Environmentally responsive particles: from superhydrophobic particle films to water-dispersible microspheres

We describe the preparation, by precipitation copolymerization, of multifunctional divinylbenzene-co-pentafluorostyrene microspheres able to produce superhydrophobic surfaces or disperse in aqueous media upon annealing either in air or water, respectively. For that purpose, an amphiphilic block copolymer, polystyrene-b-poly(acrylic acid), was introduced in the initial feed composed of divinylbenzene and 2,3,4,5,6-pentafluorostyrene. As a result, fluorinated particles were obtained in which the diblock copolymer was encapsulated during the polymerization step. Upon annealing in dry air, the particles are completely hydrophobic and form superhydrophobic surfaces. On the contrary, annealing in water induces the reorientation of the PAA groups toward the particle interface, thus the particles can be dispersed in aqueous media. In addition, the presence of carboxylic acid groups at the particle interface permits us to switch the surface charge between negative and neutral depending on the environmental pH.     

Photoinduced Reversible Topographical Changes on Diarylethene Microcrystalline Surfaces with Biomimetic Wetting Properties

Reversible topographical changes were observed on a photochromic diarylethene microcrystalline film surface by alternate irradiation with UV and visible light. Two types of surfaces were prepared from this film: 1) Storage of the film at 30 °C for 24 hours in the dark after UV irradiation afforded a surface that was covered with needle‐shaped crystals, whose diameter and length were approximately 1 μm and 10 μm, respectively, and showed a superhydrophobic lotus effect. 2) Storage of the film at 70 °C for 3 hours in the dark caused the needle‐shaped crystals to be converted into larger rod‐like crystals (5∼8 μm wide and 20∼30 μm long) by Ostwald ripening and a disappearance of the lotus effect. The obtained activation energy of the formation of the needle‐ and rod‐shaped crystals was 143 and 162 kJ mol⁻¹, respectively. Subsequent UV irradiation to the surface, which was followed by storage at 50 °C for 1 hour in the dark, gave a doubly rough structure; small needle‐shaped crystals were formed between the larger rod‐shaped crystals. The surface showed both superhydrophobic properties and the pinned effect of the water droplet: the petal effect. Fractal analysis of both surfaces were carried out using a box‐counting method, and the lotus effect was observed in the presence of smaller‐sized crystals, whilst the petal effect was observed with larger sized crystals (ca. 100 μm). We demonstrated that the hydrophobic property was controlled by the distribution in crystal size of the closed‐ring isomer of the diarylethene. Visible‐light irradiation of both rough surfaces afforded surfaces with cubic‐shaped micro‐crystals of the open‐ring isomer.     

Directional self-cleaning superoleophobic surface

In this work, we report the creation of a grooved surface comprising 3 μm grooves (height ～4 μm) separated by 3 μm from each other on a silicon wafer by photolithography. The grooved surface was then modified chemically with a fluorosilane layer (FOTS). The surface property was studied by both static and dynamic contact angle measurements using water, hexadecane, and a polyethylene wax ink as the probing liquids. Results show that the grooved surface is both superhydrophobic and superoleophobic. Its observed contact angles agree well with the calculated Cassie-Baxter angles. More importantly, we are able to make a replica of the composite wax ink-air interface and study it by SEM. Microscopy results not only show that the droplet of the wax ink "sits" on air in the composite interface but also further reveal that the ink drop actually pins underneath the re-entrant structure in the side wall of the grooved structure. Contact angle measurement results indicate that wetting on the grooved surface is anisotropic. Although liquid drops are found to have lower static and advancing contact angles in the parallel direction, the drops are found to be more mobile, showing smaller hysteresis and lower sliding angles (as compared to the FOTS wafer surface and a comparable 3-μm-diameter pillar array FOTS surface). The enhanced mobility is attributable to the lowering of the resistance against an advancing liquid because 50% of the advancing area is made of a solid strip where the liquid likes to wet. This also implies that the contact line for advancing is no longer smooth but rather is ragged, having the solid strip area leading the wetting and the air strip area trailing behind. This interpretation is supported by imaging the geometry of the contact lines using molten ink drops recovered from the sliding angle experiments in both the parallel and orthogonal directions. Because the grooved surface is mechanically stronger against mechanical abrasion, the self-cleaning effect exhibited in the parallel direction suggests that groove texturing is a viable approach to create mechanically robust, self-cleaning, superoleophobic surfaces.     

