甲烷在SrO-La_2O_3/CaO催化剂上的氧化偶联 Ⅰ.SrO对La_2O_3/CaO催化剂的助催化作用

在常压流动反应装置上评价了一系列La_2O_3/CaO催化剂和SrO-La_2O_3/CaO催化剂。实验表明:La_2O_3/CaO体系是很好的甲烷氧化偶联催化剂。在1073K和CH_4:O_2:He=4:1:5(总流速120ml/min)的实验条件下,20％La_2O_3/CaO催化剂上的甲烷转化率为26％,C_2选择性为53％;加入助剂SrO(15—20％)后,在同样实验条件下,甲烷转化率为29％,C_2选择性为66％。表明SrO对La_2O_3/Cao催化剂有明显的促进作用。用XRD,XPS和TPD(CO_2-TPD和O_2-TPD)技术表征了SrO-La_2O_3/CaO催化剂体系,结合反应评价结果,认为SrO的促进作用可以归结为:(1)调变了催化剂的碱性强度分布,提高了催化剂表面强碱中心的数目;(2)提高了La_2O_3的分散度;(3)抑制了催化剂的低温氧吸附物类。     

甲烷在二元碱土金属复合体系催化剂上的氧化偶联

碱土金属氧化物或碳酸盐为多种类型甲烷氧化偶联制取C_2烃催化剂的重要组分之一.有关纯碱土金属氧化物及含氧酸盐的研究表明,这类化合物具有较强的表面碱性及高温P型半导性而对活化甲烷生成C_2烃有较高活性,关于不同碱土金属化合物之间混合形成的二元碱土金属复合体系催化剂的报导仍不多见,Aika等人曾报导用BaO与CaO或MgO混合的催化剂上在1073K时可以获得61.1%C_2烃选择性和14.2%的C_2烃收率,但BaO易在反应条件下与水反应生成Ba(OH)_2而腐蚀器壁,不利于长期操作.本文报导了一系列不同碱土金属化合物之间形成的二元碱土复合体系催化剂上甲烷氧化偶联的反应结果.结果表明,这类催化剂由于其结构稳定、活性好而值得进一步研究.     

La-Ba系氧化物催化剂用于甲烷氧化偶联

以La_2O_3为基础,碱土金属作为第二组分的二元氧化物催化剂均具有较高的生成C_2活性,特别是La-Ba-O系催化剂具有优良的甲烷氧化偶联活性和稳定性,当La/Ba原子比为2.5时,C_2收率可达20.3％。第三组分的添加有助于提高C_2选择性,特别是添加碱金属,可以抑制完全氧化反应,并提高乙烯/乙烷比。在La:Ba:Na=2.5:1:0.1的催化剂上进行了500/小时的寿命实验,在整个反应期间,催化剂的活性和选择性相当稳定。X-射线物相分析表明,新鲜催化剂除有少量的碳酸钡外,主要是氧化镧和氧化钡的混合物。500小时后的物相基本上是氧化镧和碳酸钡。使用前后催化剂的比表面积及表面La和Ba的分布均无改变。较高的CH_4/O_3比对提高C_2选择性有利,当CH_4:O_2=4:1时,C_2选择性和收率分别为65.1％和19.1％。     

快离子导体在甲烷氧化偶联反应中的作用

本文分别以离子型导体La_2O_3和CaO载体,添加A_2BO_4型快离子导体,发现催化剂的C_2烃收率与添加的快离子导体迁移能力有很好的顺变关系。     

锂在甲烷氧化偶联催化剂中的助催化作用

自Lunsford等首次报道在Li/MgO催化剂上的甲烷氧化偶联(OCM)以来,许多研究者相继报道了添加碱金属对该反应的影响,其中以Li的添加最受关注。Li在OCM反应中对提高C_2烃选择性的作用最为明显,因而弄清Li在这一反应中的作用十分必要。本文讨论了Li在几个有代表性的碱土(CaO)及稀土(La_2O_3)中的存在形式与生成C_2产物的关系。     

原位FT-IR研究甲烷和氧与SrO-La_2O_3/CaO催化剂表面的相互作用和反应(英文)

