Buffer medium exchange in continuous cell and particle streams using ultrasonic standing wave focusing

A microfluidic strategy to perform buffer exchange of particle and cell suspensions in a continuous flow format on, chip is presented. Ultrasonic standing wave technology is utilized to confine particulate matter to the centre of a buffer exchange channel while particle free buffer is sequentially aspirated via capillaries that branch off from the buffer exchange channel. At each such branch, clean buffer is supplied at an equal flow-rate from a capillary at the opposing channel wall, generating a sideways translation of the original buffer, laminated with a wash buffer stream. Each such junction increases the buffer exchange ratio accordingly. The reported buffer exchange system provides means to adjust buffer exchange conditions on-line by tuning the ratio of the cross-flow wash buffer relative the sample suspension flow, rate. The system performance was evaluated using 5 μm polystyrene microbeads and a dye as the model contaminant. Wash efficiencies up to 96.4% were accomplished with a 0.2% solid content bead suspension, using eight cross-flow junctions, effectively exchanging the carrier buffer twice. The corresponding data for erythrocyte washing was recorded to be 98.3% at a haematocrit of 2%.     

Buffer system for the separation of neutral and charged small molecules using micellar electrokinetic chromatography with mass spectrometric detection

An organic buffer system will be discussed that is suitable for the separation of neutral as well as charged molecules be means of micellar electrokinetic chromatography (MEKC). The buffers are based on the combination of a long chain alkyl acid, such as lauric acid with ammonium hydroxide or an organic base such as tris-hydroxymethylaminomethane (Tris). The resulting buffer system is able to separate neutral compounds based on its micellar properties. These buffers exhibit much reduced conductivity compared to traditional MEKC buffers, such as sodium dodecylsulfate (SDS), which contain inorganic salts. They also have inherent buffer capacity at high pH resulting from the basic buffer component, which in our studies had pK values from about 8-11. The separations that were observed showed high efficiency with plate counts in many cases above 500,000 plates per meter. The reduced conductivity allowed for the application of much higher electric fields, resulting in very fast analysis times. Alternatively, an increase in detection sensitivity could be achieved, as the reduced conductivity allowed for the use of capillaries with lager internal diameters. Combinations of different alkyl acids and organic bases provided for significant flexibility in selectivity tuning. Finally, the fact that the organic micellar buffer systems discussed here do not contain inorganic ions, allows for coupling with mass spectrometric (MS) detection. The possibility of MS detection combined with the high speed in analysis that can be obtained using these organic buffer systems, could make this approach an interesting option for high throughput analysis of combinatorial libraries.     

Characterization of buffers for electrokinetic separations

Buffers used in electrophoresis and electrochromatography must have a relatively low ionic strength in order to minimize ohmic heating in the presence of an applied potential. Calculation of pH, ionic strength, and the van Slyke buffer capacity, β, is therefore important. This paper describes thea priori calculation of these parameters for tris buffer made up with either glycine (a zwitterion) or HCl. A quadratic expression for pH, valid over wide ranges, is obtained for both buffer systems. The calculated values of pH, ionic strength, and buffer capacity are shown to agree with experimental results as a function of tris, HCl, and glycine concentrations ranging from 1 to 50 mM. A new parameter, the electrokinetic buffer effectiveness factor, is introduced to characterize buffers being considered for use in electrokinetic systems such as electrochromatography, and is used to determine the appropriate composition ranges for the buffer components.     

Chiral separation of ephedrine isomers by capillary electrophoresis using bovine serum albumin as a buffer additive

A method utilizing bovine serum albumin (BSA) as buffer additive for chiral separation by means of capillary electrophoresis is described. Parameters that affect chiral separation, such as buffer pH, buffer concentration, BSA concentration, and organic modifier, are investigated. Baseline resolution of ephedrine-pseudoephedrine and norephedrine-norpseudoephedrine isomers are achieved in an uncoated capillary with a 20 mmol/L phosphate buffer at pH 9.0 in the presence of 10 micromol/L BSA and 15% (v/v) 2-propanol at 25 degrees C. The developed method can be applied for the analysis of ephedra plant extracts that contain the four test drugs.     

