Assessment of corrosion protection and performance of bio-based polyurethane acrylate incorporated with nano zinc oxide coating

In this study, a series of UV-curable anticorrosive PUA coatings embedded with varying concentrations of inorganic ZnO fillers have been successfully prepared from jatropha-based polyol. The electrochemical impedance spectroscopy (EIS) and Tafel polarisation analysis revealed that increasing fillers composition lead to the improvement of the anticorrosive property of the hybrid coatings. Meanwhile, the salt spray test results were found to correlate with the EIS of C_c (F cm⁻²) was 2.71 × 10⁻⁹, Bode plot - 10⁶ Ω cm² and Tafel polarisation results 7.56 × 10⁻⁶ MPY at 3 wt% of ZnO. Physical properties of 3 wt% loading of ZnO fillers in hardness test obtained 6H which was strongly attributed to the low interfacial interaction and poor dispersion of the fillers within the polymer matrix.     

Effect of formulation of silica‐based solution on corrosion resistance of silicate coating on hot‐dip galvanized steel

Several silica‐based solutions with 50 g/l of SiO₂ were prepared from sodium silicate solutions and silica sol; the silicate conversion coatings were obtained by immersing hot‐dip galvanized steel sheets in these solutions. These solutions were characterized using high‐resolution transmission electron microscopy and ²⁹Si nuclear magnetic resonance; the morphology of the coatings was observed by SEM and atomic force microscopy while the corrosion resistance was evaluated by electrochemical measurements as well as neutral salt spray tests. The results show that the coatings obtained from the single silica sol solution had poor adhesion and the coating obtained from the sodium silicate solution with low SiO₂/Na₂O molar ratio was uneven. By adding the silica sol to the silicate solution with low molar ratio, uniform coatings with better protection property were obtained. According to the results of ²⁹Si nuclear magnetic resonance spectra, the effects of the distribution of silicate anions with various polymerization degrees in the silica‐based solutions on the microstructure and corrosion resistance of the silicate coatings are discussed. Copyright © 2016 John Wiley & Sons, Ltd.     

Cupressus arizonica fruit essential oil: A novel green inhibitor for acid corrosion of carbon steel

Natural-based corrosion inhibitors have gained great research interest thanks to their low cost and higher performance. The Cupressus arizonica fruit essential oil (CAFEO) has a higher extraction yield than leaves; however, it has less antibacterial and antifungal activities. The three main components in the CAFEO were α-pinene (51.07%), myrcene (17.92%), and limonene (9.66%). Essential oils with a higher percentage of α-pinene were found to have outstanding corrosion inhibition properties. Therefore, herein, the CAFEO was investigated as a green corrosion inhibitor for carbon steel (CS) in 1.0 mol/L HCl using electrochemical, i.e., potentiodynamic polarization (PDP) and electrochemical impedance spectroscopy (EIS), and scanning electron microscope (SEM) techniques. The experimental results revealed that CAFEO successfully inhibited the carbon steel corrosion in 1.0 mol/L HCl solution. Results from PDP indicated that the inhibitor had a mixed-type effect with a predominance cathodic character. EIS data showed that the charge transfer resistance of the CS electrode increased from 20.9 Ω cm² in blank solution to 294.5 Ω cm² in HCl solution inhibited with 0.5 g/L of CAFEO at 298 K, leading to a significant decrease in the double layer capacitance values and an inhibition efficiency (η%) of 93%. The high temperatures showed a negative effect on the corrosion inhibition efficiency of the tested inhibitor. At 323 K, the η% of CAFEO decreased to 77%. Besides, SEM images showed that the inhibitor formed a protective barrier against acid attack, preventing carbon steel from corrosion. Theoretical calculations by Density Functional Theory (DFT) were performed to investigate the reactivity of the three main components of CAFEO.     

Synthesis of oxalate doped polyaniline and its corrosion protection performance

It is known that dopants present in polyaniline (PANI) play an important role in corrosion protection of mild steel since the dopant ions form a secondary layer with iron. Since oxalate ions form a stable iron oxalate layer on mild steel, a study has been made on the corrosion protection performance of steel by vinyl coating containing oxalate doped PANI in acid and neutral media. Electrochemical impedance spectroscopy (EIS) studies have shown that the oxalate doped PANI is able to protect mild steel in sodium chloride solution since the impedance values are maintained at 10¹⁰ Ω cm² even after 100 days of exposure.     

