Porphyrin-doped solgel-lined structured optical fibers for local and remote sensing

We constructed a type of sensor by depositing a solgel layer within the interior holes of a silica-structured fiber and, subsequently, coating this with an acid-responsive porphyrin. Protonation of the porphyrin by an acidic gas (HCl in this case), is detected by a large change in the visible spectrum. Compared to previous work on a liquid-core sensor in a structured optical fiber, the signal-to-noise ratio of this gas sensor shows a reduced signal strength, but the detection rate is increased about fortyfold.     

Optical fiber humidity sensor based on evanescent-wave scattering

The phenomenon of evanescent-wave scattering (EWS) is used to design an optical-fiber humidity sensor. Porous solgel silica (PSGS) coated on the surface of a silica optical-fiber core scatters evanescent waves that penetrate the coating layer. Water molecules in the gas phase surrounding the optical fiber can be absorbed into the inner surface of the pores of the porous silica. The absorbed water molecules form a thin layer of liquid water on the inner surface of the porous silica and enhance the EWS. The amount of water absorbed into the PSGS coating is in dynamic equilibrium with the water-vapor pressure in the gas phase. Therefore the humidity in the air can be quantitatively determined with fiber-optic EWS caused by the PSGS coating. The humidity sensor reported here is fast in response, reversible, and has a wide dynamic range. The possible interference caused by EWS to an optical-fiber gas sensor with a reagent-doped PSGS coating as a transducer is also discussed.     

Ultralow-threshold Yb(3+):SiO(2) glass laser fabricated by the solgel process

A Yb-doped silica microcavity laser on a silicon chip is fabricated from a solgel thin film. The high-Q micro-toroid cavity, which has a finesse of 10,000, is evanescently coupled to an optical fiber taper. We report a threshold of 1.8 microW absorbed power that is, to the best of our knowledge, the lowest published threshold to date for any Yb-doped laser. The effect of Yb(3+) concentration on laser threshold is experimentally quantified.     

光纤SPR湿敏传感器及其共振光谱特性研究

提出并研制了基于光纤SPR传感探针的新型湿敏传感器。首先研究了光纤SPR传感探针对环境湿度变化的敏感特性,在此基础上提出在光纤SPR传感探针表面增覆不同厚度且具有水分子吸附功能的PVA薄膜来实现环境相对湿度的监测。研究结果表明,增覆双层PVA薄膜的光纤SPR传感探针在高湿区具有较好监测效果,其共振强度对应的相对湿度测量灵敏度达到1.59%/%RH,较光纤SPR探针呈现显著提高。而增覆单层PVA薄膜的光纤SPR传感探针在高湿区共振波长对应的相对湿度监测灵敏度达到2.411nm/%RH。此外所提出的新型光纤SPR湿敏探针在PVA薄膜失效后经过特殊工艺处理仍可重复镀膜使用。     

Non-contact detection of laser-generated surface acoustic waves using fiber optic Sagnac interferometer

A high powered Q-switched Nd:YAG laser was used to excite the surface waves, and an optical fiber sensor was used to detect the out-of-plane displacements due to the propagating waves. This sensor is based on the fiber optic Sagnac interferometer, which has the path-matched configuration and does not require active stabilization. Quadrature phase bias between two interfering laser beams in the Sagnac loop is applied by controlling the birefringence in an optical path using a fiber polarization controller. A stable quadrature phase bias can be confirmed by observing the interferometer output according to the change of phase bias. Additional signal processing is not needed for the detection of ultrasonic waves using the Sagnac interferometer. The performance of the fiber optic Sagnac interferometer was investigated, and laser-generated surface wave signals were detected using this fiber optic sensor. The developed fiber optic sensor configured in this study is very simple and is effective for non-contact detection of ultrasonic waves.     

Numerical simulation of wavelength-modulated surface plasmon resonance-based fiber optic sensor

A systematically theoretical analysis of a surface plasmon resonance (SPR)-based optical fiber sensor is carried out. A three-layer mode (fiber core/gold/sample) is used to simulate the SPR-based optical fiber sensor. Several parameters including the thickness of gold layer, numerical aperture (NA) of fiber, sensing region length and fiber core diameter have been investigated to evaluate the sensitivity and measurement accuracy of sensor. A detailed explanation for the effect of these parameters on the sensor is presented to give a guideline to optimally design the SPR-based optical fiber sensor.     

