Gd_3Al_5O_(12)∶Eu~(3+)柠檬酸盐硝酸盐燃烧法合成及其发光性能研究

采用柠檬酸盐硝酸盐燃烧法,在较低的温度(900℃)下成功地合成单一晶相Gd3Al5O12∶Eu3+发光粉体,紫外激发荧光光谱分析表明,粉体615 nm和593 nm荧光发射源于Eu3+的5D0-7F2和5D0-7F1跃迁.该方法中各工艺条件(如pH值、柠檬酸/金属离子比、煅烧温度)对Gd3Al5O12∶Eu3+发光性能均有影响,通过试验得出了获得最佳发光性能荧光粉体的工艺参数.     

Gd3Ga5O12∶Eu3+发光纳米晶的燃烧合成及性质

以尿素为燃烧剂,乙二醇为分散剂采用燃烧法制备了Gd3Ga5O12∶Eu3+纳米晶。利用X射线衍射、电镜和荧光光谱对前驱体和热处理后样品的结构、形貌和发光性能进行了表征。XRD结果表明:700℃热处理2 h即可获得立方结构Gd3Ga5O12∶Eu3+纳米晶。根据Scherrer公式估算经700℃和900℃热处理2 h获得的纳米晶的一次性粒径分别为28 nm和42 nm。发射光谱和激发光谱的结果表明:特征发射峰来自于5D0-7FJ跃迁,而来自于Eu3+的5D0→7F1的磁偶极跃迁发射最强;宽激发带主要来自于Eu-O电荷迁移带和Gd3Ga5O12基质吸收。发射强度和激发强度随热处理温度的提高而增强。     

(ZnBaLa)BO3∶Eu3+的合成与发光的研究

高温固相扩散法合成了发光材料Zn1．5xBa1．5yLa1-x-y-z)BO3∶Eu3+z(x+y+z＜0．4)．对样品进行了XRD和IR分析,结果表明：在空气中900 ℃条件下,合成了荧光体样品,LaBO3中La3+离子被部分Zn2+和Ba2+离子取代使晶系发生了变化,LaBO3属于正交晶系,而(Zn0．27Ba0．24La0．61)BO3∶Eu3+0．05经过XRD属于立方晶系,a=0.639 7,V=0.261 8 nm3．扫描电镜测其晶貌,平均粒度为22 μm左右．样品的激发光谱和发射光谱显示：在基质BO3结构中O2—Eu3+的CT带位于295 nm,Eu3+的强发射来自5D0→7F1和5D0→7F2跃迁,存在磁偶极和电偶极两种跃迁．     

GdF_3∶Eu~(3+)/NaGdF_4∶Eu~(3+)纳米晶的水热合成及发光性质

采用水热法,以聚乙二醇(400)为分散剂,以NaOH和HNO3溶液调节初始溶液pH值,合成GdF3∶Eu3+和NaGdF4∶Eu3+纳米晶。XRD和SEM结果表明:在酸性溶液(pH=3,5)、中性溶液(pH=7)和碱性溶液(pH=9)中,分别获得具有正交结构的GdF3∶Eu3+纳米晶,GdF3∶Eu3+和NaGdF4∶Eu3+混合晶,六方结构NaGdF4∶Eu3+棒状微米晶。根据Scherrer公式估算pH=3和pH=5时制备纳米晶的一次性粒径分别为49和28 nm。样品的发射光谱结果表明:特征发射峰来自于5D2、5D1、5D0到7FJ跃迁。在主晶相为GdF3样品中,主发射峰来自于Eu3+的5D0→7F1的磁偶极跃迁;晶相为NaGdF4样品的主发射峰来自于Eu3+的5D0→7F2电偶极跃迁。5D0→7F1和5D0→7F2跃迁发射相对强度比值显示:Eu3+在NaGdF4晶体中的格位对称性下降。激发光谱显示出Gd3+和Eu3+具有较好的能量传递。     

