Rapid and selective determination of osmium(IV) by UV-visible spectrophotometry using o-methylphenyl thiourea as a chromogenic chelating ligand: sequential separation of osmium(IV), rhodium(III) and platinum(IV)

The objective of this research work was to develop a simple, highly sensitive and precise method for spectrophotometric determination of osmium(IV). O-Methylphenyl thiourea (OMPT) coordinates with osmium(IV) as a 1:1 (osmium(IV)–OMPT) complex in hydrochloric acid media (0.8 mol l^?1). The novelty of the investigated method is instant complex formation at room temperature with no need of heating or standing. The complex is stable for more than 8 days. The method is applicable over a wide linearity range (up to 110 µg ml^?1). A low reagent concentration is required (2 ml, 0.009 mol l^?1 in ethanol). The complex exhibits maximum absorption in the range of wavelength 510–522 nm and 514 nm was selected for further study. The molar absorptivity was 1.864 × 10³ l mol^?1 cm^?1, Sandell’s sensitivity was 0.102 µg of osmium(IV) cm^?2. Proposed method was successfully applied for separation and determination of osmium(IV) from binary and ternary synthetic mixtures containing associated metal ions. A scheme for mutual separation of osmium(IV), rhodium(III) and platinum(IV) is developed.     

Adsorptive Stripping Voltammetric Determination of Antimony by Using Alizarin Red S

Abstract

A sensitive and selective voltammetric method for determination of antimony(III) using Alizarin Red S (ARS) as complexing agent is described. The method is based on the monitoring the oxidation peak of antimony(III)-ARS complex at ?520 mV in ammonium-ammonia buffer (pH = 7.5). The peak current was measured by scanning the potential from ?700 mV versus Ag/AgClto more positive potentials without accumulation in the presence of 1 × 10^?6 mol L^?1 of ARS. The limit of detection (3 s) and limit of quantification (10 s) of the method were calculated from calibration curve as 1.45 µg L^? and 4.8 µg L^? respectively. The calibration plot for antimony(III) was linear in the range of 4.8–30 µg L^?. The interference of various ions was examined. Serious interference from Al(III), Fe(III), Cu(II), Pb(II), and Zn(II) was eliminated by addition of EDTA to the solution. The method was applied to drinking water samples. The recoveries were in the range 94% – 105%. The results obtained from the developed method were compared with those from the differential-pulse anodic-stripping method and no statistically significant difference was found.     

A Direct Chemiluminescence Method for the Determination of Prulifloxacin Using Tris-(4,7-Diphenyl-1,10-Phenanthrolinedisulfonic Acid) Ruthenium(II)–Cerium(IV) System

Abstract

A simple, rapid, injection chemiluminescence method is described for the determination of prulifloxacin, a commonly used antibiotic. A strong chemiluminescence signal was detected when a mixture of the analyte and tris-(4,7-diphenyl-1,10-phenanthrolinedisulfonic acid)ruthenium(II) was injected into cerium(IV) sulfate. The chemiluminescence signal is proportional to the concentration of prulifloxacin in the range 4.0 × 10^?8–9.0 × 10^?6 mol L^?1. The detection limit is 1.0 × 10^?8 mol L^?1, and the relative standard deviation is 2.2% (n = 11) for the determination of 8.0 × 10^?7 mol L^?1 prulifloxacin. The proposed method was successfully applied to the determination of prulifloxacin in pharmaceutical preparations in capsules, spiked serum, and urine samples.     

Determination of Vitamin A in Infant Milk-Based Formulas and Pharmaceutical Formulations Using Flow Injection with Ce(IV)–Na2SO3 Chemiluminescence Detection

A rapid and simple flow injection (FI) method is reported for the determination of vitamin A (retinol) based on its strong enhancing effect on the Ce(IV)–Na₂SO₃ chemiluminescence (CL) reaction in an acidic solution. The effect of key chemical and physical parameters (i.e., reagent concentrations, flow rate, and sample volume) was optimized and potential interferences examined. Under the selected experimental conditions, a linear calibration was obtained between the CL intensity and vitamin A concentration in the range 0.1–8.0 µg mL^?1 (r ²  = 0.9986, n = 8). The limit of detection (3 s x blank) was 0.01 µg mL^?1 retinol (n = 6) and the relative standard deviation (RSD) for 0.25 µg mL^?1 retinol was 2.3% (n = 10) with a sampling rate of 180 h^?1. The method was successfully applied to infant milk-based formulas and pharmaceutical formulations and the results were not significantly different at 95% confidence interval with those obtained by using a spectrophotometric reference method. The possible CL mechanism is also discussed briefly supporting with UV-visible, fluorescence, and CL spectra.     

