载钛羟基磷灰石光催化降解内分泌干扰物双酚A（英文）

对载钛羟基磷灰石(TiHAP)进行了透射电镜、X射线衍射、紫外-可见光谱和Zeta电位表征,并应用液相色谱-质谱技术对比了TiHAP和P25 TiO2对环境内分泌干扰物双酚A(BPA)的吸附和光催化降解性能,探讨了富里酸和Fe3+对TiHAP薄膜光催化性能的影响.结果表明,TiHAP和TiO2粉体对BPA的吸附符合Langmuir吸附等温方程,且前者吸附性能更大.TiHAP薄膜光催化降解BPA的性能优于TiO2薄膜;富里酸和Fe3+对TiHAP和TiO2薄膜光催化性能的影响趋势不同,从能带结构、电子转移和吸光性等角度分析了性能不同的原因.本结果可以为应用TiHAP降解环境内分泌干扰物提供依据.     

模板法制备的Fe3+/TiO2中空纳米纤维的光催化性能

以棉花纤维为模板,利用浸渍-热转化两步法制备了Fe³⁺掺杂的二氧化钛(Fe³⁺/TiO₂)中空纳米纤维光催化材料,并利用扫描电镜(SEM)、X射线衍射(XRD)、紫外-可见光谱(UV-Vis)和ζ电位等技术对其形貌、结构、光吸收特性及其表面状态等进行了表征。以亚甲基蓝(methylene blue,MB)溶液的脱色降解为模型反应,考察了煅烧温度与时间对Fe³⁺/TiO₂中空纳米纤维光催化性能的影响。结果表明：利用该法可以制得棉花纤维形貌的Fe³⁺/TiO₂中空纳米结构材料;所得材料的催化性能除与材料的尺寸、相结构有关外,还与表面荷电性质有关,表面荷电量越高、表面结构缺陷越多、表面活性位越多,催化活性越高。500 ℃下煅烧2 h所得材料表面长有大量的粒子(平均尺寸为12 nm),其中TiO₂为锐钛矿结构,表面荷负电荷量最高,催化性能最好,如在太阳光下,2 h可使MB溶液的脱色降解率达93%,6 h完全脱色,而在纯TiO₂中空纤维材料上约为70%;该材料还具有良好的催化稳定性能,重复使用5次仍可使MB溶液的脱色降解率保持在90%以上,且该催化剂材料易于离心分离去除。     

RE/TiO2光催化剂的谱学特性与气相光催化性能的研究

采用改进的sol-gel法和浸渍法制备了TiO₂掺杂稀土离子La³⁺、Y³⁺、Gd³⁺、Er³⁺、Nd³⁺、Pr³⁺的RE/TiO₂光催化剂,运用FTIR、XRD、TEM、低温氮吸附/脱附、TG/DTA、UV-Vis DRS、表面光电压谱(SPS)等进行表征,以气相光催化降解乙烯、溴代甲烷作为探针反应,阐明了RE/TiO₂光催化剂的谱学特性与气相光催化性能的关系。结果显示,稀土离子掺杂后,TiO₂的锐钛矿含量增加,比表面积增大,粒径变小,吸收边发生蓝移,表面光电压的响应阈值增大,此外,Pr³⁺除外的其它稀土离子掺杂的TiO₂的表面光电压信号增强;光催化降解实验表明,与纯TiO₂相比,La³⁺、Y³⁺、Gd³⁺、Er³⁺、Nd³⁺掺杂TiO₂样品上乙烯、溴代甲烷的光催化活性均有不同程度的增强,而且表现出较强的矿化能力。但是,掺杂Pr³⁺的TiO₂的光催化性能降低恰好对应较弱的表面光电压信号。所以,本文认为提高光生电子-空穴对的分离效率是改善光催化性能的关键因素。     

磁载光催化剂Fe3O4/C/TiO2的制备及对三氯苯酚的降解

以FeCl₃为铁源, 葡萄糖为碳源, 钛酸四丁酯为钛源, 采用水热法制备了磁载光催化剂Fe₃O₄/C/TiO₂, 用TEM、EDX、VSM、XRD和IR对Fe₃O₄/C/TiO₂的粒径、形貌和物相等进行了表征。研究了该催化剂对三氯苯酚的降解性能, 探讨了其重复使用的可能性, 用荧光光谱法推测了可能的反应机理。结果表明该材料结合了光催化与可再生的优点, 1 g·L^-1 Fe₃O₄/C/TiO₂在18 W紫外灯下, 50 min内可将三氯苯酚降解97.9%以上, 6次循环使用后降解率仍保持在95.1%, 降解过程中有羟基自由基生成。     

