Electrospun Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript>/Li<Subscript>2</Subscript>TiO<Subscript>3</Subscript> composite nanofibers for enhanced high-rate lithium ion batteries

Li₄Ti₅O₁₂/Li₂TiO₃ composite nanofibers with the mean diameter of ca. 60 nm have been synthesized via facile electrospinning. When the molar ratio of Li to Ti is 4.8:5, the Li₄Ti₅O₁₂/Li₂TiO₃ composite nanofibers exhibit initial discharge capacity of 216.07 mAh g^?1 at 0.1 C, rate capability of 151 mAh g^?1 after being cycled at 20 C, and cycling stability of 122.93 mAh g^?1 after 1000 cycles at 20 C. Compared with pure Li₄Ti₅O₁₂ nanofibers and Li₂TiO₃ nanofibers, Li₄Ti₅O₁₂/Li₂TiO₃ composite nanofibers show better performance when used as anode materials for lithium ion batteries. The enhanced electrochemical performances are explained by the incorporation of appropriate Li₂TiO₃ which could strengthen the structure stability of the hosted materials and has fast Li⁺-conductor characteristics, and the nanostructure of nanofibers which could offer high specific area between the active materials and electrolyte and shorten diffusion paths for ionic transport and electronic conduction. Our new findings provide an effective synthetic way to produce high-performance Li₄Ti₅O₁₂ anodes for lithium rechargeable batteries.     

Mesoporous Spherical Li4Ti5O12 as High‐Performance Anodes for Lithium‐Ion Batteries

Porous microspherical Li₄Ti₅O₁₂ aggregates (LTO‐PSA) can be successfully prepared by using porous spherical TiO₂ as a titanium source and lithium acetate as a lithium source followed by calcinations. The synthesized LTO‐PSA possess outstanding morphology, with nanosized, porous, and spherical distributions, that allow good electrochemical performances, including high reversible capacity, good cycling stability, and impressive rate capacity, to be achieved. The specific capacity of the LTO‐PSA at 30 C is as high as 141 mA h g^?1, whereas that of normal Li₄Ti₅O₁₂ powders prepared by a sol–gel method can only achieve 100 mA h g^?1. This improved rate performance can be ascribed to small Li₄Ti₅O₁₂ nanocrystallites, a three‐dimensional mesoporous structure, and enhanced ionic conductivity.     

Molecular Design Strategy for Ordered Mesoporous Stoichiometric Metal Oxide

A molecular design strategy is used to construct ordered mesoporous Ti³⁺‐doped Li₄Ti₅O₁₂ nanocrystal frameworks (OM‐Ti³⁺‐Li₄Ti₅O₁₂) by the stoichiometric cationic coordination assembly process. Ti⁴⁺/Li⁺‐citrate chelate is designed as a new molecular precursor, in which the citrate can not only stoichiometrically coordinate Ti⁴⁺ with Li⁺ homogeneously at the atomic scale, but also interact strongly with the PEO segments in the Pluronic F127. These features make the co‐assembly and crystallization process more controllable, thus benefiting for the formation of the ordered mesostructures. The resultant OM‐Ti³⁺‐Li₄Ti₅O₁₂ shows excellent rate (143 mAh g^?1 at 30 C) and cycling performances (<0.005 % fading per cycle). This work could open a facile avenue to constructing stoichiometric ordered mesoporous oxides or minerals with highly crystalline frameworks.     

Synthesis of Li4Ti5O12 fibers as a high-rate electrode material for lithium-ion batteries

