Studies of Bis-(Sodium-Sulfopropyl)-Disulfide and 3-Mercapto-1-Propanesulfonate on/into the Copper Electrodeposited Layer by Time-of-Flight Secondary-Ion Mass Spectrometry

Interactions of functional additives SPS (bis-(sodium-sulfopropyl)-disulfide), MPS (3-Mercapto-1-Propanesulfonate), and Cl accumulated and incorporated on/into a copper electrodeposited layer were studied using time-of-flight secondary-ion mass spectrometry (TOF-SIMS) in combination with cyclic voltammetry measurements (CV). It was shown that the Cl and MPS surface coverage is dependent on the applied overpotential and concentration of Cl, SPS, or MPS in the solution. Detailed discussion on the mechanism of yielding CH₂SO₃⁻, C₃H₅SO₃⁻, CuSC₃H₆SO₃⁻, and CuS⁻ fragments and their assignment to the gauche or trans conformation was proposed. The mechanism of the process of incorporation and re-adsorption of MPS on/into a copper surface under electrochemical conditions without and with chloride ions and its impact on electrochemical properties was proposed. Moreover, it was shown that the presence of chloride ions, the ratio gauche/trans of MPS molecules, as well as the ratio chloride/thiols demonstrate a high impact on the accelerating abilities. Comparative studies conducted under open circuit potential conditions on the nitinol and copper substrate allowed for the identification of specific reactions/interactions of MPS, or SPS and Cl ions on the nitinol and copper surface.     

Capillary electrophoretic speciation of Cu(II) and Co(III) in the electroless copper plating baths

Summary A capillary electrophoretic method for the determination of Cu(II) and Co(III) chelates with ethylenediamine in electroless copper plating baths has been developed. The influence of carrier electrolyte parameters such as nature of counter-ion and pH were studied and discussed. The optimised separations were carried out in a fused silica capillary (57 cm × 75 μm I.D.) filled with an ethylenediamine sulfate electrolyte (20 mol L⁻¹ ethylendiamine, pH7.0 with H₂SO₄; applied voltage, +25 kV) using direct UV detection at 214 nm. The detection limits for a signalto-noise ratio of 3 and 10s hydrodynamic injection were 5×10⁻⁶ mol L⁻¹ for Cu(II) and 1×10⁻⁶ mol L⁻¹ for Co(III). The relative standard deviations of the peak areas for Cu(II) and Co(III) were found to be 1.5% and 2.4%, respectively, with five consecutive injections of standard solution containing 5×10⁻⁵ mol L⁻¹ of each metal ion. Application of the method to the speciation of Cu(II) and Co(III) complexes in copper plating bath samples is also demonstrated.     

离子对高效液相色谱分离及光度检测法测定meso-四(4-甲基-3-磺酸苯基)卟啉-铜、锌络合物

报道了meso-四(4-甲基-3-磺酸苯基)卟啉[T(4-MP)PS4]作柱前衍生试剂生成铜、锌络合物,四乙基碘化胺(TEA·I)为离子对试剂.离子对高效液相色谱及光度检测快速分离测定铜、锌的方法.流动相为乙腈+水,内含乙酸-乙酸钠缓冲液和四乙基碘化胺.方法具有较高的灵敏度和选择性,并用于测定莲子和花生等食品中的痕量铜和锌.     

Synthesis,crystal structure,antioxidation and DNA-binding properties of a dinuclear copper(II) complex with bis(N-salicylidene)-3-oxapentane-1,5-diamine

A Schiff base bis(N-salicylidene)-3-oxapentane-1,5-diamine (H₂L) and its Cu(II) complex, [Cu₂(L)₂]?CHCl₃, have been synthesized and characterized by physicochemical and spectroscopic methods. Single-crystal X-ray analysis revealed that the complex is a centrosymmetric binuclear neutral entity, in which Cu(II) is a five-coordinate in a distorted trigonal bipyramidal geometry. The DNA-binding properties of the free ligand and the complex have been investigated by electronic absorption, fluorescence, and viscosity measurements. The results suggest that the H₂L and the complex to DNA via the intercalation mode and the binding affinity of the complex were higher than that of the H₂L. The intrinsic binding constants K_b of the ligand and the complex are 2.2 × 10⁴ and 2.7 × 10⁴ M^?1, respectively. Antioxidant assay in vitro shows the Cu(II) complex possesses significant antioxidant activities and better scavenging activity than the H₂L and other antioxidants.     