光纤光栅压力传感器的理论建模及实验研究

鉴于压力传感器为工业生产中压力监控的一种必不可少的设备,分析了光纤光栅中心波长与光纤光栅应变之间的关系,阐述了带有硬中心的圆形膜片受到均匀压之后,膜片中心的挠度与压力之间的数学关系。在此基础上设计了圆形膜片作为流体压力转化光纤光栅敏感物理量的元件,并结合辅助元件完成对光纤光栅传感器组装,建立了传感器输入输出之间的线性数学模型。通过实验验证传感器线性度和重复性,运用数学计算得出了光纤光栅压力传感器各项参数,灵敏度Km=-0.658 nm/MPa,初始波长0=1 578.441 nm,为后期传感器稳定性作好了铺垫。     

应用光学双稳原理的高精度光纤传感器

本文提出一种光纤干涉仪与光电混合光双稳装置相结合的新型光纤传感器.用光双稳开关脉冲计数度量温度变化,其测量精度比基于干涉条纹计数的一般干涉型光纤传感器的精度约高10～100倍,而且测量精度可调节.完成了这种传感器原理的模拟实验验证.     

Application of a WGM optical fiber probe fabricated by 3D printing technology for glucose concentration measurement

This study proposes a method for manufacturing a whispering gallery mode (WGM) optical fiber probe used for measuring glucose. The principle of the WGM optical fiber probe consists of the bending interference that occurs between the core mode and cladding mode. 3D printing technology was used to create a mold for the optical fiber sensor so that the bent optical fiber sensor was fixed within the mold to ensure a stable bend radius. This method of fabrication allows for easier installation and replacement of the resulting optical fiber compared to WGM optical fiber sensors fabricated by traditional methods. The results of the concentration test showed that as the glucose aqueous solution concentration increased from 0 to 10%, the wavelength was red shifted and the transmission loss gradually increased. At a bend radius of 3.1 mm and an etching diameter of 46 μm, the wavelength sensitivity was 1.475 nm/% and the R-squared value was 0.983, indicating an extremely high sensitivity. These results confirm that the WGM optical fiber probe created in this study can be used to measure glucose concentrations with high sensitivity, and that it is relatively easy to manufacture, install, and replace. Therefore, the proposed WGM optical fiber probe exhibits good performance and is suitable for use as a glucose concentration sensor.     

Low-Temperature Radiometric Measurements Using a Silver Halide Optical Fiber and Infrared Optical Devices

In this study, we measured an infrared radiation which is transferred by a silver halide optical fiber from a heat source using a radiometer system for low-temperature measurements. To increase the amount of infrared radiation through the silver halide optical fiber and to the pyroelectric sensor, infrared optical devices used were an infrared focusing lens and a collimator. The relationship between the temperatures of a heat source and the measured radiometer signals were determined. The measurable temperature range of a fiber-optic temperature sensor using a pyroelectric sensor was from 298 to 333 K. It is expected that a noncontact low-temperature sensor using an infrared optical fiber can be developed for medical and industrial usages based on the results of this study.     

基于表面等离子体共振原理的空芯光纤传感器

设计了一种基于表面等离子体共振原理,使用空芯光纤作为光波导、外表面镀金属膜的光学材料圆柱体作为探头的新型折射率传感器。通过建立光学模型进行分析,在理论上推导出了这种传感器的传输光谱损耗公式,并针对该传感器在不同的光纤长度、探头材料、检测物质折射率等参数设置下的检测性能进行了分析,获得了各种参数对其性能的影响。由于该传感器可针对不同折射率的检测物质灵活地更换合适探头材料,相对于传统的表面等离子体共振光纤传感器,在易用性和性价比等方面具有更好的应用价值。     

Intensity modulated silver coated glass optical fiber refractive index sensor

Miniature optical fiber sensors with thin films as sensitive elements could open new fields for optical fiber sensor applications. Thin films work as sensitive elements and a transducer to get response and feedback from environments, in which optical fibers act as a signal carrier. A novel Ag coated intensity modulated optical fiber sensor based on refractive index changes using IR and UV-Vis(UV-visible) light sources is proposed. The sensor with an IR light source has higher sensitivity compared to a UV-Vis source. When the refractive index is enhanced to 1.38, the normalized intensity of IR and UV-Vis light diminishes to 0.2 and 0.8, respectively.     

