Comparison between direct and indirect immunofluorescence method for determination of somatic cell count

A sensitive indirect immunofluorescence (IF) assay for bovine neutrophil and somatic cell counting was developed. The obtained indirect IF was compared with direct IF. The direct IF method uses a single-fluorophore-conjugated antibody directed against the target of interest. The indirect IF method uses two antibodies. The primary antibody is unconjugated. The secondary antibody is directed against the primary and has fluorescent marker. Calibration curves for somatic cells (SC) in buffer model solutions were obtained by both methods, using fluorescence spectrophotometry. The measured linear range of somatic cells by the direct method was from 2?×?10⁴ to 3?×?10⁶ cells and by the indirect method was from 3?×?10⁴ to 3?×?10⁶ cells. The signal obtained by the indirect method was higher than the direct method at low concentrations of SC (from 30,000 to 100 000 cells/mL). That signal amplification probably is due to more than one fluorescent secondary antibody coupling to bound primary antibody. The same effect is observed by fluorescence microscopy. Consequently, the indirect IF method is more sensitive than the direct IF method. Conjugated primary antibodies are more expensive than their unconjugated counterparts, and secondary antibodies are relatively inexpensive. Therefore, using the same conjugated secondary antibody to detect different primary antibodies is cost-effective. Furthermore, a two-color staining microscopic procedure was proposed for simultaneous estimation of total SC count and neutrophil cell count.     

Bioconjugated and cross-linked bionanostructures for bifunctional immunohistochemical labeling

The present study describes the development and use of a new bioconjugate combining targeted quantum dot labeling with an immunoperoxidase method and explores whether these bioconjugates could specifically and effectively label Cu/Zn superoxide dismutase (SOD1). The new bioconjugate is designed for the examination of samples both under fluorescent and bright-field microscopy at the same time. For this purpose chlorobis(2-2'-bipyridyl) methacryloyl tyrosine-ruthenium(II) and bis (2-2'-bipyridyl) methacryloyltyrosine-methacryloyltryptophan-ruthenium (II) photosensitive monomers and photosensitive poly(Bis (2-2'-bipyridyl)) methacryloyltyrosine-methacryloyltryptophan-ruthenium(II) were synthesized and characterized. The anti-SOD1 antibody and horseradish peroxidase (HRD) conjugated quantum dots were prepared by using this polymer. The anti-SOD1 antibody and HRD conjugated quantum dots were used in labeling and imaging of SOD1 in rat liver sections. Quantum dot particles were observed as a bright fluorescence in their specific binding locations inside the hepatocytes. The HRD-diaminobenzidine reaction product was observed as brown-colored particles at the same locations under bright-field microscopy. Structural details of the tissue sections could be examined at the same time. The conjugation protocol is simple; the bioconjugate is applicable for efficient cell labeling and can be adapted for imaging of other targets in different tissues. Also, the prepared nanobioconjugates have mechanic stability and can be used for a long period.     

双靶向CdTe量子点的制备及其在细胞标记中的应用

以巯基乙酸和巯基乙酰肼为稳定剂,制备了酸度敏感型CdTe量子点。经与抗体链接,该量子点具备酸度敏感、免疫识别双重靶向功能。经荧光光谱分析、透射电镜图像及细胞免疫成像证明,抗体已成功链接于量子点表面,且该量子点具有酸度敏感及抗体识别的双重靶向功能,可以实现对肿瘤细胞的特异性标记。     

信号肽功能化二氧化硅纳米颗粒的线粒体靶向作用研究

以N-(p-Maleimidophenyl)isocyanate(PMPI)为交联剂, 将线粒体信号肽分子共价修饰到二氧化硅荧光纳米颗粒表面, 构建线粒体信号肽功能化二氧化硅荧光纳米颗粒. 采用荧光分光光度计、Zeta电位仪以及透射电子显微镜对修饰前后的二氧化硅纳米颗粒进行了表征. 结果表明, 信号肽可被成功修饰在纳米颗粒表面, 并且纳米颗粒粒径在信号肽分子修饰前后没有发生明显变化. 以分离纯化的细胞核作为对照, 采用流式细胞术考察了信号肽功能化二氧化硅荧光纳米颗粒与分离纯化后的线粒体的相互作用. 结果表明, 线粒体信号肽修饰到二氧化硅纳米颗粒表面后依然保持良好的生物活性, 能够介导二氧化硅纳米颗粒特异性识别及结合分离纯化的线粒体, 从而为线粒体监测及其功能调控研究提供了新的思路.     