Designing an epoxy composite coating having dual-barrier-active self-healing anti-corrosion functions using a multi-functional GO/PDA/MO nano-hybrid

The graphene oxide, functionalized with polydopamine (PDA) bio-polymers and molybdate (MO) ions, was incorporated into the epoxy coating. The FT-IR, Raman, UV-visible, XRD, and FE-SEM/EDS analyses were utilized for the GO/PDA/MO nanoparticle characterization. The sequence of inhibitors' release from the nano-hybrid and their effect on the electrochemical behavior of the steel sample was explored by the OCP, polarization, and, EIS analyses in the aquatic saline media. EIS analyses revealed inhibition efficiency of 88% for the sample immersed in the GO/PDA/MO-contained solution after 48 h immersion. The polarization results showed a 91% corrosion mitigation index for the sample submerged in the GO/PDA/MO extract-containing solution after 48 h immersion. An increase of the scratched coating Nyquist diameter, the lower corrosion product, and coating blister formation after exposure to the salt spray chamber, as well as the lower adhesion loss in the pull-off test (26%), revealed that the epoxy coating reinforced with GO/PDA/MO nano-hybrids could mitigate the mild steel corrosion by improving the barrier performance and active corrosion protection (self-healing mechanism) behavior.     

A zirconia-polyester glycol coating on differently pretreated AISI 316L stainless steel: corrosion behavior in chloride solution

The effect of zirconia and zirconia-polyester glycol hybrid coatings on the corrosion resistance of mechanically polished or anodized AISI 316 stainless steel (316L), was studied by potentiodynamic polarization and electrochemical impedance spectroscopy in 0.1 M NaCl and scanning electron microscope and atomic force microscopy examinations. The deposition of zirconia coatings was achieved by the sol–gel technique by immersing the samples in either the inorganic polymer or the organic–inorganic polymer mixture. From potentiodynamic and impedance measurements, the grade of protection is reduced with the exposure time to the electrolyte, which is mainly associated with lost of film adhesion and, consequently, detachment from the metal substrate. However, the uncoated anodized sample revealed an unexpected corrosion behavior; the anodic film formed during anodizing readily increased the corrosion resistance of the 316L stainless steel in 0.1 M NaCl, revealing a considerable reduction in the corrosion current density and an increase in the pitting potential.     

Electrochemical corrosion behaviors and corrosion protection properties of Ni–Co alloy coating prepared on sintered NdFeB permanent magnet

In this study, a protective Ni–Co alloy coating was prepared on sintered NdFeB magnet applying electrodeposition technique. A pure nickel coating was also studied for a comparison. The microstructure, surface morphologies, and chemical composition of coatings were investigated using X-ray diffraction, scanning electron microscope, and energy dispersive spectroscopy, respectively. The corrosion protection properties of coatings for NdFeB magnet in neutral 3.5 wt.% NaCl solutions were evaluated by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) techniques. The microstructure and surface morphologies analysis showed that the addition of cobalt element into matrix metal Ni altered the preferential orientation of pure nickel coating from (2 0 0) crystal face for pure nickel coating to (1 1 1) crystal face for Ni–Co alloy coating, and made the surface morphologies more compact and uniform due to the grain-refining. The results of potentiodynamic polarization test showed that compared with pure nickel coating, Ni–Co alloy coating exhibited much nobler corrosion potential (E _corr) and lower corrosion current density (j _corr), indicating better anticorrosive properties. The long-term immersion test by dint of EIS indicated that the Ni–Co alloy coating still presented high impedance value of 1.9 × 10⁵ Ω cm² with the immersion time of 576 h indicating the excellent anticorrosive properties, and corrosion protection properties of nickel coating for NdFeB magnet practically disappeared with the immersion time of 144 h, which also indicated that the Ni–Co alloy coating provided better corrosion protection properties for the NdFeB magnet compared with nickel coating.     

