电解-电化学混合电容器的制备与性能

为解决电化学电容器工作电压过低的问题, 本文以钽电解电容器的烧结型钽块为阳极, 聚苯胺(PANI)/TiO₂电化学电容器复合电极为阴极, 成功制备了高能量密度、高工作电压的电解-电化学混合电容器. PANI/TiO₂复合电极是通过在多孔阳极氧化钛纳米管阵列中电化学聚合PANI 制得. 该阴极具有优良的倍率特性, 当平均功率密度为0.55 mW·cm^-2时, 对应的比容量仍达到10.0 mF·cm^-2. 由于与电解电容器复合, 该混合电容器的单元工作电压可高达100 V. 而且电化学电容器阴极的比容量远大于阳极, 故阴极所需尺寸远小于阳极, 节省的空间可用于增大阳极尺寸, 从而使混合电容器的比容量极大提高. 所制备的混合电容器体积能量密度和质量能量密度分别是钽电解电容器的4 倍和3 倍. 将该混合电容器在100 V下进行短路充放电实验, 循环10000 次后发现容量未衰减, 等效串联电阻未增加, 显示出极好的循环稳定性和功率特性. 计算表明其最大功率密度高达847.5 W·g^-1. 电化学阻抗谱显示其具有优良的阻抗特性和频率特性.     

Hierarchical nanocomposites of polyaniline scales coated on graphene oxide sheets for enhanced supercapacitors

The homogeneous polyaniline–graphene oxide (PANI-GO) nanocomposites were facilely assembled with a redox system in which cumene hydroperoxide (CHP) and iron dichloride (FeCl₂) acted as oxidant and reductant, respectively. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) images showed that PANI scales coated uniformly on the surface of GO sheets owing to the synergistic effect between the PANI and GO. The obtained PANI-GO nanocomposites exhibited improved electrochemical performance as an electrode material for supercapacitors compared with the pure PANI. The specific capacitance of the PANI-GO nanocomposites was high up to 308.3 F g^?1, much higher than that of the pure PANI with specific capacitance of 150 F g^?1 at a current density of 1 A g^?1 in 2 M H₂SO₄ electrolyte. The Raman and XPS results illustrated that enhanced electrochemical performance might be attributed to the π-π conjugation between the PANI and GO sheets.     

High-performance supercapacitor electrode based on a nanocomposite of polyaniline and chemically exfoliated MoS<Subscript>2</Subscript> nanosheets

In this study, MoS₂ nanosheets were first prepared by exfoliating its bulk material in HCl/LiNO₃ solution with a yield of 45%, and then a facile strategy was developed to synthesize polyaniline/MoS₂ (PANI/MoS₂) nanocomposite via in situ polymerization. Structural and morphological characterizations of MoS₂ nanosheets and the nanocomposite were investigated by scanning electron microscope (SEM), transmission electron microscope (TEM), and X-ray powder diffraction. The results of SEM illustrated that orderly sawtooth polyaniline (PANI) nanoarrays were formed on the surface of MoS₂ nanosheets. The nanocomposite displayed good electrochemical performance as a supercapacitor electrode material. The specific capacitance reached 560 F/g at a current density of 1.0 A g^?1 in 1.0 M H₂SO₄ solution. Such good performance is because that the MoS₂ nanosheets provided a highly electrolytic accessible surface area for redox-active PANI and a direct path for electrons.     

Enhanced specific energy of silver-doped MnO2/graphene oxide electrodes as facile fabrication symmetric supercapacitor device

The present work is about the preparation of silver (Ag)-doped manganese oxide (MnO₂)/graphene oxide (GO) composite thin films are deposited by a facile and binder-free successive ionic layer adsorption and reaction (SILAR) method for the first time. The Brunauer-Emmett-Teller (BET) study revealed the nanosheets of MnO₂–Ag3/GO exhibit high specific surface area of 192 m² g^?1. The tailored flower-like morphology and interconnected nanosheets of MnO₂–Ag3/GO electrodes achieved high electrochemical performance. The maximum specific capacitance (Cs) of 877 F g^?1 at the scan rate of 5 mV s^?1 is obtained for MnO₂–Ag3/GO electrode tested in 1 M sodium sulfate (Na₂SO₄) electrolyte with capacity retention of 94.57% after 5000 cycling stability. The MnO₂–Ag3/GO composite-based flexible solid state symmetric supercapacitor (FSS-SSC) device delivered Cs as 164 F g^?1 with specific energy of 57 Wh kg^?1 at specific power of 1.6 kW kg^?1 and capacitive retention of 94% after 10,000 cycles.     