GdF3∶Eu3+/NaGdF4∶Eu3+纳米晶的水热合成及发光性质

采用水热法,以聚乙二醇(400)为分散剂,以NaOH和HNO3溶液调节初始溶液pH值,合成GdF3∶Eu3+和NaGdF4∶Eu3+纳米晶。XRD和SEM结果表明:在酸性溶液(pH=3,5)、中性溶液(pH=7)和碱性溶液(pH=9)中,分别获得具有正交结构的GdF3∶Eu3+纳米晶,GdF3∶Eu3+和NaGdF4∶Eu3+混合晶,六方结构NaGdF4∶Eu3+棒状微米晶。根据Scherrer公式估算pH=3和pH=5时制备纳米晶的一次性粒径分别为49和28 nm。样品的发射光谱结果表明:特征发射峰来自于5D2、5D1、5D0到7FJ跃迁。在主晶相为GdF3样品中,主发射峰来自于Eu3+的5D0→7F1的磁偶极跃迁;晶相为NaGdF4样品的主发射峰来自于Eu3+的5D0→7F2电偶极跃迁。5D0→7F1和5D0→7F2跃迁发射相对强度比值显示:Eu3+在NaGdF4晶体中的格位对称性下降。激发光谱显示出Gd3+和Eu3+具有较好的能量传递。     

空气中合成M_2B_4O_7∶Eu~(3+)(M=Na,K)荧光体及其性质表征

以 M2 B4 O7( M=Na,K)为基质 ,在空气中掺杂稀土元素 Eu3+ 得到了 Na2 B4 O7∶ Eu3+ 和 K2 B4 O7∶ Eu3+荧光体 .探讨了体系的烧结条件和荧光性质 ,分析了晶体的结构 .结果表明 ,虽然两种体系的最佳合成条件不同 ,但是体系中都同时存在 [BO4 ]和 [BO3]结构 ;稀土离子 Eu3+ 的发光以电偶极跃迁5D0 -7F2 为主 ,处于非中心对称的格位上 ,并且可以很好地存在于基质中 ,Na2 B4 O7∶Eu3+ 具有较强的发光强度     

SrZnO_2∶Eu~(3+),Li~+长波紫外激发红光荧光体的合成及发光性能研究

采用高温固相法合成了一种长波紫外激发的SrZnO2∶Eu3+,Li+发光材料,用X射线衍射谱、荧光光谱对样品进行了表征。结果表明,Eu3+离子在SrZnO2基质中主要占据Sr2+离子不对称性格位,发射来源于5D0→7F2612 nm为主的红光。加入电荷补偿剂Li+离子能显著提高发光强度,350~400 nm内的激发峰也有明显提高,同时观察到来自Eu3+离子高能级5D1→7FJ(J=0~2)的跃迁发射,并对其产生机制进行了初步探讨。实验结果表明,SrZnO2∶Eu3+,Li+是一种有发展前途的长波紫外激发红光荧光体。     

（ZnBaLa）BO3：Eu^3＋的合成与发光的研究

高温固相扩散法合成了发光材料Zn1．5xBa1．5yLa1-x-y-z)BO3∶Eu3+z(x+y+z＜0．4)．对样品进行了XRD和IR分析,结果表明：在空气中900 ℃条件下,合成了荧光体样品,LaBO3中La3+离子被部分Zn2+和Ba2+离子取代使晶系发生了变化,LaBO3属于正交晶系,而(Zn0．27Ba0．24La0．61)BO3∶Eu3+0．05经过XRD属于立方晶系,a=0.639 7,V=0.261 8 nm3．扫描电镜测其晶貌,平均粒度为22 μm左右．样品的激发光谱和发射光谱显示：在基质BO3结构中O2—Eu3+的CT带位于295 nm,Eu3+的强发射来自5D0→7F1和5D0→7F2跃迁,存在磁偶极和电偶极两种跃迁．     