用原位FT－IR研究了甲烷和氧与纯CaO,La_2O_3和SrO氧化物以及LC和SLC催化剂的相互作用和反应．当不存在气相氧时,引入的甲烷与表面晶格氧反应生成碳酸盐物种。在室温或高温下,在这些氧化物和催化剂上不能检测到CH_4或O_2的吸附物类。但是,当CH_4和O_2同时存在时,在La_2O_3和LC催化剂上能检测到1118cm~－1的新谱带、这一谱带可能来自于表面碳酸盐在高温下氧气氛中的分解,并可归属为物种。甲烷与这一活性氧物种反应生成C_2H_4。但对SLC催化剂,在高温下不能检测到物种,而甲烷和氧在高温下反应也能产生表面碳酸盐并在气相中形成乙烯,这就表明,气相氧对这些催化剂也起着关键作用,但是在LC和SLC催化剂上甲烷氧化偶联反应可能有本质上的差别。     

在甲烷氧化偶联反应中碱、碱土、稀土金属氧化物之间的相互作用 Ⅱ.掺CaO的La_2O_3和掺La_2O_3的CaO催化剂的催化性能

报导了非Li催化剂CaO-La_2O_3和La_2O_3-CaO的催化性能。甲烷氧化偶联反应的活性测试表明:以共沉淀方法制备的CaO-La_2O_3催化剂除了具有较好的C_2选择性外,其活性明显高于其它样品,而且适用于较大的空速条件(100000h~(-1)),是一个有应用前景的催化剂。但这类催化剂表现出明显的热点效应。用XRD,SEM等技术研究了相应催化剂体系的晶胞参数变化规律以及颗粒分散程度,并同其催化性能进行了关联。     

La2O3/MgO催化剂上的甲烷氧化偶联

研究了甲烷在La_2O_3/MgO催化剂上的氧化偶联。发现制备过等对催化剂的行为有显著影响。比较了催化剂的反应性能和体相结构,表明在MgO上存在着三种La_2O_3的状态:高分散La_2O_3是最活泼的;La(OH)_3不太活泼;而呈六方晶相的La_2O_3晶粒活性最低。在催化剂中加入Na_2CO_3和K_2CO_3可以改进催化剂的活性和选择性。还考察了反应条件如温度和空速的影响。     

镧改性铁催化剂的研究——Ⅰ.镧改性铁催化剂的载体与活性组分的相互作用

用穆斯堡尔谱、程序升温还原和Cahn微量天平技术研究了Fe_2O_3/γ-Al_2O_3,Fe_2O_3-La_2O_3/γ-Al_2O_3和Fe_2O_3/La_2O_3/γ-Al_2O_3催化剂的载体与活性组分的相互作用。结果表明:用La_2O_3改性后的Fe_2O_3/La_2O_3/γ-Al_2O_3催化剂,载体与活性组分的相互作用加强,使FeO(Ⅱ)相得到稳定并难以还原为零价铁。同时改性的效果与La_2O_3的添加方式有关,对共浸催化剂Fe_2O_3-La_20_3/γ-Al_2O_3·La_2O_3可能仅起到助剂的作用。La_2O_3的添加还提高了催化剂的还原速度。     

甲烷氧化偶联制乙烯Li—ZrO2,Li—La2O3催化剂的研究

研究了添加Li的La_2O_3和ZrO_2两种催化剂对甲烷氧化偶联催化性能的影响,并用XRD,LRS和XPS等方法对催化剂进行了表征。结果表明,Li~+的加入提高了催化剂的C_2选择性,但两类催化剂上Li~+的添加作用机制不同。La_2O_2加入Li~+达40mol％时,样品可获得34.4％的甲烷转化率和60.4％的C_2选择性。Li~+在La_2O_3表面分散,表面O/(Li+La)比随Li~+添加量增加而下降。催化剂对C_2选择性的提高可能是因为Li~+覆盖了La_2O_3表面部分完全氧化中心所致。ZrO_2中添加Li~+有Li_2ZrO_3生成,75mol％Li-ZrO_2仅检测到Li_2ZrO_3晶相,该样品可得34％甲烷转化率和63％C_2选择性。样品的XRD及XPS研究表明,随Li~+加入量增加,表面Li/Zr比接近2:1,没有Li的富集,样品表面存在两种氧物种,其O_1s结合能分别为530.3和531.9eV。对75mol％Li—ZrO_2样品,后者占95％,该表面氧物种可能与C_2选择性提高有关。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.