Enhanced Supercapacitor Performance Using a Co3O4@Co3S4 Nanocomposite on Reduced Graphene Oxide/Ni Foam Electrodes

To avoid an enormous energy crisis in the not-too-distant future, it be emergent to establish high-performance energy storage devices such as supercapacitors. For this purpose, a three-dimensional (3D) heterostructure of Co₃O₄ and Co₃S₄ on nickel foam (NF) that is covered by reduced graphene oxide (rGO) has been prepared by following a facile multistep method. At first, rGO nanosheets are deposited on NF under mild hydrothermal conditions to increase the surface area. Subsequently, nanowalls of cobalt oxide are electro-deposited on rGO/Ni foam by applying cyclic-voltammetry (CV) under optimized conditions. Finally, for the synthesis of Co₃O₄@Co₃S₄ nanocomposite, the nanostructure of Co₃S₄ was fabricated from Co₃O₄ nanowalls on rGO/NF by following an ordinary hydrothermal process through the sulfurization for the electrochemical application. The samples are characterized by using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The obtained sample delivers a high capacitance of 13.34 F cm⁻² (5651.24 F g⁻¹) at a current density of 6 mA cm⁻² compared to the Co₃O₄/rGO/NF electrode with a capacitance of 3.06 F cm⁻² (1230.77 F g⁻¹) at the same current density. The proposed electrode illustrates the superior electrochemical performance such as excellent specific energy density of 85.68 W h Kg⁻¹, specific power density of 6048.03 W kg⁻¹ and a superior cycling performance (86% after 1000 charge/discharge cycles at a scan rate of 5 mV s⁻¹). Finally, by using Co₃O₄ @Co₃S₄/rGO/NF and the activated carbon-based electrode as positive and negative electrodes, respectively, an asymmetric supercapacitor (ASC) device was assembled. The fabricated ASC provides an appropriate specific capacitance of 79.15 mF cm⁻² at the applied current density of 1 mA cm⁻², and delivered an energy density of 0.143 Wh kg⁻¹ at the power density of 5.42 W kg⁻¹.     

Synthesis of nickel selenide thin films for high performance all-solid-state asymmetric supercapacitors

As a significant semiconductor, nickel selenide shows enormous potential and extensive application prospects in the field of sensor, photocatalysis and supercapacitor. In this paper, nickel selenide (Ni₃Se₂, NiSe) thin films were successfully fabricated on stainless-steel sheet using a facile, effective electrodeposition technique. The morphologies, microstructures and chemical compositions of the thin films are characterized systematically. Electrochemical tests exhibit that the Ni₃Se₂ and NiSe possess high specific capacitance of 581.1 F/g and 1644.7 F/g, respectively. A flexible, all-solid-state asymmetric supercapacitor is assembled by utilizing NiSe film as positive electrode and activated carbon as negative electrode. The solid device delivers a high areal capacitance of 27.0 mF/cm² at the current density of 0.7 mA/cm². The maximum volumetric energy density and power density of the NiSe//AC asymmetric SCs can achieve 0.26 mWh/cm³ and 33.35 mW/cm³, respectively. The device shows robust cycling stability with 84.6% capacitance retention after 10,000 cycles, outstanding flexibility and satisfactory mechanical stability. Moreover, two devices in series can light up a red light-emitting diode, which displayed great potential applications for energy storage.     

Sacrificial template synthesis of ultrathin polyaniline nanosheets and their application in highly sensitive electrochemical dopamine detection

Unique functional nanomaterials as electroactive media for efficiently electrochemical biosensing have always been an ever-increasing topic in biotechnology and environmental fields. In this study, we report a simple sacrificial template-guided polymerization strategy to fabricate ultrathin two-dimensional (2D) polyaniline (PANI) nanosheets for electrochemical detection of dopamine (DA). By using vanadium pentoxide nanosheets as both sacrificial templates and oxidants, the resulting PANI nanosheets show an ultrathin thickness of ca. 4 nm with a favorable electrical conductivity of ca. 10 S cm^?1. Furthermore, PANI nanosheets have been modified on a glass carbon electrode for highly sensitive DA detection. The proposed DA sensor delivers a linear range of 0.5–300 μM with a low detection limit of 0.118 μM (S/N = 3). In addition, the as-fabricated electrochemical sensor exhibits an outstanding selectivity, stability, reproducibility, and repeatability, enabling its feasible application for DA detection in real samples. Therefore, the ultrathin PANI nanosheets reported here are good candidates as electrodes for the sensitive and selective DA detection.     