Eu3+掺杂ZMCB和ZMLB基光致发光玻璃纤维性能的研究

在发光粉废料处理中发现用高温固相反应和玻璃流股牵引方法,人工拉制了Eu3 掺杂ZnO-MgO-CdO-B2O3基质的光致发光玻璃纤维,直径为0.01～0.30 mm,长10余米.Eu3 离子613 nm的强发射归属于5D0-7F2电偶极跃迁,相对613 nm发射强度40%的591 nm发射归属于5D0-7F1磁偶极跃迁.说明Eu3 在局域环境中主要占据非对称中心格位.对不同浓度Eu3 的光衰曲线进行拟合,发现随着掺杂Eu3 浓度的增加,发光由单指数衰减变为双指数衰减.用SEM观察到玻璃纤维的表面光滑、低析晶、断口质密度高、断口贝纹呈明显沟状.并测试了发光玻璃纤维的一系列力学参数,也研究了Eu3 掺杂ZnO-MgO-La2O3-B2O3基玻璃纤维的光谱性能.     

LaAlO3∶0.05Eu3+微晶的水热合成与表征

通过水热反应合成了六角形LaAlO3∶0.05Eu3+微晶样品,采用X射线粉末衍射(XRD)、扫描电子显微镜(SEM)、能量色散X射线(EDX)和荧光光谱(PL)对产物进行表征,讨论了反应温度和NaOH浓度对LaAlO3合成的影响.XRD分析表明,所合成的样品属三方晶系(空间群R3c),对LaAlO3∶0.05Eu3+样品的X射线粉末衍射数据进行Rietveld精修,最终R因子为Rp=6.79%,Rwp=8.96%;其晶胞参数为a=b=0.53636(2)nm,c=1.3101(1)nm.SEM分析表明,LaAlO3∶0.05Eu3+微晶具有六角形形貌,颗粒较均匀,平均尺寸约为4!m.PL分析表明,LaAlO3∶0.05Eu3+微晶的特征发射为Eu3+的5D0→7F1跃迁发射.     

Synthesis, characterization and photoluminescence properties of CaSiO3:Eu3+ red phosphor

CaSiO3:Eu3+ (1-5 mol%) red emitting phosphors have been synthesized by a low-temperature solution combustion method. The phosphors have been well characterized by powder X-ray diffraction (PXRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and optical spectroscopy. PXRD patterns reveal monoclinic CaSiO3 phase can be obtained at 900°C. The SEM micrographs show the crystallites with irregular shape, mostly angular. Upon 254 nm excitation, the phosphor show characteristic fluorescence 5D0→7FJ (J=0, 1, 2, 3, 4) of the Eu3+ ions. The electronic transition located at 614 nm corresponding to 5D0→7F2 of Eu3+ ions, which is stronger than the magnetic dipole transition located at 593 nm corresponding to 5D0→7F1 of Eu3+ ions. Different pathways involved in emission process have been studied. Concentration quenching has been observed for Eu3+ concentration>4 mol%. UV-visible absorption shows an intense band at 240 nm in undoped and 270 nm in Eu3+ doped CaSiO3 which is attributed to oxygen to silicon (O-Si) ligand-to-metal charge-transfer (LMCT) band in the SiO3(2-) group. The optical energy band gap is widened with increase of Eu3+ ion dopant.     

