Adsorption of cationic methylene blue dye using microwave-assisted activated carbon derived from acacia wood: Optimization and batch studies

This study assesses the performance of optimized acacia wood-based activated carbon (AWAC) as an adsorbent for methylene blue (MB) dye removal in aqueous solution. AWAC was prepared via a physicochemical activation process that consists of potassium hydroxide (KOH) treatment, followed by carbon dioxide (CO₂) gasification under microwave heating. By using response surface methodology (RSM), the optimum preparation conditions of radiation power, radiation time, and KOH-impregnation ratio (IR) were determined to be 360 W, 4.50 min, and 0.90 g/g respectively, which resulted in 81.20 mg/g of MB dye removal and 27.96% of AWAC’s yield. Radiation power and IR had a major effect on MB dye removal while radiation power and radiation time caused the greatest impact on AWAC’s yield. BET surface area, mesopore surface area, and pore volume of optimized AWAC were found to be 1045.56 m²/g, 689.77 m²/g, and 0.54 cm³/g, respectively. Adsorption of MB onto AWAC followed Langmuir and pseudo-second order for isotherm and kinetic studies respectively, with a Langmuir monolayer adsorption capacity of 338.29 mg/g. Mechanism studies revealed that the adsorption process was controlled by film diffusion mechanism and indicated to be thermodynamically exothermic in nature.     

Optimization and mass transfer simulation of remazol brilliant blue R dye adsorption onto meranti wood based activated carbon

Remazol brilliant blue R dye (RBBR) brings toxicity to living organisms once it enters the environment. This study utilized response surface methodology (RSM) and Polymath software for optimization and mass transfer simulation purposes, respectively. RSM revealed that the optimum preparation conditions of meranti wood-based activated carbon (MWAC) were 441 W, 5.76 min, and 1.35 g/g for radiation power, radiation time, and KOH:char impregnation ratio (IR), respectively, which translated into 86.39 mg/g of RBBR uptakes and 31.94 % of MWAC’s yield. The simulation study predicted the mass transfer rate, r_m to be 112.20 to 1007.50 s^?1 and the adsorption rate, k₁ to be 3.96 to 4.34 h^?1. The developed model predicted the adsorption surface area, a_m to be 790.04 m²/g and this value is highly accurate as compared to the actual mesopores surface area of 825.58 m²/g. Mechanism analysis divulged that the interaction that occurred between RBBR molecules and MWAC’s surface were hydrogen bond (methylene and alkyne), dipole–dipole force (alkyl carbonate, terminal alkyne, and methoxy), and ion–dipole force (primary amine). The isotherm and kinetic studies found that the adsorption data obeyed the Freundlich model and pseudo-first-order (PFO) model the best, respectively. The Langmuir maximum adsorption capacity, Q_m was computed to be 327.33 mg/g. Thermodynamic parameters were calculated to be ?4.06 kJ mol^?1, 0.06 kJ mol^?1 K^?1, –22.69 kJ mol^?1, and 16.03 kJ mol^?1 for ΔH°, ΔS°, ΔG°, and E_a, respectively, which signified the adsorption process studied was exothermic, spontaneous and governed by physisorption.     

A novel study on synthesis of egg shell based activated carbon for degradation of methylene blue via photocatalysis

Egg shell-based activated carbon was successfully synthesized by the simple chemical activation process. Orthophosphoric acid and sodium hydroxide used as an activation agent. XRD pattern reveals the hexagonal structure of activated carbon. The functional group presents in activated carbon was identified using FT-IR spectroscopy. SEM images show irregular shapes of carbon. The photocatalytic performance of investigated activated carbon by illuminating methylene blue dye under UV–Visible irradiations. Photocatalytic activity of activated carbon results maximum degradation efficiency of 83%. Adsorption efficiency have been increased with respect of time for degradation of dye. Free radicals and superoxide’s play a significant role is decolourization of methylene blue. Photocatalytic activity of activated carbon synthesized by Orthophosphoric acid results shows the high degradation efficiency when compared to NaOH.     