Indium oxide co-doped with tin and zinc: A simple route to highly conducting high density targets for TCO thin-film fabrication

Indium oxide co-doped with tin and zinc (ITZO) ceramics have been successfully prepared by direct sintering of the powders mixture at 1300 °C. This allowed us to easily fabricate large highly dense target suitable for sputtering transparent conducting oxide (TCO) films, without using any cold or hot pressing techniques. Hence, the optimized ITZO ceramic reaches a high relative bulk density (∼ 92% of In₂O₃ theoretical density) and higher than the well-known indium oxide doped with tin (ITO) prepared under similar conditions. All X-ray diagrams obtained for ITZO ceramics confirms a bixbyte structure typical for In₂O₃ only. This indicates a higher solubility limit of Sn and Zn when they are co-doped into In₂O₃ forming a solid-solution. A very low value of electrical resistivity is obtained for [In₂O₃:Sn_0.10]:Zn_0.10 (1.7 × 10⁻³ Ω cm, lower than ITO counterpart) which could be fabricated to high dense ceramic target suing pressure-less sintering.     

Electrochemical performance of Co–Al layered double hydroxide nanosheets mixed with multiwall carbon nanotubes

Regular hexagonal Co–Al layered double hydroxides (Co–Al LDH) were synthesized by urea-induced homogeneous precipitation. This material proved to be nanosheets by scanning electron microscopy and X-ray diffraction measurements. The electrochemical capacitive behavior of the nanosheets in 1 M KOH solution were evaluated by constant current charge/discharge and cyclic voltammetric measurements, showing a large specific capacitance of 192 F·g⁻¹ even at the high current density of 2 A·g⁻¹. When multiwall carbon nanotubes (MWNTs) were mixed with the Co–Al LDH, it was found that the specific capacitance and long-life performance of all composite electrodes at high current density are superior to pure LDH electrode. When the added MWNTs content is 10 wt%, the specific capacitance increases to 342.4 F·g⁻¹ and remains at a value of 304 F·g⁻¹ until the 400th cycle at 2 A·g⁻¹, showing that this is a promising electrode material for supercapacitors working at heavy load. According to the electrochemical impedance spectra, MWNTs greatly increase the electronic conductivity between MWNTs and the surface of Co–Al LDH, which consequently facilitates the access of ions in the electrolyte and electrons to the electrode/electrolyte interface.     

Hydrothermal synthesis of reduced graphene sheets/Fe2O3 nanorods composites and their enhanced electrochemical performance for supercapacitors

Reduced graphene nanosheets/Fe₂O₃ nanorods (GNS/Fe₂O₃) composite has been fabricated by a hydrothermal route for supercapacitor electrode materials. The obtained GNS/Fe₂O₃ composite formed a uniform structure with the Fe₂O₃ nanorods grew on the graphene surface and/or filled between the graphene sheets. The electrochemical performances of the GNS/Fe₂O₃ hybrid supercapacitor were tested by cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge–discharge tests in 6 M KOH electrolyte. Comparing with the pure Fe₂O₃ electrode, GNS/Fe₂O₃ composite electrode exhibits an enhanced specific capacitance of 320 F g⁻¹ at 10 mA cm⁻² and an excellent cycle-ability with capacity retention of about 97% after 500 cycles. The simple and cost-effective preparation technique of this composite with good capacitive behavior encourages its potential commercial application.     

A high-performance asymmetric supercapacitor achieved by surface-regulated MnO2 and organic-framework–derived N-doped carbon cloth

It is possible to achieve high energy density and power density simultaneously for asymmetric supercapacitors by using pseudocapacitive materials with abundant ion intercalation/de-intercalation sites on the surface. Herein, a positive electrode based on feather-like MnO₂ anchored on the activated carbon cloth is prepared, in which oxygen-enriched MnO₂ nanorods with a radial sheet-like structure (OMO@AC) further form via electrochemical oxidation. Because of the large contact area with electrolyte and abundant oxidation functional groups on its surface, the OMO@AC displays excellent capacitance of 3,160 mF/cm² at 1 mA/cm². For the nitrogen-doped active carbon negative electrode, the capacitance is up to 1,875 mF/cm² at 4 mA/cm² due to the increase in disorder and defect on the carbon surface by N-doping. Furthermore, we verify the good electrochemical activity on the OMO@AC electrode surface by first-principles calculations and confirm the good matching degree between the positive and negative electrodes by CV testes. The aqueous oxygen-enriched MnO₂// nitrogen-doped active carbon asymmetric supercapacitor exhibits an ultrahigh energy density of 8.723 mWh/cm³ at a power density of 14.248 mW/cm³ and display excellent cycle stability maintaining 95.5% after 10,000 cycles. The facile synthesis method and excellent performance provide a feasible way for the preparation of high-performance electrode materials for energy storage devices.     