Evaluation of the corrosion resistance of electroless Ni-P and Ni-P composite coatings by electrochemical impedance spectroscopy

Electroless Ni-P composite coatings have gained a good deal of popularity and acceptance in recent years as they provide considerable improvement of desirable qualities such as hardness, wear, abrasion resistance, etc. The disagreement among researchers on the corrosion behaviour of these coatings warrants a thorough investigation. Among the various techniques available for the determination of corrosion resistance, electrochemical impedance spectroscopy (EIS) is considered to be superior as it provides not only an assessment of the corrosion resistance of different deposits but also enables the mechanistic pathway by which the deposits become corroded to be determined. The present investigation focuses on the evaluation of the corrosion resistance of electroless Ni-P and Ni-P-Si₃N₄, Ni-P-CeO₂ and Ni-P-TiO₂ composite coatings produced using an acidic hypophosphite-reduced electroless nickel bath, using EIS. The study makes evident that the same fundamental reaction is occurring on all the coatings of the present study but over a different effective area in each case. The charge transfer resistance of electroless Ni-P and Ni-P composite deposits are in the range 32,253–90,700 Ω cm², whereas the capacitances of these coatings are in the range 11–17 μF/cm². The improved corrosion resistance obtained for electroless Ni-P and Ni-P composite coatings is due to the enrichment of phosphorus on the electrode surface, which enables the preferential hydrolysis of phosphorus over that of nickel. The better corrosion resistance obtained for electroless Ni-P composite coatings can be ascribed to the decrease in the effective metallic area prone to corrosion. Among the three electroless Ni-P composite coatings, the corrosion resistance is in the following order: Ni-P-CeO₂=Ni-P-Si₃N₄>Ni-P-TiO₂. Electronic Publication     

Layer-By-Layer (LBL) hybrid MOF coating for graphene-based multilayer composite: Synthesis and application as anode for lithium ion batteries

The hybrid anodic materials with high porosity and low charge resistance exhibit high specific capacity and stable cyclic stability for lithium ion battery (LIBs). For this purpose, three-dimensional hollow material, metal organic framework (MOF-199) was coated over the active surface of oxidized derivative of graphene (Graphene oxide, GO), via layer-by-layer (LBL) coating method. Cupric acetate and benzene-1,3,5-tricarboxylic acid [Cu₃(BTC)₂], were alternatively coated on the active surface of GO as an anode material, to enhance the structural diversity and reduce the synergistic effect of insertion and extraction of Li⁺ ions for LIBs. Sharp absorption peaks from 1620 cm⁻¹ to 1360 cm⁻¹ and intense ring bends ∼1000 cm⁻¹ was identified through FTIR. Powder XRD provides the evidence for size reduction of Cu₃(BTC)₂@GO composite (32.6 nm) comparative to GO (43.7 nm). Outcome of EIS analysis shows the charge transfer resistance of simple GO is 2410 Ω, which is 4 times higher than R_ct of Cu₃(BTC)₂@GO composite (590 Ω). Similarly the Warburg impedance co-efficient for simple GO (448.8 Ωs^−1/2) is also higher than A_w of Cu₃(BTC)₂@GO composite (77.64 Ωs^−1/2). The synthesized material show high initial charge/discharge capacity, 1200/1420 mAh/g with 85% Coulombic efficiency and reversible discharge capacity, 1296 mAh/g after 100 cycles at 100 mA/g current density. The 98.9% Coulombic efficiency and 91% retaining capacity of composite at 100th cycle with cyclic stability, provides the phenomenon approach towards the rechargeable LIBs for industrial technology.     

Analysis of deterioration process of organic protective coating using EIS assisted by SOM network

Under cyclic wet–dry conditions, the deterioration process of the organic coating on carbon steel surface has been studied using electrochemical impedance spectroscopy (EIS) assisted by self-organizing feature map (SOM) network. According to the EIS characteristics, changing rate of impedance and the classification results by SOM network, the entire deterioration process can be divided into three main stages shown as follows. Stage I is the medium penetration into coatings, which is a slow process. Stage II is the corrosion initiation under coatings, which is a relatively fast transition period. Stage III is the corrosion extension which causes coating delamination and makes the coatings lose its corrosion protection eventually. Besides, the results indicate that SOM network is a very simple and effective technique for analyzing the deterioration process of organic coating.     

