晶种诱导Nonasil(HMI)的合成

以不同分子筛(Nonasil, MCM-22或MCM-49)为晶种, 在水热条件下以六亚甲基亚胺(HMI)为模板剂, 对纯硅沸石Nonasil(HMI)的合成进行了研究. 并且对各种合成参数, 包括晶种类型、硅源、晶化温度和Na+浓度等对Nonasil(HMI)合成的影响进行了探讨. 发现在适量的Na+存在条件下, 晶种的引入大大缩短了晶化时间; 不同类型的晶种对晶化速度有不同程度的提高. 特别是用异类晶种(如MCM-22或MCM-49)能够合成高结晶度的Nonasil(HMI).     

超声老化对MCM-49分子筛合成的影响

 以六亚甲基亚胺为模板剂,在静态水热合成条件下,考察了超声老化对MCM-49分子筛合成的影响. 结果表明,凝胶经超声老化处理后,即使使用比表面积小的硅源(硅胶或白碳黑)也能合成出不含杂晶且结晶良好的MCM-49分子筛. 超声老化处理缩短了MCM-49分子筛的晶化时间,扩大了分子筛的晶化范围,同时降低了模板剂的用量. 合成的MCM-49分子筛结晶度高,颗粒度小.     

MCM-22分子筛的静态合成与条件优化

在添加晶种条件下,MCM-22的静态合成速度大大加快,晶化时间可以缩短为72h.在用XRD、IR、TEM等手段对产品物相进行分析和表征的同时,考察并比较了晶种添加、模板剂用量和碱量对分子筛合成的影响.     

分子筛合成中六亚甲基亚胺与环己胺二元胺的模板作用

 以固体硅胶为硅源考察了六亚甲基亚胺(HMI)和环己胺(CHA)二元胺模板剂对分子筛合成产物的影响. XRD测试结果表明,当晶化温度为160 ℃,晶化时间为84 h, SiO2/Al2O3摩尔比为30, Na2O∶H2O∶(HMI+CHA)∶SiO2摩尔比为0.11∶45∶0.35∶1时,即使HMI仅占二元胺模板剂的25%(摩尔分数),所得分子筛仍为MCM-22; 其它条件相同时,以单纯CHA为模板剂得到的是ZSM-35分子筛. 用13C MAS NMR研究了HMI和CHA的状态,结果表明在单一HMI合成体系中,HMI既起MCM-22结构导向作用,又经质子化后起稳定骨架的作用; 而在HMI和CHA二元胺体系中,HMI主要起结构导向作用,CHA则填充在MCM-22层间十元环中稳定骨架.     

MCM-22分子筛的合成及其性质研究

以己内酰胺催化加氢得到的有机混合物水溶液(OMS)为模板剂合成了纯MCM-22分子筛，考察了晶化条件对合成产物的影响。采用XRD、SEM和NH3-TPD对所合成MCM-22分子筛的性质进行了研究。结果表明，原料碱度是影响合成产物的重要因素，合成纯MCM-22的硅铝比范围不大，同时原料中水含量对合成产物的影响也不容忽视；改变硅铝比及水蒸气处理可以调节MCM-22分子筛的酸性。     

凝胶硅铝比对合成MCM-22,UTM-1和Kenyaite的影响

 以白碳黑为硅源,偏铝酸钠为铝源,六亚甲基亚胺(HMI)为结构导向剂,采用动态水热法合成了MCM-22,UTM-1和kenyaite,并考察了硅铝比对产物晶相的影响. 结果表明, 配料硅铝比是影响产物晶相的重要因素. n(SiO2)/n(Al2O3)=30～50时,晶化产物为MCM-22; n(SiO2)/n(Al2O3)=71～190时,晶化产物为MCM-22与kenyaite的混合物,且随着硅铝比的增大,MCM-22的含量逐渐减少而kenyaite的含量逐渐增加; n(SiO2)/n(Al2O3)=228～609时,晶化产物为八元环结构的UTM-1; 不含铝源时,晶化产物为kenyaite. 就合成MCM-22和UTM-1而言,凝胶中的铝是必不可少的. 上述几种晶化产物均呈片状,可以通过扫描电镜加以区分.     