Valorization of two waste streams into activated carbon and studying its adsorption kinetics,equilibrium isotherms and thermodynamics for methylene blue removal

Wastes must be managed properly to avoid negative impacts that may result. Open burning of waste causes air pollution which is particularly hazardous. Flies, mosquitoes and rats are major problems in poorly managed surroundings. Uncollected wastes often cause unsanitary conditions and hinder the efforts to keep streets and open spaces in a clean and attractive condition. During final disposal methane is generated, it is much more effective than carbon dioxide as a greenhouse gas, leading to climate change. Therefore, this study describes the possible valorization of two waste streams into activated carbon (AC) with added value due to copyrolysis. High efficiency activated carbon was prepared by the copyrolysis of palm stem waste and lubricating oil waste. The effects of the lubricating oil waste to palm stem ratio and the carbonization temperature on the yield and adsorption capacity of the activated carbon were investigated. The results indicated that the carbon yield depended strongly on both the carbonization temperature and the lubricating oil to palm stem ratio. The efficiency of the adsorption of methylene blue (MB) onto the prepared carbons increased when the lubricating oil to palm stem ratio increased due to synergistic effect. The effects of pH, contact time, and the initial adsorbate concentration on the adsorption of methylene blue were investigated. The maximum adsorption capacity (128.89 mg/g) of MB occurred at pH 8.0. The MB adsorption kinetics were analyzed using pseudo-first order, pseudo-second order and intraparticle diffusion kinetic models. The results indicated that the adsorption of MB onto activated carbon is best described using a second order kinetic model. Adsorption data are well fitted with Langmuir and Freundlich isotherms. The thermodynamic parameters; ΔG°, ΔH° and ΔS° indicate that the adsorption is spontaneous and endothermic.     

Exploration of biomass waste as low cost adsorbents for removal of methylene blue dye: A review

Biomass waste, which is abundantly available has been studied as low cost biosorbent for dye sequestration from waste water. The present review reports on recent development for remediation of methylene blue dye by agricultural waste and fruit peel waste material. The aim of this study was to revise latest literature in the field of dye adsorption and discuss the dye adsorption capacity of different types of adsorbents. The activated carbon prepared from several types of biomass waste material enhances the adsorption efficiency after modification. The variety of activating agents, method of activation, characterization of biosorbent material like SEM, EDAX, BET surface area and FTIR analysis has been explored in the present review. The dye adsorption factors such as effect of pH, agitation time, temperature, adsorbate and adsorbent dose were discussed. The detailed investigation on applicability of isotherm model, kinetic model and thermodynamic parameters has also been presented. The adsorption kinetics and adsorption isotherm model focus on selectivity of adsorbent. Adsorption mechanism, Influence of surface area, influence of pH_pzc and comparative study of biomass waste adsorbent with other adsorbents have been carried out. The use of biomass waste adsorbents is economically feasible, environmental healthy and found to have outstanding removal capacity of dyes.     

Review on recent advances of carbon based adsorbent for methylene blue removal from waste water

The growth in textile and printing industries proven detrimental to the aquatic environment as the industrial waste containing dye seeped into the ecosystem. A high concentration of dye in water possess negative impacts on water ecosystem and harmful to human health. Removal of methylene blue (MB) dye from industrial waste via adsorption pathway has been widely investigated that promised high efficiency of MB removal. This review will summarize researches published from 2008 to 2019 on the removal of MB using carbon adsorbent with focus will be given on the synthesis and modification of carbon-based materials, and the structural properties influencing the performance of MB adsorption. Summary on the type of material used for the synthesis of carbon materials (activated carbon and biochar) will be included from utilization of the naturally occurring carbon sources such as polymers, biomasses and biowastes, and also sucrose and hydrocarbon gases. Modification of carbon materials such as chemical activation and physical activation; surface grafting to form functionalized surfaces; deposition with metal and magnetic nanoparticles via impregnation; and manufacturing of carbon composites will be discussed on the effects to promote MB adsorption and desorption. Another type of carbon adsorbents such as porous carbon; graphitic carbons including graphite, graphene, graphene oxide, and carbon nitride (g-C₃N₄); and finally nanocarbon in the form of nanotube, nanorod and nanofiber; will be included in the review with details on the synthesis method and the correlation between structural properties and adsorption activity. The regeneration process to increase the life cycle of carbon adsorbent will also be discussed based on two regeneration pathway i.e. a thermal degradation and desorption on MB. Finally the thermodynamics, kinetics, and the adsorption models of MB on carbon adsorbent will be discussed in this review.     

