纳米Si/C/N复相粉体的微波介电特性

研究了纳米Si/C/N复相粉体在8.2—18GHz的微波介电特性,采用双反应室激光气相合成纳米粉体装置,以六甲基二硅胺烷((Me₃Si)₂NH)(Me∶CH₃)为原料,用激光诱导气相反应法合成纳米Si/C/N复相粉体,复相粉体的粒径为20—30nm.纳米Si/C/N复相粉体与石蜡复合体的介电常量的实部(ε′)和虚部(ε″)以及介电损耗角正切(tan δ=ε″/ε′)随纳米粉体含量的增加而增大,ε′和ε″与纳米粉体体积分数(v)之间符合二次函 关键词： 纳米Si/C/N复相粉体 微波介电常量 微观结构     

Magnetic and structural properties of nitrified FINEMET powder using mechanical milling method

The magnetic and structural properties of FINEMET [Fe_73.5Si_13.5B₉Nb₃Cu₁ wt%] amorphous powder were investigated after nitrification and mechanical milling. Fe-based amorphous powder were nitrified and crystallized simultaneously at 550 °C using by ammonia (NH₃) gas. Nitrified powder exhibited iron nitride phase such as γ′-Fe₄N, Fe₃N, and α″-Fe₁₆N₂. Nitrified particles were more brittle than raw particles. As a result, nanometer-sized nitride powder was fabricated by high-energy ball milling method. The saturation magnetization (M_s) and coercivity (H_c) of nitrified powder were increased due to nitride phase.     

On the profile of temperature dependent electrical and dielectric properties of Au/SiO2/n-GaAs (MOS) structures at various frequencies

The temperature (T) dependence of electrical and dielectric characteristics such as series resistance (R_s), dielectric constant (ε′), dielectric loss (ε″), dielectric loss tangent (tan δ), and real and imaginary part of electrical modulus (M′ and M″) of the Au/SiO2/n-GaAs (MOS) structures have been investigated in the temperature range of 80–350 K at various frequencies by using experimental capacitance (C) and conductance (G/w) measurements. Experimental results show that both C and G/w characteristics were quite sensitive to frequency and temperature at especially high temperatures and low frequencies due to a continuous density distribution of interface states and their relaxation time, and thermal restructuring and reordering of the interface. Series resistance values of this device obtained from Nicollian method decrease with increasing frequency and temperature. The ε′, ε″, tan δ, and M′ and M″ were found a strong function of frequency and temperature. While the values of ε′, ε″, and tan δ decrease, M′ and M″ increase with increasing frequency. Also, while ε′ and ε″ increase, M′ and M″ decrease with increasing temperature. The tan δ and M′ values are almost independent temperature especially at high frequencies (f≥500 kHz).     

Examining the redox and formate mechanisms for water–gas shift reaction on Au/CeO2 using density functional theory

We perform DFT calculations to investigate the redox and formate mechanisms of water–gas-shift (WGS) reaction on Au/CeO₂ catalysts. In the redox mechanism, we analyze all the key elementary steps and find that the OH cleavage is the key step. Three possible pathways of OH cleavage are calculated: (1) OH_ad^″+*^′→H_ad^′+O_ad^″; (2) H_ad^′+OH_ad^″→H₂(g)+O_ad^″+*^′; and (3) OH_ad^″+OH_ad^″→2O_ad^″+H₂(g) (*′: the free adsorption sites on the oxides; ad′: adsorption on the metal; ad″: adsorption on the oxide, respectively). In the formate mechanism, we identify all the possible pathways for the formation and decomposition of surface formates in the WGS reaction. It is found that there is a shortcoming in the redox and formate mechanisms which is related to surface oxygen reproduction. Four possible pathways for producing surface oxygen are studied, and all the barriers of the four pathways are more than 1 eV. Our results suggest that the processes to reproduce surface oxygen in the reaction circle are not kinetically easy.     

