半导体激光器泵浦的Cr:LiSAF激光器

本文报道了用半导体激光器泵浦Cr:LiSAF激光器腔的设计以及输出特性,在用准连续波泵浦时,阈值平均功率为42mW,在泵浦平均功率为60mW时得到了3mW的激光输出.     

二极管泵浦被动调QNd∶YAG/KTP绿光激光器（英文）

报道了LD泵浦的Nd∶YAG/KTP/Cr∶YAG结构被动调Q绿光激光器.当注入泵浦功率为750mW时,获得了平均功率38mW,脉冲宽度14.7ns,重复频率20.4kHz,峰值功率126.6W的调Q绿激光输出.     

LD端面泵浦腔内倍频Yb∶YAG绿光激光器

报道了一种激光二极管（LD）端面泵浦10at％掺杂Yb∶YAG激光晶体（4×4×1 mm）和Ⅰ类临界相位匹配LBO的腔内倍频全固态绿光激光器.为了克服“绿光问题”,采用了两个激光二极管偏振耦合系统.在双路泵浦功率为1.2 W时,获得最高功率为40 mW 525 nm的连续基模激光输出.在腔内插入Cr4＋:YAG饱和吸收体被动调Q,在泵浦功率为1.2 W时,可以获得平均功率为5.2 mW,脉冲重复频率为2.44 kHz,脉冲宽度为51.5 ns,峰值功率为41.7 W的515 nm脉冲激光输出.输出波长发生变化,而且515 nm脉冲激光输出的阈值仅为728 mW.     

LD端面泵浦腔内倍频Yb:YAG绿光激光器

报道了一种激光二极管(LD)端面泵浦10at%掺杂Yb:YAG激光晶体(4×4×1mm)和Ⅰ类临界相位匹配LBO的腔内倍频全固态绿光激光器.为了克服"绿光问题",采用了两个激光二极管偏振耦合系统.在双路泵浦功率为1.2W时,获得最高功率为40mW525nm的连续基模激光输出.在腔内插入Cr4+:YAG饱和吸收体被动调Q,在泵浦功率为1.2W时,可以获得平均功率为5.2mW,脉冲重复频率为2.44kHz,脉冲宽度为51.5ns,峰值功率为41.7W的515nm脉冲激光输出.输出波长发生变化,而且515nm脉冲激光输出的阈值仅为728mW.     

皮秒激光泵浦的亚10fs钛宝石激光器

研制了高稳定Nd∶YVO_4皮秒激光振荡器,并在15 W、808nm激光泵浦下得到6 W的连续锁模皮秒激光输出,光-光效率为40%.对该皮秒激光进行单通放大后得到14 W的基频光输出,倍频后可以得到7 W的532nm皮秒激光,用作钛宝石振荡器的泵浦源.在4.5 W的皮秒532nm激光泵浦下,结合腔外压缩,得到了脉宽为9.4fs、平均功率为150mW的脉冲序列输出.调节钛宝石振荡器的腔长使其与皮秒振荡器的腔长一致时,可实现自触发克尔透镜锁模.实验结果表明皮秒激光泵浦可以有效地触发钛宝石激光器的自动锁模,输出飞秒脉冲序列.     

高效三倍频全固态Nd∶YAG/LBO紫外激光器

报道了一种侧面泵浦Nd∶YAG、声光调Q、LBO晶体腔外倍频和三倍频的355 nm准连续波紫外激光器.采用结构简单、紧凑的平-凹腔设计,在152 W的泵浦功率下,重复频率5 kHz时,获得平均功率1.62 W的355 nm TEM00模激光输出,三倍频的转换效率为25%;重复频率1 kHz时,获得平均功率518 mW、单脉冲能量518 μJ、脉宽17 ns、峰值功率高达30 kW的紫外激光输出.     

二极管泵浦被动调Q Nd:YAG/ KTP绿光激光器

报道了LD泵浦的Nd:YAG/KTP/Cr:YAG结构被动调Q绿光激光器.当注入泵浦功率为750mW时,获得了平均功率38mW,脉冲宽度14.7ns,重复频率20.4kHz,峰值功率126.6W的调Q绿激光输出.     