Mechanistic insights into methylene blue removal via olive stone-activated carbon: A study on surface porosity and characterization

Global attention is increasingly focused on the adverse health and environmental impacts of textile dyes, marking the necessity for effective and sustainable dye remediation strategies in industrial wastewater. This study introduces a novel, eco-friendly activated carbon produced from olive stones (OLS), a readily available by-product of the olive oil industry. The OLS was chemically activated with H₃PO₄ and KOH, creating two materials: OLS-P and OLS-K, respectively. These were then utilized as cost-effective adsorbents for the removal of methylene blue (MB) dye. The activated materials were characterized via X-ray diffraction (XRD), Fourier transform infra-red spectroscopy (FTIR), iodine number, and pHpzc analysis, with the zero-point charge determined as approximately pH 1 for OLS-P and pH 8 for OLS-K. Batch adsorption experiments conducted at various temperatures revealed that adsorption process followed the pseudo-second-order kinetic model and the Langmuir isotherm model. Temperature was found to significantly impact adsorption performance, with OLS-K demonstrating a substantial increase in adsorption capacity (q_e) from 6.27 mg/g at 23˚C to 94.7 mg/g at 32 ˚C. Conversely, OLS-P displayed a decrease in q_e from 16.78 mg/g at 23 ˚C to 3.67 mg/g at 32 ˚C as temperature increased. The study highlights the potential of KOH-treated olive stones as a promising, cost-efficient adsorbent for methylene blue remediation from wastewater.     

Removal of cationic methylene blue and malachite green dyes from aqueous solution by waste materials of Daucus carota

In present study adsorption capacity of waste materials of Daucus carota plant (carrot stem powder: CSP and carrot leaves powder: CLP) was explored for the removal of methylene blue (MB) malachite green (MG) dye from water. The morphology and functional groups present were investigated by scanning electron microscope (SEM) and Fourier transform infrared (FTIR) spectroscopy. The operating variables studied were pH, adsorbent dose, ionic strength, initial dye concentration, contact time and temperature. Equilibrium data were analysed using Langmuir and Freundlich isotherm models and monolayer adsorption capacity of adsorbents were calculated. Kinetic data were studied using pseudo-first and pseudo-second order kinetic models and the mechanism of adsorption was described by intraparticle diffusion model.Various thermodynamic parameters such as enthalpy of adsorption ΔH°, free energy change ΔG° and entropy ΔS° were estimated. Negative value of ΔH° and negative values of ΔG° showed that the adsorption process was exothermic and spontaneous. Negative value of entropy ΔS° showed the decreased randomness at the solid–liquid interface during the adsorption of MB and MG onto CSP and CLP.     

Synthesis of activated carbon foams with high specific surface area using polyurethane elastomer templates for effective removal of methylene blue

Carbon foams have gained significant attention due to their tuneable properties that enable a wide range of applications including catalysis, energy storage and wastewater treatment. Novel synthesis pathways enable novel applications via yielding complex, hierarchical material structure. In this work, activated carbon foams (ACFs) were produced from waste polyurethane elastomer templates using different synthesis pathways, including a novel one-step method. Uniquely, the produced foams exhibited complex structure and contained carbon microspheres. The ACFs were synthesized by impregnating the elastomers in an acidified sucrose solution followed by direct activation using CO₂ at 1000 ℃. Different pyrolysis and activation conditions were investigated. The ACFs were characterized by a high specific surface area (S_BET) of 2172 m²/g and an enhanced pore volume of 1.08 cm³/g. Computer tomography and morphological studies revealed an inhomogeneous porous structure and the presence of numerous carbon spheres of varying sizes embedded in the porous network of the three-dimensional carbon foam. X-ray diffraction (XRD) and Raman spectroscopy indicated that the obtained carbon foam was amorphous and of turbostratic structure. Moreover, the activation process enhanced the surface of the carbon foam, making it more hydrophilic via altering pore size distribution and introducing oxygen functional groups. In equilibrium, the adsorption of methylene blue on ACF followed the Langmuir isotherm model with a maximum adsorption capacity of 592 mg/g. Based on these results, the produced ACFs have potential applications as adsorbents, catalyst support and electrode material in energy storage systems.     

Microwave assisted preparation of efficient activated carbon from grapevine rhytidome for the removal of methyl violet from aqueous solution

Grapevine rhytidome (the outer layer of bark on trunk), as an abundant and low-cost precursor, was used to prepare granular activated carbon with high surface area for the removal of methyl violet from aqueous solution. Microwave heating source was used to reduce the treatment time and energy consumption. To optimize the preparation, the effects of the different parameters, such as phosphoric acid concentration, acid/precursor weight ratio, impregnation time, microwave power, radiation time, and oven heating time on the ability of the samples for removal of methyl violet were studied. The obtained activated carbon was characterized by N₂ adsorption/desorption, SAXS, TEM and SEM methods. The adsorption of methyl violet onto the activated carbon was studied from both equilibrium and kinetic point of view and the results were compared with the commercial granular activated carbon. The rate of adsorption onto the prepared activated carbon was faster than commercial activated carbon. Different kinetic models were used to analyze the experimental kinetic data. The obtained activated carbon showed higher adsorption capacity (more than twice) for the adsorption of methyl violet in comparison with the commercial one. The equilibrium data were analyzed using different isotherm models. Adsorption was found to be maximum in the pH range 7-9.     

