Nickel ferrite/zinc oxide nanocomposite: Investigating the photocatalytic and antibacterial properties

A facile strategy was used for the synthesis of nickel ferrite/zinc oxide (NiFe₂O_4/ZnO) nanocomposite via an ultra-sonication method and observed its recyclability and photostability with enhanced visible light-driven photocatalytic performance. The photo degradation activities of as-synthesized photocatalysts were investigated using various dyes including methylene blue, crystal violet and methyl orange under solar light irradiation. Prepared material degrades 49.2% methyl orange, 44.4% methyl blue and 41.3% crystal violet in 40 min. Further, the synergistic effect of nickel ferrite and zinc oxide can reduce the probability of recombination of charge carrier and boost the charge separation which leads to remarkable photocatalytic performance. Magnetic properties of nickel ferrite reduces the agglomeration of material and increases the recyclability. The NiFe₂O_4/ZnO nanocomposites also exhibited better antibacterial activity for Pseudomonas aeruginosa and Staphylococcus aureus, which shows that they can be used for both environmental and biological applications.     

Incorporation of MWCNTs into leaf-like CuO nanoplates for superior reversible Li-ion storage

CuO/MWCNT nanocomposite is prepared by a simple precipitation method. The MWCNTs are incorporated into the leaf-like CuO nanoplates and build up a network to connect the CuO nanoleaves. The as-prepared CuO/MWCNT exhibits superior reversible Li-ion storage, the capacity maintains 627 mAh g^? 1 at 60 mA g^? 1 even after 50 cycles. The improved capability is ascribed to the MWCNT network in the composite, which improves the electrical contact of CuO/CuO and CuO/current collector, facilitates the charge transfer on CuO/electrolyte interfaces, and compensates the volume change of CuO during cycling.     

Effects of CuO addition to anode on the electrochemical performances of cathode-supported solid oxide fuel cells

A cathode-supported electrolyte film was fabricated by tape casting and co-sintering techniques. (La_0.8Sr_0.2)_0.95MnO₃ (LSM95), LSM95/Zr_0.89Sc_0.1Ce_0.01O_2?x (SSZ), and SSZ were used as materials of cathode substrate, cathode active layer, and electrolyte, respectively. CuO–NiO–SSZ composite anode was deposited on SSZ surface by screen-printing and sintered at 1250 °C for 2 h. The effects of CuO addition to NiO–SSZ anode on the performance of cathode-supported SOFCs were investigated. CuO can effectively improve the sintering activity of NiO–SSZ. The assembled cells were electrochemically characterized with humidified H₂ as fuel and O₂ as oxidant. With 4 wt.% CuO addition, the ohmic resistance decreased from 3 to 0.46 Ω cm², and at the same time the polarization resistance decreased from 3.4 to 0.74 Ω cm². In comparison with the cell without CuO, the maximum power density at 850 °C increased from 0.054 to 0.446 W cm^?2 with 4 wt.% CuO addition.     

Electrophoretic deposition of ZnO photoanode for plastic dye-sensitized solar cells

Plastic dye-sensitized solar cells have been fabricated based on an organic dye (D 149) and ZnO photoanode prepared via room temperature electrophoretic deposition (EPD) to yield a conversion efficiency of 4.17% under 100 mW cm^?2 AM 1.5 illumination. Intensity modulated photocurrent spectroscopy analyses reveal that the fabricated ZnO electrodes have adequate interparticle connection, even in the absence of any post-treatment. This study demonstrates that EPD is a convenient method for photoanode fabrication and ZnO photoelectrodes obtained via EPD are promising for efficient plastic solar cells.     

