Determination of interfacial tension from crystallization and dissolution data: a comparison with other methods

Methods for the determination of interfacial tension between a solid and a liquid are reviewed including solubility/particle size, crystallization and dissolution kinetics. The use of solubility as a function of particle size, originally put forward by Ostwald and later corrected by Freundlich, may be unjustified for determining interfacial tension at solid-liquid interfaces. The interfacial tension values between solutions and sparingly soluble minerals such as hydroxyapatite, fluorapatite, brushite, octacalcium phosphate, calcium oxalate monohydrate, barium sulfate, calcium sulfate, calcite, and divalent metal fluorides are discussed. A comparison of these results is made with contact angle or wetting measurements. The interfacial tension values obtained from constant composition reaction kinetics are of the same order of magnitude as those determined using a contact angle method involving thin layer wicking techniques.     

Effects of solid-liquid interface on the interfacial tension measured by micropipet technique

Measurement of interfacial tension (IFT) using the micropipet technique involves the solid-liquid interface. At equilibrium, oil-water interfacial tension is determined from the interface curvature and the critical pressure, according to the Young-Laplace equation. This paper aims to examine the possible contribution of the solid-liquid interface on IFT measurement. Three different experimental configurations are used to examine the sought effect. The three configurations are straight, concentric, and tapered pipets with diameters ranging from 2.5 to 30 microm. For all three configurations, the critical pressure is found to depend only on the pipet diameter. However, when the Young-Laplace equation is applied to determine the IFT, a significant error was noticed at small pipet diameters. The IFT error was described by an exponential function whose asymptote approached the independently determined IFT value with a sufficiently large pipet diameter. The IFT error is anticipated to arise from the layerlike effect of an "ultrastructured" liquid near the solid surface. The solid-induced error in oil-water IFT is noted to fade away at lowered IFT by the addition of surfactant.     

Study on the Interfacial Tensions Between Oils and Alkylbenzene Sulfonate Gemini Surfactant Solutions

Interfacial tensions (IFT) of five alkylbenzene sulfonate Gemini surfactants Ia, Ib, Ic, Id, and Ie at different oils/water systems were measured by a spinning drop interfacial tensiometer. And critical micelle concentration (CMC), the interfacial tension at CMC (γ_CMC), maximum interfacial excess concentration (Γ _max) and the surface area per molecule (A_min) were calculated. The results indicated that the CMC values determined with interfacial tension method were lower than those determined with surface tension method. And γ_CMC for Ie is larger than that for Ia, Ib, Ic, and Id. In addition, the effects of temperature and hydrophobic chains on dynamic IFT were also studied. With the increment of temperature, dynamic IFT is easier to reach a stable value. However, with the increment of hydrophobic chains, dynamic IFT is more difficult to reach a stable value. Each Gemini surfactant produces a minimum IFT when measured against a different n-alkane.     

Study on the Mechanism of Asphaltenes Reducing Oil-Water Interfacial Tension

As high polar components of crude oil, asphaltenes play a significant role in reducing oil-water interfacial tension(IFT). In this paper, the effects of asphaltenes on reducing IFT in the presence of surfactant were compared, and the mechanism of asphaltenes reducing the IFT was studied by the dynamic interfacial tension(DIFT) equation. Whether asphaltenes were added to the oil or 2,5-dimethyl-4-(4-dodecyl) benzene sodium sulfonate(p-S14-4) was added to the water phase, either of all results in the IFT reducing and the IFT is related to the coverage and the mass of asphaltenes adsorption at the interface. In the presence of asphaltenes, the adsorption of the active substances to the interface is not entirely dependent on diffusion, and the process can be divided into three regions. Region I: the IFT rapidly reducing, this process is controlled by diffusion of surfactant; Region II: the IFT reducing slowly, resulted from the lower diffusion rate that is limited due to the aggregates formed by the interaction of asphaltene-asphaltene; Region III: the interaction of asphaltene-asphaltene is broken by the interaction of surfactant-asphaltene. The asphaltene aggregates are reduced and adsorbed rapidly at the interface. Furthermore, the results reveal that the asphaltenes concentration affects the coverage rate and adsorption at the interface.     