Zn-Al-[V10O28]6-双层氢氧化物掺杂对LY12铝合金表面溶胶-凝胶涂层性能的影响

采用共沉淀法制备Zn-Al-[V₁₀O₂₈]^6-双层氢氧化物(以下简称LDH-V), 研究不同添加浓度(0.0、0.25×10^-3、0.75×10^-3、1.5×10^-3、3.0×10^-3 mol·L^-1)的LDH-V对LY12 铝合金溶胶-凝胶涂层形貌、耐蚀性的影响. 采用扫描电子显微镜(SEM)和傅里叶变换红外(FTIR)光谱研究LDH-V对涂层形貌和结构的影响. 运用中性盐雾实验对涂层进行耐蚀性评估. 利用电化学方法对涂层在0.05 mol·L^-1的NaCl 溶液中的腐蚀行为进行研究. 探讨加入LDH-V后溶胶-凝胶涂层的耐蚀机理. 结果表明, 一定量LDH-V的加入不仅可以提高溶胶-凝胶涂层的耐蚀性能, 还可对涂层被破坏区域进行自修复, 起到延缓铝合金基体腐蚀的作用. 然而, 当LDH-V的添加溶度超过一定值时, 会破坏涂层的完整性并降低涂层的腐蚀防护性能. 实验结果表明LDH-V最佳的添加浓度为1.5×10^-3mol·L^-1.     

Investigation of Glass-Like Sol-Gel Coatings for Corrosion Protection of Stainless Steel Against Liquid and Gaseous Attack

Glass-like sol-gel coatings have been investigated as corrosion protective coatings on stainless steel. Magnesium- and borosilicate coatings with thickness of about 100–700 nm and methyl-modified SiO2 coatings with a thickness of about 2 m were deposited on stainless steel plates by dip-coating. The coatings were densified between 400°C and 500°C in different atmospheres (N2, air) for 1 h. The corrosion protection against gaseous attack was investigated by accelerated corrosion tests, at 800°C in air for 1 h. A corrosion protection factor was calculated from the relation Fe/Fe2O3, determined by XRD on the surface of coated and uncoated samples. Methyl-modified SiO2 coatings showed a protection factor, which was 2 orders of magnitude higher than for the other coatings. Electrochemical investigations were performed on samples submerged in a NaCl solution for 200 h. The corrosion propagation, polarization resistance and impedance vector were measured. For accelerated corrosion tests, polarization intensity curves were determined for high potentials of up to 1 V. Again excellent results were obtained for the methyl-modified SiO2 coatings, which remained passive for 200 h. Results of the salt spray corrosion test, however, showed no corrosion protection by the sol-gel coatings. After 2000 h in the salt spray chamber the steel was corroded and the coatings peeled off. It is concluded that for the further development of these coatings an improved interfacial passivation will be required.     

Ecofriendly new nanocomposites coating formulation of zinc reinforced with calcium oxide nanoparticles synthesis from oyster shell

The zinc coating of mild undergoes rapid corrosion for a short period of time in harsh environments. This affects the durable life and overall performance of the zinc coatings. The electrochemical, oxidation, and wear performance, as well as the surface morphological properties of new nanocomposites coating formulations of zinc reinforced with calcium oxide nanoparticles, were studied in order to improve the corrosion and wear performance of zinc coatings. A current density of 1.5–2.0 A/cm² was used for the electrodeposition. The wear, oxidation, hardness, corrosion rate, and morphological properties were evaluated. The characterization of these composite coatings showed low wear rates and higher corrosion and oxidation resistance. At 1.5A/cm² current density, a 65.53% enhancement in the hardness values and 57.14% oxidation protection were obtained. The smaller crystallite size of the deposited sample is the main reason for the lower corrosion and wear resistance and higher hardness values obtained. It was established that waste oyster can be used for the electrodeposition of mild steel to enhance corrosion resistance and hardness values. CaOnp made from oyster shells has been shown to make mild steel more resistant to corrosion, wear, and oxidation.     

