热释电探测器积分响应测试系统研究

为了实现对红外探测器积分响应的自动测量,配合虚拟仪器技术搭建了一套热释电红外探测器积分响应自动测试系统。利用双绞线将测试仪器与计算机连接,以LabVIEW为开发平台编写软件测试系统,遥控测量仪器,实现计算机自动采集和处理数据实时绘制曲线,对LT-020-H型热释电红外探测器在不同调制频率下的积分响应度进行了测试并分析。在500K的黑体辐射下,探测器积分响应度达到3.5×106V/W。通过对实验结果进行分析,得到了探测器响应、黑体辐射温度以及信号调制频率之间的关系。     

多通道热释电IRFPA图像拼接采集系统

为了实现分辨率高的大规模热释电IRFPA探测器,设计了多路通道并行输出的读出电路。针对多路输出的热释电IRFPA探测器,依据热释电探测的时序要求,设计了图像拼接采集系统。利用外部驱动信号控制采集卡的触发及采样时钟,由斩波器同步信号判断热释电探测器的亮场及暗场信号。构造PC-DAQ虚拟仪器系统对多通道输出的热释电型IRFPA进行多路并行图像采集,并对每路图像信号进行亮、暗场判断后进行差分处理,通过软件拼接处理成一副完整的图像,最终在软件平台上显示。对实验室研制的160列120行双通道读出及320列120行四通道读出的热释电读出电路进行了图像采集实验,对于同样阵列大小的单通道读出探测器,双通道结构读出速度提高了1倍,四通道结构读出速度提高了3倍。通过采集成像实验验证了系统的可行性。     

远场天线自动测试系统的研究与实现

针对天线参数测试过程及测试要求,分析在天线参数测试中的主要问题,研究实际测试过程中环境因素对天线参数测量结果的影响,提出了一种基于虚拟仪器技术的远场天线性能参数自动测试系统的设计方案,详细阐述了该方案的系统组成部分与工作原理,包括矢量网络分析仪、天线测试转台与吊杆的控制原理以及数据采集的时序设计,结合Matlab实现了对影响因素的误差补偿与天线性能参数的测试计算方法,利用数据库技术实现天线测试数据的存储、读取与报告打印,通过现场测试试验验证了该方案的可靠性与可行性。     

集成化光束质量测试系统

集成化光束质量测试系统的探头包括卡塞格仑扩束器、准直镜、分光元件、自准直光源扩束器、671μm激光器、分束元件，集成化光束质量测试系统的结构见图1。采集处理系统包含CCD探测器和采集卡、处理软件。由于采集系统的探测器为模拟相机，由探测器输出的复合视频信号经采集卡进行A／D转换，送入计算机，由采集软件对光班图像进行处理，获取远场光班的数据。再利用输入光束的参数和光学系统的参数即可得到被测光束的光束质量。     

基于PCI总线的红外探测器图像数据采集系统设计与实现

红外成像探测系统在调测过程中,通常需要完成探测系统输出图像和辅助信息的采集、保存和分析;根据红外成像探测系统输出信息的特点,文章介绍了基于PCI总线技术的红外探测器图像数据采集系统的软硬件设计方法和实现方案,解决了多种分辨率红外图像的实时数据采集、显示和储存问题;系统通过接受320*256以及640*512分辨率的图像进行测试;经过测试表明:通过使用DMA方式,PCI总线读取速率达到了49.0 MByte/s,可以准确无误地对多种分辨率红外图像和辅助信息进行高速实时采集,满足测试系统的使用需求,为红外成像探测系统的调测提供了坚实的基础。     

嵌入式软件GUI自动化测试平台研究

为实现嵌入式软件的GUI自动化测试,本文对嵌入式软件GUI自动化测试现状深入分析,提出了一种无侵入式的GUI自动化测试框架,利用图像采集与信息识别技术实现测试用例结果判断;利用键盘鼠标模拟技术模拟测试用例执行的人机交互;利用脚本语言嵌入技术实现用例编辑与转换、利用嵌入式软件GUI测试自动化控制技术实现用例的自动驱动与执行。在此基础上,设计并研发了嵌入式软件GUI自动化测试平台,能够方便、有效的实现无侵入式的嵌入式GUI自动化测试。     

虚拟仪器实现光谱测试的数据采集和处理

为了增强光谱测试系统的数据采集和分析处理能力,对新兴的基于微型计算机的测试仪器技术———虚拟仪器作了研究,并将其引入光谱测试中。以编译型的可视化图形编程环境ＬａｂＶＩＥＷ（实验室虚拟仪器工程平台）作为开发平台,开发出用于光谱测试和光谱数据处理的虚拟仪器系统。对光源和光探测器的光谱特性进行测试的实例表明,在ＬａｂＶＩＥＷ上构建的虚拟仪器提高了光谱测试的自动化程度、精确度和测试效率。虚拟仪器在光电检测中的应用具有广阔的发展前景     

紫外单光子成像系统的研究

搭建了紫外单光子成像系统,详细介绍了该系统的组成、工作原理和分辨率性能测试.由汞灯发出的紫外光经过大气散射、多块减光片得到了紫外单光子流.单光子直接打在微通道板上,微通道板产生的倍增电子由楔条形阳极收集,电荷灵敏前置放大器将阳极输出的电荷信号转变为电压信号,主放大器对前放信号进行滤波整形.利用高速数据采集卡连续采集主放大器的输出波形,通过软件对采集波形进行处理,采用图像处理技术得到了紫外单光子10min的计数图像,并对图像进行了畸变校正.此外,通过自己设计的分辨率板,测得该系统的分辨率可达150μm.该系统在极微弱光探测成像,生物发光,空间环境探测等方面具有广泛应用. 关键词： 单光子计数成像 阳极探测器 楔条形阳极 分辨率     

基于NI FlexRIO的图像实时采集及处理系统

为了解决视觉测量中图像的实时采集及处理问题,以NI FlexRIO为基础,采用虚拟仪器技术,利用LabVIEW图形化开发平台,并结合相关技术知识,如乒乓操作、流水线技术等,研制了一套图像实时采集及处理系统。该系统并行地实时地实现了图像的采集、存储及处理,在图像分辨率为1 2801 024、采集速率为500 f/s的情况下,系统工作稳定,图像处理速度小于2 ms,并且处理精度达到了亚像素级。该系统对于实现视觉测量的实时性具有重要意义,并且其良好的性能使其在其他相关领域也具有很高的实用价值。     

CSNS多功能反射谱仪主探测器读出电子学系统研制

为满足中国散裂中子源（CSNS）多功能反射谱仪（MR）主探测器高气压3He多丝正比室探测器（MWPC）的需求,研制了专用的读出电子学系统。该系统主要由核心前放板和触发扇出板构成,其中以前放板为核心,采用了6块前放板实现探测器142路模拟信号的数字化,并通过判选机制甄别中子信息,将有效中子事例打包发送给后端,触发扇出板提供同一时刻到达的T0信号和触发信号,以确保数据的对齐。读出电子学系统分别在实验室和束流条件下,进行了相关指标测试,测试结果表明性能优于设计要求。目前MWPC探测器已经成功安装到MR谱仪现场,并且已经开始稳定运行。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.