分布式光纤温度压力传感器设计

为了实现油田井下温度压力的全分布式测量,提出了一种基于光纤散射原理的分布式温度压力测量方法。该方法通过对普通光纤进行封装设计,制作成传感光纤。由于光纤传感器周围流体的温度和压力会对传感光纤内的散射光产生调制作用,通过光纤解调仪解调出光纤拉曼散射参数和布里渊散射频移就能够实现温度和压力的实时在线测量。实验结果表明:设计的分布式光纤温度压力传感器可以实现的温度测量分辨率为0.1 ℃,压力测量分辨率为0.07 MPa。基本满足油田井下温度压力测量的全分布式、实时在线、可靠性高、精度高、抗干扰能力强等要求。     

光纤激光器及其在传感中的应用

介绍了光纤激光器的基本结构和特点，着重介绍了光纤激光器在相位型、波长型、光强型和偏振态型传感器中的应用，指出了光纤激光器在传感中的发展趋势。     

A multi-parameter sensor system using concentric core optical fiber

We, for the first time, report an experimental demonstration of multi-parameter fiber sensor system using the concentric core optical fiber, which can simultaneously determine the stress, the position of stress and the cracks. A high bending-sensitive concentric core optical fiber has been used in a mesh type structure to form the multi-function sensor.     

高分辨率光纤应变传感技术的研究

介绍光纤应变传感器中光纤端面反射镜的制作方法,镀膜光纤的连接技术和构成不对称光纤法布里－珀罗干涉腔的方法。应用低反射率不对称光纤法布里－ 珀罗干涉腔与光纤连接构成的光纤应变传感器,以提高分辨率;重点导出此干涉腔反射光与应变的数学模型,论述其工作原理和测量方法,通过实验证明文中所述应变传感原理和测量方法是正确的,其分辨率优于０－００６８με。     

Fiber-optic pH sensor based on sol-gel film immobilized with neutral red

In this study, we developed a fiber-optic pH sensor based on a sol-gel film immobilized with neutral red (NR). A solgel film was prepared by mixing tetramethylorthosilicate (TMOS), trimethoxymethylsilane (MTMS), ethanol (EtOH), distilled water (H₂O), and NR powder. Accordingly, the thin pH sol-gel film was fabricated through a sol-gel process with a dip-coating method. The thickness and diameter of the fabricated pH sol-gel film are 0.11 and 0.6 mm, respectively. We measured the optical absorbance and the light intensity with the spectra of reflected light, which change with the color variation of the pH sol-gel film in the fiber-optic sensing probe. From the experimental results, we demonstrated that the proposed fiber-optic pH sensor has good reversibility, reproducibility, and a fast response time, in which the optical properties of the NR-based pH sol-gel film change with the pH value.     

An all-fiber high resolution fiber grating concentration sensor

An all-fiber high resolution optical fiber grating concentration sensor has been studied theoretically and experimentally. A long period grating is used as the sensor head and a wavelength matched fiber Bragg grating is used as an interrogator to convert wavelength into intensity encoded information for interrogation. A concentration resolution of 0.104 g/L for NaCl solution is realized in experiment. The all-fiber sensor system, with the sensor head and the interrogator being all optical fiber components, is suitable for far-distance monitoring. The sensor system is with multifunction and can be used for temperature monitoring. A temperature resolution of 0.013 °C has realized in experiment.     

埋入式F-P光纤应变传感器在混凝土桥梁健康监测中的应用研究

对基于白光干涉的埋入式F_P光纤应变传感器的测试原理及主要结构参数进行了分析,介绍了该埋入式传感器的研制工艺特点。通过对传感器的性能考核试验,验证了该传感器具有优良的精度稳定性和耐久性,通过秦沈客运专线辽河特大桥施工过程监测试验,验证了该传感器满足桥梁施工现场复杂状况下混凝土结构应变监测的要求。由于该传感器的成本不及同类型进口产品的1/5,具有广阔的普及应用前景。     

基于光纤气泡和纤芯失配的Mach-Zehnder干涉液体折射率传感器

介绍了一种基于光纤气泡和纤芯失配的Mach-Zehnder干涉液体折射率传感器. 将两根纤芯经过腐蚀的普通单模光纤熔接在一起, 在熔接点处形成一个气泡, 在距气泡20 mm处级联一段20 mm的细芯光纤, 再接入一段单模光纤, 形成单模光纤-气泡-单模光纤-细芯光纤-单模光纤结构的传感器. 气泡与光纤芯径失配处的两个节点起到光纤耦合器的作用, 从而形成光纤Mach-Zehnder干涉仪. 环境液体折射率的变化,将使得传感器透射谱能量发生变化, 通过测量干涉谱波峰峰值能量从而实现对折射率的测量. 并对所制作传感器的折射率响应特性进行了实验研究, 实验结果表明干涉谱波峰峰值能量与环境液体折射率之间存在良好的线性关系, 当环境液体折射率变化范围在1.351–1.402时, 响应灵敏度为143.537 dB/RIU, 线性度0.996. 该传感器在生物化学领域有较好的应用前景. 关键词： 光纤气泡 纤芯失配 Mach-Zehnder干涉仪 折射率传感