The emission spectrum of the diatomic radical, phosphorus selenide

The emission spectrum of the PSe radical is reported for the first time. Seventy-eight reddegraded bands in the region 4000–6500 Å have been measured and assigned to the A²Π-X²Π transition of PSe. Isotope shifts observed for some bandheads have been utilized in deriving the vibrational numbering. The molecular constants have been determined as (in units of cm⁻¹): ω′ = 406.9, ω′_eχ′_e = 1.3, ω″ = 556.9, ω″_eχ″_e = 1.3, and T_e = 19477.3 for the ²Π_1/2 states; and ω′_e = 402.4, ω′_eχ′_e = 1.5, ω″_e = 556.8, ω″_eχ″_e = 1.6, and T_e = 19178.0 for the ²Π_3/2 states.     

Analysis of the 2ν3 band of CD3F at 5.06 μm recorded under high resolution

The 2ν₃(A₁) band of ¹²CD₃F near 5.06 μm has been recorded with a resolution of 20–24 × 10⁻³ cm⁻¹. The value of the parameter (α^B − α^A) for this band was found to be very small and, therefore, the K structure of the R(J) and P(J) manifolds was unresolved for J < 15 and only partially resolved for larger J values. The band was analyzed using standard techniques and values for the following constants determined: ν₀ = 1977.178(3) cm⁻¹, B″ = 0.68216(9) cm⁻¹, D″_J = 1.10(30) × 10⁻⁶ cm⁻¹, α^B = (B″ − B′) = 3.086(7) × 10⁻³ cm⁻¹, and β^J = (D″_J − D′_J) = −3.24(11) × 10⁻⁷ cm⁻¹. A value of α^A = (A″ − A′) = 2.90(5) × 10⁻³ cm⁻¹ has been obtained through band contour simulations of the R(J) and P(J) multiplets.     

Solid-state NMR investigations of Si-29 and N-15 enriched silicon nitride

We compare ²⁹Si magic-angle spinning (MAS) nuclear magnetic resonance (NMR) spectra from the two modifications of silicon nitride, α-Si₃N₄ and β-Si₃N₄, with that of a fully (²⁹Si, ¹⁵N)-enriched sample ²⁹Si₃¹⁵N₄, as well as ¹⁵N NMR spectra of Si₃¹⁵N₄ (having ²⁹Si at natural abundance) and ²⁹Si₃¹⁵N₄. We show that the ¹⁵N NMR peak-widths from the latter are dominated by J(²⁹Si–¹⁵N) through-bond interactions, leading to significantly broader NMR signals compared to those of Si₃¹⁵N₄. By fitting calculated ²⁹Si NMR spectra to experimental ones, we obtained an estimated coupling constant J(²⁹Si–¹⁵N) of 20 Hz. We provide ²⁹Si spin-lattice (T₁) relaxation data for the ²⁹Si₃¹⁵N₄ sample and chemical shift anisotropy results for the ²⁹Si site of β-Si₃N₄. Various factors potentially contributing to the ²⁹Si and ¹⁵N NMR peak-widths of the various silicon nitride specimens are discussed. We also provide powder X-ray diffraction (XRD) and mass spectrometry data of the samples.     

Mechanical and electrical characteristics of silver stabilizer layer prepared by using nano silver paste for coated conductor

Mechanical and electrical properties of silver stabilizer layer of coated conductor, which was prepared using nano silver paste as starting materials, have been investigated. Nano silver paste was coated on YBCO (Y₁Ba₂Cu₃O_7−δ) film by a dip coating method with a speed of 25 mm/min. Coated film was dried in air and heat treated at 400–700 °C in a flowing oxygen atmosphere. Adhesion strength between YBCO and silver layer was measured by Tape test (ASTM D 3359). The hardness and electrical conductivity of the sample were measured by pencil hardness test (ASTM D 3363). Surface and volume resistance were measured by using LORESTA-GP (MITSUBISHI). The sample heat treated at 500 °C showed poor adhesiveness of 1B but it is clearly enhanced to 5B when samples were heat treated at higher than 600 °C. The silver layer heat treated at 700 °C showed a high hardness value of higher than 9H and a volume resistance of 1.417 × 10⁻⁷ Ω mm at room temperature. SEM observations showed that a dense silver layer was formed with a thickness of about 2 μm. Dip coated silver layer prepared by using nano silver paste showed superior electrical and mechanical characteristics which is comparable to those that sputter deposited Ag layer.     