Sterculia foetida fruit shell based activated carbon for the effective removal of industrial effluents

In this work, Sterculia foetida fruit shells were used for the preparation of activated carbon and utilized for the removal of industrial effluent methylene blue is described. The carbon materials were prepared by washing the shells with water, dried in sunlight and subjected to heating at 700 ​°C in a muffle furnace to get the carbon material. This is divided into three portions, one is used as pristine and two portions were subjected to physical activation using steam and chemical activation using K₂CO₃. The impurities were removed by treatment with NaOH (0.1 ​M) and subsequently with HCl (0.1 M). Turbostatic structure was determined by XRD and the specific surface area was determined using BET showed 4, 1017 and 596 ​m²/g as the surface areas. Using these activated carbon materials, we have achieved 93% removal of methylene blue, found in industrial effluents.     

Super-assembled highly compressible and flexible cellulose aerogels for methylene blue removal from water

Physical adsorption is a common method to solve the contamination of methylene blue in dyeing wastewater. As a kind of adsorption material, cellulose aerogels with high porosity and surface areas have great potential application in methylene blue removal. However, the week hydrogen bonding between cellulose nanofibers making the cellulose aerogels with the poor mechanical properties and can be easily destroyed during adsorption. Hence, the preparation of cellulose aerogels with high mechanical strength is still a great challenge. Here, we report a robust super-assembly strategy to fabricate cellulose aerogels by combining cellulose nanofibers with PVA and M-K10. The resulting cellulose aerogels not only has a robust chemically cross-linked network, but also has strong H-bonds, which greatly enhance the mechanical properties. The resulting cellulose aerogels possess a low density of 19.32 mg/cm3.Furthermore, the cellulose aerogel shows 93% shape recovery under 60% strain(9.5 k Pa under 60% strain)after 100 cycles, showing excellent mechanical property. The adsorption capacity of cellulose aerogel to methylene blue solution of 20 mg/L is 2.28 mg/g and the adsorption kinetics and adsorption isotherms have also been studied. Pseudo-second-order kinetic model and Freundlich isotherm model are more acceptable for indicating the adsorption process of methylene blue on the cellulose aerogel. Thus, this compressible and durable cellulose aerogel is a very prospective material for dyeing wastewater cleanup.     

Facile preparation of hierarchically porous carbon using diatomite as both template and catalyst and methylene blue adsorption of carbon products

Hierarchically porous carbons were prepared using a facile preparation method in which diatomite was utilized as both template and catalyst. The porous structures of the carbon products and their formation mechanisms were investigated. The macroporosity and microporosity of the diatomite-templated carbons were derived from replication of diatom shell and structure-reconfiguration of the carbon film, respectively. The macroporosity of carbons was strongly dependent on the original morphology of the diatomite template. The macroporous structure composed of carbon plates connected by the pillar- and tube-like macropores resulted from the replication of the central and edge pores of the diatom shells with disk-shaped morphology, respectively. And another macroporous carbon tubes were also replicated from canoe-shaped diatom shells. The acidity of diatomite dramatically affected the porosity of the carbons, more acid sites of diatomite template resulted in higher surface area and pore volume of the carbon products. The diatomite-templated carbons exhibited higher adsorption capacity for methylene blue than the commercial activated carbon (CAC), although the specific surface area was much smaller than that of CAC, due to the hierarchical porosity of diatomite-templated carbons. And the carbons were readily reclaimed and regenerated.     