原位红外光谱法研究La/TiO2对有机污染物的光催化降解

本工作采用改进的溶胶-凝胶法和浸渍法制备了TiO₂掺杂稀土离子La³⁺的La/TiO₂光催化剂，运用XRD、N₂吸附脱附、紫外可见漫反射光谱(DRS)、表面光电压谱(SPS)等手段进行表征，同时利用原位红外技术考察了La/TiO₂样品光催化降解乙烯、丙酮、苯的气-固相光催化氧化反应，对其光催化降解有机污染物的过程进行了研究。结果表明，TiO₂经适量La³⁺掺杂后，锐钛矿晶型的含量增加，晶粒度减小，比表面积增大，禁带宽度增加，表面光电压信号增强，光生电子-空穴对有效分离；La/TiO₂样品对乙烯、丙酮、苯的光催化性能与纯TiO₂相比均有不同程度的改善，乙烯可以被光催化氧化完全矿化生成CO₂，而丙酮被光催化氧化可能生成中间产物丙酸，苯被光催化氧化可能生成中间产物苯酚和苯醌。     

水热法制备具有高光催化活性的镧掺杂二氧化钛纳米晶

采用水热法合成钛酸钾(K₂Ti₈O₁₇)纳米棒,并将它作为前驱体水热转晶合成TiO₂纳米晶,同时通过在水热体系中引入稀土元素La³⁺实现对TiO₂的La掺杂.考察了不同条件下钛酸盐向TiO₂的转晶过程,发现水热溶液的pH值、温度以及预处理步骤对转晶过程有很大的影响.利用X射线衍射以及透射电子显微镜对样品的晶相和形貌进行了表征.利用电感耦合等离子体原子发射光谱测量了所合成的La掺杂TiO₂样品中的La含量.通过在紫外光下降解甲基橙(MO,10mg/L)测试了La掺杂TiO₂样品的光催化性能.结果表明La掺杂后TiO₂的光催化活性大大提高.在0.15mol/LLa³⁺浓度下180oC水热合成的La掺杂TiO₂样品显示了最佳的光催化活性.其对MO的光催化降解反应常数高达0.11min^-1,大约是空白TiO₂样品的9.20倍,P25TiO₂的3.69倍.     

Ti3+自掺杂的TiO2(A)/TiO2(R)/In2O3纳米异质结的制备与可见光催化性能

以TiCl₃和InCl₃为Ti源和In源,在不使用还原剂的条件下,首先通过液相沉淀反应制备前驱体沉淀,然后采用后续水热处理制备Ti³⁺自掺杂的TiO₂(A)/TiO₂(R)/In₂O₃纳米异质结,考察了水热处理温度对材料结构和性能的影响。利用X射线衍射、透射电子显微镜、X射线光电子能谱和紫外-可见漫反射光谱对样品进行表征。分别以罗丹明B和苯酚溶液为模拟废水评价了样品的可见光催化降解性能。结果表明,与纯的TiO₂、In₂O₃以及Ti³⁺自掺杂的TiO₂相比,Ti³⁺自掺杂的TiO₂(A)/TiO₂(R)/In₂O₃纳米异质结在可见光区有明显的吸收,并具有良好的可见光催化降解性能,200℃下水热处理24 h所得样品光催化降解罗丹明B的反应速率常数(0.0444 min^-1)分别是纯TiO₂和In₂O₃的17.76倍和8.71倍。瞬态光电流时间响应结果表明样品的光催化性能主要来源于TiO₂(A)/TiO₂(R)/In₂O₃纳米异质结导致的提高的光生电子和空穴分离效率。     