Porous lithium titanate (Li₄Ti₅O₁₂) fibers, composed of interconnected nanoparticles, are synthesized by thermally treating electrospun precursor fibers and utilized as an energy storage material for rechargeable lithium-ion batteries. The material is characterized by X-ray diffraction, scanning electron microscopy, high-resolution transmission electron microscopy, and thermal analysis. Scanning electron microscopy results show that the Li₄Ti₅O₁₂ fibers calcined at 700?°C have an average diameter of 230?nm. Especially, the individual fiber is composed of nanoparticles with an average diameter of 47.5?nm. Electrochemical properties of the material are evaluated using cyclic voltammetry, galvanostatic cycling, and electrochemical impedance spectroscopy. The results show that as-prepared Li₄Ti₅O₁₂ exhibits good cycling capacity and rate capability. At the charge–discharge rate of 0.2, 0.5, 1, 2, 10, 20, 40, and 60?C, its discharge capacities are 172.4, 168.2, 163.3, 155.9, 138.7, 123.4, 108.8, and 90.4?mAh?g^?1, respectively. After 300 cycles at 20?C, it remained at 120.1?mAh?g^?1. The obtained results thus strongly support that the electrospun Li₄Ti₅O₁₂ fibers could be one of the most promising candidate anode materials for lithium-ion batteries in electric vehicles.     

Preparation of Li4Ti5O12 Yolk–Shell Powders by Spray Pyrolysis and their Electrochemical Properties

We have reported for the first time the preparation of yolk–shell‐structured Li₄Ti₅O₁₂ powders for use as anode materials in lithium‐ion batteries. One Li₄Ti₅O₁₂ yolk–shell‐particle powder is directly formed from each droplet containing lithium, titanium, and carbon components inside the hot wall reactor maintained at 900 °C. The precursor Li₄Ti₅O₁₂ yolk–shell‐particle powders, which are directly prepared by spray pyrolysis, have initial discharge and charge capacities of 155 and 122 mA h g^?1, respectively, at a current density of 175 mA g^?1. Post‐treatment of the yolk–shell‐particle powders at temperatures of 700 and 800 °C improves the initial discharge and charge capacities. The initial discharge capacities of the Li₄Ti₅O₁₂ powders with a yolk–shell structure and a dense structure post‐treated at 800 °C are 189 and 168 mA h g^?1, respectively. After 100 cycles, the corresponding capacities are 172 and 152 mA h g^?1, respectively (retentions of 91 and 90 %).     

Sol–gel preparation and electrochemical properties of La-doped Li4Ti5O12 anode material for lithium-ion battery

A sol–gel method using Ti(OC₄H₉)₄, LiCH₃COO·2H₂O, and La(NO₃)₃·6H₂O as starting materials and ethyl acetoacetate as chelating agent to prepare pure and lanthanum (La)-doped Li₄Ti₅O₁₂ is reported. The structure and morphology of the active materials characterized by powder X-ray diffraction and scanning electron microscopy analysis indicate that doping with a certain amount of La³⁺ does not affect the structure of Li₄Ti₅O₁₂, but can restrain the agglomeration of the particles during heat treatment. The electrochemical properties measured by cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge–discharge cycling tests show that La-doped Li₄Ti₅O₁₂ presents a much improved electrochemical performance due to a decrease in charge transfer resistance. At current densities of 1 and 5 C, the La-doped Li₄Ti₅O₁₂ exhibits excellent reversible capacities of 156.16 and 150.79 mAh?g^?1, respectively. The excellent rate capability and good cycling performance make La-doped Li₄Ti₅O₁₂ a promising anode material for lithium-ion batteries in energy storage systems.     

Synthesis of γ-LiV2O5 nanorods as a high-performance cathode for Li ion battery

One-dimension γ-LiV₂O₅ nanorods were synthesized using VO₂(B) nanorods as precursor in this study. The as-prepared material is characterized by X-ray diffraction, X-ray photoelectron spectrometry, Fourier-transform infrared, transmission electron microscopy (TEM), cyclic voltammetry, and charge–discharge cycling test. TEM results show that LiV₂O₅ nanorods are 90–250 nm in diameter. The nanorods deliver a maximum discharge capacity of 284.3 mAh g^?1 at 15 mA g^?1 and 270.2 mAh g^?1 is maintained at the 15th cycle. Good rate performance is also observed with the discharge capacity of 250.1 and 202.6 mAh g^?1 at 50 and 300 mA g^?1, respectively. The capacity retention at 300 mA g^?1 is 84.2% over 50 cycles. The Li⁺ diffusion coefficient of LiV₂O₅ is calculated to be 10^-10–10^?9 cm² s^?1. It is demonstrated that the nanorod morphology could greatly facilitate to shorten lithium ion diffusion pathways and increase the contact area between active material and electrolyte, resulting in high capacity and rate performance for LiV₂O₅.     