BirA*-protein A fusion protein based BioEnhancer amplifies western blot immunosignal

Western blot (protein immunoblot) is a widely used analytical technique in molecular biology. Utilizing the specific recognizing primary antibody, proteins immobilized on various matrix are investigated by subsequent visualization steps, for example, by the horse radish peroxidase conjugated secondary antibody incubation. Methods to improve the sensitivity in protein identification or quantification are appreciated by biochemists. Herein, we report a new strategy to amplify Western blot signals by constructing a probe with proximal labeling and IgG targeting abilities. The R118G mutation attenuated the biotin-AMP binding affinity of the bacterial biotin ligase BirA*, offering a proximity-dependent labeling ability, which could be used as a signal amplifier. We built a BirA*-protein A fusion protein (BioEnhancer) that specifically binds to IgG and adds biotin tags to its proximal amine groups, enhancing the immunosignal of target proteins. In our experiments, the BioEnhancer system amplified the immunosignal by tenfold compared to the standard western blot. Additionally, our strategy could couple with other signal enhancement methods to further increase the western blot sensitivity.     

Synthesis and characterization of photoswitchable fluorescent SiO2 nanoparticles

Switchable fluorescent silica nanoparticles have been prepared by covalently incorporating a fluorophore and a photochromic compound inside the particle core. The fluorescence can be switched reversibly between an on‐ and off‐state via energy transfer. The particles were synthesized using different amounts of the photoswitchable compound (spiropyran) and the fluorophore (rhodamine B) in a size distribution between 98 and 140 nm and were characterized in terms of size, switching properties, and fluorescence efficiency by TEM, and UV\Vis and fluorescence spectroscopy.     

A ratiometric fluorescent viscosity sensor

The development of a dual probe that provides ratiometric measurements of fluid viscosity is described. The design is based on coupling of a primary fluorophore with viscosity-independent fluorescence emission (blue unit) with a secondary fluorophore that exhibits viscosity-sensitive fluorescent emission quantum yield (red unit). Excitation of the secondary fluorophore can be achieved via Resonance Energy Transfer. The ratio of the fluorescence emission of these fluorophores provides an accurate, ratiometric measurement of solvent viscosity.     

Fluorescent Vesicular Particles Assembled by Inclusion Complexes Between Cyclodextrins and BPB

Vesicular particles based on inclusion complexes between BPB and γ-HB-β-CDs were prepared and characterized for the first time. The morphologies and sizes were confirmed by transmission electron microscopy (TEM), scanning electron microscope (SEM), and dynamic light scattering (DLS). Particularly, these vesicular particles exhibiting clearly fluorescent dots observed by laser confocal scanning microscopy (LCSM) could be alternative candidates as fluorescent probes and labels being applied to cellular staining, labeling, bio-mimicking and drug delivery. The ultraviolet, fluorescence, and nuclear magnetic resonance (NMR) measurements confirmed the existence of stable 1:1 BPB-γ-HB-β-CD complexes in the system. The vesicular particles were assumed to be constructed by orderly self-aggregates of these inclusion complexes.     

Synthesis and Characterization of Far‐Red/NIR‐Fluorescent BODIPY Dyes,Solid‐State Fluorescence,and Application as Fluorescent Tags Attached to Carbon Nano‐onions

A series of π‐extended distyryl‐substituted boron dipyrromethene (BODIPY) derivatives with intense far‐red/near‐infrared (NIR) fluorescence was synthesized and characterized, with a view to enhance the dye’s performance for fluorescence labeling. An enhanced brightness was achieved by the introduction of two methyl substituents in the meso positions on the phenyl group of the BODIPY molecule; these substituents resulted in increased structural rigidity. Solid‐state fluorescence was observed for one of the distyryl‐substituted BODIPY derivatives. The introduction of a terminal bromo substituent allows for the subsequent immobilization of the BODIPY fluorophore on the surface of carbon nano‐onions (CNOs), which leads to potential imaging agents for biological and biomedical applications. The far‐red/NIR‐fluorescent CNO nanoparticles were characterized by absorption, fluorescence, and Raman spectroscopies, as well as by thermogravimetric analysis, dynamic light scattering, high‐resolution transmission electron microscopy, and confocal microscopy.     