Comparative study for the removal of methylene blue via adsorption and photocatalytic degradation

Physically and chemically activated carbons were prepared from date pits and olive stones. Titania and WO(x)-TiO(2)/MCM-41 were prepared as photoactive catalysts. Surface characterizations were investigated from ash content, pH, base neutralization capacities and FT-IR techniques. The textural characteristics, namely specific surface area (S(BET)) and pore texture, were determined from low temperature adsorption of N(2) at 77 K. The decolorization of aqueous solution of methylene blue was performed by means of two alternative methods. Steam-activated carbons own higher surface area compared with ZnCl(2)-activated carbons, and the micropore surface area represents the major contribution of the total area. Steam-activated carbons were the most efficient decolorizing adsorbents owing to its higher surface area, total pore volume and the basic nature of the surface. The calculated values of DeltaG(0), DeltaH(0) and DeltaS(0) indicate the spontaneous behavior of adsorption. The photocatalytic degradation is more convenient method in decolorizing of methylene blue compared with the adsorption process onto activated carbons.     

Functionalized electrospun carbon nanofibers for removal of cationic dye

Electrospun carbon nanofibers (ECNFs) have attracted significant attention in recent years as relatively inexpensive alternative to carbon nanotubes for adsorption organic pollutants. In this study, ECNFs were fabricated from polyacrylonitrile (PAN) using an electrospinning technique, followed by carbonization and oxidation via treatment with a H₂SO₄/HNO₃ mixture. The prepared oxidized electrospun carbon nanofibers (O-ECNFs) were characterized using scanning and transmission electron microscopy (SEM and TEM), Fourier transform infrared (FT-IR), Brunauer-Emmett-Teller (BET), X-ray diffraction (XRD), and thermogravimetric analysis (TGA). The O-ECNFs were used as nano-adsorbents for the adsorption of methylene blue (MB) from aqueous solution. The adsorption of MB by the O-ECNFs was studied as a function of pH, time, adsorbent dosage, MB concentration, and temperature. ECNF functionalization enhanced the adsorption capacity towards MB dye compared pristine ECNFs. Detailed analysis of the adsorption kinetics showed that the adsorption process followed a pseudo-second-order model. The adsorption isotherm was best fit by the Langmuir model. The thermodynamic results showed that MB adsorption onto the O-ECNFs was endothermic and spontaneous.     

Optimization of preparation conditions for activated carbon from palm oil fronds using response surface methodology on removal of pesticides from aqueous solution

Palm oil fronds were used to prepare activated carbon using the physiochemical activation method, which consisted of potassium hydroxide (KOH) treatment and carbon dioxide (CO₂) gasification. The effects of variable parameters activation temperature, activation time and chemical impregnation ratios (KOH: char by weight) on the preparation of the activated carbon and for the removal of pesticides: bentazon, carbofuran and 2,4-Dichlorophenoxyacetic acid (2,4-D) were investigated. Based on the central composite design (CCD), two factor interaction (2FI) and quadratic models were respectively employed to correlate the effect of variable parameters on the preparation of activated carbon used for the removal of pesticides with carbon yield. From the analysis of variance (ANOVA), the most influential factor on each experimental design response was identified. The optimum conditions for preparing the activated carbon from oil palm fronds were found as follows: activation temperature of 750 °C, activation time of 2 h and chemical impregnation ratio of 2.38. The percentage error between predicted and experimental results for the removal of bentazon, carbofuran and 2,4-D were 8.2, 1.3 and 9.2%, respectively and for the yield of the palm oil frond activated carbon was 5.6.     

Green synthesis of loofah-based biosorbent via radiation grafting for effective removal of methylene blue

A new loofah-based biosorbent with high adsorption capacity for cationic dye was synthesized by a one-step co-radiation grafting method. The successful grafting of sodium 4-vinylbenzene sulfonate (SSS) onto loofah sponge (LFs) through electron beam radiation can significantly improve the remove capacity of methylene blue in wastewater. The biosorbent with a 409.67 mg/g of uptake capacity for methylene blue (MB), was higher than most of the loofah based adsorbents reported. FT-IR, elemental analysis, XRD, SEM and TG were used to analyze the changes in the functional group composition, element content, morphology, thermal stability of the obtained biosorbent. The pH, contact time, temperature and the effect of dosage on adsorption were also investigated. The results showed that the adsorption behavior well accorded with the pseudo-second-order kinetic and Langmuir adsorption model, which proved that the adsorption was a single-layered and chemisorption process. The thermodynamic parameters suggested a spontaneous and endothermic process. XPS analysis confirmed a potential adsorption mechanism was based on hydrogen bond interaction, electrostatic interaction and π-π stacking. Additionally, the adsorbent owned outstanding reusability, which could be reused five times with a slight reduction of removal rate. Overall, this research enriches the MB trapping agent and provides a new methods for the reuse of waste natural loofah sponge, and it will be a valuable research with the advantages of low cost and less environmental pollution.     