Low‐temperature Synthesis of Peony‐like Spinel Li4Ti5O12 as a High‐performance Anode Material for Lithium Ion Batteries

Peony‐like spinel Li₄Ti₅O₁₂ was synthesized via calcination of precursor at the temperature of 400°C, and the precursor was prepared through a hydrothermal process in which the reaction of hydrous titanium oxide with lithium hydroxide was conducted at 180°C. The as‐prepared product was investigated by SEM, TEM and XRD, respectively. As anode material for lithium ion battery, the Li₄Ti₅O₁₂ obtained was also characterized by galvanostatic tests and cyclic voltammetry measurements. It is found that the peony‐like Li₄Ti₅O₁₂ exhibited high rate capability of 119.7 mAh·g⁻¹ at 10 C and good capacity retention of 113.8 mAh·g⁻¹ after 100 cycles at 5 C, and these results indicate the peony‐like Li₄Ti₅O₁₂ has promising applications for lithium ion batteries with high performance.     

Morphology-controllable synthesis of LiMn2O4 particles as cathode materials of lithium batteries

We reported a new method for the preparation of morphology-controllable LiMn₂O₄ particles. In this method, dimension-different MnO₂ nanowires synthesized hydrothermally by adjusting the reaction temperature were used as the precursor. The morphology and structure of the resulting products were characterized with scanning electron microscope and X-ray diffraction, and the performances of the prepared LiMn₂O₄ samples as cathode material of lithium batteries were investigated by cyclic voltammetry and galvanostatic charge/discharge test. The results indicate that the morphology of LiMn₂O₄ transforms from tridimensional particle (TP) to unidimensional rod (UR) through quadrate lamina (QL) with increasing the diameter and length of MnO₂ nanowires. Although the cyclic stabilities of LiMn₂O₄-TP, LiMn₂O₄-QL, and LiMn₂O₄-UR are very close (the 0.1 C capacity after 50 cycles is 101, 93, and 99 mAh g^?1 at 25 °C, and 84, 78, and 82 mAh g^?1 at 50 °C, respectively), LiMn₂O₄-QL delivers much higher rate capacity (about 70 mAh g^?1 at 5 C and 30 mAh g^?1 at 10 C) than LiMn₂O₄-TP and LiMn₂O₄-UR (about 20 mAh g^?1 at 5 C, 3 mAh g^?1 at 10 C, 25 mAh g^?1 at 5 C, and 3 mAh g^?1 at 10 C).     

Lithium garnet based free-standing solid polymer composite membrane for rechargeable lithium battery

Electrolytes with high lithium-ion conductivity, better mechanical strength and large electrochemical window are essential for the realization of high-energy density lithium batteries. Polymer electrolytes are gaining interest due to their inherent flexibility and nonflammability over conventional liquid electrolytes. In this work, lithium garnet composite polymer electrolyte membrane (GCPEM) consisting of large molecular weight (W_avg ~?5?×?10⁶) polyethylene oxide (PEO) complexed with lithium perchlorate (LiClO₄) and lithium garnet oxide Li_6.28Al_0.24La₃Zr₂O₁₂ (Al-LLZO) is prepared by solution-casting method. Significant improvement in Li⁺ conductivity for Al-LLZO containing GCPEM is observed compared with the Al-LLZO free polymer membrane. Maximized room temperature (30 °C) Li⁺ conductivity of 4.40?×?10^?4 S cm^?1 and wide electrochemical window (4.5 V) is observed for PEO₈/LiClO₄?+?20 wt% Al-LLZO (GCPEM-20) membrane. The fabricated cell with LiCoO₂ as cathode, metallic lithium as anode and GCPEM-20 as electrolyte membrane delivers an initial charge/discharge capacity of 146 mAh g^?1/142 mAh g^?1 at 25 °C with 0.06 C-rate.     