Study of near infra red femtosecond laser induced particles using transmission electron microscopy and low pressure impaction: Implications for laser ablation–inductively coupled plasma-mass spectrometry analysis of natural monazite

The characteristics of infra red femtosecond laser-induced aerosols are studied for monazite (LREE, Th(PO₄)) ablation and correlations are established with inductively coupled plasma-mass spectrometry (ICP-MS) signals. Critical parameters are tested within wide ranges of values in order to cover the usual laser ablation -ICP-MS analysis conditions: pulse energy (0.15 < E₀ < 1 mJ/pulse), pulse width (60 < τ < 3000 fs), ablation time (t ≤ 10 min) and transport length (l ≤ 6.3 m). Transmission electron microscopy reveals that aerosols are made of agglomerates of ~ 10 nm particles and 20–300 nm phosphorus depleted condensed spherical particles. These structures are not affected by any laser ablation parameter. Particle counting is performed using electronic low pressure impaction. Small changes on particle size distribution are noticed. They may be induced either by a peak of ablation rate in the first 15 s at high fluence (larger particles) or the loss of small particles during transport. We found a positive correlation between I (ICP-MS mean signal intensity in cps) and N (particle density in cm^? 3) when varying E₀ and t, suggesting that N is controlled by the irradiance (P₀ in W·cm^? 2). Elemental ratio measurements show a steady state signal after the initial high ablation rate (mass load effect in the plasma torch) and before a late chemical fractionation, induced by poor extraction of bigger, early condensed spherical particles from the deepening crater. Such chemical fractionation effects remain within uncertainties, however. These effects can be limited by monitoring E₀ to shorten the initial transient state and delay the attainment of an unfavorable crater aspect ratio. Most adopted settings are for the first time deduced from aerosol characteristics, for infra red femtosecond laser ablation. A short transport (l < 4.0 m) limits the agglomeration of particles by collision process along the tube. Short τ is preferred because of higher P₀, yet no benefit is found on ICP-MS signal intensity under 200 fs. Under such pulse widths the increased particle production induces more agglomeration during transport, thereby resulting in higher mass load effects that reduce the ionization efficiency of the plasma torch. Thus, pulse energy must be set to get an optimal balance between the need for a high signal/background ratio and limitation of mass load effects in the plasma torch.     

Ultra-sensitive cholesterol biosensor based on low-temperature grown ZnO nanoparticles

A high-sensitive cholesterol amperometric biosensor based on the immobilization of cholesterol oxidase (ChOx) onto the ZnO nanoparticles has been fabricated which shows a very high and reproducible sensitivity of 23.7 μA mM^?1 cm^?2, detection limit (based on S/N ratio) 0.37 ± 0.02 nM, response time less than 5 s, linear range from 1.0 to 500.0 nM and correlation coefficient of R = 0.9975. A relatively low value of enzyme’s kinetic parameter (Michaelis–Menten constant) ～4.7 mM has been obtained which indicates the enhanced enzymatic affinity of ChOx to Cholesterol. To the best of our knowledge, this is the first report in which such a very high-sensitivity and low detection limit has been achieved for the cholesterol biosensor by using ZnO nanostructures modified electrodes.     

On the stability and properties of the polyacrylate/Na-MMT nanocomposite obtained by seeded emulsion polymerization

For high performance waterborne coatings usually polymer latexes with low emulsifier content are more preferred. Although polymer/clay nanocomposites offer improved properties, it is difficult to produce clay based nanocomposite latexes containing low emulsifier due to the stabilization problems especially caused by organoclays. Present study deals with the preparation of a tBA/BA/MAA ternary copolymer/clay nanocomposite containing 3 wt.% sodium montmorillonite (Na⁺-MMT) via seeded emulsion polymerization. Experimentally it was observed that even the usage of hydrophilic clay caused stabilization problem and a certain amount of emulsifier (>1 wt.%) was necessary to obtain stable latexes. In addition, the usage of a low molecular weight water soluble polymer as steric barrier was found to increase the stability of system. Obtained nanocomposite latex showed fine particle size diameter (127 nm) and very narrow size distribution (PDI = 0.06). The WAXD and TEM investigations indicated that a mostly exfoliated nanocomposite was obtained. Thermal analyses (DSC, DMTA and TGA) showed that there was no change at T_g of the copolymer while very high improvement was obtained for elastic modulus and a slight increase in thermal stability. According to the rheological measurements, the nanocomposite latex showed a higher low shear viscosity, a stronger shear thinning behavior and an improved physical stability in comparison to the reference latex.     