Simultaneous Determination of Gallium(III) and Indium(III) in Urine and Water Samples with Cloud Point Extraction and by Inductively Coupled Plasma Optical Emission Spectrometry

A simple, sensitive, and selective method for the determination of gallium and indium in different samples at trace levels is presented. This method was based on complexation of analyzes with 2-(5-bromo-2- pyridylazo)-5-diethylaminophenol (5-Br-PADAP) in the presence of t-octylphenoxy-polyethoxyethanol (Triton X-100). After phase separation, the analyzed concentrations were determined by inductively coupled plasma optical emission spectrometry. Quantitative extraction of gallium and indium was performed at pH 7.0, 1.7 mmol L^?1, 5-Br-PADAP, 1.3% (w/v) Triton X-100 and at 75°C. The relative standard deviations (RSD) of this method were between 0.3% and 1.6% (C = 20 ng mL^?1, n = 9). The calibration curve is linear over the concentration range 6–200 ng mL^?1 for gallium and 2–200 ng mL^?1 for indium, respectively. The limits of detection (LOD) for gallium and indium were 0.72 and 0.28 ng mL^?1, respectively. The results showed the developed method was not susceptible to matrix effects, providing recoveries between 98% and 102%. The accuracy of the developed method was evaluated by the analysis of spiked certified reference materials. The developed method was successfully applied to gallium and indium determination in urine and lake water with satisfactory results.     

Selective determination of selenium(IV) from environmental samples by UV-visible spectrophotometry using O-methoxyphenyl thiourea as a chelating ligand

A selective extraction–spectrophotometric method has been developed for determination of selenium(IV) using O-methoxyphenyl thiourea (OMePT) as a chelating agent. The basis of the proposed method is the spectrophotometric determination of selenium(IV)–OMePT complex obtained after extraction of selenium(IV) from 3.5 M hydrochloric acid media using OMePT in chloroform solvent. The complex shows maximum absorbance at 350 nm against the reagent blank. The Beer’s law was obeyed over the concentration range 5–60 µg mL^?1 of selenium(IV). The optimum concentration range was 20–50 µg mL^?1 as evaluated from Ringbom’s plot. The molar absorptivity and Sandell’s sensitivity of the selenium(IV)–OMePT complex in chloroform were 3.312 × 10² L mol^?1cm^?1 and 0.2384 µg cm^?2, respectively. The composition of selenium(IV)–OMePT complex was 1:2 established from slope ratio method, mole ratio method and Job’s continuous variation method. The complex was stable for more than 72 h. The interfering effect of various foreign ions was studied and suitable masking agents were used wherever necessary to enhance the selectivity of the developed method. The proposed method was successfully applied for the determination of selenium(IV) from real samples, viz. pharmaceutical formulations, shampoo, vegetable sample, synthetic mixtures and environmental samples. Repetition of the method was checked by finding the relative standard deviation (RSD) for 10 determinations which was 0.35%.     