Fourier spectrometry: Rovibrational analysis of an infrared Π → Σ system of yttrium monoiodide

The infrared spectrum of yttrium monoiodide has been excited in an electrodeless microwave discharge and explored between 2500 and 12 000cm⁻¹ with a high-resolution Fourier transform spectrometer. A unique system is observed (ν₀₀ = 9905.520 cm⁻¹), which we attribute to a ¹Π → ¹Σ transition and an extensive analysis is made. Rovibrational constants are obtained for both states mainly from a simultaneous multiband fitting. This procedure is applied to the whole set of 2231 observed line wavenumbers in the 1-0, 0-0, and 0–1 bands, yielding a final weighted standard deviation of 0.0038 cm⁻¹. Furthermore, a partial analysis of the 2-0 and 3-1 bands is performed. The following equilibrium constants are derived (cm⁻¹): ω′_e=192.210 ω′_ex′_e=0.463B′_e=0.0399133 α′_e=0.0001150ω″_e=215.815 ω″_ex″_e=0.514B″_e=0.0422163 α″_e=0.0001125 High-order constants D_v and H_v are also calculated for the various vibrational levels (v′ = 0, 1, 2, 3; v″ = 0, 1).     

Correlation between P chemical shift tensor and local structure in lithium cyclohexaphosphates Li6P6O18·3H2O and Li6P6O18

To understand the surprising behavior between the variations of the P′–P–P″ angles and the correlated variations of the O′–P–O″ ones, two lithium cyclohexaphosphate compounds Li₆P₆O₁₈·3H₂O and Li₆P₆O₁₈ are studied by solid state nuclear magnetic resonance (NMR) spectroscopy. The two compounds exhibit the same [P₆O₁₈]⁶⁻ ring anions but with 3m or internal symmetry, respectively. Such symmetries induce local distortions that are exhibited by NMR spectroscopy. One-dimensional (1D) NMR gives information on structural sites of ⁷Li and ³¹P ions and the crystallographic non-equivalencies are observed. Nevertheless, in the anhydrous compound, X-ray diffraction and NMR results do not completely agree and some discrepancy exists between the number of sites observed with the first technique and the number of lines exhibited in the NMR spectra either for ⁷Li or ³¹P nuclei. This problem is elucidated by using 2D double quantum NMR spectroscopy coupled with theoretical considerations. We find that the ³¹P chemical shift tensor is dependent on the deviations of the O–P–O angles from those in the regular tetrahedron. Within the same empirical model, we suggest that the surprising behavior between the variations of the P′–P–P″ and the ones of the O′–P–O″ is related to the overall charge on the PO₄ group. We also find the positions of the isotropic lines for ⁷Li essentially depend on the site co-ordination of this nuclei.     

Ultrasonic-assisted preparation of nano eggshell powder: A novel catalyst in green and high efficient synthesis of 2-aminochromenes

The nano eggshell powder (NESP) has been prepared by ultrasound irradiation and used as a novel and biodegradable catalyst with high catalytic activity and reusability in green synthesis of 2-aminochromenes via condensation of α- or β-phathol, malononitrile and aromatic aldehydes at 120 °C under solvent-free conditions. The reaction proceeds to completion within 10–35 min in 91–98% yield. Nano eggshell catalyst was characterized by scanning electron microscopy, X-ray powder diffraction, IR spectroscopy and X-ray fluorescence, thermal gravimetric, surface area and elemental analyses. In addition, the catalytic activity and chemical structure of nano-sized eggshell were compared with pure CaCO₃.     

Magnitudes and Orientations of the N Chemical Shift Tensor of [1-N]-2′-Deoxyguanosine Determined on a Polycrystalline Sample by Two-Dimensional Solid-State NMR Spectroscopy

The magnitudes and orientations of the ¹⁵N chemical shift tensor of [1-¹⁵N]-2′-deoxyguanosine were determined from a polycrystalline sample using the two-dimensional PISEMA experiment. The magnitudes of the principal values of the ¹⁵N chemical shift tensor of the N1 nitrogen of [1-¹⁵N]-2′-deoxyguanosine were found to be ς₁₁ = 54 ppm, ς₂₂ = 148 ppm, and ς₃₃ = 201 ppm with respect to (¹⁵NH₄)₂SO₄ in aqueous solution. Comparisons of experimental and simulated two-dimensional powder pattern spectra show that ς_33N is approximately collinear with the N–H bond. The tensor orientation of ς_33N for N1 of [1-¹⁵N]-2′-deoxyguanosine is similar to the values obtained for the side chain residues of ¹⁵N_ε1-tryptophan and ¹⁵N_π-histidine even though the magnitudes differ significantly.     