Arrayed CNx NT–RuO2 nanocomposites directly grown on Ti-buffered Si substrate for supercapacitor applications

Significant enhancement in supercapacitor performance has been achieved via a new RuO₂ nanocomposite materials prepared by direct ruthenium sputtering on arrayed multi-walled carbon nanotubes supported by Ti-buffered Si wafer. XPS, HRTEM and SAED analyses reveal that as-prepared nanoparticles have a crystalline Ru metal core with RuO₂ oxide coating. The nanocomposites convert to RuO₂–CN_x NTs with subsequent electrochemical cycling. At present, well-dispersed and strongly adhered RuO₂ NPs have been densely populated on CN_x NTs to obtain the overall specific capacitance (1380 F/g-RuO₂), charging–discharging rate (up to 600 mV/s) and operation stability (5000 cycles). Thus, RuO₂–CN_x NTs nanocomposites would make a promising candidate for use in next-generation high efficiency miniaturized supercapacitors directly fabricated on Si substrate.     

Optical and electrical conducting properties of Polyaniline/Tin oxide nanocomposite

Polyaniline(PANI)/Tin oxide (SnO₂) hybrid nanocomposite with a diameter 20–30 nm was prepared by co-precipitation process of SnO₂ through in situ chemical polymerization of aniline using ammonium persulphate as an oxidizing agent. The resulting nanocomposite material was characterized by different techniques, such as X-ray diffraction (XRD), Transmission Electron Microscopy (TEM), Fourier Transform Infrared spectroscopy (FT-IR) and Ultraviolet–Visible spectroscopy (UV–Vis), which offered the information about the chemical structure of polymer, whereas electron microscopy images provided information regarding the morphology of the nanocomposite materials and the distribution of the metal particles in the nanocomposite material. SEM observation showed that the prepared SnO₂ nanoparticles were uniformly dispersed and highly stabilized throughout the macromolecular chain that formed a uniform metal-polymer nanocomposite material. UV–Vis absorption spectra of PANI/SnO₂ nanocomposites were studied to explore the optical behavior after doping of nanoparticles into PANI matrix. The incorporation of SnO₂ nanoparticles gives rise to the red shift of π–π¹ transition of polyaniline. Thermal stability of PANI and PANI/SnO₂ nanocomposite was investigated by thermogravimetric analysis (TGA). PANI/SnO₂ nanocomposite observed maximum conductivity (6.4 × 10^?3 scm^?1) was found 9 wt% loading of PANI in SnO₂.     

Fabrication of super-macroporous nanocomposites by deposition of carbon nanotubes onto polymer cryogels

Electrically conducting super-macroporous carbon nanotube/polymer cryogel nanocomposites were fabricated by a novel approach based on deposition of carbon nanotubes (CNTs) onto the inner surface of pre-formed cryogels assisted by cryogenic treatment. Stable aqueous dispersions of multi-walled and single-walled carbon nanotubes were firstly obtained by non-covalent modification of pristine nanotubes with either pyrene containing polydimethylacrylamide or poly(ethylene oxide)₂₆-b-poly(propylene oxide)₄₀-b-poly(ethylene oxide)₂₆ copolymers and, then, exploited for the preparation of nanocomposites. The mechanical and electrical properties of nanocomposite materials were measured and compared to similar materials prepared by established method. The novel approach provided super-macroporous nanocomposites with high electrical conductivity (>10^?2 S/m) at much lower nanotube content (0.12 wt.%).     