Online thorium determination after preconcentration in a minicolumn having XAD-4 resin impregnated with N-benzoylphenylhydroxylamine by FI-spectrophotometry

A very sensitive and selective flow injection on-line determination method of thorium (IV) after preconcentration in a minicolumn having XAD-4 resin impregnated with N-benzoylphenylhydroxylamine is described. Thorium (IV) was selectively adsorbed from aqueous solution of pH 4.5 in a minicolumn at a flow rate of 13.6 mL min^?1, eluted with 3.6 mol dm^?3 HCl (5.6 mL min^?1), mixed with arsenazo-III (0.05% in 3.6 mol dm^?3 HCl stabilized with 1% Triton X-100, 5.6 mL min^?1) at confluence point and taken to the flow through cell of spectrophotometer where its absorbance was measured at 660 nm. Peak height was used for data analyses. The preconcentration factors obtained were 32 and 162, detection limits of 0.76 and 0.150 ??g L^?1, sample throughputs of 40 and 11 h^?1 for preconcentration times of 60 and 300 s, respectively. The tolerance levels for Zr(IV) and U(VI) metal ions is increased to 50-folds higher concentration to Th(IV). The proposed method was applied on different spiked tap water, sea water and biological sample and good recovery was obtained. The method was also applied on certified reference material IAEA-SL1 (Lake Sediment) for the determination of thorium and the results were in good agreement with the reported value.     

Ion-Pair LC Method for Simultaneous Determination of Aliskiren Hemifumarate,Amlodipine Besylate and Hydrochlorothiazide in Pharmaceuticals

A rapid and precise LC method was developed for the simultaneous determination of aliskiren hemifumarate (ALS), amlodipine besylate (AML) and hydrochlorothiazide (HCZ) using acetonitrile:25 mM octane sulfonic acid sodium salt monohydrate in water (60:40 v/v) as the mobile phase. The flow rate was maintained at 1.2 mL min^?1 on a stationary phase composed of Supelco, Discovery^® HS (C18) column (25 cm × 4.6 mm, 5 μm). Isocratic elution was applied throughout the analysis. Detection was carried out at λ _max (232 nm) at ambient temperature. The method was validated according to ICH guidelines. Linearity, accuracy and precision were satisfactory over the concentration ranges of 32–320, 2–44 and 4–64 μg mL^?1 for ALS, AML and HCZ, respectively. LOD and LOQ were estimated and found to be 0.855 and 2.951 μg mL^?1, respectively, for ALS, 0.061 and 0.202 μg mL^?1, respectively, for AML as well as 0.052 and 0.174 μg mL^?1, respectively, for HCZ. The method was successfully applied for the determination of the three drugs in their co-formulated tablets. The results were compared statistically with reference methods and no significant difference was found. The developed method is specific and accurate for the quality control and routine analysis of the cited drugs in pharmaceutical preparations.     

Erratum to: Evaluation of Three Multiresidue Methods for the Determination of Pesticides in Marijuana (Cannabis sativa L.) with Liquid Chromatography-Tandem Mass Spectrometry

Marijuana (non-medical cannabis) is a well-recognized psychoactive herbal drug used for recreational purposes. The aim of this work is to describe and compare the performance and suitability of selected methods to analyze pesticide residues in marijuana. The fitness of three typical pesticide multiresidue methods [acetate buffered QuEChERS (method A), a modified citrate buffered QuEChERS (method B) and citrate buffered QuEChERS (method C)] were tested in marijuana through the LC–MS/MS determination of 61 LC amenable pesticides. Considering recoveries at the highest level for the selected pesticides in marijuana, from the 61 target analytes, 37 (method A), 40 (method B) and 46 (method C) compounds gave accurate results (70–120 % range). Method C showed the best performance for the target analytes in terms of recoveries, precision, limits of quantitation and matrix effect. Marijuana showed to be a highly complex matrix. Most analytes suffered high signal suppression (ME <−50 %) for method B while medium (−50 to 20 %) to low (−20 to 0 %) signal suppression was found for methods A and C. Moreover, high coelution of coextractives with the target analytes was observed. A pilot survey with real samples revealed that seized and legally produced marijuana samples contained pesticides. Residues of diazinon (0.03 mg kg⁻¹), tebuconazole (0.19 mg kg⁻¹) and teflubenzuron (0.11 mg kg⁻¹) were simultaneously detected in one marijuana sample. The establishment of MRLs in a legal consumption scenario such as in Uruguay seems to be necessary in the near future.

