. The obtained adsorption data has also been fitted into commonly used adsorption isotherms and it has been found that Freundlich as well as Langmuir adsorption isotherm models fits well to the experimental results.     

Polymerization of ethyl methacrylate under the influence of ultrasound assisted a new multi-site phase-transfer catalyst system – A kinetic study

The kinetics of multi-site phase-transfer catalyzed free radical polymerisation of ethyl methacrylate (EMA) using potassium peroxy disulphate (PDS) as a water soluble initiator and newly synthesized 1,4-dihexadecylpyrazine-1,4-diium dibromide as multi-site phase-transfer catalyst (MPTC) has been investigated in ethyl acetate/water two phase system at constant temperature 55 ± 1 °C under nitrogen atmosphere and ultrasound irradiation conditions. The rate of polymerization increases with an increase in concentrations of EMA, PDS and MPTC. The order with respect to monomer, initiator and MPTC were found to be 1.03, 0.52 and 0.53, respectively. Based on the observed results a suitable mechanism has been proposed to account for the experimental observations and its significance was discussed.     

Effect of ultrasound and centrifugal force on carambola (Averrhoa carambola L.) slices during osmotic dehydration

Osmotic dehydration (OD) of carambola slices were carried out using glucose, sucrose, fructose and glycerol as osmotic agents with 70 °Bx solute concentration, 50 °C of temperature and for time of 180 min. Glycerol and sucrose were selected on the basis of their higher water loss, weight reduction and lowers solid gain. Further the optimization of OD of carambola slices (5 mm thick) were carried out under different process conditions of temperature (40–60 °C), concentration of sucrose and glycerol (50–70 °Bx), time (180 min) and fruit to solution ratio (1:10) against various responses viz. water loss, solid gain, texture, rehydration ratio and sensory score according to a composite design. The optimized value for temperature, concentration of sucrose and glycerol has been found to be 50 °C, 66 °Bx and 66 °Bx respectively. Under optimized conditions the effect of ultrasound for 10, 20, 30 min and centrifugal force (2800 rpm) for 15, 30, 45 and 60 min on OD of carambola slices were checked. The controlled samples showed 68.14% water loss and 13.05% solid gain in carambola slices. While, the sample having 30 min ultrasonic treatment showed 73.76% water loss and 9.79% solid gain; and the sample treated with centrifugal force for 60 min showed 75.65% water loss and 6.76% solid gain. The results showed that with increasing in treatment time the water loss, rehydration ratio were increased and solid gain, texture were decreased.     

Solid electrolyte membranes from semi-interpenetrating polymer networks of PEG-grafted polymethacrylates and poly(methyl methacrylate)

Solid polymer electrolyte membranes were prepared as semi-interpenetrating networks by photo-induced polymerization of mixtures of poly(ethylene glycol) (PEG) methacrylate macromonomers in the presence of poly(methyl methacrylate) (PMMA) and lithium bis(trifluoromethanesulfonyl)imide salt. The composition of the membranes was varied with respect to the PMMA content, the degree of cross-linking, and the salt concentration. Infrared analysis of the membranes indicated that the lithium ions were coordinated by the PEG side chains. Calorimetry results showed a single glass transition for the blend membranes. However, dynamic mechanical measurements, as well as a closer analysis of the calorimetry data, revealed that the blends were heterogeneous systems. The ionic conductivity of the membranes increased with the content of PEG-grafted polymethacrylate, and was found to exceed 10^− 5 S cm^− 1 at 30 °C for membranes containing more than 85 wt.% of this component in the polymer blend.     