Study of CuZnMOx oxides (M = Al,Zr, Ce,CeZr) for the catalytic hydrogenation of CO2 into methanol

CuO–ZnO–Al₂O₃ catalysts were synthesized by two methods, sol–gel and co-precipitation syntheses. Al₂O₃ was then substituted with other supports, such as ZrO₂, CeO₂ and CeO₂–ZrO₂ in order to have a better understanding of the support's effect. These catalysts containing 30 wt% of Cu were then tested for CO₂ hydrogenation into methanol. The effect of reaction temperature and GHSV on the catalytic behaviour was also investigated. The best results were obtained with a 30 CuO–ZnO–ZrO₂ catalyst synthesized by co-precipitation and calcined at 400 °C. This catalyst presents a good CO₂ conversion rate (23%) with 33% of methanol selectivity, leading to a methanol productivity of 331 g_MeOH.kg_cata⁻¹·h⁻¹ at 280 °C under 50 bar and a GHSV of 10,000 h⁻¹.     

Synthesis,characterization and antibacterial properties of a novel nanocomposite based on polyaniline/polyvinyl alcohol/Ag

In this study, a novel nanocomposite based on polyaniline/polyvinyl alcohol/Ag (PANI/PVA/Ag) has been successfully synthesized. The chemical reduction method was used to produce Ag nanoparticle colloidal solution from Ag⁺ ions. The polymerization of aniline occurred in situ for the preparation of polyaniline (PANI) in the presence of ammonium persulfate. With exposure to Ag nanoparticles on the PANI/PVA composite, a new nanocomposite was obtained. The morphology and particle size of the novel nanocomposite was studied by scanning electron microscopy (SEM), X-ray diffraction (XRD), and Fourier transform infrared (FT-IR) analyses. According to XRD analysis, the size of nanoparticles was found to be in the range of 10–17 nm. SEM images showed the favored shape of nanoparticles as triangle which is a benign shape for antibacterial analysis. The antibacterial activity of the obtained nanocomposite was also evaluated against Gram positive bacteria Staphylococcus aureus (Staph. aureus) and Gram negative Escherichia coli (E. coli) using the paper disk diffusion method. The antibacterial study showed that the PANI/PVA composite did not have a very good antibacterial activity but PANI/PVA/Ag nanocomposites were found to be effective against two bacteria.     

In vitro cytotoxicity against K562 tumor cell line,antibacterial, antioxidant,antifungal and catalytic activities of biosynthesized silver nanoparticles using Sophora pachycarpa extract

In the present study, we demonstrate the green synthesis of silver nanoparticles using Sophora pachycarpa extract (S. pachycarpa; SPE) as capping, reducing, and stabilizing agents. The biosynthesized silver nanoparticles (SPE-AgNPs) were tested for catalytic, antibacterial, antifungal, antioxidant, and anti-cancer activities. The affecting parameters (the concentration of silver nitrate, the temperature of the reaction, and time of reaction) on the synthesis process were optimized. The biosynthesized SPE-AgNPs were studied by X-Ray diffraction (XRD), transmission electron microscopy (TEM), field emission scanning electron microscopy (FESEM), dynamic light scattering (DLS), energy-dispersive X-ray spectroscopy (EDS) and Fourier-transform infrared spectroscopy (FT-IR). The FESEM and TEM results revealed spherical and oval-like morphology with sizes ranging from 30 to 40 nm. Photocatalytic performance experiments of SPE-AgNPs were determined by the rapid degradation of the eriochrome black T (EBT) and methylene blue (MB) under sunlight and UV irradiations. The results showed that SPE-AgNPs degraded more than 90% and 80% of both dyes under UV and sunlight irradiations, respectively. In addition, the SPE-AgNPs exhibited good antibacterial and antifungal properties against S. aureus, S. epidermidis, P. aeruginosa, E. coli, K. pneumoniae, E. faecalis, and C. albicans with MIC values of 6.25, 6.25, 0.78, 0.39, 0.78, 1.56 and 0.78 µg/ml. The green synthesized SPE-AgNPs were found to inhibit the activity of DPPH free radicals efficiently. Eventually, the SPE-AgNPs exhibited significant in vitro cytotoxicity against K562 tumor cell line (IC50 = 19.5 µg/ml). All these studies indicated that AgNPs synthesized using S. pachycarpa extract have applications in the environmental and biomedical fields.     