A vertical microfluidic probe

Performing localized chemical events on surfaces is critical for numerous applications. We earlier invented the microfluidic probe (MFP), which circumvented the need to process samples in closed microchannels by hydrodynamically confining liquids that performed chemistries on surfaces (Juncker et al. Nat. Mater. 2005, 4, 622-628). Here we present a new and versatile probe, the vertical MFP (vMFP), which operates in the scanning mode while overcoming earlier challenges that limited the practical implementation of the MFP technology. The key component of the vMFP is the head, a microfluidic device (～1 cm(2) in area) consisting of glass and Si and having microfluidic features fabricated in-plane in the Si layer. The base configuration of the head has two micrometer-size channels that inject/aspirate liquids and terminate at the apex which is ～1 mm(2). In scanning mode, the head is oriented vertically with the apex parallel to the surface with typical spacing of 1-30 μm. Such length scales and using flow rates from nanoliters/second to microliters/second allow chemical events to be performed on surfaces with tens of picoliter quantities of reagents. Before scanning, the head is clipped on a holder for leak-free, low dead volume interface assembly, providing a simple world-to-chip interface. Surfaces are scanned by mounting the holder on a computer-controlled stage having ～0.1 μm resolution in positioning. We present detailed steps to fabricate vMFP heads having channels with dimensions from 1 μm × 1 μm to 50 μm × 50 μm for liquid localization over areas of 10-10,000 μm(2). Additionally, advanced design strategies are described to achieve high yield in fabrication and to support a broad range of applications. These include particulate filters, redundant aperture architectures, inclined flow-paths that service apertures, and multiple channels to enable symmetric flow confinement. We also present a method to characterize flow confinement and estimate the distance between the head and the surface by monitoring the evolution of a solution of fluorescently labeled antibody on an activated glass surface. This flow characterization reveals regimes of operation suitable for different surface topographies. We further integrate the dispensing of immersion liquid to the vMFP head for processing surfaces for extended periods of time (～60 min). The versatility of the vMFP is exemplified by patterning fluorescently labeled proteins, inactivation of cells using sodium hypochlorite, and staining living NIH fibroblasts with Cellomics. These applications are enabled by the compact design of the head, which provides easy access to the surface, simplifies alignment, and enables processing surfaces having dimensions from the micrometer to the centimeter scale and with large topographical variations. We therefore believe that ease-of-operation, reconfigurability, and conservative use of chemicals by the vMFP will lead to its widespread use by microtechnologists and the chemical and biomedical communities.     

Emulsion of aqueous-based nonspherical droplets in aqueous solutions by single-chain surfactants: templated assembly by nonamphiphilic lyotropic liquid crystals in water

Single-chain surfactants usually emulsify and stabilize oily substances into droplets in an aqueous solution. Here, we report a coassembly system, in which single types of anionic or non-ionic surfactants emulsify a class of water-soluble nonamphiphilic organic salts with fused aromatic rings in aqueous solutions. The nonamphiphilic organic salts are in turn promoted to form droplets of water-based liquid crystals (chromonic liquid crystals) encapsulated by single-chain surfactants. The droplets, stabilized against coalescence by encapsulated in a layer (or layers) of single chain surfactants, are of both nonspherical tactoid (elongated ellipsoid with pointy ends) and spherical shapes. The tactoids have an average long axis of ～9 μm and a short axis of ～3.5 μm with the liquid crystal aligning parallel to the droplet surface. The spherical droplets are 5-10 μm in diameter and have the liquid crystal aligning perpendicular to the droplet surface and a point defect in the center. Cationic and zwitterionic surfactants studied in this work did not promote the organic salt to form droplets. These results illustrate the complex interplay of self-association and thermodynamic incompatibility of molecules in water, which can cause new assembly behavior, including potential formation of vesicles or other assemblies, from surfactants that usually form only micelles. These unprecedented tactoidal shaped droplets also provide potential for the fabrication of new soft organic microcapsules.     