宽光谱全正色散锁模掺镱光纤激光器

介绍了一种全正色散宽光谱被动锁模掺镱光纤激光器,利用非线性偏振旋转技术实现全正色散掺镱光纤激光器的被动锁模.当泵浦功率输出为500mW时,激光脉冲输出功率大于139mW,重复频率约为28.1MHz,脉冲宽度为3.8ps.为了进一步研究全正色散光纤激光器的宽光谱输出特性,在腔内熔接50m单模光纤,同时去除双折射滤波片,在泵浦功率为500mW时,观察到稳定锁模单脉冲耗散孤子,光谱范围为1 005~1 140nm,输出激光脉冲最大平均功率为90mW,重复频率为3.58MHz,脉冲宽度为519ps.     

LD脉冲侧面泵浦Nd∶YAG电光调Q低重频窄脉宽紫外激光器

介绍了在1~20 Hz电光调Q情况下,半导体脉冲激光侧面泵浦Nd∶YAG晶体腔外四倍频266 nm紫外激光器的输出特性.实验采用直腔结构,在腔外分别利用KTP和BBO晶体产生532 nm倍频绿光、266 nm四倍频紫外激光.当泵浦电流为120 A、重复率为1 Hz时,266 nm紫外激光最大单脉冲能量为15.4 mJ、脉宽8 ns,峰值功率高达1.93 mW;重复率20 Hz时,获得了最大平均功率为156.2 mW的266 nm紫外激光输出,四倍频的转换效率为10.63％.同时利用一组分光镜,获得了352 mW的532 nm脉冲绿光和423 mW的1 064 nm脉冲红外光输出.     

单频纳秒脉冲全光纤激光器实现300 W平均功率输出

搭建了一台主振荡功率放大（MOPA）结构的单频脉冲全光纤激光器。通过对线宽为 20 kHz 的连续单频激光器进行强度调制,获得了重复频率 10 MHz、脉宽约 8 ns、平均功率约 0.5 mW 的单频脉冲种子激光。采用多级掺镱光纤放大器对脉冲种子激光进行级联放大,获得了平均功率 300.8 W 的高功率激光输出。目前,激光器输出功率仅受限于泵浦功率,有望通过增加泵浦功率进一步提高输出功率。     

紧凑型LD端面抽运Nd:YAG内腔三倍频准连续355 nm紫外激光器

报道了一台LD端面抽运Nd:YAG晶体内腔三倍频355 nm激光高效率、高峰值功率准连续输出的全固态紫外激光器.激光腔采用紧凑型平平直腔,腔长仅106 mm.当注入抽运功率为5.73 W、重复频率为9 kHz时,获得163 mW的355 nm激光准连续输出,光光转换效率达到最高2.84％.当注入抽运功率为6.7 W重复频率为5 kHz时,获得最高174 mW的355 nm激光准连续输出,输出功率短期不稳定性为5％,光束质量因子M²为3.79.当注入抽运功率为5.73 W、重复频率为2 kHz时,获得112 mW的355 nm激光准连续输出,峰值功率最高达到9.15 kW.通过采用内腔倍频技术和设计合理的腔结构,实现了中小功率准连续输出的全固态紫外激光器的小型化、便携化,进一步拓宽了紫外激光器的应用领域. 关键词： LD端面抽运 内腔三倍频 Q')" href="#">声光调Q 紫外激光     

自锁模Cr：LiSAF激光器的实验研究

以功率为９００ｍＷ，波长为４８８ｎｍ的单线氩离子激光作为泵浦源，在腔内不加任何主动调制器和可饱和吸收体的情况下实现了Ｃｒ：ＬｉＳＡＦ激光器的飞秒级自锁模运转，得到了脉冲宽度为４０ｆｓ，重复频率为１００ＭＨｚ，平均输出功率为４５ｍＷ的稳定的锁模脉冲序列。     

Acousto-optic Q-switched laser performances of Er3+:Yb3+:LuAl3（BO3）4 crystal at 1.5-1.6 μm

Diode-pumped acousto-optic Q-switched pulse laser at 1.5-1.6 μm is obtained in an Er3+:Yb3+:LuAl3 (BO3)4 crystal. Single-pulse laser operation with slope efficiency of 14% and threshold of approximately 100 mW is realized at an average absorbed pump power of 314 mW and repetition frequency of 20 kHz. Output pulse energy is 67 μJ. The effects of pulse repetition frequency, absorbed pump power, and duty cycle on the wavelength and pulse profile of the Q-switched Er3+:Yb3+:LuAl3(BO3)4 laser are also investigated.     

