Simple apparatus for size fractionation of particles by hydrodynamic elutriation

A method is described for separating column packing materials into series of products of any desired narrow particle size distributions.     

Thermal characterization of lignocellulosic residue from different sugarcanes

Bagasse samples from four different sugarcane were directly collected as the residues of milling in a processing plant. The samples were dried at 105 °C, compressed to small granules and then their TG/DTA and DSC curves in synthetic air were recorded. Similar thermogravimetric curves were obtained for the different samples and they exhibited four mass loss steps. However, the analysis of the exotherm DSC peaks showed that the oxidation of the organic matter resulted different enthalpy values (ΔH/kJ g⁻¹).     

Crystallizability of ethylene homopolymers by crystallization analysis fractionation

The effect of molecular weight and long‐chain branching on the crystallization analysis fractionation (CRYSTAF) of ethylene homopolymers was investigated. Several ethylene homopolymers were prepared with different molecular weights and levels of long‐chain branching to isolate these effects from the dominant effect of comonomer content on crystallizability measured by CRYSTAF. Molecular weight effects might be significant for samples with number‐average molecular weights below 5000, but this effect can be corrected if terminal methyl groups are taken into account. Long‐chain branching has only a very small effect on the CRYSTAF profile of the samples investigated in this study. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1616–1628, 2001     

Crystallization analysis fractionation

Crystallization analysis fractionation (CRYSTAF) is an analytical technique for determining the distribution of chain crystallizabilities of semicrystalline polymers. After only approximately a decade since it was developed, CRYSTAF has become one of the most important characterization techniques in polyolefin characterization laboratories because it provides fast and crucial information required for the proper understanding of polymerization mechanisms and structure–property relationships. In the polyolefin industry, it has been established as an indispensable tool for product development and product quality monitoring. This highlight article covers basic operation procedures, applications, and theoretical aspects of polymer fractionation with CRYSTAF. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1557–1570, 2005     

Chain regularity of isotactic polypropylene determined by different thermal fractionation methods

The chain regularity of isotactic polypropylene (iPP) homopolymer and random copolymers was characterized by different thermal fractionation methods in this study. Different stepwise temperature programs were applied in a calorimeter (DSC), in order to develop a method which is significantly faster than stepwise isothermal segregation technique (SIST) and provides reliable information about the chain regularity of iPP. Our studies prove that self-seeding accelerates the crystallization process during annealing in SSA–DSC experiments (successive self-nucleation and annealing). Consequently, the time of isothermal steps can be shortened significantly in the SSA–DSC method. On the other hand, we found that step time should not be too short if the goal of the measurement is the determination of average chain regularity. Our results clearly indicate that both the experimental conditions and the evaluation technique influence the obtained results. A standard experimental procedure is proposed for reliably determining the average chain regularity of iPP. The length of the SSA–DSC temperature program developed in this study is much shorter compared to that of the conventional SIST measurements used recently for such experiments. The proposed SSA–DSC program makes the reliable characterization of a large number of samples on an acceptable timescale possible.     

Three-way multivariate analysis of metal fractionation results from sediment samples obtained by different sequential extraction procedures and ICP-OES

Three typical schemes for metal fractionation were applied to analyse coastal surface sediment samples from Bahía Blanca estuary, where an important industrial emplacement is located. Also, three certified reference materials for total metal concentrations were analysed. The studied metals were cadmium, chromium, copper, lead and zinc because of their hazardous potential and related abundance in the estuary. The concentration of metals was determined by inductively coupled plasma-optical emission spectrometry (ICP-OES). A three-way multivariate analysis was performed in order to obtain a better visualization of the experimental data. The extracted information was used to evaluate the equivalence among the results obtained by the three sequential extraction schemes. The data were analysed by parallel factor analysis (PARAFAC). PARAFAC models with two factors describe appropriately the data sets (explained variance about 54% and core consistency of 100%). The multivariate decomposition showed that the three applied schemes are able to describe equally well the behaviour of the metals in the different sediment fractions.     