Potentiostatically deposited nanostructured α-Co(OH)2: A high performance electrode material for redox-capacitors

A high specific capacitance was obtained for α-Co(OH)₂ potentiostatically deposited onto a stainless-steel electrode in 0.1 M Co(NO₃)₂ electrolyte at −1.0 V vs. Ag/AgCl. The structure and surface morphology of the obtained α-Co(OH)₂ were studied by using X-ray diffraction analysis and scanning electron microscopy. A network of nanolayered α-Co(OH)₂ sheets was obtained; the average thickness of individual α-Co(OH)₂ sheets was 10 nm, and the thickness of the deposit was several micrometers. The capacitive characteristics of the α-Co(OH)₂ electrodes were investigated by means of cyclic voltammetry and constant current charge–discharge cycling in 1 M KOH electrolyte. A specific capacitance of 860 F g⁻¹ was obtained for a 0.8 mg cm⁻² α-Co(OH)₂ deposit. The specific capacitance did not decrease significantly for the active mass loading range of 0.1–0.8 mg cm⁻² due its layered structure, which allowed easy penetration of electrolyte and effective utilization of electrode material even at a higher mass. This opens up the possibility of using such materials in supercapacitor applications.     

Co(OH)2-combined carbon-nanotube array electrodes for high-performance micro-electrochemical capacitors

We have investigated binder-free Co(OH)₂-combined carbon-nanotube (CNT) array electrodes using anodized aluminum oxide (AAO) templates for micro-electrochemical capacitors. It is shown that compared to the capacitors fabricated with CNT only electrodes (6.3 F/cm³ at 100 mV/s), those with the Co(OH)₂-combined CNT array electrodes produce much higher capacitance (12.74 F/cm³ at 100 mV/s) together with superior high-rate capacitance. The improved electrochemical behavior is explained in terms of high capacitance of amorphous Co(OH)₂ electrode and the use of CNT arrays as effective current collector.     

Facile hydrothermal synthesis of zinc sulfide nanowires for high-performance asymmetric supercapacitor

A facile, single-step hydrothermal route is followed to prepare ZnS nanowires with large aspect ratios. The obtained ZnS nanowires deposited on nickel foam (ZnS/Ni-foam) exhibit a specific capacitance of 781 F/g at a current density of 0.5 A/g. An asymmetric supercapacitor fabricated from ZnS/Ni-foam as a positive electrode and jute derived activated carbon coated on Ni-foam (JAC/Ni-foam) as a negative electrode attains a high specific capacitance of 573 F/g at a current density of 0.5 A/g, with an accompanying high energy density of 51 Wh/kg at a power density of 200 W/kg in an extensive operating potential window of 1.2 V. In addition, the ZnS//JAC asymmetric supercapacitor reveals long-term cyclic stability, after 10,000 GCD cycles the device sustain around ～87 % of the initial specific capacitance. These results shed enlighten a new opportunity for promising electrode materials in supercapacitors.     

Graphene oxide doped polyaniline for supercapacitors

A novel high-performance electrode material based on fibrillar polyaniline (PANI) doped with graphene oxide sheets was synthesized via in situ polymerization of monomer in the presence of graphene oxide, with a high conductivity of 10 S cm^?1 at 22 °C for the obtained nanocomposite with a mass ratio of aniline/graphite oxide, 100:1. Its high specific capacitance of 531 F/g was obtained in the potential range from 0 to 0.45 V at 200 mA/g by charge–discharge analysis compared to 216 F/g of individual PANI. The doping and the ratio of graphene oxide have a pronounced effect on the electrochemical capacitance performance of the nanocomposites.     

Nanostructured ferrite/graphene/polyaniline using for supercapacitor to enhance the capacitive behavior

Graphene nanosheets, polyaniline (PANI), and nanocrystallites of transition metal ferrite {Fe₃O₄ (Mag), NiFe₂O₄ (NiF), and CoFe₂O₄ (CoF)} have been prepared and characterized via XRD, FTIR, SEM, TEM, UV–vis spectroscopy, cyclic voltammetry, galvanostatic charge discharges, and impedance spectroscopy. Electrochemical measurements showed that supercapacitances of hybrid electrodes made of the ternary materials are higher than that of hybrid electrode made of binary or single material. The ternary hybrid CoF/graphene (G)/PANI electrode exhibits a highest specific capacitance reaching 1123 Fg^?1, an energy density of 240 Wh kg^?1 at 1 A g^?1, and a power density of 2680 Wkg^?1 at 1 A g^?1 and outstanding cycling performance, with 98.2% capacitance retained over 2000 cycles. The extraordinary electrochemical performance of the ternary CoF/G/PANI hybrid can be attributed to the synergistic effects of the individual components. The PANI conducting polymer enhances an electron transport. The Ferrite nanoparticles prevent the restocking of the carbon sheets and provide Faradaic processes to increase the total capacitance.     