Minimal Tags for Rapid Dual‐Color Live‐Cell Labeling and Super‐Resolution Microscopy

The growing demands of advanced fluorescence and super‐resolution microscopy benefit from the development of small and highly photostable fluorescent probes. Techniques developed to expand the genetic code permit the residue‐specific encoding of unnatural amino acids (UAAs) armed with novel clickable chemical handles into proteins in living cells. Here we present the design of new UAAs bearing strained alkene side chains that have improved biocompatibility and stability for the attachment of tetrazine‐functionalized organic dyes by the inverse‐electron‐demand Diels–Alder cycloaddition (SPIEDAC). Furthermore, we fine‐tuned the SPIEDAC click reaction to obtain an orthogonal variant for rapid protein labeling which we termed selectivity enhanced (se) SPIEDAC. seSPIEDAC and SPIEDAC were combined for the rapid labeling of live mammalian cells with two different fluorescent probes. We demonstrate the strength of our method by visualizing insulin receptors (IRs) and virus‐like particles (VLPs) with dual‐color super‐resolution microscopy.     

Specific and stable fluorescence labeling of histidine-tagged proteins for dissecting multi-protein complex formation

Labeling of proteins with fluorescent dyes offers powerful means for monitoring protein interactions in vitro and in live cells. Only a few techniques for noncovalent fluorescence labeling with well-defined localization of the attached dye are currently available. Here, we present an efficient method for site-specific and stable noncovalent fluorescence labeling of histidine-tagged proteins. Different fluorophores were conjugated to a chemical recognition unit bearing three NTA moieties (tris-NTA). In contrast to the transient binding of conventional mono-NTA, the multivalent interaction of tris-NTA conjugated fluorophores with oligohistidine-tagged proteins resulted in complex lifetimes of more than an hour. The high selectivity of tris-NTA toward cumulated histidines enabled selective labeling of proteins in cell lysates and on the surface of live cells. Fluorescence labeling by tris-NTA conjugates was applied for the analysis of a ternary protein complex in solution and on surfaces. Formation of the complex and its stoichiometry was studied by analytical size exclusion chromatography and fluorescence quenching. The individual interactions were dissected on solid supports by using simultaneous mass-sensitive and multicolor fluorescence detection. Using these techniques, formation of a 1:1:1 stoichiometry by independent interactions of the receptor subunits with the ligand was shown. The incorporation of transition metal ions into the labeled proteins upon labeling with tris-NTA fluorophore conjugates provided an additional sensitive spectroscopic reporter for detecting and monitoring protein-protein interactions in real time. A broad application of these fluorescence conjugates for protein interaction analysis can be envisaged.     

Synthesis of aqueous CdTe quantum dots embedded silica nanoparticles and their applications as fluorescence probes

This paper presents the synthesis of aqueous CdTe QDs embedded silica nanoparticles by reverse microemulsion method and their applications as fluorescence probes in bioassay and cell imaging. With the aim of embedding more CdTe QDs in silica spheres, we use poly(dimethyldiallyl ammonium chloride) to balance the electrostatic repulsion between CdTe QDs and silica intermediates. By modifying the surface of CdTe/SiO₂ composite nanoparticles with amino and methylphosphonate groups, biologically functionalized and monodisperse CdTe/SiO₂ composite nanoparticles can be obtained. In this work, CdTe/SiO₂ composite nanoparticles are conjugated with biotin-labeled mouse IgG via covalent binding. The biotin-labeled mouse IgG on the CdTe/SiO₂ composite nanoparticles surface can recognize FITC-labeled avidin and avidin on the surface of polystyrene microspheres by protein-protein binding. Finally, the CdTe/SiO₂ composite nanoparticles with secondary antibody are used to label the MG63 osteosarcoma cell with primary antibody successfully, which demonstrates that the application of CdTe/SiO₂ composite nanoparticles as fluorescent probes in bioassay and fluorescence imaging is feasible.     