高效液相色谱法测定药品中的乙二醇二乙醚二胺四乙酸

建立了高效液相色谱分析方法用来测定药品中乙二醇二乙醚二胺四乙酸(EGTA)含量,通过检测EGTA与Cu²⁺的配合物EGTA-Cu来检测EGTA。采用Ultimate-AQ C18色谱柱(250 mm×4.6 mm, 5 μm),流动相为乙腈-四丁基氢氧化铵水溶液(质量分数约0.3%四丁基氢氧化铵水溶液,醋酸调pH 6.50)-醋酸钠溶液(35 mmol/L醋酸钠,醋酸调pH 6.50)(20:20:60, v/v/v),检测波长为245 nm,流速为1.50 mL/min,柱温为40 ℃,进样量为100 μL。结果表明,EGTA质量浓度在0.10~15.00 mg/L范围内线性关系良好(R=0.9998);以信噪比(S/N)为3及10确定检出限和定量限,分别为0.05 mg/L和0.17 mg/L;样品加标平均回收率为98.34%~99.03%, RSD为1.08%~3.33%(n=9)。该方法操作简便,具有分离度好、灵敏度高、重复性好、回收率高等特点,适合药品中EGTA含量的检测,为EGTA检测提供了一种有效的检测方法。     

快速柱前衍生HPLC法检测曲格列汀中(R)-3-氨基哌啶

以邻苯二甲醛(OPA)和3-巯基丙酸为衍生试剂,建立了柱前衍生高效液相色谱(HPLC)测定曲格列汀中(R)-3-氨基哌啶含量的分析方法.(R)-3-氨基哌啶与衍生剂在碱性(pH 10.5)条件下于室温反应30s,进行柱前衍生,并利用高效液相色谱-质谱对衍生产物进行定性分析.采用YMC-Triart C18色谱柱(150...     

离子色谱法分析衣康酸成品中的Cl~-,NO_3~-和SO_4~(2-)

采用离子色谱法分析衣康酸成品中的Cl-,NO-3和SO2-4。通过改变淋洗液碳酸盐的总浓度和CO2-3与HCO-3的比例,比较衣康酸与Cl-,NO-3,SO2-4在AS14阴离子交换柱上的保留行为。结果表明,衣康酸和SO2-4的保留行为相似,二价离子受影响程度较一价离子大;另外,选择AS11阴离子交换柱进行比较,两柱均适合衣康酸成品中痕量Cl-,NO-3,SO2-4的分析,但溶质的出峰顺序有所不同。在AS14分析柱上,Cl-,NO-3和SO2-4的检出限分别为20,40和50μg/L,在0 5～200mg/L内其浓度与峰面积均有良好的线性关系。     

8-Phenyl-(4-oxy-acetic acid N-hydroxysuccinimidyl ester)-4,4-difluoro-1,3,5,7-tetramethyl-4-bora-3a,4a-diaza-s-indacene as a new highly fluorescent-derivatizing reagent for aliphatic amines in disease-related samples with high-performance liquid chromatography

A novel fluorescent-activated ester, 8-phenyl-(4-oxy-acetic acid N-hydroxysuccinimidyl ester)-4,4-difluoro-1,3,5,7-tetramethyl-4-bora-3a,4a-diaza-s-indacene (TMPAB-OSu) has been designed and synthesized for amine labeling in HPLC. Being used 11 aliphatic amines as the models, the derivatization conditions were optimized. In 0.2 mol/l borate buffer (pH 8.8), amines reacted with TMPAB-OSu at 30 °C to form the derivatives in 10 min. The fluorescent quantum yield of TMPAB-OSu and its amine derivatives are high even compared with fluorescein. The separation of these amine derivatives was achieved with a C₈ column and gradient elution by using 0.1 mol/l sodium acetate buffer (pH 5.0) and methanol. With fluorescence detection at an emission wavelength of 509 nm and an excitation wavelength of 497 nm, the detection limits of aliphatic amines were 2–18 fmol, at a signal-to-noise ratio of 3:1. The proposed TMPAB-OSu-based HPLC method has been applied to the analysis of urine samples of health, hepatic and renal patients and lake water. Recoveries from different matrices are from 96 to 104%, depending on the sample investigated.     