Anomalous temperature dependence of interfacial tension in water-hydrocarbon mixtures

An experimental study of the interfacial tension (IFT) as a function of temperature for three water-hydrocarbon mixtures is reported. The interfacial tension rises with increasing temperature for all mixtures studied, which contradicts the Antonov rule.     

高盐油藏下两性/阴离子表面活性剂协同获得油水超低界面张力

研究了在高盐油藏中, 利用两性/阴离子表面活性剂的协同效应获得油水超低界面张力的方法. 两性表面活性剂十六烷基磺基甜菜碱与高盐矿化水具有很好的相容性, 但在表面活性剂浓度为0.07%-0.39%(质量分数)范围内仅能使油水界面张力达到10^-2 mN·m^-1量级, 加入阴离子表面活性剂十二烷基硫酸钠后则可与原油达到超低界面张力. 通过探讨表面活性剂总浓度、金属离子浓度、复配比例对油水动态界面张力的影响, 发现两性/阴离子表面活性剂混合体系可以在高矿化度、低浓度和0.04%-0.37%的宽浓度范围下获得10^-5 mN·m^-1量级的超低界面张力, 并分析了两性/阴离子表面活性剂间协同获得超低界面张力的机制.     

Interfacial tension of solid materials against dense carbon dioxide

In the Young equation, only two of the four unknowns are measurable. They are the liquid interfacial tension sigma lv and the contact angle theta. To solve this equation, another correlation is required. In solving this equation, a better understanding of the magnitude of the solid interfacial tension sigma sv and the solid-liquid interfacial tension sigma sl is expected. The possibility of a theoretical estimation of the contact angle theta is sought as an alternative to the experimental method. In this paper, an attempt to calculate the solid interfacial tension sigma sv is reported. It is based on the intermolecular interaction which is mathematically described in the parameter Phi sl according to Good. The calculated sigma sv values for PTFE, steel, and glass surrounded by dense carbon dioxide are verified by comparing those values obtained from aqueous and ethanolic systems. Furthermore, the solid interfacial tension sigma sv is also used to forecast the water drop contact angle theta. The calculated values are compared with the experimental measured ones.     

New Prediction Model of Surface and Interfacial Energies Based on COSMO-UCE**

The nature and strength of intermolecular and surface forces are the key factors that influence the solvation, adhesion and wetting phenomena. The universal cohesive energy prediction equation based on conductor-like screening model (COSMO-UCE) was extended from like molecules (pure liquids) to unlike molecules (dissimilar liquids). A new molecular-thermodynamic model of interfacial tension (IFT) for liquid-liquid and solid-liquid systems was developed in this work, which can predict the surface free energy of solid materials and interfacial energy directly through cohesive energy calculations based on COSMO-UCE. The applications of this model in prediction of IFT for water-organic, solid (n-hexatriacontane, polytetrafluoroethylene (PTFE) and octadecyl-amine monolayer)-liquid systems have been verified extensively with successful results; which indicates that this is a straightforward and reliable model of surface and interfacial energies through predicting intermolecular interactions based on merely molecular structure (profiles of surface segment charge density), the dimensionless wetting coefficient R_A/C can characterize the wetting behavior (poor adhesive (non-wetting), wetting, spreading) of liquids on the surface of solid materials very well.     

Dynamic Interfacial Tension Behavior of Water/Oil Systems Containing In situ-Formed Surfactants

Time-dependent interfacial tension (IFT) has been investigated for an interfacially reactive immiscible system composed of model-acidified oil and alkaline water. The acidified oil was composed of either lauric acid or linoleic acid dissolved in n-dodecane. Drop volume tensiometry was employed to measure the interfacial tension between the two phases. In the case of lauric acid, the IFT value was found to decrease sharply with increasing alkali concentration, even at low drop formation times. In the case of linoleic acid, the IFT decrease with the drop formation time was more gradual, especially at low alkali concentration. The rate of formation of the interfacial area was also found to be dependent on alkali concentration.     