Separation of cationic aracyl derivatives of betaines and related compounds

Cationic aracyl esters of betaines can be formed by alkylation with aracyl halides or trifluoromethanesulfonates. HPLC on a non-endcapped strong cation exchange (SCX) column gave high retention of these derivatives. Cation exchange HPLC may be carried out on a normal-phase (silica or alumina) column using a polar organic solvent (acetonitrile, propan-2-ol) containing an aqueous buffer with an organic cation and a hydrophilic anion. Selectivity is affected by the choice of organic solvent and buffer, e.g. alcohols decrease the retention times of hydroxybetaines such as carnitine. Retention is reduced by increasing the water content and the buffer concentration. Capillary electrophoresis migration times are affected by the choice of buffer anion, with low pH citrate buffers favoured.     

A severe peak tailing of phosphate compounds caused by interaction with stainless steel used for liquid chromatography and electrospray mass spectrometry

A severe peak tailing was observed for adenosine 5'-monophosphate in flow injection analysis with stainless steel tubing and water/methanol mixture (1:1, v/v) as carrier. The cause of the peak tailing was investigated by focusing on the chemical structure of the analytes, the material used for the analytical systems and the composition of the carrier. We clarified that the peak tailing was caused by the interaction between phosphate residues in the analytes and stainless steel. The severe peak tailing did not occur with stainless steel tubing when the phosphate compounds were analyzed with carrier containing phosphoric acid or phosphate buffer. The findings indicate that such ill peak profiles are usually not considerable in conventional HPLC separation because phosphoric acid or phosphate buffer is quite commonly used in eluents. In LC-MS, however, the use of phosphoric acid and phosphate buffer is usually avoided because of their non-volatility; therefore this interaction between stainless steel and phosphate compound becomes predominant and results in severe peak tailings. We also found an effective method for avoiding the interaction. When stainless parts, such as LC tubing and ESI spray capillary, were treated with phosphoric acid prior to analysis, the peak profiles of the phosphate compounds were dramatically improved, even when non-phosphate buffer is used as carrier.     

固相萃取-亲水作用色谱法测定废水中四环素类抗生素

建立了固相萃取(SPE)-亲水作用色谱法(HILIC)测定废水中金霉素(CTC)、强力霉素(DC)、四环素(TC)和土霉素(OTC) 4种四环素类抗生素(TCs)残留的新方法.水样经Oasis HLB固相萃取柱净化富集后, 采用以氨基色谱柱及高极性有机溶剂-水相缓冲溶液为流动相的亲水作用色谱法(HILIC)进行分析. 对流动相中缓冲溶液的类型和pH值、离子强度、 有机溶剂的浓度以及流速进行了优化, 确定了以V(乙腈)∶V(6.7 mmol/L柠檬酸铵缓冲溶液, pH 4.0)=85∶ 15混合液为流动相的最佳条件.本方法具有良好的线性关系(r> 0.999)和重现性(峰面积RSD<1.0%), 最低检出限(S/N=3)为12～30 μg/L, 4种四环素类药物添加水平在0.5～10 μg/L范围内的标准加入回收率为 90.6%～106.5%; 相对标准偏差为 2.5%～6.2%.本方法简便、准确、流动相离子强度低,适合于与质谱联用,用于屠宰场污水及医院污水等实际样品检测,结果满意.     