Synthesis and application of molecularly imprinted nanoparticles combined ultrasonic assisted for highly selective solid phase extraction trace amount of celecoxib from human plasma samples using design expert (DXB) software

In this work molecular imprinted nanoparticles (MINPs) was synthesized and applied for ultrasonic assisted solid phase extraction of celecoxib (CEL) from human plasma sample following its combination by HPLC–UV. The MINPs were prepared in a non-covalent approach using methacrylic acid as monomer, CEL as template, ethylene glycol dimethacrylate as cross-linker, and 2,2-azobisisobutyronitrile (AIBN) as the initiator of polymerization. pH, volume of rinsing and eluent solvent and amount of sorbent influence on response were investigated using factorial experimental design, while optimum point was achieved and set as 250 mg sorbent, pH 7.0, 1.5 mL washing solvent and 2 mL eluent by analysis of results according to design expert (DX) software. At above specified conditions, CEL in human plasma with complicated matrices with acceptable high recoveries (96%) and RSD% lower than 10% was quantified and estimated.The proposed MISPE-HPLC–UV method has linear responses among peak area and concentrations of CEL in the range of 0.2–2000 μg L⁻¹, with regression coefficient of 0.98. The limit of detection (LOD) and quantification (LOQ) based on three and ten times of the noise of HPLC peaks correspond to blank solution were 0.08 and 0.18 μg L⁻¹, respectively.     

Proton-conducting properties of the membranes based on poly(vinyl phosphonic acid) grafted poly(glycidyl methacrylate)

Proton-conducting properties of the graft copolymer electrolytes were examined throughout this work. The homopolymers poly(glycidyl methacrylate), PGMA and poly(vinyl phosphonic acid), PVPA were synthesized by free-radical polymerizations of the monomers glycidyl methacrylate, GMA, and vinyl phosphonic acid, VPA, respectively. The graft copolymers were produced by grafting of PVPA onto PGMA via ring opening of ethylene oxide groups. To examine the influence of the concentration of VPA on the proton conductivity, several graft copolymers were produced at various stoichiometric ratios with respect to monomer repeat units. The materials were characterized by FT-IR and ¹H NMR spectroscopy and the thermal properties were studied by thermogravimetry (TG) and differential scanning calorimetry (DSC). The TGA results demonstrated that the samples are thermally stable up to at least 150 °C. The proton conductivities of humidified and dry samples were studied via impedance spectroscopy. In the anhydrous state, the proton conductivity of P(GMA)-graft-P(VPA)₁₀ was 5 × 10^? 5 S/cm at 150 °C. The proton conductivity of the same material increased with the humidity content and reached to 0.03 S/cm at 80 °C under 50% of RH, which approached to that of Nafion^® at the same humidification level.     

Effects of ultrasound and temperature on copper electro reduction in Deep Eutectic Solvents (DES)

This paper concerns a preliminary study for a new copper recovery process from ionic solvent. The aim of this work is to study the reduction of copper in Deep Eutectic Solvent (choline chloride–ethylene glycol) and to compare the influence of temperature and the ultrasound effects on kinetic parameters. Solutions were prepared by dissolution of chloride copper salt CuCl₂ (to obtain Copper in oxidation degree II) or CuCl (to obtain Copper in oxidation degree I) and by leaching metallic copper directly in DES. The spectrophotometry UV–visible analysis of the leached solution showed that the copper soluble form obtained is at oxidation degree I (Copper I). Both cyclic voltammetry and linear voltammetry were performed in the three solutions at three temperatures (25, 50 and 80 °C) and under ultrasonic conditions (F = 20 kHz, PT = 5.8 W) to calculate the mass transfer diffusion coefficient kD and the standard rate coefficient k°. These parameters are used to determine that copper reduction is carried out via a mixed kinetic-diffusion control process. Temperature and ultrasound have the same effect on mass transfer for reduction of Cu^II/Cu^I. On the other hand, temperature is more beneficial than ultrasound for mass transfer of Cu^I/Cu. Standard rate constant improvement due to temperature increase is of the same order as that obtained with ultrasound. But, by combining higher temperature and ultrasound (F = 20 kHz, PT = 5.6 W at 50 °C), reduction limiting current is increased by a factor of 10 compared to initial conditions (T = 25 °C, silent), because ultrasonic stirring is more efficient in lower viscosity fluid. These values can be considered as key-parameters in the design of copper recovery in global processes using ultrasound.     