Upgrading of paper grade pulps to dissolving pulps by nitren extraction: yields,molecular and supramolecular structures of nitren extracted pulps

Different paper grade pulps were extracted with nitren in order to produce dissolving pulps and polymeric xylan. The yield and molecular structure of the extracted pulps were investigated by carbohydrate analysis and HPSEC combined with fluorescence labelling in order to additionally monitor the carbonyl and carboxyl group profiles of the pulps. The supramolecular structure of selected pulps were further studied by solid state ¹³C-CP/MAS-NMR and wide-angle X-ray scattering (WAXS). These supramolecular data of nitren extracted pulps were compared to samples extracted with NaOH and a conventional dissolving pulp in order to classify the properties of nitren extracted pulps. Nitren extraction results in selective xylan removal without noticeable degradation or oxidation of the cellulose fraction. The resulting dissolving pulps have high molar masses, a narrow molar mass distribution and the typical contents of carbonyl and carboxyl groups. The supramolecular structure of cellulose is less affected by nitren compared to strong NaOH, and the resultant dissolving pulps still have the cellulose I structure. All laboratories are members of the European polysaccharide network of excellence EPNOE.     

13C CPMAS NMR investigations of cellulose polymorphs in different pulps

In order to obtain information about the crystallinity and polymorphs of cellulose, and the occurrence of hemicelluloses in pulp fibers, wood cellulose, bacterial cellulose, cotton linters, viscose, and celluloses in different pulps were investigated by solid state ¹³C CPMAS NMR spectroscopy. A mixed softwood kraft pulp and a dissolving-grade pulp were treated under strongly alkaline and acidic conditions and the effect on cellulose crystallinity was studied. The presence of different crystalline polymorphs of cellulose and the amounts of hemicelluloses are considered.     

Polymer analysis by fractionation with on-line light scattering detectors

Summary The classical method for the determination of the molecular weight distribution (MWD) curve of a polymer requires fractionation according to the molecular weight and prior calibration of the separator. It is shown that the use of a dual detection system which includes a molecular mass sensitive detector eliminates the need for prior calibration. The principles of operation of a low-angle light scattering photometer, working as such a detector, are presented, as well as the basic equations for determination of the MWD curve from the elution curve and of the average molecular weights. Then the performances of the light scattering photometer are discussed with special emphasis on the various sources of errors and unaccuracies in these determinations.     

Polyolefin analysis by single‐step crystallization fractionation

Temperature rising elution fractionation (TREF) fractionates polymer chains with respect to their crystallizability, independently of molecular weight effects. In order to achieve a good fractionation, TREF requires a time‐consuming polymer deposition step over an inert support before the elution step. A single‐step crystallization fractionation method has been developed recently,^1,2 Crystallization Analysis Fractionation (CRYSTAF), in which the chemical composition (or short chain branching) distribution of olefin copolymers can be measured by monitoring on‐line polymer concentration in solution at decreasing temperatures. For the present experimental investigation, a CRYSTAF‐prototype has been assembled and used to fractionate several linear low‐density polyethylene (LLDPE) samples. These results were compared to the ones measured by the commercial CRYSTAF apparatus from Polymer ChAR. Additionally, CRYSTAF results from Polymer ChAR were compared to analytical TREF results. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 539–552, 1999     

Separation of mitochondria by flow field-flow fractionation for proteomic analysis

Flow field-flow fractionation (FlFFF) has been utilized for size-based separation of rat liver mitochondria. Collected fractions of mitochondria of various sizes were examined by confocal microscopy, and mitochondria of each fraction were lysed and analyzed by two-dimensional polyacrylamide gel electrophoresis (2D-PAGE) for the comparison of protein patterns in differently sized mitochondria by densitometric measurements, and for protein characterization of some gel spots with nanoflow liquid chromatography-electrospray ionization-tandem mass spectrometry (nLC-ESI-MS-MS). FlFFF fractions of the mitochondria were also tryptically digested for shotgun proteomic characterization of mitochondrial proteins/peptides by nLC-ESI-MS-MS. Peak area (integrated ion counts) of some peptides extracted from LC-MS chromatograms were examined at different fractions for the quantitative comparison. Among 130 proteins, 105 unique proteins were found to be mitochodrial from the off-line combination of FlFFF and nLC-ESI-MS-MS analysis. It also showed that 23 proteins were found in all fractions but some proteins were found exclusively in certain fractions. Among 25 proteins listed from other subcellular species, seven proteins were known to exist in mitochondria as well as in other subcellular locations, which may support the possible translocation or multiple localizations of proteins among organelles. This study demonstrated effective use of FlFFF for the isolation and/or enrichment of intact mitochondria isolated from cells, as well as its potential use for the fractionation of other subcellular components in the framework of subcellular functional proteomics.     