TiO2/Gd2O3纳米粉体的制备、表征及光催化活性

利用酸催化的溶胶-凝胶法制备了纯TiO₂和Gd³⁺(0.5wt%)掺杂的TiO₂纳米粉体，采用XRD、BET、XPS、紫外-可见漫反射谱(DRS)和表面光电压谱(SPS)等技术进行了表征；以亚甲基蓝(MB)的光催化降解为探针反应，评价了其光催化活性；探讨了Gd³⁺掺杂对TiO₂纳米粉体的光催化活性的影响机制。结果表明，TiO₂/Gd₂O₃纳米粒子对MB溶液的光催化活性提高到纯TiO₂的1.5倍。掺杂Gd³⁺可以强烈抑制TiO₂由锐钛矿相向金红石相的转变；阻碍TiO₂晶粒的生长；提高高温组织稳定性，改善粉体的表面织构特性；形成光生电子的浅势捕获陷阱，抑制e^-/h⁺复合，这些因素共同作用最终导致TiO₂/Gd₂O₃纳米粉体的光催化活性明显提高。XPS分析结果证实，掺杂Gd³⁺导致粉体的表面羟基含量降低。由于产生了量子尺寸效应，复合粉体的紫外吸收带边蓝移，光的吸收能力略有降低。     

一锅法制备S型异质结光催化剂Fe2O3/Fe2TiO5及其高效降解有机污染物性能

首次采用简单的一锅法制备了Fe₂O₃/Fe₂TiO₅异质结纳米材料。构建S型异质结后,与纯的Fe₂O₃和Fe₂TiO₅相比,Fe₂O₃/Fe₂TiO₅复合材料表现出更高的光催化降解速率和效率。经过2.5 h的光照后,Fe₂O₃/Fe₂TiO₅可以降解接近100%的亚甲基蓝（MB）。在Fe₂O₃/Fe₂TiO₅复合材料中,Fe₂O₃和Fe₂TiO₅之间形成了内建电场,可以促进光生电子-空穴对的分离。因此,具有更高能量的Fe₂TiO₅导带中的电子和具有更高能量的Fe₂O₃价带中的空穴可以得到有效的保留,从而使它们更加有效地扩散到催化剂表面,并参加降解反应。此外,Fe₂O₃/Fe₂TiO₅复合材料具有很好的光催化稳定性。     

Fe2BiTaO7纳米催化剂的组织结构及光催化性能

用固相反应合成法合成了光催化剂Fe₂BiTaO₇,通过XRD、SEM、TEM、紫外-可见漫反射等表征方法对其组织结构及光催化性能进行了研究.结果表明Fe₂BiTaO₇为立方晶系烧绿石结构,空间群为Fd₃m,禁带宽度为1.72eV.通过比较Fe₂BiTaO₇、P₂₅TiO₂、掺氮TiO₂和Bi₂InTaO₇的可见光光催化降解罗丹明B,发现Fe₂BiTaO₇降解效果及催化活性均高于其它催化剂,并且Fe₂BiTaO₇降解罗丹明B效率是掺氮二氧化钛的1.5倍.Fe₂BiTaO₇降解罗丹明B的曲线符合一级动力学,一级动力学常数为0.02293 min^-1.研究了罗丹明B可能的降解路径和Fe₂BiTaO₇在可见光下降解苯酚的效果.Fe₂BiTaO₇(可见光)光催化剂系统适用于纺织工业废水处理.     

Photocatalytic degradation of dimethyl phthalate ester using novel hydrophobic TiO2 pillared montmorillonite photocatalyst

TiO₂ pillared montmorillonites were prepared by introducing Ti⁴⁺ into a layer of montmorillonite modified with or without cetyltrimethylammonium bromide. The components and texture of the prepared composites were characterized by thermogravimetric analysis, X-ray powder diffraction and scanning electron misroscopy. The adsorption and photocatalytic degradation performance of a model environmental endocrine disruptor, dimethyl phthalate ester, were investigated using this newly prepared hydrophobic TiO₂ pillared montmorillonite photocatalyst. The adsorption of dimethyl phthalate ester from water varied from 9% to 28% on the prepared hydrophobic photocatalyst. Although the experimental results showed that the photocatalytic activity of the hydrophobic photocatalyst was slightly lower than that of hydrophilic one, electron spin resonance verified that hydroxyl radicals were also generated in hydrophobic TiO₂ pillared montmorillonite photocatalyst under UV irradiation. To elucidate the decomposition mechanism of dimethyl phthalate ester, 12 main photocatalytic intermediates were identified during the photocatalytic degradation process, and a plausible degradation mechanism was also proposed.     