Steady-state polarization measurements of lithium insertion electrodes for high-power lithium-ion batteries

Steady-state polarization measurements of lithium titanium oxide (LTO; Li[Li_1/3Ti_5/3]O₄) were carried out using the 0-V lithium-ion cells consisting of two identical LTO-electrodes with a parallel-plate symmetrical electrode configuration. The sinusoidal voltage with the peak amplitude of 1.0 V was imposed at 0.1 Hz upon the 0-V cells and the current response was measured as a function of time. The steady-state polarization, obtained by plotting the current versus applied voltage, was linear in current up to approximately 60 mA cm^?2 or 4 A g^?1 based on the LTO weight and suggested the resistance polarization only for the lithium insertion electrode of the LTO. The method was also applied to lithium aluminum manganese oxide (LAMO; Li[Li_0.1Al_0.1Mn_1.8]O₄) and the resistance polarization of the LAMO-electrode was determined for currents up to approximately 25 mA cm^?2 or 2 A g^?1 based on the LAMO weight. The validity of the results was examined for the polarization measurements of the 2.5-V lithium-ion battery consisting of LTO and LAMO, and the significance of the polarization measurements of lithium insertion electrodes for high-power applications was discussed.     

Effects of carbon coating from sucrose and PVDF on electrochemical performance of Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript>/C composites in different potential ranges

The carbon coated nanoflower-like Li₄Ti₅O₁₂/C composites were prepared via hydrothermal method followed by surface modification using sucrose or polyvinylidene fluoride (PVDF) as carbon sources. X-ray diffraction, SEM, TEM, Raman spectroscopy, TGA, and the electrochemical measurements were used for the materials characterization. Such modification leads to the formation of a high-conductive carbon coating. In the case of polyvinylidene fluoride use, fluorination of Li₄Ti₅O₁₂ surface takes place also. As a result, electrochemical performance of the obtained composites is improved. In the potential range of 1–3 V, Li₄Ti₅O₁₂, Li₄Ti₅O₁₂/C_PVDF, and Li₄Ti₅O₁₂/C_sucrose exhibit, respectively, the discharge capacities of 142.5, 154.3, and 170.4 mAh/g at a current of 20 mA/g and 57.2, 82.1, and 89.3mAh/g at a current of 3200 mA/g. When cycled in a potential range of 0.01–3 V, the discharge capacity of Li₄Ti₅O₁₂/C_PVDF increases up to 252 mAh/g at 20 mA/g.     

Li4Ti5O12/CMK-3复合材料的制备及其作为锂离子电池负极材料的性能

将LiNO₃和Ti(OC₄H₉)₄填填充在有序介孔碳CMK-3 孔道中, 然后烧结合成了Li₄Ti₅O₁₂/CMK-3复合材料. 利用扫描电子显微镜(SEM)、透射电子显微镜(TEM)和X射线衍射(XRD)对其结构和微观形貌进行了表征. 利用差热-热重分析(TG-DTA)测试复合材料中Li₄Ti₅O₁₂的含量. 利用充放电测试、循环伏安和电化学阻抗技术考察了复合材料作为锂离子电池负极材料的性能. 发现Li₄Ti₅O₁₂分布在CMK-3孔道中及其周围, 复合材料的高倍率充放电性能显著优于商品Li₄Ti₅O₁₂, 复合材料中Li₄Ti₅O₁₂的比容量明显高于除去CMK-3的样品(在1C倍率时比容量为117.8 mAh·g^-1), 其0.5C、1C和5C倍率的放电比容量分别为160、143 和131 mAh·g^-1, 库仑效率接近100%, 5C倍率时循环100次的容量损失率只有0.62%. 本研究结果表明CMK-3明显提高了Li₄Ti₅O₁₂的高倍率充放电性能, 可能是CMK-3特殊的孔道结构和良好的导电性减小了Li₄Ti₅O₁₂的粒径并提高了其电导率.     