Purity control of oxytetracycline by capillary electrophoresis

The applicability of capillary electrophoresis for the purity control of oxytetracycline (OTC) was investigated. OTC is a broad-spectrum antibiotic belonging to the group of the tetracyclines. Several related substances can be present due to fermentation or degradation, such as 4-epioxytetracycline, -apooxytetracycline, β-apooxytetracycline, anhydrooxytet racycline, 2-acetyl-2-decarboxamidooxytetracycline, tetracycline and 4-epitetracycline. Using fused-silica capillaries, the influence of buffer type, buffer pH and buffer concentration were investigated. In all cases 1 mM EDTA was added to prevent metal-ion complexation. The influence of the buffer counter-ion type was examined. Consequently, some instrumental parameters were changed such as capillary length and diameter as well as capillary temperature and applied voltage. The following method is finally proposed: fused-silica capillary, l (effective length) = 38 cm, L (total length) = 44 cm, 50 μm I.D.; buffer, sodium carbonate 20 mM-EDTA 1 mM, pH 11.25; voltage, 10 kV; temperature, 10°C. Linearity, limit of detection and limit of quantitation were determined as well as the relative standard deviations for all the analytes involved. This method is less selective then existing liquid chromatographic methods but it may be used as a complementary tool in purity control and stability studies.     

Macrocyclic polyamine as a selective modifier in a bonded-phase capillary column for the electrophoretic separation of aromatic acids.

The use of a macrocyclic polyamine, 28[ane]-N6O2, as a selective modifier in a bonded-phase capillary column for the electrophoretic separation of 14 aromatic acids is described. Parameters that affect the performance of the separations, such as the type of buffer, the pH and concentration of buffer, the applied potential and the injection mode were studied. By changing the buffer pH (4.0-5.0), buffer concentration (10-50 mM) and applied potential (-10 approximately -20 kV), optimum conditions were obtained at -20 kV, using an acetate buffer (20 mM, pH 4.5), hydrodynamic injection with a vacuum at the buffer reservoir on the detector side and detection at 220 nm. The results showed that the separation was effective under these conditions. The plate number was greater than 4 x 10(4) m-l. Due to the wide variation in the mobilities of the test compounds, injection studies suggested that a vacuum at the buffer reservoir on the detector side would produce a result that is more representative of the initial sample composition. Benzoic acid in soy sauce, salicylic acid in Salic ointment and Aspirin were sampled and analyzed using the established conditions.     

Micellar electrokinetic capillary chromatography for the separation of cefalexin and its related substances

Micellar electrokinetic capillary chromatography (MEKC) was examined for analysis of cefalexin and its related substances. Good selectivity was obtained with two different buffer solutions: a sodium acetate buffer (50 mM, pH 5.25) containing sodium dodecyl sulfate (50 mM SDS) or sodium phosphate buffer (40 mM, pH 7.0) containing 100 mM SDS. Both methods permit cefalexin to be completely separated from its ten related substances within 20 min. The robustness of the method, using pH 5.25 acetate buffer, was examined by means of a full-fraction factorial design to test the influence of buffer pH, concentration of SDS and buffer concentration. The parameters for validation such as linearity, precision, limit of detection and limit of quantitation are also reported. The results show that method 1 is suitable for the analysis of cefalexin.     

卤代乙酸及其结构相近化合物的高效毛细管电泳分离

氟、氯、溴等卤代乙酸是结构非常相近的离子型化合物,对它们的分离测定比较困难。用高效毛细管电泳法在碱性或酸性缓冲液条件下可将它们分离。在酸性缓冲液条件下,可提高有机酸分离的选择性。较低的操作电压有利于提高阴离子的分离度,而改变温度对分离度的影响不大。     

毛细管电泳中影响径向电场控制电渗的主要因素

利用自制的二维电场毛细管电泳系统研究了不同因素对径向电场控制电渗能力的影响,发现缓冲液的ｐＨ值、浓度、种类以及管壁表面状态、管径等对电渗的电场调控有关键性的影响。有趣的是,添加剂不影响电场的调控能力,而杯芳烃涂层毛细管却能提高电渗对径向电场的响应能力。利用这种涂层效应有可能实现较高ｐＨ值下电渗的电场调控。     

Rapid enantiomeric separation of polychlorinated biphenyls by electrokinetic chromatography using mixtures of neutral and charged cyclodextrin derivatives