Reactivity of dissolving pulps modified by TEMPO-mediated oxidation

The reactivity of dissolving pulps towards derivatization or dissolution is a crucial quality parameter and is mainly determined by the accessibility of the hydroxyl groups. When dissolving pulps are produced from paper-grade pulps by cold caustic extraction (CCE), their reactivity is often inferior as compared to commercial prehydrolysis kraft dissolving pulps. It was hypothesized that pulp reactivity can be enhanced by the introduction of small amounts of substituents to facilitate interchain accessibility. In this study, CCE-treated Eucalyptus globulus kraft paper pulp was subjected to TEMPO-mediated oxidation to initiate partial oxidation of the C₆-hydroxyl groups to carboxyl groups. The effect of this pulp modification on the reactivity towards xanthation and the subsequent dissolution in diluted aqueous alkali solution (viscose process) as well as the dissolution in complexing and non-complexing solvents, respectively, was thoroughly examined. The results revealed that the oxidized pulps rich in C₆-carboxylate groups impeded the xanthation reaction obviously because of the reduced availability of hydroxyl groups. When N-methylmorpholine-N-oxide monohydrate was used as a direct solvent, a very high content of C₆-carboxylate groups was found to reduce the solubility of the pulp fibers as less hydrogen bonds can be formed with NMMO·H₂O. In the case of dissolution in the complexing solvent cupriethylenediamine, the dissolution mechanism of cellulose was not deteriorated by the high content of C₆-carboxylate groups. Instead, the oxidation procedure increased the hydrophilic character and the swelling capacity of the outer cell wall layers allowed homogeneous dissolution.     

Flow field-flow fractionation for hydrodynamic diameter estimation of gold nanoparticles with various types of surface coatings

Analytical and Bioanalytical Chemistry - Flow field-flow fractionation (FlFFF) with inductively coupled plasma mass spectrometric (ICP-MS) detection was applied for estimating the hydrodynamic...     

Effect of operation parameters on temperature rising elution fractionation and crystallization analysis fractionation

Crystallization analysis fractionation and temperature rising elution fractionation are two techniques used to estimate the chemical composition distributions of semicrystalline copolymers. This study investigates the cooling rate and cocrystallization effects for both techniques with a series of ethylene/1‐olefin copolymers and their blends. Ideally, both techniques should operate in the vicinity of thermodynamic equilibrium so that crystallization kinetic effects are avoided. The results show that, in fact, crystallization kinetic effects play an important role at the typical cooling rate used with both techniques. Cocrystallization is significant when fast cooling rates are used. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1762–1778, 2003     

Size analysis of industrial carbon blacks by sedimentation and flow field-flow fractionation

Carbon black is one of the most useful particulate materials in the industrial field. Among the various physical properties of carbon black, size and size distribution are the most important properties to affect the quality of a final product. However, it is difficult to measure the exact particle size of carbon black since it suffers unavoidable interference from flocculation. In this study, the effects of various factors on the dispersion of industrial carbon blacks were investigated for the determination of size and size distribution of carbon black particles. Sedimentation and flow field-flow fractionations (FIFFF) were used to determine the size of carbon black, and their optimum analytical conditions were tested by changing surfactant, pH, ionic strength, and method of dispersion. The results showed that surfactant structure and its concentration played significant roles in dispersion stability. Carbon black was dispersed well with a nonionic surfactant with a pH of around 8 and an ionic strength of 0.003 M. The mean diameters measured from two types of FFF and photon correlation spectroscopy are in good agreement. This study demonstrates the potential of sedimentation and flow FFF for analyzing highly adsorptive industrial particles and guides for sample preparation.     

Bleachability and characterization by fourier transform infrared principal component analysis of acetosolv pulps obtained from sugarcane bagasse

Sugarcane bagasse Acetosolv pulps were bleached by xylanase and the pulps classified by using Fourier transform infrared (FTIR) spectroscopy and principal component analysis (PCA). Pulp was treated with xylanase for 4–8 h with stirring at 30°C. Some samples were further extracted with NaOH for 1 h at 65°C. FTIR spectra were recorded directly from the dried pulp samples by using the diffuse reflectance technique. Reduction in kappa number of 69% was obtained after sequence xylanase (4 h)-alkaline extraction. During bleaching the viscosity decreased only 12%. FTIR-PCA showed that the first three principal components (PCs) explained more than 90% of the total variance of the pulp spectra. PC2×PC1 plot showed that the points related to pulps from sequence xylanase (4 h)-alkaline extraction are different from the other. This group isenlarged by plotting PC3×PC1 or PC3×PC2 containing all pulps submitted to alkaline extraction. PC2 and PC3 are the principal factor for differentiation of the pulps. These PCs suffer influence of the ester bands (1740 and 1244 cm⁻¹). On the other hand, the pulps bleached only with xylanase could not be differentiated from the nonbleached pulps.     