     

Determination of Ferulic Acid in Rat Plasma by Liquid Chromatography–Tandem Mass Spectrometry Method: Application to a Pharmacokinetic Study

Abstract

A rapid, sensitive, and specific liquid chromatography–tandem mass spectrometric (HPLC-MS/MS) method has been developed for quantification of ferulic acid in rat plasma. The analyte and docetaxel (internal standard) were extracted from plasma samples with diethyl ether and analyzed on a C₁₈ column. The chromatographic separation was achieved within 3.5 min by using acetonitrile-water as the mobile phase and the flow rate was 0.2 mL · min^?1. The method was linear within the range of 0.5 ? 800 ng · mL^?1. The lower limit of quantification (LLOQ) was 0.5 ng · mL^?1. Finally, the method is successfully applied for the pharmacokinetic study of ferulic acid in rats following intravenous administration.     

LC Assay of Eletriptan in Tablets and In Vitro Dissolution Studies

Eletriptan (ELT) is a new selective serotonin agonist approved for the treatment of acute migraine headaches. A simple and rapid liquid chromatographic method was developed and validated for the assay of ELT in tablets. Chromatography was carried out on a 250 mm × 4.6 mm C₁₈ column at 30 °C. Acetonitrile–15 mM triethylamine solution (adjusted to pH 7.0 using concentrated o-phosphoric acid) (60:40, v/v) mixture was used as mobile phase at 1.0 mL min^?1 flow rate and UV detector was set at 225 nm. A linear response (r ²  = 0.9999) was observed in the range of 0.1–1.6 μg mL^?1. The method showed good recoveries (100.08 %) and the RSD values for intra- and inter-day precision were 0.78–1.93 and 1.10–2.15%, respectively. The method can be used for quality control assays and in vitro dissolution studies of ELT in tablets.     

Stability-Indicating Liquid Chromatography–Spectrophotometric UV Method for the Simultaneous Determination of Marbofloxacin,Dexamethasone and Clotrimazole in a Liquid Pharmaceutical Dosage Form

A novel, simple and reliable reversed-phase liquid chromatography (LC)–spectrophotometric UV stability-indicating method was developed and validated for the simultaneous assay of marbofloxacin, clotrimazole and dexamethasone acetate in the presence of their impurities and degradation products in a pharmaceutical formulation for veterinary use. A C18 (75 × 4.6 mm, 4 µm) column was used with an acetonitrile–ammonium acetate mixture as mobile phase delivered with gradient elution. A diode-array detection was used in the 200–400 nm range and the detection wavelength was set at 260 nm. Validation carried out on the pharmaceutical dosage form, according to Veterinary International Conference on Harmonization guidelines, demonstrated excellent specificity, linearity, precision, accuracy and robustness. Excellent specificity with respect to vehicle and degradation products obtained after forced degradation (i.e., oxidation, acid, alkaline and thermal degradation) was demonstrated. As for linearity, the LC–UV assay method is applicable in the 0.180–0.420 mg mL⁻¹ concentration range for marbofloxacin (r ² = 0.99), 0.060–0.140 mg mL⁻¹ for dexamethasone acetate (r ² = 0.97) and 0.600–1.400 mg mL⁻¹ for clotrimazole (r ² = 0.98). Very good repeatability (RSD < 0.8 %) and inter-day precision (RSD < 2.5 %) were observed for all analytes. Accuracy was in the 93–104 %, 98–111 % and 99–108 % confidence interval (95 %) for marbofloxacin, dexamethasone acetate and clotrimazole, respectively. The variations (±20 %) of mobile phase flow rate and pH, and oven column temperature did not exhibit an impact on the analyte content accuracy, demonstrating the robustness of the method. The LC–UV method here developed and validated may be used routinely for quality control.