Synthesis and application of treated activated carbon for cationic dye removal from modelled aqueous solution

Use of activated carbon (AC) prepared from rice husk and treated with anionic surfactant is investigated to eliminate cationic dye crystal violet (CV) using modelled dye solution. AC modified with anionic surfactant sodium lauryl sulfate (ACSLS) and other two surfactant namely sodium dodecyl sulfonate and hexadecyl trimethyl ammonium bromide were used for the analysis. Optimum ACSLS was analyzed and characterized using BET, XRD, SEM accompanied with XEDS, FTIR, HR-TEM and zeta potential, which confirms the sorption of CV onto ACSLS. Influence of pH, dose of adsorbent, concentration of initial dye, contact time, additive salts as well as actual water samples were investigated. Presence of NH⁴⁺, Ca²⁺, Mg²⁺, Na²⁺, Ca²⁺ and K⁺ cations in dye solution were having negligible (less than 4 %) influence on dye removal capacity. Study of mass transfer parameters revealed intra particle diffusion and film diffusion both played their part, whereas other kinetic studies has shown that experimental data fitted best with Pseudo 2nd order rate. Isotherm studies accompanied with error analysis revealed that Langmuir isotherm controls the adsorption equilibrium with highest capacity of CV adsorption with optimum operating conditions as pH = 6, temperature = 318 K, adsorbent dose = 100 mg/L and dye concentration = 30–60 mg/L. Study of thermodynamics and temperature analysis have shown that the sorption reaction was favourable and spontaneous with rise in temperature and endothermic in nature. Column studies are reported for varying rate of flow, depth of bed and dye concentrations along with analysis of column experimental data with various models like Yoon-Nelson, Thomas, Bohart-Adam and Clark model. Reusability (no. of cycles) of used adsorbent was studied using regeneration experiments. Analysis inferred that AC modified using surfactants can be a useful technique for enhanced adsorption capacity of dyes from aqueous solution and not much work has been reported on use of anionic surfactant modified AC for dye removal process.     

Green synthesis of activated carbon doped tungsten trioxide photocatalysts using leaf of basil (Ocimum basilicum) for photocatalytic degradation of methylene blue under sunlight

Tungsten oxide (WO₃) nanoparticles were prepared hydrothermally by basil leaves extract, and Activated Carbon (AC) was prepared by the carbonization of date pits. Moreover, 1, 2 and 3% of AC doped WO₃ nanoparticles have been fabricated under hydrothermal conditions. The obtained samples have been characterized by using different techniques such as x-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), simultaneous thermogravimetric analysis (TG-DTGA), fourier transform infrared (FT-IR), BET surface area, and Ultra-Violet spectroscopy (UV–Vis). It was observed that band-gap energy of the fabricated materials decreases by increasing AC amount. Similarly, BET surface area and porosity results showed increasing the content of AC, surface area, pore size and pore volume were decreased. The functional groups, determined by FT-IR, played a significant role in the photocatalytic performance. The photocatalytic performance of fabricated samples was used for the degradation of methylene blue (MB) at neutral pH under visible light radiations, and it is observed that WO₃/3%AC photocatalyst showed the highest degradation of MB. Both, capped phytochemicals of basil extract and the nanocomposites, were improved the photocatalytic performance, about 94% photodegradation was observed within 25 min under the reaction conditions. The photocatalyst was stable and about 85% and 81% photodegradation of MB were found under the two times of reusability tests.     

Conversion of Waste Tyres into Carbon Black and their Utilization as Adsorbent

Pyrolysis has the potential of transforming used tyres into useful recyclable products. Pyrolytic carbon black is one of the most important products of tyre pyrolysis. Waste tyres were pyrolysed at 450 °C in a batch reactor under atmospheric pressure. The recovered pyrolytic carbon black residues were studied to investigate their characteristics for use as a possible adsorbent. EDX elemental analysis and surface area determinations were used to investigate the distinctive features of pyrolytic carbon black. Due to various inorganic additives of the original tyre that contaminated the carbon black obtained, it was treated with acid for demineralization. The demineralized carbon black was activated at 900 °C in a furnace. It was observed that acid treatment and activation increased the surface areas and decreased the concentration of contaminants. Furthermore, adsorption characteristics of methylene blue on acid‐treated and activated carbon black (prepared via acid treatment) were compared with those of commercial activated carbon in liquid phase adsorption. It was found that adsorption capacity of methylene blue on acid‐treated activated carbon black was greater.