Anti-Her-2 monoclonal antibody conjugated polymer fluorescent nanoparticles probe for ovarian cancer imaging

Fluorescent nanoparticles (FNPs) with unique optical properties may be useful as biosensors in living cancer cell imaging and cancer targeting. A novel kind of polymer fluorescent nanoparticles (PFNPs) was synthesized and its application for ovarian cancer imaging with fluorescence microscopy imaging technology was presented in this study. The PFNPs were synthesized with precipitation polymerization by using methacrylic acid (MAA) as monomer, trimethylolpropane trimethacrylate (Trim) as cross-linker, azobisisobutyronitrile (AIBN) as radical initiator and butyl rhodamine B (BTRB) as fluorescent dye. And the fluorescent dye was embedded into the three-dimensional network of the polymer when the polymer was produced. With this method the PFNPs can be prepared easily. And then the PFNPs were successfully modified with anti-Her-2 monoclonal antibody. The fluorescence probe based on anti-Her-2 monoclonal antibody conjugated PFNPs has been used to detect ovarian cancer cells with fluorescence microscopy imaging technology. The experimental results demonstrate that the anti-Her-2 monoclonal antibody conjugated PFNPs can effectively recognize ovarian cancer cells and exhibit good sensitivity and exceptional photostability, which would provide a novel way for the diagnosis and curative effect observation of ovarian cancer cells.     

Conjugated polyelectrolyte-grafted silica microspheres

A direct method for preparation of conjugated polymer-grafted silica particles is reported. Silica particles (0.3 and 5 mum diameter) are treated with a 3-(trimethoxysilyl)propylamine derivative that is functionalized with an aryl iodide unit. A solution step-growth polymerization reaction is performed in solution that contains a dispersion of the aryl iodide-functionalized particles. The reaction is a Pd(0)-catalyzed (Sonogashira) A-B-type polymerization of an oligo(ethylene glycol)-fuctionalized diiodobenzene and a bis(propyloxy)sulfonate-substituted diethynylbenzene. The overall process affords silica particles that feature a surface graft layer of an anionic poly(phenylene ethynylene)-type conjugated polyelectrolyte. The particle surface modification process was monitored by infrared (FTIR) spectroscopy, and the polymer-grafted silica particles were characterized by thermogravimetric analysis, scanning and transmission electron microscopy, confocal fluorescence microscopy, and absorption and fluorescence spectroscopy. The conjugated polyelectrolyte-grafted silica particles are highly fluorescent, and a Stern-Volmer quenching study of the particles' fluorescence with electron-transfer- and energy-transfer-type quenchers shows that the quenching response depends on the type of quenching mechanism.     

Phosphorylated 3‐Heteroarylcoumarins and Their Use in Fluorescence Microscopy and Nanoscopy

Photostable and bright fluorescent dyes with large Stokes shifts are widely used as markers in far‐field optical microscopy, but the variety of useful dyes is limited. The present study introduces new 3‐heteroaryl coumarins decorated with a primary phosphate group (OP(O)(OH)₂) attached to C‐4 in 2,2,4‐trimethyl‐1,2‐dihydroquinoline fragment fused with the coumarin fluorophore. The general synthetic route is based on the Suzuki reaction of 3‐bromocoumarines with hetarylboronic acids followed by oxidation of the methyl group at the C?C bond with SeO₂ (to an aldehyde), reduction with NaBH₄ (to an alcohol), and conversion into a primary phosphate. The 4 position in the coumarin system may be unsubstituted or bear a methyl group. Phosphorylated coumarins were found to have high fluorescence quantum yields in the free state and after conjugation with proteins (in aqueous buffers). In super‐resolution light microscopy with stimulated emission depletion (STED), the new coumarin dyes provide an optical resolution of 40–60 nm with a low background signal. Due to their large Stokes shifts and high photostability, phosphorylated coumarins enable to combine multilabel imaging (using one detector and several excitation sources) with diffraction unlimited optical resolution.     

Synthesis and evaluation of self-calibrating ratiometric viscosity sensors

We describe the design, synthesis and fluorescent profile of a family of self-calibrating dyes that provide ratiometric measurements of fluid viscosity. The design is based on covalently linking a primary fluorophore (reference) that displays a viscosity-independent fluorescence emission with a secondary fluorophore (sensor) that exhibits a viscosity-sensitive fluorescence emission. Characterization of fluorescent properties was made with separate excitation of the units and through Resonance Energy Transfer from the reference to the sensor dye. The chemical structures of both fluorophores and the linker length have been evaluated in order to optimize the overall brightness and sensitivity of the viscosity measurements. We also present an application of such ratiometric dyes for the detection of membrane viscosity changes in a liposome model.     