Preparation of diatomite–TiO<Subscript>2</Subscript> composite for photodegradation of bisphenol-A in water

To enhance the photodegradation performance of pure titanium dioxide (TiO₂), diatomite was used as a porous carrier to immobilize TiO₂ powders using calcination method. The photodegradation of bisphenol-A (BPA; 4,4′-isopropylidenediphenol), which has been listed as one of endocrine disrupting chemicals, was carried out in a batch suspension reactor using pure TiO₂ powders and diatomite–TiO₂ composites, respectively. Under the controlled conditions, the photocatalytic efficiencies of the BPA degradation by the diatomite–TiO₂ composites can be found to be higher than those by pure TiO₂ powders. This result should be attributable to the accessibility of the BPA molecules to the surface of TiO₂ particle in the modified photocatalysts, showing that the enrichment of the organic solute enhanced the rate of photodegradation on the diatomite–TiO₂ composite. However, the photodegradation efficiency was not dependent on the pore properties of these TiO₂ photocatalysts. The experimental results further indicated that the photodegradation kinetics for the destruction of BPA in water followed the first-order model well. The apparent first-order reaction constants (k _obs), thus obtained from the fittings of the model, were in line with the destruction-removal efficiencies of BPA in all the photocatalytic experiments.     

Microstructure of SiO<Subscript>2</Subscript>/TiO<Subscript>2</Subscript> hybrid electrospun nanofibers and their application in dye degradation

SiO₂/TiO₂ hybrid nanofibers were prepared by electrospinning and applied for photocatalytic degradation of methylene blue (MB). The phase structure, specific surface area, and surface morphologies of the SiO₂/TiO₂ hybrid nanofibers were characterized through thermogravimetry (TG), X-ray diffraction (XRD) analysis, Brunauer–Emmett–Teller (BET) analysis, scanning electron microscopy (SEM), etc. XRD measurements indicated that doping of silica into TiO₂ nanofibers can delay the phase transition from anatase to rutile and decrease the grain size. SEM and BET characterization proved that silica doping can remarkably enhance the porosity of the SiO₂/TiO₂ hybrid nanofibers. The MB adsorption capacity and photocatalytic activity of the SiO₂/TiO₂ hybrid nanofibers were distinguished experimentally. It was found that, although increased silica doping content could enhance the MB adsorption capacity, the intrinsic photocatalytic activity gradually dropped. The SiO₂ (10 %)/TiO₂ composite nanofibers exhibited the highest MB degradation rate, being superior to SiO₂ (20 %)/TiO₂ or pure TiO₂.     

Evaluating the efficiency of the GO‐Fe3O4/TiO2 mesoporous photocatalyst for degradation of chlorpyrifos pesticide under visible light irradiation

In this work, the photocatalytic activity of the synthesized graphene oxide (GO)‐Fe₃O₄/TiO₂ mesoporous photocatalysts was evaluated using chlorpyrifos (CP) as a contaminant. The nano‐photocatalyst was characterized by X‐ray diffraction, field emission scanning electron microscopy with energy‐dispersive X‐ray spectroscopy, transmission electron microscopy, and specific surface area by the Brunauer–Emmett–Teller method. Using visible light, the GO‐Fe₃O₄/TiO₂ mesoporous photocatalyst was investigated on the degradation of CP pesticide. The GO‐Fe₃O₄/TiO₂ photocatalyst displayed a good photocatalytic activity, which was achieving 97% of CP degradation after 60 min. Finally, experiments were performed to evaluate GO‐Fe₃O₄/TiO₂ mesoporous nanocatalyst activity on repeated applications; after several uses, its photocatalytic activity was retained, which indicated stability.     

Photocatalytic degradation of methylene blue on Fe3+-doped TiO2 nanoparticles under visible light irradiation

Fe³⁺-doped TiO₂ composite nanoparticles with different doping amounts were successfully synthesized using sol-gel method and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and ultravioletvisible spectroscopy (UV-Vis) diffuse reflectance spectra (DRS). The photocatalytic degradation of methylene blue was used as a model reaction to evaluate the photocatalytic activity of Fe³⁺/TiO₂ nanoparticles under visible light irradiation. The influence of doping amount of Fe³⁺ (ω: 0.00%–3.00%) on photocatalytic activities of TiO₂ was investigated. Results show that the size of Fe³⁺/TiO₂ particles decreases with the increase of the amount of Fe³⁺ and their absorption spectra are broaden and absorption intensities are also increased. Doping Fe³⁺ can control the conversion of TiO₂ from anatase to rutile. The doping amount of Fe³⁺ remarkably affects the activity of the catalyst, and the optimum efficiency occurs at about the doping amount of 0.3%. The appropriate doping of Fe³⁺ can markedly increase the catalytic activity of TiO₂ under visible light irradiation. __________ Translated from Journal of Northwest Normal University (Natural Science), 2006, 42(6): 55–56 [译自: 西北师范大学学报(自然科学版)]     