Electrokinetic chromatography with cyclodextrin derivatives (CD-EKC) was used to achieve the rapid enantiomeric separation of chiral polychlorinated biphenyls (PCBs). Thirteen of the 19 chiral PCBs stable at room temperature were individually separated into their two enantiomers by using 2-morpholinoethanesulfonic acid (MES) buffer (pH 6.5) containing carboxymethylated gamma-cyclodextrin (CM-gamma-CD) as pseudostationary phase mixed with beta-cyclodextrin (beta-CD) or permethylated beta-cyclodextrin (PM-beta-CD). Urea was also added to increase the solubility of PCBs and cyclodextrins in the aqueous separation buffer. Several experimental parameters such as the nature, concentration, and pH of the buffer, nature and concentration of the cyclodextrin derivatives used, and the addition of different additives were studied in order to improve the enantiomeric separation. In addition, the effect of some instrumental parameters such as separation temperature and applied voltage was also investigated. PCBs were enantiomerically separated in less than 12 min by using a 50 mM MES buffer (pH 6.5) containing 20 mM CM-gamma-CD, 10 mM beta-CD or 20 mM PM-beta-CD, and 2 M urea at a temperature of 45 degrees C and an applied voltage of 20 kV.     

Reaction of mercury(II) and xylenol orange-I Effect of the buffering media

The influence of the buffering medium on the reaction of Hg(II) with Xylenol Orange has been studied. Amine-type compounds are complexed by Hg(II)/Xylenol Orange with a sharp hyperchromic effect on the reagent itself, at 590 nm, but complex formation of Hg(II)/Xylenol Orange in non-amine-type buffer, such as citric acid-phosphate, gives a hypochromic effect on Xylenol Orange at 580 nm. Hg(II) is determined at pH 7.5 in two ranges of concentration, 2-9 ppm in citrate buffer, measured at 580 nm ( = 2.50 x 10(4)), and 6-11 ppm in hexamine buffer, at 590 nm ( = 4.18 x 10(4)).     

Metal ion capillary zone electrophoresis with direct UV detection: determination of transition metals using an 8-hydroxyquinoline- 5-sulphonic acid chelating system

The application of capillary zone electrophoresis to the separation and determination of metal ions after the precolumn formation of negatively charged chelates is described. Multi-component mixtures of transition metal complexes with 8-hydroxyquinoline-5-sulphonic acid (HQS) were separated in about 10 min in a fused-silica capillary column with a borate buffer of pH 9.2 at an applied voltage of 15 kV followed by direct UV detection. The capillary pretreatment with an electroosmotic flow modifier, namely a tetraalkylammonium salt, is necessary to achieve resonable migration times of these metal complexes. Incorporating the chelating reagent in the electrophoretic buffer markedly improves the detectability of relatively unstable chelates, such as those of Co(II), Zn(II) and Cd(II), and allows the separation of metal ions that form unstable HQS chelates, such as Mn(II) and alkaline earth metals. The effects of electrophoretic buffer parameters affecting the complexation reaction and migration behaviour are discussed. Linearity of calibration graphs is observed for about three orders of magnitude with sub-ppm detection limits. The applicability of the method to the analysis of real samples is demonstrated.     

Applications of a sulfonated-polymer wall-modified open-tubular fused-silica capillary in capillary zone electrophoretic separations

A fused-silica capillary that is wall-modified via chemically bonding a sulfonated polymer to the capillary wall has a uniform negative charge density on its surface and produces an electroosmotic flow (EOF) greater than 4 x 10(-4) cm2 V(-1) s(-1) The EOF is nearly independent of buffer pH over the pH range of 2 to 10 and is lower than the EOF obtained for the bare fused-silica capillary at the more basic pH but is higher at the more acidic buffer pH. Optimization of buffer pH can be based on analyte pKa values to improve the overall quality of the capillary zone electrophoresis (CZE) separation of complex mixtures of weak acid and base analytes. Because of the high EOF in an acidic buffer, the capillary is useful for the separation of weak organic bases which are in their cation forms in the acidic buffer. EOF for the sulfonic acid bonded phase capillary can be adjusted via buffer additives such as organic solvent, tetraalkylammonium salts, multivalent cations and alkylsulfonic acids. The advantages of utilizing buffer pH and the EOF buffer modifiers to enhance migration time, selectivity, and resolution in CZE separations with this capillary are illustrated using a series of test analyte mixtures of inorganic anions, carboxylic acids, alkylsulfonic acids, benzenesulfonic acids, sulfas, pyridines, anilines or small-chain peptides.     