藉聚2-丙烯胺缩-3-(4-甲酰基苯偶氮)-4,5-二羟基-2,7-萘二磺酸分光光度法测定生物体液、食品和饮品中的镁

聚2-丙烯胺缩3－（4-甲酰基苯偶氮）-4，5-二羟基-2，7-萘二磺酸（PA-FPNS）在pH11．5的磷酸盐介质中．与镁（Ⅱ）形成一蓝色络合物，其最大吸收位于604nm，表观摩尔吸光系数ε=5．7×104L·mol-1·cm-1，线性范围为0．01～0．35mg／L，至少稳定12h。考察了30多种共存离子的影响，在所测样品中它们不干扰，无需掩蔽或分离即可直接测得其中的镁。     

Synthesis, structure, electrochemical properties, cytotoxic effects and antioxidant activity of 5-amino-8-methyl-4H-benzopyran-4-one and its copper(II) complexes

The chromone derivative 5-amino-8-methyl-4H-benzopyran-4-one (ligand) (1) has been used to obtain a series of Cu(II) complexes 2-4 as potential anticancer compounds. The molecular structures of ligand 1 and its Cu(II) complex 3 have been determined by X-ray crystallography. The cytotoxicity of all obtained compounds has been evaluated on melanoma A375 cell line. The ability of compounds 1-4 to take part in redox reactions and their antioxidant activity have been studied.     

Synthesis and electrochemical study of 3- and 4-(2-pyridyl)-1,3-benzothiazole complexes with transition metals (CoII, NiII, and CuII). Molecular structure of bis{(4-(2-pyridyl)-1,3-benzothiazole)copper(ii)} tetraacetate

A series of the M(L)Cl₂ · nH₂O and {M(L)}₂(OAc)₄ complexes (M = Ni^II, Co^II, and Cu^II; L is 3- and 4-(2-pyridyl)-1,3-benzothiazole) were synthesized by the reaction of L with MX₂ · nH₂O (X = Cl, OAc) in ethanol. The molecular and crystal structures of the CuL₂(OAc)₄ binuclear complex (L is 4-(2-pyridyl)benzothiazole) were determined by X-ray diffraction analysis. The copper atoms have a distorted tetragonal bipyramidal environment and are coordinated to the nitrogen atom of the pyridine moiety of the ligand and to two oxygen atoms of the bridging acetate ligands. The Cu-Cu distance is 2.6129(9) Å. The electrochemical behavior of the synthesized ligands and complexes was studied using the cyclic voltammetry and rotating disk electrode techniques in DMF solutions (0.1 M Bu₄NClO₄). The primary reduction of all the complexes under study is directed to the metal.     

The role of the histidine residue in the coordination abilities of peptides with a multi-histidine sequence towards copper(II) ions

Cu²⁺ complexes with peptides containing three histidine residues have very specific metal binding abilities and can mimic the structures of various multi-histidine metal binding sites in proteins. The main goal of the work concerns the investigations of coordination abilities of the group of N-terminally protected Ac-His-Arg-His-Gly-His-Gly, Ac-His-Gly-His-Arg-His-Gly, Ac-Gly-His-His-Arg-His-Gly and Ac-His-His-Gly-His-Arg-Gly, and their unprotected analogs His-Arg-His-Gly-His-Gly, His-Gly-His-Arg-His-Gly, Gly-His-His-Arg-His-Gly and His-His-Gly-His-Arg-Gly towards Cu²⁺ ions. Detailed spectroscopic (UV/Vis, CD and EPR) and potentiometric studies have been made. The stoichiometry and binding mode for each ligand–Cu²⁺ system were determined.     

N-[Chloro(dimethylamino)methylene]-N-methylmethanaminium chloride (TMUCl Cl), the reagent of choice for the solid-phase synthesis of anilides

An effective solid-phase preparation of anilides from supported carboxylic acids is described by their activation as the corresponding acid chlorides with TMUCl Cl.