Photocatalytic Activity of High Aspect Ratio TiO2 Nanorods

In this article, TiO₂ nanorods (aspect ratio >20) were prepared through a polyol process and doped with metal ions (Cu²⁺, Ni²⁺, Fe³⁺, and Cr³⁺). Compared with TiO₂ nanoparticles, the TiO₂ nanorods displayed relatively higher photocatalytic activity for the degradation of copper sulfophthalocyanine. Moreover, the photocatalytic activity was greatly enhanced when the metal ions were doped in the TiO₂ nanorods.     

Fe2BiTaO7纳米催化剂的组织结构及光催化性能

用固相反应合成法合成了光催化剂Fe2BiTaO7,通过XRD、SEM、TEM、紫外-可见漫反射等表征方法对其组织结构及光催化性能进行了研究。结果表明Fe2BiTaO7为立方晶系烧绿石结构,空间群为Fd3m,禁带宽度为1.72 e V。通过比较Fe2BiTaO7、P25TiO2、掺氮Ti O2和Bi2In Ta O7的可见光光催化降解罗丹明B,发现Fe2BiTaO7降解效果及催化活性均高于其它催化剂,并且Fe2BiTaO7降解罗丹明B效率是掺氮二氧化钛的1.5倍。Fe2BiTaO7降解罗丹明B的曲线符合一级动力学,一级动力学常数为0.022 93 min-1。研究了罗丹明B可能的降解路径和Fe2BiTaO7在可见光下降解苯酚的效果。Fe2BiTaO7(可见光)光催化剂系统适用于纺织工业废水处理。     

Visible light photocatalytic activity and Photoelectrochemical property of Fe-doped TiO<Subscript>2</Subscript> hollow spheres by sol–gel method

Fe-doped TiO₂ hollow spheres (Fe-THs) were synthesized by sol–gel process using carbon spheres as templates. The prepared samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), UV–vis diffuse reflectance spectrum (DRS), N₂ adsorption–desorption isotherms, Electron paramagnetic resonance (EPR) spectroscopy and Photoluminescence emission spectroscopy (PL). UV–vis spectra showed that Fe³⁺ doping could extend the absorption edge to the visible region. EPR spectra showed that Fe³⁺ was incorporated into the crystal lattice of TiO₂, which could inhibit the recombination of photo-induced electron–hole pairs and improve the photocatalytic activity. The photocatalytic activities of the prepared samples were evaluated for the degradation of dye Reactive Brilliant Red X-3B (C.I. reactive red 2) under visible light irradiation. The results indicated that Fe³⁺ doping sample showed the highest photocatalytic activity with an optimal doping concentration of 0.50 wt%. The recycle ability of the Fe-THs was also investigated. After 5 cycles, the degradation rate was still higher than 90%, decreased by only 6.36% compared to the first cycle. Moreover, in order to characterize the electron-transferring efficiency in the process of photocatalysis reaction, a photocurrent-time spectrum was examined by anodic photocurrent response.     

Controlled synthesis of novel PbBiO<Subscript>2</Subscript>I microsphere structure towards photocatalytic degradation of bisphenol A

Novel visible-light-driven PbBiO₂I materials have been successfully synthesized through a one-pot ethylene glycol assisted solvothermal process in the presence of 1-hexyl-3-methylimidazolium iodide ([Hmim]I). The morphologies, compositions and properties of the PbBiO₂I materials were investigated by XRD, XPS, SEM, TEM, DRS and nitrogen adsorption–desorption isotherms. The results of SEM and TEM indicated that the as-prepared PbBiO₂I samples were microspheres with a diameter of about 1.5 μm assembled by nanosheets. The photocatalytic performance of the prepared PbBiO₂I materials was determined by colorless endocrine disrupting chemical bisphenol A (BPA) and antibiotic ciprofloxacin (CIP). PbBiO₂I materials have a very good visible light response with band gap of 1.98 eV, thus result in better photocatalytic degradation activity. Under the visible light irradiation for 3 h, about 72.5% of the BPA could be removed by PbBiO₂I microspheres. The main active species during the photodegradation process were determined to be superoxide radicals and holes.