An efficient intracavity-pumped KTP optical parametric oscillator at 1572 nm

We demonstrate an efficient and eye-safe wavelength intracavity optical parametric oscillator (OPO),based on a KTP crystal inside a Q-switched Nd:YVO4 laser end pumped by a fiber-coupled diode laser. Inthe acousto-optic Q-switched operation with the pulse repetition rate of 10 kHz, a 1572-nm eye-safe laser with the average power of 237 mW at the incident pump power of 5.64 W is obtained. Under the pulse repetition rate of 5 kHz, the signal light with pulse width of 2 ns and peak power of 18.5 kW is achieved.The conversion efficiency of the average power is 4.2% from pump diode to OPO signal output and thesignal pulse duration is about 13 times shorter than that of the depleted pump light.     

连续锁模Nd：YVO4激光器实现1 GHz高频输出

LD抽运全固体Nd:YVO4激光器在连续锁模状态运转下获得了高达1 GHz的重复频率.实验中采用半导体可饱和吸收镜作为锁模元件.利用透过率只有0.8%的输出镜以及可获得较小抽运光斑的2 W LD作为抽运源来优化激光器设计,有效地抑制了调Q锁模状态的运转.低的激光器振荡阈值（35 mW）和连续锁模阈值(0.8 W)显示了饱和吸收体低的插入损耗和激光器合理的设计.在最大抽运1.6 W时获得了210 mW的平均输出功率.     

连续锁模Nd∶YVO4激光器实现1 GHz高频输出

LD抽运全固体Nd∶YVO4激光器在连续锁模状态运转下获得了高达1 GHz的重复频率.实验中采用半导体可饱和吸收镜作为锁模元件.利用透过率只有0.8%的输出镜以及可获得较小抽运光斑的2 WLD作为抽运源来优化激光器设计,有效地抑制了调Q锁模状态的运转.低的激光器振荡阈值(35 mW)和连续锁模阈值(0.8 W)显示了饱和吸收体低的插入损耗和激光器合理的设计.在最大抽运1.6 W 时获得了210 mW的平均输出功率.     

Efficient laser operation and continuous-wave diode pumping of Cr2+:ZnSe single crystals

Efficient continuous-wave laser operation of Cr²⁺:ZnSe was demonstrated with an output power of 1400 mW at an absorbed pump power of 1900 mW from a Tm:YAG laser. Under continuous-wave diode pumping at 1.54 μm an output power of 15 mW was obtained from a Cr⁺²:ZnSe laser. Excited state absorption is shown to be negligible in the pump and laser spectral region. Received: 12 October 2000 / Published online: 30 November 2000     

Highly efficient, low-cost femtosecond Cr3+ :LiCAF laser pumped by single-mode diodes

We describe efficient continuous-wave (cw) and cw mode-locked operations of a Cr3+ :LiCAF laser, pumped by inexpensive single spatial mode laser diodes. Up to 280 mW of cw output power was obtained with 570 mW of absorbed pump power, with a corresponding slope efficiency of 54%. Continuous tuning between 765 and 865 nm was demonstrated using a fused silica prism. A semiconductor saturable absorber mirror was used to initiate and sustain stable, self-starting, mode-locked operation. In cw mode locking, the laser produced 72 fs (FWHM) duration pulses, and 1.4 nJ pulse energy, at an average output power of 178 mW. Electrical to optical conversion efficiencies of 7.8% in mode-locked operation and 12.2% in cw operation were demonstrated.     

Diode-pumped -switched Nd:YVO(4) yellow laser with intracavity sum-frequency mixing

A compact high-power yellow pulsed laser has been demonstrated by use of intracavity sum-frequency mixing in a diode-end-pumped Q -switched Nd:YVO(4) dual-wavelength laser. A three-mirror configuration forming two separate laser cavities is used to optimize the gain match for simultaneous dual-wavelength emission in Q -switched operation. Under the optimum cavity-length condition, the highest yellow average power is 340 mW and the peak power is 2 kW, obtained at 12.5 W of pump power.     

Room-temperature continuous-wave operation of Ti:sapphire buried channel-waveguide lasers fabricated via proton implantation

Fabrication and laser operation of proton-implanted Ti:sapphire buried channel waveguides is reported for the first time to our knowledge. Without any postimplantation annealing of the structures, continuous laser operation near 780 nm was demonstrated at room temperature at an absorbed pump power threshold of 230 mW. Single-transverse-mode laser emission was observed with measured beam propagation factors M(2)(x) and M(2)(y) of 1.5 and 1.2, respectively. An output power of 12.4 mW for 1 W pump power was obtained with an output coupler of 4.6% transmission at the signal wavelength. Higher output powers were measured in waveguides with larger cross sections exhibiting multimode laser emission.