Biosynthesized CuO nano-platelets: Physical properties & enhanced thermal conductivity nanofluidics

This contribution reports for the first time, room temperature biosynthesis of p-type CuO nanoparticles carried out using Callistemon viminalis’ flower extracts as a chelating agent in a process that is entirely green. Room temperature X-ray diffraction, attenuated IR total reflection spectroscopy, X-ray photoelectron and Raman spectroscopy investigations confirmed the formation of single phase Tenorite bcc monoclinic CuO nanocrystals post annealing in air, at 500 °C. Photoluminescence spectroscopy with UV emissions at 356 nm (3.47 eV) and broad visible emissions at 418 nm, 561 nm, and 664 nm, support the formation in air, at 200 °C, of CuO nanoparticles with high surface-to-volume ratios and defects. As a direct application, the biosynthesized CuO nanoplatelet-containing powder dispersed in de-ionized water showed an enhancement of the thermal conductivity from 6% to 34% and a significant stability of the PVP stabilized CuO-water nanofluid.     

Size-controllable synthesis of spherical ZnO nanoparticles: Size- and concentration-dependent resonant light scattering

A new and simple direct precipitation method assisted with ultrasonic agitation was proposed for the preparation of spherical ZnO nanoparticles. The size of the ZnO nanoparticles, 10 nm to 85 nm, was tuned through controlling the calcination temperature and changing the ratio of the reactants. The resonant light scattering (RLS) of the ZnO nanoparticles dispersed/suspended in aqueous solution of Triton X-100 was studied under room temperature. It was found that the ZnO nanoparticles of different size or concentration all have a characteristic RLS peak at 387 nm. Under optimal conditions, the RLS intensity was proportional to the ZnO concentration in the range of 7.3 × 10^?8–1 × 10^?4 mol L^?1, while the cubic root of the RLS intensity was found to be proportional to the size of ZnO nanoparticles. Further, the quantitative relationship of the size of the ZnO nanoparticles versus the calcination temperature was derived, and this could be used to forecast/control the nano-size in the nano-ZnO preparation.     

Chemical composition,antibacterial and antioxidant activities of essential oils from leaves of three Melaleuca species of Pakistani flora

This study presents essential oil composition of three Melaleuca species namely, Melaleuca bracteata F. Muell, Melaleuca fulgens R. Br. subsp. steedmanii and Melaleuca leucadendron (L.) L. collected from different regions of Pakistan. The chemical composition of essential oils was analyzed by GC-FID and GC–MS. Eugenol methyl ether was identified as a principal component in M. bracteata (82.3%), M. fulgens (87.8%) and M. leucadendron (95.4%) oils. In vitro antibacterial studies were done by agar well diffusion and microdilution method and the tested essential oils exhibited bacteriostatic and bactericidal effects against the tested foodborne pathogens at 4–8 µg/ml. Time kill assay showed significant bactericidal effect of oils for four weeks. The antioxidant potential was assessed by free radical scavenging activity and reducing power assay. The oils showed strong antioxidant activity with approximately 89.0–89.5% inhibition of 2,2-diphenyl-1-picrylhydrazyl radical and ferric reducing power in the range of 1.94 ± 0.007–2.04 ± 0.04% at 100 µg/ml.     

Mechanoelectrochemical synthesis of porous Ti-based nanocomposite biomaterials

In this work we have synthesized a new class of nanocomposites based on Ti with the addition of hydroxyapatite (HA) and glass 45S5. The nanocomposites were prepared by mechanical alloying of the pure microcrystalline Ti powders with different amount of ceramics. The powder mixture was milled up to 48 h, pressed and sintered, which resulted in nanocomposite structure with the grain size of about 20–36 nm. The ultra low grain size structure improves mechanical properties of the implants in comparison to commonly used microcrystalline Ti-based implants. For example, the hardness of the Ti-HA nanocomposites reaches a value of 1500 HV and is five times greater than the microcrystalline Ti.To improve bonding of the implants with human tissue, the implants were electrochemically etched in 1 M H₃PO₄ + 2–10% HF electrolyte at 10 V vs. OCP for times up to 60 min. The treatment results in highly porous surface covered with Ti-oxide. The nanocrystalline structure is very useful during etching, due to the easy access of the electrolyte to the large volume of the grain boundaries. The nanocomposites with modified surface show very good corrosion resistance in Ringer’s solution.     