CMC系列高分子表面活性剂与原油超低界面张力形成机理的研究

采用动态激光光散射及环境扫描电镜研究了羧甲基纤维素系列高分子表面活性剂与大庆原油形成超低界面张力的机理.结果表明,CMC系列高分子表面活性剂具有与低分子量表面活性剂相比拟的表/界面活性,其水溶液的表面张力可达2835mN/m,界面张力达到10^-110mN/m.碱的加入可显著降低高分子表面活性剂与原油的界面张力,在适当条件下界面张力达到超低值(10^-3mN/m),可望作为三次采油的驱油剂.等效烷烃模型研究表明,用碱与原油酸性组分的作用来解释碱能使界面张力下降至超低值的传统观点是不完善的,加入碱能使高分子表面活性剂胶束解缔,胶束数量增多,胶束粒径减小,单分子自由链增加,有利于高分子表面活性剂向界面迁移和排布,这是高分子表面活性剂和碱复配体系与原油界面张力下降至超低值的主要原因.     

氢氧化钙粉末界面张力的测定

以Washburn方程为理论依据,采用毛细管上升法,设计了简易实验装置,测定了氢氧化钙粉末在水、二甲基亚砜和甘油中的润湿接触角.在此实验结果基础上,利用Y-G-G-F-V方程建立了计算固相表面张力和液-固界面张力的表达式,并分别计算出氢氧化钙粉末的表面张力、氢氧化钙与水、二甲基亚砜和甘油的液-固界面张力,为固体粉末的表...     

Wetting study of imidazolium ionic liquids

In this work, we present a systematic contact angles study of a series of 1-alkyl, 3-methyl-imidazolium ionic liquids (ILs) on well-defined polar and nonpolar monolayer surfaces supported on Si wafers. The advancing and receding contact angles of ILs were used to determine the surface energy of the monolayer surfaces using Neumann's equation-of-state and Zisman's critical surface tension approaches. In parallel, the contact angles of conventional probe fluids (molecular liquids) including water, formamide, methylene iodide, ethylene glycol, and hexadecane were determined on the same surfaces. The results obtained showed a great deal of similarity in wetting behavior of ionic vs molecular probe fluids: the contact angles of both sets of liquids followed the same patterns in accord with the surface tension of the fluid. A good agreement was found between the surface energy determined by different sets of liquids.     

Ultra-Low Interfacial Tension Between Heavy Oil and Betaine-Type Amphoteric Surfactants

Betaine surfactants with lipophilic groups of different lengths were synthesized in this research and the dynamic interfacial tension (IFT) between solutions of these surfactants and three kinds of crude oil from Shengli Oilfield are measured. The results indicated that, for Gudao and Gudong heavy oil, cetyl dimethyl hydroxyl sulfobetaine (SBET-16) was the most efficient in lowering the IFT in the case of no alkalis, while for Shengtuo heavy oil, cetyl dimethyl carboxymethyl betaine (CBET-16) was best. SBET-16 with the concentration of 0.003–0.1% and 0.005–0.1% can reduce the oil/water IFT to ultra-low for Gudao and Gudong oil respectively, CBET-16 with the concentration of 0.005–0.1% can lower the oil/water IFT to ultra-low for Shengtuo oil. These results showed that for different oils, an oil displacement agent with high capacity to lower the oil/water interfacial tension may be obtained only by changing the molecular structure of betaine surfactant. This study can be used to guide the design of surfactants for alkaline-free combination flooding.     