Investigation of red blood cell fractionation by gravitational field-flow fractionation.

Gravitational field-flow fractionation is used for the separation of particles according to their sizes in the range 1-100 microns: larger particles elute before smaller ones. This phenomenon can be explained as a result of the steric exclusion of the particles from the vicinity of the channel walls, and/or hydrodynamic effects supposedly associated with the inertia of the liquid. The method was used for the investigation of red blood cells. The dependence of the retention ratio on the flow-rate, sample volume, concentration of blood and relaxation time was studied. Analysis of fifteen individual fractions by Coulter counter and reinjection of three other fractions were studied in order to verify fractionation of red blood cells.     

Surface characterization of unbleached kraft pulps by means of ESCA

The effect of digestion conditions (amount of effective alkali, digestion time) on the surface compositions of unbleached softwood (Pinus sylvestris) kraft pulp has been investigated by electron spectroscopy for chemical analysis (ESCA). The quantities monitored were the angular dependence of the total O/C ratio, the relative amounts of carbons in different states of oxidation and the adsorption of Al and Ca ions to the carboxyl groups in the surface. Examination of the angular dependence of ESCA intensities shows that the concentration of alkyl carbon is high in a very thin surface layer and that it decreases linearly with decreasing kappa number. The concentration of alkyl carbon is decreased by extraction of the fibres with dichloromethane, but the amount remaining in the surface after extraction still decreases linearly with decreasing kappa number (i.e. it decreases with increasing digestion time). It is suggested that the observed enrichment of alkyl carbon in the outermost surface layers most probably is due to reprecipitation of lignin. In pulp that has not been extracted, there is also strong enrichment of extractives in the surface. This amount increases with increasing effective alkali but is relatively independent of digestion time. ESCA analysis of the Al and Ca bound to the carboxyl groups shows that the amount depends on digestion time; the results are consistent with the notion that the reprecipitated lignin contains carboxyl groups.     

Mercury and trace element fractionation in Almaden soils by application of different sequential extraction procedures

A comparative evaluation of the mercury distribution in a soil sample from Almaden (Spain) has been performed by applying three different sequential extraction procedures, namely, modified BCR (three steps in sequence), Di Giulio–Ryan (four steps in sequence), and a specific SEP developed at CIEMAT (six steps in sequence). There were important differences in the mercury extraction results obtained by the three procedures according to the reagents applied and the sequence of their application. These findings highlight the difficulty of setting a universal SEP to obtain information on metal fractions of different mobility for any soil sample, as well as the requirement for knowledge about the mineralogical and chemical characteristics of the samples. The specific six-step CIEMAT sequential extraction procedure was applied to a soil profile (Ap, Ah, Bt1, and Bt2 horizons). The distribution of mercury and major, minor, and trace elements in the different fractions were determined. The results indicate that mercury is mainly released with 6 M HCl. The strong association of mercury with crystalline iron oxyhydroxides, present in all the horizons of the profile, and/or the solubility of some mercury compounds in such acid can explain this fact. Minor mercury is found in the fraction assigned to oxidizable matter and in the final insoluble residue (cinnabar).     

Thermal and dynamic mechanical thermal analysis of lignocellulosic material-filled polyethylene bio-composites

Thermal and rheological properties of plant-based natural filler-reinforced polyethylene bio-composites applying various filler loadings as well as the impacts of the different compatibilizers were investigated by means of differential scanning calorimetry and dynamic mechanical thermal analysis (DMTA). As lignocellulosic materials, such as rice-husk flour and wood flour, are eco-friendly biomaterials and a thermoplastic polymer, for example, high-density polyethylene, has good physico-mechanical and thermal properties, therefore their bio-composites can combine and utilize these two advantages at the same time. The temperature of the α-relaxation (T _α) slightly increased and melting temperatures (T _m) of the matrix polymer in the case of the studied bio-composites did not shift significantly as the filler loading changed, because the rigid interphase hinders the motion of polymer segments resulting in the increase in T _α and only weak interactions developed at the interface between the matrix polymer and the reinforcement in the case of non-compatibilized composites. However, compatibility between the reinforcement and the matrix polymer was enhanced by incorporating compatibilizers, which further improved stiffness. From the DMTA experiment, the reinforcements result in composite samples having higher storage modulus (E′) than the neat polymer sample, indicating that incorporating lignocellulosic filler increased their stiffness.