Density measurements of potassium phosphate buffer from 4 to 45 degrees C

Potassium phosphate buffer is often used in methods such as equilibrium dialysis, high performance liquid chromatography (HPLC), and affinity capillary electrophoresis (ACE) for characterizing the binding of drugs and hormones with proteins or other ligands within the body. In these experiments, the buffer density is often approximated to be that of water and the concentrations of all reagents are assumed to be constant with temperature. However, some difference in density between phosphate buffer and water would be expected, and variations in this density could lead to significant changes in the concentrations of dissolved solutes with temperature. This, in turn, could affect the binding observed for a solute-ligand system in such a buffer. In this study, the densities of potassium phosphate buffers with concentrations up to 0.10 M were measured at or near physiological pH for temperatures ranging from 4-45 °C. The general change in density versus temperature followed a quadratic equation, while the changes in density with concentration and pH followed a linear response. The results were used to formulate a general equation that could be used to calculate the density of potassium phosphate buffer at any pH, temperature, and concentration within the tested range. This equation and more specialized relationships developed in the temperature, concentration, and pH studies were found to give much greater accuracy in describing the density of these buffers versus a previous relationship developed for solutions containing only potassium dihydrogen phosphate.     

High-salt stacking principles and sweeping: comments and contrasts on mechanisms for high-sensitivity analysis in capillary electrophoresis

High-salt stacking in electrokinetic chromatography (EKC) is defined and contrasted to the sweeping method. A recent paper argued the two methods are identical, where high concentrations of micelle in the sample were intended to mimic the effect of high-salt stacking. However, high micelle concentration in the sample matrix in EKC is analogous to using a high-conductivity sample instead of a low-conductivity sample in field amplified stacking. High-salt stacking does not require a sample free of pseuostationary phase, only a sample with a high-mobility co-ion compared to the separation buffer electrokinetic vector. High-salt stacking uses a discontinuous buffer system and should not be confused with continuous buffer stacking systems such as sweeping.     

Derivation of substructures from infrared band shapes by fuzzy logic and partial cross correlation functions

 Cyclic voltammetry of iron-EDTA and iron-DETPA, in different supporting electrolytes showed electrochemical reversibility in ammonium citrate at pH 8.0, while quasi-reversible nature was noticed with iron-NTA. The absence of electroactive peaks when adding a polyhydric alcohol such as mannitol (providing greater stability to the chelate in alkaline pH) or a tertiary amine such as triethanolamine (as an organic buffer) to the supporting electrolyte enabled the use of CV for quantitative analysis of iron in a complex matrix containing these ingredients. The decrease in the diffusion coefficient of Fe(III)-chelate with an increase in the organic buffer suggested the need for limiting the concentration of the amine in order to obtain efficient mass transport while providing better pH control, when such a solution is required for the oxidation of the sulfide/hydrosulfide ion to elemental sulfur. Received: 6 June 1995/Revised: 23 January 1996/Accepted: 24 January 1996     

Contribution of Tris Buffer on Xylitol Enzymatic Production

Xylitol enzymatic production can be an alternative to chemical and microbial processes, because of advantages like higher conversion efficiency. However, for an adequate conversion, it is necessary to investigate the effect of many parameters, such as buffer initial concentration, pH, temperature, agitation, etc. In this context, the objective of this work was to evaluate xylitol enzymatic production under different Tris buffer initial concentrations in order to determine the best condition for this parameter to begin the reaction. The best results were obtained when Tris buffer initial concentration was 0.22 M, reaching 0.31 g L^?1 h^?1 xylitol volumetric productivity with 99% xylose–xylitol conversion efficiency. Although the increase in buffer concentration allowed better pH maintenance, it hindered the catalysis. The results demonstrate that this bioreaction is greatly influenced by involved ions concentrations.