Experimental Study of the Effect of Strong Alkali on Lowering the Interfacial Tension of Oil/Heavy Alkylbenzene Sulfonates System

Experimental studies were conducted to explore the fundamental mechanisms of alkali to lower the interfacial tension of oil/heavy alkylbenzene sulfonates (HABS) system. Sodium hydroxide was used as the strong alkali chemical to investigate the interfacial tension (IFT) of oil/HABS system. The influences of salt and alkali on the interfacial activity were studied by the measurement of interfacial tension and partition coefficient. Moreover, the alkali/surfactant solutions were measured by dynamic laser scattering. The results showed that compared with the salt, the function of alkali to lower the interfacial tension and improve partition coefficient is more significant. The micelles formed by surfactants could be disaggregated because of adding alkali, so the size of micelles decreases and the number of mono‐surfactants increases, then more surfactant molecules move to the interface of oil/surfactant system and the adsorption of surfactants at oil‐water interfaces increases, which can lead to the decrease of IFT.     

Interfacial activity of a novel family of polymeric surfactants

A novel series of polymeric surfactants based on carboxy methyl cellulose and alkyl poly(etheroxy) acrylate were synthesized by ultrasonic irradiation. These polymeric surfactants have exhibit excellent surface activity due to their unique structure. The influences of salt, alcohol and alkali on the interfacial activity of these polymeric surfactants were studied by interfacial tensiometery, dynamic laser scattering (DLS), UV spectroscope and environmental scanning electrical microscope (ESEM). The surface tension and interfacial tension (IFT) properties change little with NaCl added. The formed micelles shrink, their size becomes smaller. Alcohols cause the IFT to decrease a little because a small amount of free chains present in solution. Under the influence of added alkali, the IFT of the polymeric surfactants, in aqueous solution, decreases so much that sometimes it is less than 10⁻² mN/m. Using data from the equivalent alkane scan, one cannot draw the conclusion that the action of alkali with the acidic components in crude oil leads to the ultra-low IFT. The analyses by UV, DLS and ESEM show that the micelles formed by polymeric surfactants could be disaggregated or destroyed sharply by the action of alkali. So the size of micelles decreases greatly and the number of free chains increases. That more polymeric surfactants molecules move to the interface of oil/water and rearrange at the interface of oil/water is believed to be the main reason of the ultra-low IFT (10⁻³ mN/m) that is obtained.     

Electron density matching as a guide to surfactant design

The effectiveness at reducing interfacial tension between water and different organic solvents was studied, with 14 structurally different dichain sulfosuccinate surfactants. Variations in chemical structure ranged from linear/branched alkyl tail groups, to phenyl-tipped tail units, to partially and fully fluorinated tails. The solvents n-heptane, toluene, and perfluoroheptane were used as example oil phases. Interfacial activity was measured in terms of a reduced interfacial tension scale, R(IFT), based on the value in the presence of surfactants compared to that for the pure solvent-water interface. Overall surfactant chain structure was determined to be the key factor affecting R(IFT). Furthermore, a strong correlation was observed between R(IFT) and the electron density rho(e) of the different surfactants: with any given oil, the most effective surfactants have rho(e) values closest to that for the solvent. For example, phenyl-tipped surfactants were shown to be comparatively more effective at the interface with an aromatic solvent (toluene) than with an aliphatic n-alkane (heptane). Furthermore, fluorination of the tail groups decreased effectiveness at the hydrocarbon/water interface, which was substantially increased at the fluorocarbon/water interface: this too followed the electron density-matching pattern. The importance of chain-tip chemical structure was also noted, with regard to the introduction of phenyl, CF3-, and H-CF2- terminal moieties. For branched alkyl-tailed surfactants, it was found that effectiveness could be linked to an empirical "branching factor". The significance of the electron density matching of organic solvent and surfactant for the prediction of interfacial activities is highlighted, and this concept may prove useful for the future design of new high-efficiency surfactants.     