Ultrasound assisted polymerization of N-vinyl imidazole under phase-transfer catalysis condition – A kinetic study

The kinetics of phase-transfer catalyzed radical polymerization of N-vinyl imidazole (NVI) using potassium peroxy disulfate (PDS) as water soluble initiator and tetraoctylammonium chloride (TOAC) as PTC has been investigated in ethyl acetate/water two phase system assisted by ultrasound irradiation at constant temperature 60 + 1 °C under nitrogen atmosphere. and. The rate of polymerization increases with an increase in concentrations of NVI, PTC and PDS. The order with respect to [NVI], [PTC], and [PDS] were found to be 1.01, 1.03 and 0.52 respectively. Based on the observed results a suitable mechanism has been proposed to account for the experimental observations followed by a discussion on its significance.     

Optimization of ultrasound-assisted extraction of total monomeric anthocyanin (TMA) and total phenolic content (TPC) from eggplant (Solanum melongena L.) peel

The present study describes the extraction of total monomeric anthocyanin (TMA) and total phenolic content (TPC) from eggplant peel using ultrasonic treatments and methanol and 2-propanol as extraction solvents. The extraction yields were optimized by varying the solvent concentration, ultrasonic frequency, temperature and time of ultrasonic treatment. Box–Behnken design was used to investigate the effect of process variables on the ultrasound-assisted extraction. The results showed that for TPC extraction the optimal condition were obtained with a methanol concentration of 76.6%, 33.88 kHz ultrasonic frequency, a temperature of 69.4 °C and 57.5 min extraction time. For TMA the optimal condition were the following: 54.4% methanol concentration, 37 kHz, 55.1 °C and process time of 44.85 min.     

Effect of amphiphilic hyperbranched-star polymer on the structure and properties of PVDF based porous polymer electrolytes

An amphiphilic hyperbranched-star polymer (HPE-g-MPEG) was synthesized by grafting methoxy poly(ethylene glycol) to the end of the hyperbranched polyester (HPE) molecule using terephthaloyl chloride (TPC) as the coupling agent. The synthesized amphiphilic hyperbranched-star polymer was blended with poly(vinylidene fluoride) (PVDF) to fabricate porous membranes via typical phase inversion process, and then the membranes were filled and swollen by a liquid electrolyte solution to form polymer electrolytes. The influences of HPE-g-MPEG on the morphology, crystallinity, liquid electrolyte uptake, mechanical properties of the porous membranes and the electrochemical properties of the activated membranes were investigated. It was found that the addition of HPE-g-MPEG resulted in a significant increase in porosity and a considerable reduction in crystallinity of the blend membranes, which favored the liquid electrolyte uptake and, consequently, led to a remarkable increase in ion conductivity at ambient temperature. The maximum ion conductivity observed in this study was 1.76 × 10^? 3 S/cm at 20 °C for the blend membrane with a HPE-g-MPEG/PVDF ratio of 3/10 (w/w).     

Fabrication of bacterial cellulose thin films self-assembled from sonochemically prepared nanofibrils and its characterization

Bacterial cellulose (BC) film formation could be a critical issue in nanotechnology applications such as biomedical or smart materials products. In this research, purified pretreated BC was subjected to high intensity ultrasound (HIUS) and was investigated for the development of BC films. The morphological, structural and thermal properties of the obtained films were studied by using FE-SEM, AFM, FT-IR, XRD, TGA and DSC characterizations. Results showed that the most favorable purification treatment was the 0.01 M NaOH at 70 °C for 2 h under continuous stirring. The most suitable ultrasound operating conditions were found to be, 1 cm distance of ultrasonic probe from the bottom of the beaker, submerged in cold water bath cooling around 12 ± 2 °C. The power (25 W/cm²), time (30 min), BC concentration (0.1% w/w), amplitude (20 μm) and frequency (20 kHz) were maintained constant.     