Mimicking the stenocara beetle--dewetting of drops from a patterned superhydrophobic surface

This paper describes the preparation of superhydrophobic surfaces that have been selectively patterned with circular hydrophilic domains. These materials mimicked the back of the stenocara beetle and collected drops of water if exposed to mist or fog. Under the effect of gravity, the drops dewetted from the hydrophilic regions once a critical volume had been reached. The surface energy in the hydrophilic regions was carefully controlled and assumed various values, allowing us to study the behavior of drops as a function of the superhydrophobic/hydrophilic contrast. We have investigated the development of drops and quantitatively analyzed the critical volumes as a function of several parameters.     

Comparison of the performance characteristics of two tubular contactless conductivity detectors with different dimensions and application in conjunction with HPLC

Two tubular capacitively coupled contactless conductivity detection (C(4)D) cells with different geometric dimensions were evaluated with regard to their main analytical characteristics under non-separation and separation conditions in conjunction with liquid chromatography. A comparison of the performance of the tubular cells to a previously tested thin-layer detection cell was drawn. Additionally, using a theoretical model the experimental results were compared with sets of calculated values and partially enabled to model the complex behavior of C(4)D detection in combination with high-performance liquid chromatography (HPLC). While cell 1 is characterized by a geometric cell volume of 0.6 μL, a wall thickness of 675 μm, and an inner diameter of 125 μm, the respective values for cell 2 are 2.3 μL, 200 μm, and 250 μm. The main analytical parameters were evaluated using a potassium chloride (KCl) solution. The limits of detection were 0.4 μM KCl (5.7 × 10(-6) S m(-1)) for cell 1 and 0.2 μM KCl (3.2 × 10(-6) S m(-1)) for cell 2, which compares well to the previously found 0.2 μM for the thin-layer cell. A pair of linear ranges was found for both cells in a concentration interval ranging from 1 × 10(-6) to 1 × 10(-4) M (corresponding to 1.5 × 10(-5) to 1.5 × 10(-3) S m(-1)) KCl, respectively. Furthermore, the detector cells were applied to the HPLC separation of a model compound system consisting of benzoic acid, lactic acid, octanesulphonic acid, and sodium capronate. Separation of the compounds was achieved with a Biospher PSI 100 C18 column using 60% aqueous acetonitrile mobile phase. Calibration curves for the examined model system were well correlated (r2 > 0.997), and it was found that under separation conditions the arrangement with the lower cell volume (cell 1) yields higher sensitivity and respectively lower limits of detection for all model compounds. Compared with the thin-layer cell, the tubular cells show better overall performance in regard to the determined analytical characteristics.     

Fabrication, surface properties, and origin of superoleophobicity for a model textured surface

Inspired by the superhydrophobic effect displayed in nature, we set out to mimic the interplay between the chemistry and physics in the lotus leaf to see if the same design principle can be applied to control wetting and adhesion between toners and inks on various printing surfaces. Since toners and inks are organic materials, superoleophobicity has become our design target. In this work, we report the design and fabrication of a model superoleophobic surface on silicon wafer. The model surface was created by photolithography, consisting of texture made of arrays of ～3 μm diameter pillars, ～7 μm in height with a center-to-center spacing of 6 μm. The surface was then made oleophobic with a fluorosilane coating, FOTS, synthesized by the molecular vapor deposition technique with tridecafluoro-1,1,2,2-tetrahydrooctyltrichlorosilane. Contact angle measurement shows that the surface exhibits super repellency toward water and oil (hexadecane) with a water and hexadecane contact angles at 156° and 158°, respectively. Since the sliding angles for both liquids are also very small (～10°), we conclude that the model surface is both superhydrophobic and superoleophobic. By comparing with the contact angle data of the bare silicon surfaces (both smooth and textured), we also conclude that the superoleophobicity is a result of both surface texturing and fluorination. Results from investigations of the effects of surface modification and pillar geometry indicate that both surface oleophobicity and pillar geometry are contributors to the superoleophobicity. More specifically, we found that superoleophobicity can only be attained on our model textured surface when the flat surface coating has a relatively high oleophobicity (i.e., with a hexadecane contact angle of >73°). SEM examination of the pillars with higher magnification reveals that the side wall in each pillar is not smooth; rather it consists of a ～300 nm wavy structure (due to the Bosch etching process) from top to bottom. Comparable textured surfaces with (a) smooth straight side wall pillars and (b) straight side wall pillars with a 500 nm re-entrant structure made of SiO(2) were fabricated and the surfaces were made oleophobic with FOTS analogously. Contact angle data indicate that only the textured surfaces with the re-entrant pillar structure are both superoleophobic and superhydrophobic. The result suggests that the wavy structure at the top of each pillar is the main geometrical contributor to the superoleophobic property observed in the model surface.     