     

Selective solid phase extraction and preconcentration of ultra-trace inorganic mercury in water samples using 2,6-dimethyl-morpholine dithiocarbamate

A sensitive and selective solid-phase spectrophotometric method for the determination of trace amounts of Hg(II) cation in water is described. A complex was created with Hg(II) using 2,6-dimethyl-morpholine dithiocarbamate (DMMDTC) to form Hg(II)–(DMMDTC) and this complex was adsorbed onto microcrystalline naphthalene (MN) and then eluted with 5% acetic acid (in ethanol) solution. A preconcentration factor of 187 and a recovery of 95% were observed at pH of 5.0 and for 10 min. of extraction. The separated Hg(II) ions were quantified by using ultraviolet-visible spectrophotometer at 490.0 nm by creating a colored complex with dithizone in Triton X-100 surfactant media. Molar absorptivity and sandell’s sensitivity for the Hg(II)-dithizone were determined as 4.96 × 10⁵ Lmol^?1cm^?1 and 0.4032 µg cm^?2, respectively. The detection limit (LOD) was 1.7 μg L^?1 under the optimized conditions of the analytical method.     

Fluorescence Quenching Method for Determination of Trace Tungsten in Soil after Cloud Point Extraction

A new procedure for trace tungsten W(VI) in soil by fluorescence quenching method coupled with cloud point extraction (CPE) as the separation-preconcentration method was described. The Triton X-100 CPE behavior of W(VI)-salicylfluorone (SAF)was investigated. Under the optimized conditions, the fluorescence quenched intensity (ΔF) was linearly with W(VI). The range of linear was 0.8 ～ 20.0 μg · L^?1, the detection limit (DL) was 0.14 ng · mL^?1 (3σ), the relative standard deviation 3.3% (c = 10.0 μg · L^?1, n = 5) and the recovery was 101.0–102.2%. The proposed method applied to the analysis of W(VI) in certified reference materials and real samples.     

On-line preconcentration and determination of Au(III) in various environmental/industrial samples by flame atomic absorption spectrometry

A rapid and simple on-line method is described for the determination of Au(III) in various samples. The method is based on the sorption of gold(III) on Lewatit MonoPlus TP207 chelating resin including the iminodiacetate group, which is used as sorbent material and packed in a minicolumn. The chemical variables such as the pH of the sample solution, eluent type, interfering ions and concentrations of reagents, and instrumental variables such as sample loading volume, reagents flow rates, and tubing length, which affect the efficiency of the method were studied and optimised. Au(III) was sorbed on the chelating resin, from which it could be eluted with 3 mol L^?1 HCl, and then introduced directly to the nebuliser-burner system of FAAS. The limit of detection of the method was 0.2 µg L^?1 while the relative standard deviation was <4.0% for 20 µg L^?1 Au(III) concentration. The preconcentration factor was found to be 106 while the optimised sample volume was 15.3 mL. The accuracy of the method was verified by analysing the certified reference material. The developed method was applied successfully for the determination of gold in different samples with satisfactory results.     

The determination of salivary oxypurines before and after exercise by combined liquid chromatography-field asymmetric waveform ion mobility spectrometry-time-of-flight mass spectrometry

A method combining field asymmetric waveform ion mobility spectrometry with liquid chromatography-mass spectrometry (LC-FAIMS-MS) has been developed for the analysis of the oxypurine compounds hypoxanthine (HX) and xanthine (XA) in saliva. Separation of the oxypurines from interfering matrix components was investigated using FAIMS-MS. The selected FAIMS parameters were then applied to the rapid LC-FAIMS-MS analysis of HX and XA using a short chromatographic separation method (7 min). A comparison of the LC-MS method with and without FAIMS applied, resulted in improved discrimination from saliva matrix interferences and improved chromatographic peak integration for both HX and XA using a FAIMS separation. A quantitative evaluation of the LC-FAIMS-MS method was performed giving limits of detection of 2.0 ng mL^?1 for HX and 1.8 ng mL^?1 for XA, and limits of quantification of 6.6 ng mL^?1 for HX and 6.0 ng mL^?1 for XA. The developed LC-FAIMS-MS method was applied to the targeted analysis of the oxypurine metabolites in saliva collected from healthy male athletes (n =?11) before and after exercise designed to induce oxidative stress; post-exercise collection time-points included immediately after exercise, one hour and twenty-four hours’ post-exercise. The salivary concentrations of both HX and XA were lower after physical exercise, compared to the pre-exercise (rest) concentrations and returned to approximately pre-exercise levels after twenty-four hours. The method reported has the potential for monitoring the salivary oxypurines, HX and XA, as biomarkers of oxidative stress and in other clinical applications.     