Surface interaction and corrosion inhibition of carbon steel in sulfuric acid using Petroselinum crispum extract

With the aid of the mass loss (ML) method, and a few electrochemical techniques [potentiodynamic polarization (PDP) and electrochemical impedance spectroscopy (EIS)], the inhibitory impact of Petroselinum crispum (PC) extract on C-steel corrosion in solutions of 1 M sulfuric acid was assessed. By employing Fourier-transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS) techniques, the C-steel surface morphology was investigated. The data showed that the solution of plant extract can be effectively utilized to inhibit C-steel corrosion in solutions of 1 M sulfuric acid. The effectiveness of the extract was enhanced by the higher extract dose and rising temperature. The apparent activation energy and the enthalpy of the dissolution process were determined and discussed. The presence of PC decreases the double-layer capacity from 493.1 to 107.3 μF cm⁻² and raises the charge transfer resistance in a solution of 1 M sulfuric acid from 43.39 to 287.7 Ω cm². PC is a mixed-type inhibitor, as demonstrated by PDP tests. The PC extract demonstrated the highest productivity for the C-steel protection up to 90.2% at 300 ppm from the extract, according with the PDP technique. The attained data indicated that PC extract was adsorbed chemically (ΔG^o_ads > 40 kJ mol⁻¹) onto the surface of the C-steel following the Temkin isotherm. The results of numerous tests appear to agree.     

Potential of zinc based-graphene oxide composite coatings on mild steel in acidic solution

This study introduces varying concentrations of graphene oxide (GO) as a filler into zinc chromate in forming composite coatings to improve the corrosion protection of mild steel. The purity of synthesized GO was inferred through the application of complementary characterization techniques, including FT-IR, XRD, Raman, SEM-EDX, and TEM analyses. GO doped zinc chromate coatings were deposited on the surface of mild steel through the brushing method. Electrochemical studies, i.e., electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization (PD) were conducted to elucidate the anticorrosion properties of the coated mild steel exposed to 0.5 ​M HCl solution. It was revealed that the highest anticorrosion protection was attained at low doping amount of 0.5% of GO with a corrosion rate of 0.036 mpy. Surface analyses revealed that incorporating GO into zinc chromate coating can effectively improve the anticorrosion properties and adhesion strength.     

Corrosion prevention of mild steel in acidic medium by 2-Pyrrolidin-1-yl-1,3-thiazole-5-carboxylic acid: Theoretical and experimental approach

The inhibition efficiency of 2-Pyrrolidin-1-yl-1,3-thiazole-5-carboxylic acid (PTCA) against mild steel (MS) corrosion was investigated in acidic solution by using quantum chemical calculations based on Density Functional Theory (DFT) method and electrochemical measurements. The electrochemical impedance spectroscopy (EIS), potentiodynamic, potential zero charge (pzc) analysis and electrochemical noise (EN) measurements at various concentrations (from 0.1 to 10 mM) and immersion times were utilized in experimental part. The surface analysis was achieved scanning electron microscope (SEM) and contact angle measurements in the absence and presence of 10 mM PTCA. According to DFT results, PTCA exhibited 3.737 eV band gap and 8.130 Debye dipole moment which were a signal of potentially convenient corrosion inhibitor properties. PTCA has a remarkable corrosion inhibition capability to mild steel, which inhibited both anodic and cathodic corrosion rates, relying on it's physically adsorption on the metal solution interface and protection ability was increased with increasing PTCA concentration. The obtained adsorption equilibrium constant was 11.11 × 10³ M^-1 and calculated standard free energy of adsorption was ?33.03 kJ mol^?1. The determined activation energy values were 55.58 kJ mol^?1 and 96.86 kJ mol^?1 in 0.5 M HCl in the absence and presence of 10 mM PTCA, respectively. PTCA demonstrated a strong inhibition efficiency of 98.3%, after 168 h immersion, according to the EIS results. As a consequently, we recommend that PTCA is a convenient inhibitor in 0.1 M HCl for mild steel protection against corrosion.     