Effect of melt-processing and ultrasonic treatment on physical properties of high-amylose maize starch

High-amylose maize starch (Hylon VII) was submitted to melt-processing in an internal mixer at 100 °C and 40 rpm for 8 min. Glycerol was used as a plasticiser at different polymer/glycerol ratios. Torque and temperature curves were obtained. After glycerol extraction with ethyl alcohol, the samples were dispersed at 5 g/L, and treated by ultrasound radiation at the same conditions for 30 min. Samples were characterised by ¹H NMR spectrometry, viscosity measurements, and X-ray diffractometry. The results revealed that both glycerol and water had an important role on the crystallinity properties of the resulting products. Melt-processed and sonicated samples showed similar ¹H NMR spectra. Ultrasound treatment caused a significant reduction in intrinsic viscosity for the sample previously processed with the highest glycerol content, probably because of its higher solubility in water.     

Effect of ultrasound and high hydrostatic pressure (US/HHP) on the degradation of dextran catalyzed by dextranase

In our current research work, the effect of combination of ultrasonic irradiation and high hydrostatic pressure (US/HHP) on the enzymatic activity and enzymatic hydrolysis kinetic parameters of dextran catalytic by dextranase were investigated. Furthermore, the effects of US/HHP on the structure of dextranase were also discussed with the aid of fluorescence spectroscopy and circular dichroism (CD) spectroscopy. The maximum hydrolysis of dextran was observed under US (40 W at 25 kHz for 15 min) combined with HHP (400 MPa for 25 min), in which the hydrolysis of dextran increased by 163.79% compared with the routine thermal incubation at 50 °C. Results also showed that, V_max and K_M values, as well as, k_cat of dextranase under US/HHP treatment were higher than that under US, HHP and thermal incubation at 50 °C, indicated that, the substrate is converted into the product at an increased rate when compared with the incubation at 50 °C. Compared to the enzymatic reaction under US, HHP, and routine thermal incubation, dextranase enzymatic reaction under US/HHP treatment showed decreases in Ea, ΔG and ΔH, however small increase in ΔS value was observed. In addition, fluorescence and CD spectra reflected that US/HHP treatment had increased the number of tryptophan on dextranase surface with increased α-helix by 19.80% and reduced random coil by 6.94% upon US/HHP-treated dextranase protein compared to the control, which were helpful for the improvement of its activity. These results indicated that, the combination of US and HHP treatments could be an effective method for improving the hydrolysis of dextran in many industrial applications including sugar manufacturing processes.     

Study on ionic conductivity of polymer electrolyte plasticized with PEG–aluminate ester for rechargeable lithium ion battery

We have synthesized poly(ethylene glycol) (PEG)-aluminate ester as a plasticizer for solid polymer electrolytes. The thermal stability, ionic conductivity and electrochemical stability of the polymer electrolyte which consist of poly(ethylene oxide) (PEO)-based copolymer, PEG–aluminate ester and lithium bis-trifluoromethanesulfonimide (LiTFSI) were investigated. Addition of PEG–aluminate ester increased the ionic conductivity of the polymer electrolyte, showing greater than 10^− 4 S cm^− 1 at 30 °C. The polymer electrolyte containing PEG–aluminate ester retained thermal stability of the non-additive polymer electrolyte and exhibited electrochemical stability up to 4.5 V vs. Li⁺/Li at 30 °C.     

Polymer electrolytes based on copolymer of poly(ethylene glycol) dimethacrylate and imidazolium ionic liquid

Polymer electrolytes based on the copolymer of N-vinylimidazolium tetrafluoroborate (VyImBF₄) and poly(ethylene glycol) dimethacrylate (PEGDMA) have been prepared. Ethylene carbonate (EC) and LiClO₄ are added to form gel polymer electrolytes. The chemical structure of the samples and the interactions between the various constituents are studied by FT-IR. TGA results show that these polymer electrolytes have acceptable thermal stability, are stable up to 155 °C. Measurements of conductivity are carried out as a function of temperature, VyImBF₄ content in poly(VyImBF₄-co-PEGDMA), and the concentration of EC and LiClO₄. The conductivity increases with PEGDMA and EC content. The highest conductivity is obtained with a value of 2.90 × 10^? 6 S cm^? 1 at room temperature for VP1/EC(25 wt.%)–LiClO₄ system, corresponding to the LiClO₄ concentration of 0.70 mol kg^? 1 polymer.