Synthesis of a PEBAX-1074/ZnO nanocomposite membrane with improved CO_2 separation performance

In this investigation, polymeric nanocomposite membranes(PNMs) were prepared via incorporating zinc oxide(ZnO) into poly(ether-block-amide)(PEBAX-1074) polymer matrix with different loadings. The neat membrane and nanocomposite membranes were prepared via solution casting and solution blending methods, respectively. The fabricated membranes were characterized by field emission scanning electron microscopy(FESEM) to survey cross-sectional morphologies and thermal gravimetric analysis(TGA)to study thermal stability. Fourier transform infrared(FT-IR) and X-ray diffraction(XRD) analyses were also employed to identify variations of the chemical bonds and crystal structure of the membranes, respectively. Permeation of pure gases, CO_2, CH_4 and N_2 through the prepared neat and nanocomposite membranes was studied at pressures of 3–18 bar and temperature of 25 °C. The obtained results showed that the fabricated nanocomposite membranes exhibit better separation performance compared to the neat PEBAX membrane in terms of both permeability and selectivity. As an example, at temperature of 25 °C and pressure of 3 bar, CO_2 permeability, ideal CO_2/CH_4 and CO_2/N_2 selectivity values for the neat PEBAX membrane are 110.67 Barrer, 11.09 and 50.08, respectively, while those values are 152.27 Barrer,13.52 and 62.15 for PEBAX/ZnO nanocomposite membrane containing 8 wt% ZnO.     

Low temperature heat capacity of bulk and nanophase ZnO and Zn1−xCoxO wurtzite phases

The low temperature heat capacity of the ZnO–CoO solid solution system was measured from 2 to 300 K using the heat capacity option of a Quantum Design Physical Property Measurement System (PPMS). The thermodynamic functions in this temperature range were derived by curve fitting. The standard entropies of bulk ZnO and bulk ZnO–CoO (wurtzite, 18 mol% CoO) at T = 298.15 K were calculated to be (43.1 ± 0.4) J · mol⁻¹ · K⁻¹ and (45.2 ± 0.5) J · mol⁻¹ · K⁻¹, respectively. The surface entropy of ZnO was evaluated to be (0.02 ± 0.01) mJ · K⁻¹ · m⁻², which is essentially zero. No sharp magnetic transitions were observed in the solid solution samples. The nanophase solid solution, 12 mol% CoO, appears to bind H₂O on its surface more strongly than ZnO.     

Formation of nano-crystalline quartz crystals from ZnO/MgO/Al2O3/TiO2/ZrO2/SiO2 glasses

Glasses with the compositions 50.9 SiO₂ · 20.8 Al₂O₃ · (20.8 ? x) MgO· × ZnO · 3.7 TiO₂ · 3.7 ZrO₂ with x = 0, 2.3, 4.6 and 9.3 were annealed at temperatures in the range from 850 to 1100 °C. Depending on temperature, high- or low-quartz solid solutions, magnesium aluminosilicate, mullit and spinel precipitated. These glass–ceramics exhibit excellent mechanical properties and are potential candidates for applications in micromechanics or as hard disc substrate.The larger the ZnO concentration, the lower is the glass transition temperature. Also microhardnesses and Young’s moduli increased with increasing ZnO concentration. The nucleation temperature was of minor importance. To achieve good mechanical properties, the initially formed high-quartz phase must transform to the corresponding low-quartz phase. This occurs if the quartz phase contains only minor MgO or ZnO concentrations, which can be achieved by increasing the annealing times or temperature. Then MgO, ZnO and Al₂O₃ occur as separate spinel or gahnite phase.