Reduction of hysteresis loss and large magnetocaloric effects in substituted compounds of itinerant-electron metamagnets La(FexSi1−x)13

The maximum value of hysteresis loss E_h^MAX due to the itinerant-electron metamagnetic (IEM) transition of La(Fe_xSi_1−x)₁₃ and the partially substituted compounds La_1−zCe_z(Fe_0.86Si_0.14)₁₃ and La_1−z′Pr_z′(Fe_0.86Si_0.14)₁₃ increases when the magnetocaloric effects (MCEs) become large. It should be noted that the reduction of E_h^MAX without the decrease of large MCEs is achieved in La_1−zCe_z(Fe_0.86Si_0.14)₁₃ and La_1−z′Pr_z′(Fe_0.86Si_0.14)₁₃. For both the compound systems mentioned above, the critical temperature T₀ for the IEM transition decreases and the difference between T₀ and the Curie temperature T_C becomes larger with decreasing T_C. These results are consistent with the magnetic phase diagram of La(Fe_0.86Si_0.14)₁₃ under hydrostatic pressure. Consequently, the reduction of E_h^MAX in La_1−zCe_z(Fe_0.86Si_0.14)₁₃ and La_1−z′Pr_z′(Fe_0.86Si_0.14)₁₃ is closely related with the magnetovolume effects.     

On the spectroscopy in ee annihilation

The properties of the radial excitations of the , ω and mesons are discussed. In particular it is proposed to identify the recently observed states at √s 1.5, 1.82 and 2.13 GeV in e⁺e⁻ annihilation with the _D ≡ ³D₁(λλ), ″ and ′″ mesons respectively. The ′ meson is suggested to lie in the vicinity of 1.5 GeV and strongly coupled to the _D. The ″(1.6) width is also suggested to be smaller than previously reported.     

In-situ synchrotron X-ray absorption studies of LiMn0.25Fe0.75PO4 as a cathode material for lithium ion batteries

Recently, lithium bi-metal phosphates (LiM′M″PO₄) have been synthesized for use as cathode materials in order to increase cell voltages and electrical performances. In this work, we have substituted Mn²⁺ at the 4c site of LiFePO₄ to prepare the lithium bi-metal phosphate LiMn_0.25Fe_0.75PO₄ and have found that it greatly enhances the cell voltage. At a 0.05 C discharge rate, the cell capacity was about 153 mAhg^− 1 and the average working voltage rose to 3.53 V due to the Mn substitution. However, the capacity and working voltage both decrease as the discharge rate increases. By in-situ metal K-edge absorption analysis, it reveals that the substituted metal Mn²⁺ does not work completely at a higher discharge rate, due to poor electrical conductivity and a serious Jahn–Teller effect.     

Photoluminescence characterization of air exposed AlGaAs surface and passivated ex situ by ultrathin silicon interface control layer

Using the photoluminescence surface state spectroscopy (PLS³) technique, attempts were made to determine the surface state density (N_ss) distribution on Al_xGa_1−xAs (x≈0.3) surfaces passivated by the Si interface control layer (ICL) technique. Air-exposed AlGaAs epitaxial wafers which are technologically important for fabrication of various devices were passivated ex situ by forming a SiO₂/Si₃N₄/Si ICL/AlGaAs structure after the HCl treatment and their photoluminescence behavior was investigated in detail. The result of the PLS³ analysis indicated that Si ICL-based passivation reduces the minimum interface state density value down to 10¹⁰ cm⁻² eV⁻¹ range. Some indication was also obtained that further improvements are possible by using electron cyclotron resonance (ECR)-enhanced N₂ plasma for Si₃N₄/Si ICL interface formation.     