Synthesis and electrochemical properties of spinel Li4Ti5O12−x Cl x anode materials for lithium-ion batteries

Li₄Ti₅O_12−x Cl _x (0 ≤ x ≤ 0.3) compounds were synthesized successfully via high temperature solid-state reaction. X-ray diffraction and scanning electron microscopy were used to characterize their structure and morphology. Cyclic voltammetry, electrochemical impedance spectroscopy, and charge/discharge cycling performance tests were used to characterize their electrochemical properties. The results showed that the Li₄Ti₅O_12−x Cl _x (0 ≤ x ≤ 0.3) compounds were well-crystallized pure spinel phase and that the grain sizes of the samples were about 3–8 μm. The Li₄Ti₅O_11.8Cl_0.2 sample presented the best discharge capacity among all the samples and showed better reversibility and higher cyclic stability compared with pristine Li₄Ti₅O₁₂. When the discharge rate was 0.5 C, the Li₄Ti₅O_11.8Cl_0.2 sample presented the superior discharge capacity of 148.7 mAh g⁻¹, while that of the pristine Li₄Ti₅O₁₂ was 129.8 mAh g⁻¹; when the discharge rate was 2 C, the Li₄Ti₅O_11.8Cl_0.2 sample presented the discharge capacity of 120.7 mAh g⁻¹, while that of the pristine Li₄Ti₅O₁₂ was only 89.8 mAh g⁻¹.     

Structural and Electrochemical Study of Vanadium‐Doped TiO2 Ramsdellite with Superior Lithium Storage Properties for Lithium‐Ion Batteries

Titanium‐oxide‐based materials are considered attractive and safe alternatives to carbonaceous anodes in Li‐ion batteries. In particular, the ramsdellite form TiO₂(R) is known for its superior lithium‐storage ability as the bulk material when compared with other titanates. In this work, we prepared V‐doped lithium titanate ramsdellites with the formula Li_0.5Ti_1?xV_xO₂ (0≤x≤0.5) by a conventional solid‐state reaction. The lithium‐free Ti_1?xV_xO₂ compounds, in which the ramsdellite framework remains virtually unaltered, are easily obtained by a simple aqueous oxidation/ion‐extraction process. Neutron powder diffraction is used to locate the Li channel site in Li_0.5Ti_1?xV_xO₂ compounds and to follow the lithium extraction by difference‐Fourier maps. Previously delithiated Ti_1?xV_xO₂ ramsdellites are able to insert up to 0.8 Li⁺ per transition‐metal atom. The initial gravimetric capacities of 270 mAh g^?1 with good cycle stability under constant current discharge conditions are among the highest reported for bulk TiO₂‐related intercalation compounds for the threshold of one e^? per formula unit.     

Preparation of Li4Ti5O12 Microspheres with a Pure Cr2O3 Coating Layer and its Effect for Lithium Storage

The pure Cr₂O₃ coated Li₄Ti₅O₁₂ microspheres were prepared by a facile and cheap solutionbased method with basic chromium(III) nitrate solution (pH=11.9). And their Li-storage properties were investigated as anode materials for lithium rechargeable batteries. The pure Cr₂O₃ works as an adhesive interface to strengthen the connections between Li₄Ti₅O₁₂ particles, providing more electric conduction channels, and reduce the inter-particle resistance. Moreover, LixCr₂O₃, formed by the lithiation of Cr₂O₃, can further stabilize Li₇Ti₅O₁₂ with high electric conductivity on the surface of particles. While in the acid chromium solution (pH=3.2) modification, besides Cr₂O₃, Li₂CrO₄ and TiO₂ phases were also found in the final product. Li₂CrO₄ is toxic and the presence of TiO₂ is not welcome to improve the electrochemical performance of Li₄Ti₅O₁₂ microspheres. The reversible capacity of 1% Cr₂O₃-coated sample with the basic chromium solution modification was 180 mAh/g at 0.1 C, and 134 mAh/g at 10 C. Moreover, it was even as high as 127 mAh/g at 5 C after 600 cycles. At-20℃, its reversible specific capacity was still as high as 118 mAh/g.     

Water-in-oil microemulsion method preparation and capacitance performance study of Li4Mn5O12

Spinel Li₄Mn₅O₁₂ nanoparticles are successfully prepared by water-in-oil microemulsion method and characterized by X-ray diffraction and scanning electron microscopy. The Li₄Mn₅O₁₂ nanoparticles have sphere-like morphology with particle size less than 50 nm. The Li₄Mn₅O₁₂ and activated carbon (AC) were used as electrodes of Li₄Mn₅O₁₂/AC supercapacitor, respectively. The electrochemical capacitance performance of the supercapacitor was investigated by cyclic voltammetry, galvanostatic charge/discharge, and electrochemical impedance spectroscopy. The results showed that the single electrode was able to deliver specific capacitance 252 F g^?1 within potential range 0–1.4 V at a scan rate of 5 mV s^?1 in 1 mol L^?1 Li₂SO₄ solution, and it also showed high coulombic efficiency close to 100%. This material exhibited a good cycling performance.     