Determination of Copper in Human Urine by RP-LC After Pre-column Derivatization with Neocuproine and Use of Monolithic Column

A selective sensitive RP-LC–UV/VIS method with pre-column derivatization was developed for the determination of copper in human urine at a trace level. This method is based on the selective reaction of 2,9-dimethyl-1,10-phenanthroline (neocuproine) with copper(I) to produce a yellow-orange hydrophobic complex in a neutral or slightly acidic buffer solution (adjusted to pH 5.9). Copper(II) was reduced to copper(I) ions by ascorbic acid as a weak reducer, which was added both to urine sample and mobile phase, respectively. A hydrophobic copper(I)–neocuproine chelate was determined by RP-LC–UV/VIS using a monolithic column Chromolith Performance RP-8e (100 × 4 mm I.D.) at 30.0 ± 0.1 °C with a methanol: aqueous buffer (pH 5.9, ammonium acetate and ascorbic acid 2.8 mmol L^?1) mobile phase at flow rate of 2.00 mL min^?1. Sample injection volume was 20 μL and detection was done at 453 nm. The method was validated over a concentration range of 0.09–11.50 μmol L^?1. The LOD of copper in human urine was found to be 0.07 μmol L^?1 concentration level, suitable for clinical analysis. The precision of the results, reported as the RSD, was below 4.6 % for copper concentration within range 0.5–5.0 μmol L^?1 in the spiked human urine samples.     

Validation of an HPLC Analytical Method for Determination of Pancuronium Bromide in Pharmaceutical Injections

Abstract

Pancuronium bromide is used with general anesthesia in surgery for muscle relaxation and as an aid to intubation. A high performance liquid chromatographic method was fully validated for the quantitative determination of pancuronium bromide in pharmaceutical injectable solutions. The analytical method was performed on an amino column (Luna® 150 mm × 4.6 mm, 5 µm). The mobile phase was composed of acetonitrile:water containing 50 mmol L^?1 of 1-octane sulfonic acid sodium salt (20:80 v/v) with a flow rate of 1.0 mL min^?1 and ultraviolet (UV) detection at 210 nm. The proposed analytical method was compared with that described in the British Pharmacopoeia.     

A Novel Enhanced Chemiluminescence System with Ag(III) Complex for the Determination of Ofloxacin and Levofloxacin in Pharmaceutical Preparation and Biological Fluid

A novel chemiluminescence (CL) method is developed for determination of ofloxacin and levofloxacin with Ag(III) complex in H₂SO₄ solution medium. The CL intensity is proportional to drug concentration in a wider range with a correlation coefficient of 0.999. The limit of detection (s/n = 3) for ofloxacin and levofloxacin was 5.3 × 10^?9 g ml^?1 and 8.3 × 10^?9 g ml^?1, respectively, and their recoveries from urine and serum samples were in the range of 90.1–112% with the RSDs of 1.0–2.8%. The proposed method was applied for analysis of real samples with satisfactory result. The possible CL mechanism was discussed.     

Determination of Semicarbazide-Sensitive Amine Oxidase Activity in Blood Plasma by a Light Scattering Technique

A novel method for the determination of semicarbazide-sensitive amine oxidase (SSAO) activity in blood plasma has been developed. The method was based on the change of light scattering (LS) intensity resulting from the derivative product of the interaction of 2,4-dinitrophenylhydrazine (DNPH) with benzaldehyde produced by catalyzing of SSAO to benzylamine. In Britton-Robinson (B-R) buffer solution, the intensity of system's LS at 514.6 nm was significantly enhanced and was directly proportional to the concentration of benzaldehyde. In this method, SSAO enzyme activity is defined as the concentration of benzaldehyde (nmol) formed per mL plasma per hour. The range of determination of SSAO enzyme activity was 6.40 × 10^?3 ?0.340 nmol mL^?1 h^?1 with a detection limit of 1.92 × 10^?3 nmol mL^?1 h^?1. The relative standard deviation was 2.8–4.1% and the average recovery was 67.9% (n = 6).