LED用Sr(1-1.5x)Mo0.8Si0.2O3.8:Eu3+x红色荧光粉的制备及其荧光性能

通过高温固相法合成了LED用红色荧光粉Sr(1-1.5x)Mo0.8Si0.2O3.8∶Eu3+x（x=0.1,0.2,0.3,0.4,0.5）。 通过XRD、激发光谱和发射光谱测试了材料的物相组成以及发光性能。 x=0.1样品的XRD谱与JCPDS 08-0482(SrMoO4)的标准卡片相同。 Eu3+代替晶格中Sr2+的位置成为发光中心。 随着Eu3+含量x的增加,593 nm处的5D0-7F1跃迁和614 nm处的5D0-7F2跃迁发射强度会相互转换：当x≤0.4时,以磁偶极5D0-7F1跃迁为主,发射橙色光;而当x=0.5时,以电偶极5D0-7F2跃迁发射为主,发射红光。 可能是过量掺杂的Eu3+离子,只能存在于晶格空位形成缺陷,无法占据SrMoO4中Sr2+的格位中,Eu3+在晶格中占据非对称中心的格位,导致电偶极跃迁变成允许跃迁,从而增加了5D0-7F2跃迁,减弱了5D0-7F1跃迁。 因此,可以通过调节激活剂的含量获得不同发光色的荧光粉。 Eu3+掺杂的硅钼酸锶体系,614 nm激发下,在368 nm处出现宽的基质吸收峰和467 nm处7F0-5D2的跃迁峰,且这2处的吸收峰在x=0.5时比x=0.4时强3倍左右。 材料能非常好的吸收368 nm波长的光,产生颜色可调的橙红色。 与近紫外光LED芯片匹配良好。     

绿色荧光粉KNaCa2（PO4）2:Tb3+的制备及发光性能研究

采用高温固相法成功制备了KNaCa2(PO4)2:Tb3+绿色荧光粉,并研究了其发光性质。测量了其激发和发射光谱,样品发射峰位于418,440,492,545,586,622 nm,分别对应Tb3+的5 D3→7 F5,5 D3→7 F4,5 D4→7 F6,5 D4→7 F5,5 D4→7 F4,5 D4→7 F3能级跃迁,主发射峰位于545 nm。主激发峰位于350～390 nm之间,属于4f→4f电子跃迁吸收,与InGaN管芯匹配。确定了在KNaCa2(PO4)2基质中Tb3+浓度对其发光强度的影响及其自身浓度猝灭机制。研究了不同电荷补偿剂对KNaCa2(PO4)2:Tb3+材料发光的影响,其中Li+离子改善其发光强度最为明显。     

铕与2，4-二氯苯甲酸一维链状配位聚合物的合成，晶体结构和发光性质

溶液法合成了一个新的铕配位聚合物[Eu(2,4-DClBA)₃(CH₃CH₂OH)₂]_n(2,4-DClBA=2,4-二氯苯甲酸根),并用X-射线单晶衍射分析确定了其晶体结构。配合物晶体属于三斜晶系,P1空间群。标题配合物是无限一维链状聚合物,中心Eu³⁺离子通过桥联双齿2,4-二氯苯甲酸根氧原子连接。Eu³⁺离子的配位数为8     

Hydrothermal synthesis and fluorescence of YF3: Eu3+

<正>Europium(Ⅲ)-doped YF_3 is prepared by a hydrothermal process at 200℃.X-ray diffraction(XRD) pattern identifies the formation of YF_3 phase without detectable impurity.Environment scanning electron microscopy(ESEM) image shows the even size distribution of the samples with cubic morphology.The excitation and emission spectra of the rare earth ions doped YF_3 are investigated by fluorescence spectrophotometer.The excitation spectrum for 591 nm emission has several excitation bands at 320, 365,386,397 and 467 nm,and the main peak value was 397 nm.Typical Eu~(3+) emission peaks at 591 nm(~5D_0→~7F_1) and 612 nm (~5D_0→~7F_2) are observed when excited by 397 nm,and the strongest emission is 591 nm,demonstrating that the rare earth ions occupy the centrosymmetrical sites in YF_3.     