Li2MTi6O14 (M=Sr,Ba): new anodes for lithium-ion batteries

Isostructural Li₂MTi₆O₁₄ (M=Sr, Ba) materials, prepared by a solid state reaction method, have been investigated as insertion electrodes for lithium battery applications. These titanate compounds have a structure that consists of a three-dimensional network of corner- and edge-shared [TiO₆] octahedra, 11-coordinate polyhedra for the alkali-earth ions, and [LiO₄] tetrahedra in tunnels that also contain vacant tetrahedral and octahedral sites. Electrochemical data show that these compounds are capable of reversibly intercalating four lithium atoms in a three-stage process between 1.4 and 0.5 V vs. metallic lithium. The electrodes provide a practical capacity of approximately 140 mAh/g; they are, therefore, possible alternative anode materials to the lithium titanate spinel, Li₄Ti₅O₁₂. The lithium intercalation mechanism and crystal structure of Li₂MTi₆O₁₄ (M=Sr, Ba) electrodes are discussed and compared with the electrochemical and structural properties of Li₄Ti₅O₁₂. The area-specific impedance (ASI) of Li/Li₂SrTi₆O₁₄ cells was found to be significantly lower than that of Li/Li₄Ti₅O₁₂ cells.     

Green Template‐Free Synthesis of Hierarchical Shuttle‐Shaped Mesoporous ZnFe2O4 Microrods with Enhanced Lithium Storage for Advanced Li‐Ion Batteries

In the work, a facile and green two‐step synthetic strategy was purposefully developed to efficiently fabricate hierarchical shuttle‐shaped mesoporous ZnFe₂O₄ microrods (MRs) with a high tap density of ～0.85 g cm³, which were assembled by 1D nanofiber (NF) subunits, and further utilized as a long‐life anode for advanced Li‐ion batteries. The significant role of the mixed solvent of glycerin and water in the formation of such hierarchical mesoporous MRs was systematically investigated. After 488 cycles at a large current rate of 1000 mA g^?1, the resulting ZnFe₂O₄ MRs with high loading of ～1.4 mg per electrode still preserved a reversible capacity as large as ～542 mAh g^?1. Furthermore, an initial charge capacity of ～1150 mAh g^?1 is delivered by the ZnFe₂O₄ anode at 100 mA g^?1, resulting in a high Coulombic efficiency of ～76 % for the first cycle. The superior Li‐storage properties of the as‐obtained ZnFe₂O₄ were rationally associated with its mesoprous micro‐/nanostructures and 1D nanoscaled building blocks, which accelerated the electron transportation, facilitated Li⁺ transfer rate, buffered the large volume variations during repeated discharge/charge processes, and provided rich electrode–electrolyte sur‐/interfaces for efficient lithium storage, particularly at high rates.     

Li4Ti5O12/(Ag+C)电极材料的固相合成及电化学性能

以Li₂CO₃,TiO₂为原料,葡萄糖为碳源,采用固相煅烧工艺合成了亚微米级的Li₄Ti₅O₁₂/C复合负极材料。并将之与AgNO₃复合,采用固相方法制备出了Ag表面修饰的Li₄Ti₅O₁₂/(Ag+C)复合材料。采用XRD、SEM和TEM测试方法对材料的微结构进行了表征。结果表明,C的存在对Ag单质在Li₄Ti₅O₁₂/C颗粒表面的大量形成起到了积极的促进作用,从而很大程度地提高了Li₄Ti₅O₁₂/C的电导率,因此有效地改善了其电化学性能。在1C倍率下,Li₄Ti₅O₁₂/(Ag+C)复合材料的首次放电容量达到了164 mAh·g^-1。