WBE联合EIS技术研究缺陷涂层下金属腐蚀

用电化学阻抗谱(EIS)结合丝束电极(WBE)技术研究了缺陷涂层浸泡在3.5%(质量分数)NaCl溶液中的劣化过程.从浸泡开始到完好涂层鼓泡失效,缺陷涂层丝束电极阻抗响应一直是缺陷区电极腐蚀反应过程特征,而完好涂层的劣化过程和涂层下的腐蚀反应过程特征被"平均掉".根据电极表面的电流分布,结合阻抗谱技术实现了对表面任意局部阴极和阳极区阻抗测试.研究发现,浸泡开始时,缺陷涂层阴极电流和阳极电流均出现在缺陷区,随着腐蚀过程的发展,阳极电流仍然保持在缺陷区,但阴极电流逐渐向完好涂层下扩展.根据实验结果,对缺陷处和涂层下金属腐蚀反应发生发展的机理进行了深入讨论.     

Corrosion resistance of amorphous AlPO4 coating in salty atmospheres

The objective of the present study was to introduce a cost-effective and environmentally friendly coating to improve the corrosion resistance of the structures located in salt water. The coating solution, based on amorphous aluminum phosphate composition, was synthesized by sol–gel process and applied to AISI 304 stainless steel by dip coating technique. X-ray diffraction, scanning electron microscopy, and energy dispersive X-ray spectroscopy analyses were employed to investigate the phase composition and morphology of the coating. Corrosion behavior of the uncoated and coated samples was investigated using standard salt spray test, potentiodynamic polarization, and electrochemical impedance spectroscopy (EIS) in 3.5 wt.% NaCl solution. Salt spray test results for the bare substrate revealed a corrosion rate of six-time greater than that of the coated surface after 168 hr exposure time. Electrochemical test results declared that the amorphous AlPO₄ coating decreased the corrosion current density of the AISI 304 stainless steel by 10 orders of magnitude. Furthermore, according to the corresponding EIS measurements, the coated surface exhibited a superior anti-corrosion performance than uncoated sample. Overall, the results declared that the amorphous AlPO₄ coating could be a good choice for surface protection of stainless steel against electrochemical corrosion in salty environments.     

Curing mechanism,heat resistance,and anticorrosion properties of a furan/methyl phenyl silicone coating

A coating composed by methyl phenyl silicone resin (PSi) and furan resin (FR) was prepared, and its curing mechanism, heat resistance, and anticorrosion properties were investigated by Fourier transform infrared spectroscopy, thermogravimetric analysis, electrochemical test, and chemical resistance test. Aldol condensation reaction between FR and PSi occurred at below 200°C, and PSi underwent self‐multidehydrogenation at above 200°C. These curing reactions gave excellent thermal stability and anticorrosion properties. Compared with pure PSi, the blended containing lower than 20 wt% FR had better thermal properties, manifested as over 390°C of 5 wt% weight loss temperature and over 40% of char yield at 800°C. The adhesion property of cured blended system on the metal surface reached the first level which exceeded that of pure PSi coating (the third level). Furthermore, the corrosion resistances of coating in acid, alkali, and salt environments were all improved compared with those of monomeric polymer coating. The impedance of blended coating in 3.5% NaCl solution decreased with increasing FR content, which was 1.8 × 10⁶ Ω cm² when the FR content was 40%, being higher than that of pure PSi coating (7.12 × 10⁵ Ω cm²). This was mainly due to the formation of a cross‐linked network structure based on Si―O―C bond and the enhanced adhesion of cured blended coating. In addition, the surface roughness of cured blended coating was below 2.0 μm, which may have a positive effect on drag reduction in real applications.     

SiO2纳米粒子对溶胶凝胶涂层性能的影响

在高强钢表面制备了防护性溶胶凝胶涂层,并研究了不同浓度二氧化硅纳米粒子的加入对于涂层形貌、耐蚀性和硬度的影响。采用扫描电子显微镜(SEM)和电子能谱(EDS)观察了涂层的微观结构和成分;采用显微硬度计测试了涂层的硬度;采用电化学方法研究了二氧化硅纳米粒子的浓度对于涂层耐蚀性能的影响;采用傅里叶红外光谱研究涂层的化学结构,进而探讨了二氧化硅纳米粒子对于涂层的强化机理。结果显示涂层加入二氧化硅纳米粒子的最佳浓度为500 mg.L-1,此条件下的涂层表面均匀致密,有较高的硬度并且在3.5%NaCl溶液中体现出较好的耐蚀作用。纳米粒子在溶胶中反应形成活性羟基基团并与硅烷发生反应生成空间网状结构,从而强化涂层。