以离子液体为模板剂合成MCM-41的研究——不同扩孔剂对介孔分子筛MCM-41孔径结构的影响

以离子液体为模板剂, 正硅酸乙酯为硅源, 研究了扩孔剂三甲苯, 癸烷, 以及三甲苯与癸烷1∶1的混合物对介孔分子筛MCM-41结构的影响, 采用XRD以及氮吸附-脱附分析技术对合成的介孔分子筛MCM-41进行了表征.结果表明: 三种扩孔剂中以三甲苯与癸烷1∶1的混合物效果最优, MCM-41的孔径可达到4.5 nm, 并且可以提高介孔分子筛的比表面积与结晶度.扩孔剂的最佳添加量为: 扩孔剂与模板剂之比等于1.0;最佳晶化温度120 ℃.     

模板剂对全硅MCM-41介孔分子筛结构的影响

分别采用十六烷基三甲基溴化铵和十六烷基三乙基溴化铵作为模板剂,硅溶胶为硅源,用水热晶化法在碱性（NaOH）介质中合成了MCM-41介孔分子筛样品.通过XRD、N2吸附-脱附、TG-DTA、IR等测试手段对这两种样品进行了对比表征分析.考察了两种不同模板剂对其晶体结构、比表面及孔径大小的影响.实验结果表明,相对于十六烷基三甲基溴化铵做模板剂,采用大头基的十六烷基三乙基溴化铵可以合成较大孔径和孔容（分别为4.72 nm和1.14 cm3•g-1）的MCM-41介孔分子筛,而且具有较窄的孔径分布,因此对于合成大孔径的介孔分子筛MCM-41,十六烷基三乙基溴化铵是一种很好的模板剂.     

以十六烷基三甲基溴化铵为模板剂合成MCM-41/ZSM-5复合分子筛的研究

采用阳离子表面活性剂十六烷基三甲基溴化铵(CTAB)为模板剂、以ZSM-5为晶种,在水热晶化条件下合成了同时具有微孔和介孔的MCM-41/ZSM-5复合分子筛;并考察了陈化温度、陈化时间、晶化时间及模板剂用量等条件对合成复合分子筛的影响.通过X射线衍射、扫描电镜、高分辨率透射电镜、红外光谱及N2静态吸附法等手段对合成样...     

合成高产率分子筛MCM-48

以十六烷基三甲基溴化铵（CTAB）和Triton X-100（TX-100）混合表面活性剂为模板剂,正硅酸乙酯（TEOS）为硅源,采用水热法合成了MCM-48分子筛.实验中发现,晶化3 d后用醋酸调节溶液pH值的方法可有效提高MCM-48分子筛的产率；同时采用混合表面活性剂使模板剂的利用效率达到了6.0 TEOS/1.0 Surf (摩尔比）,并通过XRD、N2-吸附/脱附和TG-DSC等测试手段对产物的结构性能进行了表征.     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

恶臭嗅辨实验室建设探讨

针对恶臭测试的环境影响问题,提出了解决的实例方案,并对方案的要点及优缺点进行讨论,此方案在实际操作中具有较好的效果。     

Investigation of Kinetics of Solid-Phase Synthesis of Lithium Orthosilicate

The kinetics of the interaction between lithium carbonate and silica with various degrees of dispersion was investigated by TG and DTA methods. It was found that the utilization of pyrogenic silica with a specific surface area of about 300 m²g^-1 instead of aerosil with one of 175 m²g^-1 leads to an increase of the reaction rate between lithium carbonate and silica, which depends on the formation and growth of lithium orthosilicate crystals in the first stage, and is conditioned by the diffusion of lithium and oxygen ions through the lithium orthosilicate layer formed at temperatures above 800 K. This supposition is supported by the kinetic analysis results obtained with the use of the different models. The optimal regime of heating is recommended. This revised version was published online in July 2006 with corrections to the Cover Date.     

小环化合物中饱和碳质子化学位移的计算

小环化合物由于其张力、构型、构象和各向异性效应等原因,环碳上质子化学位移缺乏规律性,难以预测,对此作者曾提出一种近似算法。本文根据303种小环化合物中饱和碳质子的化学位移实验数据,将适于计算这类质子化学位移的公式表述为:     

解决能源问题的新途径--光解水制氢的研究

面对日益枯竭的能源危机,氢能是一种洁净、最有前景的替代能源。目前在各种制氢的方法中光催化分解水制氢的研究最多,光解水过程中催化剂最关键,本文对利用太阳能光解水的途径、提高光催化反应效率以及光催化剂的开发研究进行了综述。