Low-temperature formation of nanocrystalline SiC particles and composite from three-layer Si/C/Si film for the novel enhanced white photoluminescence

In this article, nanocrystalline silicon carbide (nc-SiC) and composite have been synthesized at an annealing temperature as low as 750 °C through the thermal reaction of Si/C/Si multilayers deposited on the Si(100) substrate by ultra-high-vacuum ion beam sputtering (UHV IBS) compared with the conventional thermal formation of crystalline SiC (c-SiC) nanostructures above 1,000 °C. The evolution of microstructure and reaction between C and Si was examined by Raman spectroscopy, Fourier transform infrared spectrometer (FTIR), high-resolution field emission scanning electron microscope (HR-FESEM), and high-resolution transmission electron microscopy. The c-SiC nanoparticles (np-SiC) of around 20–120 nm in diameter appeared on the top and bottom of the three-layer film with a particle density of around 2.63 × 10¹⁰ cm⁻² after 750 °C annealing. The composite of nc-SiC and Si nanocrystals (nc-Si) size below 5 nm embedded in an amorphous SiC (a-SiC) matrix appeared at the interface between the Si and C layers. Efficient thermal energy is the driving force for the formation of nc-SiC and composite through interdiffusion between C and Si. The broad visible photoluminescence (PL) spectrum of 350–750 nm can be obtained from the annealed composite Si/C/Si multilayer and deconvoluted into four bands of blue (~430 nm), green (~500 nm), green–yellow (~550 nm), and orange (~640 nm) emission, corresponding to the emission origins from nc-SiC, sp² carbon clusters, np-SiC, and nc-Si, respectively.     

New ferromagnetic La3Co2TaO9 double perovskite: Structural and magnetic properties

The new double perovskite La₃Co₂TaO₉ has been prepared by a solid-state procedure. The crystal and magnetic structures have been studied from X-ray powder diffraction (XRPD) and neutron powder diffraction (NPD) data. Rietveld refinements were performed in the monoclinic space group P2₁/n. The structure consists of an ordered array of alternating B′O₆ and B″O₆ octahedra sharing corners, tilted along the three pseudocubic axes according to the Glazer notation a⁻b⁻c⁺. Rietveld refinements show that at RT the cell parameters are a=5.6005(7) Å, b=5.6931(7) Å, c=7.9429(9) Å and β=89.9539(7)°, and the refined crystallographic formula of this “double perovskite” can be written as La₂(Co)_2d(Co_1/3Ta_2/3)_2cO₆. Magnetization measurements and low-temperature NPD data show that the perovskite is a ferromagnet with T_C=72 K. At high T it follows the Curie–Weiss law with an effective magnetic moment of 3.82μ_B per Co ion which is very close to spin only Co²⁺ (HS).     

Resonance excitation process for Ni-like gold

A detailed and large-scale calculation on the resonant excitation rate coefficients from the ground state to the 106 fine-structure levels belonging to 3l¹⁷4l^′(l=0,1,2;l^′=0,1,2,3) configurations of Ni-like gold have been performed using the relativistic distorted-wave approximation. The contributions through all possible Cu-like doubly excited states 3l¹⁷4l^′n^″l^″and 3l¹⁷5l^′n^″l^″(n^″≤15,l^″≤8) are calculated explicitly. The radiative damping effects on resonant excitation rates are studied. Significant effects arising from decays to autoionizing levels are also investigated. The n⁻³scaling law is investigated and is used to obtain the contributions from high-n configurations. Contributions from resonant excitation are found to be as important as direct excitation processes for most transitions. In some cases, resonant excitation can enhance the excitation rate coefficients by an order of magnitude. In addition, the total dielectronic recombination rate coefficients of Ni-like gold are also presented and compared with other works.     

Synthesis and characterization of nano silver ferrite composite

We report the synthesis of nano sized silver ferrite composite having the empirical formula AgFeO₂ by a co-precipitation method. The resulting powders are thin platelets, transparent and a rich ruby red in color in transmission. The X-ray diffraction (XRD) powder data consisted of only nine reflections, and the analysis showed the unit cell to be rhombohedral. The powders showed extensive XRD line broadening and the sizes of the crystals are calculated to be in the range 4-36.5 nm. The morphology of the silver ferrite composite studied using scanning electron microscope showed nano sized particles. The particle size is found to increase with increase in annealing temperature. The magnetic behavior, measured using a vibrating sample magnetometer, indicated a change from paramagnetic to ferromagnetic with increase in particle size.