Laser processed micro-supercapacitors based on carbon nanotubes/manganese dioxide nanosheets composite with excellent electrochemical performance and aesthetic property

A laser processed micro-supercapacitor (LPMS) based on carbon nanotubes/manganese dioxide composite is fabricated through slurry dispensing and laser scribing techniques. This device presents superior electrochemical performance and aesthetic property.     

RECTIFYING EFFECT OF POLYANILINE(PANI)/N-TYPE POROUS SILICONE HETEROJUNCTION*

Heterojunctions between polyaniline (PANI) and n-type porous silicon (PS), Al/PS-PANI/Au cell,were fabricated, and the rectifying parameters of this heterojunction diode were measured as a function of thepreparation conditions of PANI and PS, the electronic structure of PANI as well as cell structure. Therectifying parameters of Al/PS-PANI/Au cell were determined to be γ= 1 .8×10~1～ 1 .0×10~5 for the rectifyingratio at 3V, n = 3 ～12 for the ideal factor,j_0 = 8.0×10~(-5)～5.6×10~(-2) mA/cm~2 for the reversed saturated currentdensity, and φ_b = 0.67～ 0.83 V for the barrier height, respectively. The best rectifying heterojunction diodemade between PANI and n-type PS with higher rectifying factor (γ= 1 .0×10~5 at 3V ), output current (>1500mA/cm~2 at 3V) and lower ideal factor (n = 3.3) was obtained by preventing the oxidation of PS beforeevaporating Al electrode.     

Effect of post-deposition annealing temperature on RF-sputtered HfO2 thin film for advanced CMOS technology

Structural and electrical properties of HfO₂ gate-dielectric metal-oxide-semiconductor (MOS) capacitors deposited by sputtering are investigated. The HfO₂ high-k thin films have been deposited on p-type <100> silicon wafer using RF-Magnetron sputtering technique. The Ellipsometric, FTIR and AFM characterizations have been done. The thickness of the as deposited film is measured to be 35.38 nm. Post deposition annealing in N₂ ambient is carried out at 350, 550, 750 °C. The chemical bonding and surface morphology of the film is verified using FTIR and AFM respectively. The structural characterization confirmed that the thin film was free of physical defects and root mean square surface roughness decreased as the annealing temperature increased. The smooth surface HfO₂ thin films were used for Al/HfO₂/p-Si MOS structures fabrication. The fabricated Al/HfO₂/p-Si structure had been used for extracting electrical properties such as dielectric constant, EOT, interface trap density and leakage current density through capacitance voltage and current voltage measurements. The interface state density extracted from the G–V measurement using Hill Coleman method. Sample annealed at 750 °C showed the lowest interface trap density (3.48 × 10¹¹ eV⁻¹ cm⁻²), effective oxide charge (1.33 × 10¹² cm⁻²) and low leakage current density (3.39 × 10⁻⁹ A cm⁻²) at 1.5 V.     

Conducting Polyaniline Nanowire Arrays Modified Electrode for High Performance Supercapacitor and Enhanced Catalysis of Nitrite Reduction

Vertically aligned conducting polymer nanowire arrays had great potential applications in supercapacitor electrode material and exhibited enhanced electrocatalytic behavior towards the reduction of nitrite. In this paper, a facial template‐free approach to synthesize large arrays of vertically aligned polyaniline (PANI) nanowires on electrochemically pretreated glassy carbon electrodes was reported by using a galvanostatic current method. The as‐prepared large arrays of PANI nanowires had very narrow diameters and were oriented perpendicular to the substrate, which was a benefit to the ion diffusion when being used as the supercapacitor electrode. The highest specific capacitance of PANI nanowire arrays was measured and kept high at a large charge‐discharge current density. Furthermore, it also can detect nitrite with ultrahigh sensitivity of 62.99 µA mM^?1 cm^?2 and a remarkable fast response time of less 1 s. The results indicated that the vertically aligned PANI nanowires could dramatically enhance the electrochemical performance.