Effect of particle size and dopant concentration on photophysical properties of Eu3+-doped rare earth oxysulphide phosphor coatings

Europium-doped rare-earth oxysulphides (red phosphors) are often used as reference luminophore in pyrene-based pressure sensor coatings for aerodynamic applications. Different red phosphor samples were characterized for their particle size, chemical composition, photoluminescent properties and temperature sensitivity. The red phosphor samples were characterized using energy-dispersive X-ray spectroscopy (EDX) for elemental analysis and scanning electron microscopy (SEM) for morphology and particle size measurement. The particle size was in the range of 1.5-5.7 μm with morphology of hexagonal or spherical shape. It was found that phosphor with higher europium content exhibited higher luminescent emission intensity. The phosphor coatings were prepared by spraying a dispersion of the material in silicone resin. Smooth coatings were obtained by using phosphor samples with smaller particle size. Upon 334 nm excitation, the coatings showed characteristic luminescence 5D0→7FJ (J=0, 1, 2, 3, 4) of the Eu3+ ions. The electronic transition located at 626 nm (5D0→7F2) of Eu3+ ions was stronger than the magnetic dipole transition located at 595 nm (5D0→7F1). Luminescence decay curves obeyed double exponential behaviour. The phosphor samples showed temperature sensitivity of -0.012 to -0.168%/°C in the temperature range of 25-50 °C.     

橙红色荧光粉BaZnP2O7∶Eu3+的制备与发光特性

采用高温固相法合成了BaZnP2O7∶Eu3+荧光粉, 并对其发光性质进行了研究.     

Fluorescence properties of Eu3+ ions doped borate and fluoroborate glasses containing lithium, zinc and lead

The influence of glass composition on the fluorescence properties of Eu3+ ions doped borate and fluoroborate glasses modified with Li+, Zn2+ and Pb2+ cations have been investigated. The magnitude of splittings of 7F1 levels are analyzed using crystal-field (CF) analysis. The relative intensities of 5D0 --> 7F2 to 5D0 --> 7F1 transitions, crystal-field strength parameters and decay times of the 5D0 level have been determined and are found to be lower for Pb based glasses than those of Zn/Li based glasses. The lifetimes of 5D0 level are found to increase when borate glasses are modified with pure fluorides than with oxides and oxyfluorides. The fluorescence decay of 5D0 level fits perfect single exponential in the Eu3+:glass systems studied which indicates the absence of energy transfer between Eu3+ ions in these glasses.     

The effects of Gd3+ substitution on the crystal structure, site symmetry, and photoluminescence of Y/Eu layered rare-earth hydroxide (LRH) nanoplates

Well crystallized nanoplates of the (Y(0.95-x)Gd(x)Eu(0.05))(2)(OH)(5)NO(3)·nH(2)O ternary layered rare-earth hydroxides (LRHs), synthesized hydrothermally, have been investigated with emphasis on the effects of Gd(3+) substitution for Y(3+) on the structural features and optical properties. Characterizations of the materials were achieved by the combined techniques of XRD, FT-IR, TEM, DTA/TG, and optical spectroscopies. The results showed that Gd(3+) substitution leads to linearly expanded ab plane, shortened interlayer distance (c/2), and reduced hydration (smaller n value) of the crystal structure. As a consequence, the Ln(3+) partially shifts from the C(4v) to C(1) site symmetries and thus leads to systematically altered photoluminescence behaviors. Under the (7)F(0)→(5)L(6) transition excitation of Eu(3+) at 394 nm, both the (5)D(0)→(7)F(2) to (5)D(0)→(7)F(4) and the 595 nm (5)D(0)→(7)F(1) to 590 nm (5)D(0)→(7)F(1) intensity ratios linearly increase towards a higher Gd(3+) content. The incorporated Gd(3+) cations selectively sensitize emission from the C(1)-site Eu(3+) and produce a new charge transfer (CT) excitation band at ～254 nm. With this, the desired 615-nm red emission is obtainable either under intra-4f(6) transition excitation of Eu(3+) or by exciting the CT band. The materials have similar fluorescence lifetimes of 0.85 ± 0.05 ms for the 615-nm emission, irrespective of the Gd(3+) content and excitation wavelength.