Effect of electric fields on contact angle and surface tension of drops

Contact angles of sessile drops were experimentally investigated in the electric field. The experimental setup was designed such that the electric field was applied to all three interfaces. The advanced Automated Polynomial Fitting (APF) methodology was employed to measure contact angles with high accuracy. The significance of the observations and trends was examined by conducting statistical tests of hypothesis. It was found that contact angles of polar liquids such as alcohols increase in the electric field. However, no significant trend was observed for nonpolar liquids such as alkanes. The change in the contact angle was found to be stronger for liquids with longer molecules. It was shown that the polarity of the electric field is not an underlying factor in the observed trends. Using the equation of state for interfacial tensions, the observed shift in contact angles was translated into a corresponding change in surface tension of the liquids. The results suggest that the surface tension of alcohols increases by one to two percent (depending on the size of molecules) when an electric field of the order of magnitude of 10(6) V/m is applied.     

General Equations for the Equilibrium Shape of a Fluid Interface and for Its Angle of Contact with a Solid

Abstract

The classical equations of Young-Laplace (equilibrium shape of a fluid interface in a uniform gravitational field) and Young (angle of contact of the fluid interface with a solid) are generalized to take into account: (i) the presence of externally applied fields of any type; (ii) the variation of the interfacial tensions from point to point; (iii) the variation of the fluid interfacial tension with its orientation in space.

The general equations are deduced simultaneously by a variational method, which allows the determination of the minimum Helmholz energy configuration of a system comprising the two fluids and the solid. An axially symmetric geometry is assumed.

The equations so derived clarify the difficulties that have been found in the application of the classical equations-particularly Young's equation-to actual systems. Both equations, in their general form, contain terms that may be interpreted as representing the interaction between the three interfaces near their line of contact, and such an interaction cannot be ignored in actual systems.     

Relationship Between the Polymer Structures and Destabilization of Polymer‐Containing Water‐in‐Oil Emulsions

The viscous properties, scanning electronic microscopy (SEM), and water/oil interfacial tension (IFT) of partially hydrolyzed polyacryamide (HPAM) and hydrophobically associating hydrolyzed polyacryamides modified with N‐dodecylacrylamide were studied with the objective of investigating the influence on destabilization of emulsions. As expected, the copolymers exhibit significant viscosity enhancing capacity and three‐dimensional network structures due to intermolecular hydrophobic associations, and also present high interfacial activities as the IFT decrease with increasing polymer concentration. As a result, the existences of copolymers increased both the viscosity of emulsions and the intensity of interfacial film, in which case slow down the diffusion of demulsifier molecules and enhance the stability of emulsions, finally, the separation of water from oil becomes more difficult.     

Dynamics of capillary imbibition when surfactant, polymer, and hot water are used as aqueous phase for oil recovery

Capillary imbibition is an oil recovery mechanism in naturally fractured reservoirs if rock matrix is water wet and there is enough water in fractures in contact with matrix. It, however, may not yield an effective recovery under certain circumstances even if these conditions are maintained. Heavy matrix oil, high interfacial tension (IFT), oil-wet matrix sample, and limited contact area of matrix with water in fractures require additional effort to enhance the oil recovery by capillary imbibition. Chemicals and heat can be injected into naturally fractured reservoirs to improve the capillary imbibition recovery performance. With the involvement of low IFT fluid, heat, and polymer solution in the process, capillary imbibition dynamics may change and this entails an identification of the dynamics of the process through laboratory experiments before injection of these expensive fluids into oil reservoirs. In this study, the dynamics of capillary imbibition was studied experimentally. Static imbibition experiments were conducted on oil- and water-wet rock samples under different boundary conditions and saturated with different types of oil. The analyses were conducted using three indicators, namely the capillary imbibition rate, ultimate oil recovery, and shape of the recovery profile. Based on these indicators, the dynamics of capillary imbibition of different aqueous phases were evaluated for different oil types and matrix properties. The conditions that cause weak or strong capillary imbibition were identified.