Anti-epidermal growth factor receptor (anti-EGFR) antibody conjugated fluorescent nanoparticles probe for breast cancer imaging

Fluorescent nanoparticles (FNs) with unique optical properties may be useful as biosensors in living cancer cell imaging and cancer targeting. In this study, anti-EGFR antibody conjugated fluorescent nanoparticles (FNs) (anti-EGFR antibody conjugated FNs) probe was used to detect breast cancer cells. FNs with excellent character such as non-toxicity and photostability were first synthesized with a simple, cost-effective and environmentally friendly modified Stőber synthesis method, and then successfully modified with anti-EGFR antibody. This kind of fluorescence probe based on the anti-EGFR antibody conjugated FNs has been used to detect breast cancer cells with fluorescence microscopy imaging technology. The experimental results demonstrate that the anti-EGFR antibody conjugated FNs can effectively recognize breast cancer cells and exhibited good sensitivity and exceptional photostability, which would provide a novel way for the diagnosis and curative effect observation of breast cancer cells and offer a new method in detecting EGFR.     

Fluorescent polymer particles incorporating pyrene derivatives

Fluorescent polymer particles incorporating pyrene and alkynylpyrenes were prepared by miniemulsion polymerization of styrene. The pyrenes were simply dissolved in styrene monomer and then added to the reaction mixture in a vessel, followed by ultrasonication and the polymerization. The pyrenes were incorporated in the polystyrene particles and gave monomer fluorescence emission. The fluorescent particles incorporating the alkynylpyrenes, which have high fluorescence quantum yield and short fluorescence lifetime, showed the same fluorescence emission intensity under air and nitrogen. The fluorescence of the alkynylpyrenes in the polymer particles will not be quenched by molecular dioxygen in contrast to that in organic solvents. Incorporation of fluorophore into polymer particles will protect the fluorophore from its undesirable interaction with oxygen, affording the particles highly fluorescent even under air. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1470–1475, 2008     

Make them Blink: Probes for Super‐Resolution Microscopy

In recent years, a number of approaches have emerged that enable far‐field fluorescence imaging beyond the diffraction limit of light, namely super‐resolution microscopy. These techniques are beginning to profoundly alter our abilities to look at biological structures and dynamics and are bound to spread into conventional biological laboratories. Nowadays these approaches can be divided into two categories, one based on targeted switching and readout, and the other based on stochastic switching and readout of the fluorescence information. The main prerequisite for a successful implementation of both categories is the ability to prepare the fluorescent emitters in two distinct states, a bright and a dark state. Herein, we provide an overview of recent developments in super‐resolution microscopy techniques and outline the special requirements for the fluorescent probes used. In combination with the advances in understanding the photophysics and photochemistry of single fluorophores, we demonstrate how essentially any single‐molecule compatible fluorophore can be used for super‐resolution microscopy. We present examples for super‐resolution microscopy with standard organic fluorophores, discuss factors that influence resolution and present approaches for calibration samples for super‐resolution microscopes including AFM‐based single‐molecule assembly and DNA origami.     

Hydrogen‐Bond and Supramolecular‐Contact Mediated Fluorescence Enhancement of Electrochromic Azomethines

An electronic push–pull fluorophore consisting of an intrinsically fluorescent central fluorene capped with two diaminophenyl groups was prepared. An aminothiophene was conjugated to the two flanking diphenylamines through a fluorescent quenching azomethine bond. X‐ray crystallographic analysis confirmed that the fluorophore formed multiple intermolecular supramolecular bonds. It formed two hydrogen bonds involving a terminal amine, resulting in an antiparallel supramolecular dimer. Hydrogen bonding was also confirmed by FTIR and NMR spectroscopic analyses, and further validated theoretically by DFT calculations. Intrinsic fluorescence quenching modes could be reduced by intermolecular supramolecular contacts. These contacts could be engaged at high concentrations and in thin films, resulting in fluorescence enhancement. The fluorescence of the fluorophore could also be restored to an intensity similar to its azomethine‐free counterpart with the addition of water in >50 % v/v in tetrahydrofuran (THF), dimethyl sulfoxide (DMSO), and acetonitrile. The fluorophore also exhibited reversible oxidation and its color could be switched between yellow and blue when oxidized. Reversible electrochemically mediated fluorescence turn‐off on turn‐on was also possible.