Modeling droplets on superhydrophobic surfaces: equilibrium states and transitions

We present a lattice Boltzmann solution of the equations of motion describing the spreading of droplets on topologically patterned substrates. We apply it to model superhydrophobic behavior on surfaces covered by an array of micrometer-scale posts. We find that the patterning results in a substantial increase in contact angle, from 110 degrees to 156 degrees. The dynamics of the transition from drops suspended on top of the posts to drops collapsed in the grooves is described.     

Modeling contact angle hysteresis on chemically patterned and superhydrophobic surfaces

We investigate contact angle hysteresis on chemically patterned and superhydrophobic surfaces, as the drop volume is quasistatically increased and decreased. We consider both two (cylindrical drops) and three (spherical drops) dimensions using analytical and numerical approaches to minimize the free energy of the drop. In two dimensions, we find, in agreement with other authors, a slip, jump, stick motion of the contact line. In three dimensions, this behavior persists, but the position and magnitude of the contact line jumps are sensitive to the details of the surface patterning. In two dimensions, we identify analytically the advancing and receding contact angles on the different surfaces, and we use numerical insights to argue that these provide bounds for the three-dimensional cases. We present explicit simulations to show that a simple average over the disorder is not sufficient to predict the details of the contact angle hysteresis and to support an explanation for the low contact angle hysteresis of suspended drops on superhydrophobic surfaces.     

Existence and stability of new nanoreactors: highly swollen hexagonal liquid crystals

We report the preparation of direct hexagonal liquid crystals, constituted of oil-swollen cylinders arranged on a triangular lattice in water. The volume ratio of oil over water, rho can be as large as 3.8. From the lattice parameter measured by small-angle X-ray scattering, we show that all the oil is indeed incorporated into the cylinders, thus allowing the diameter of the cylinders to be controlled over one decade range, provided that the ionic strength of the aqueous medium and rho are varied concomitantly. These hexagonal swollen liquid crystals (SLCs) have been first reported with sodium dodecyl sulfate as anionic surfactant, cyclohexane as solvent, 1-pentanol as co-surfactant, and sodium chloride as salt (Ramos, L.; Fabre, P. Langmuir 1997, 13, 13). The stability of these liquid crystals is investigated when the pH of the aqueous medium or the chemical nature of the components (salt and surfactant) is changed. We demonstrate that the range of stability is quite extended, rendering swollen hexagonal phases potentially useful for the fabrication of nanomaterials. As illustrations, we finally show that gelation of inorganic particles in the continuous aqueous medium of a SLC and polymerization within the oil-swollen cylinders of a SLC can be conducted without disrupting the hexagonal order of the system.     

Preparation of superhydrophobic nanocalcite crystals using Box–Behnken design

Superhydrophobic nanocalcite crystals were prepared via an adjusted aqueous reaction of CaO, CO₂ gas and sodium oleate. Box–Behnken design was used to optimize the preparation parameters such as CaO concentration, CO₂ gas flow rate and surfactant concentration. The results revealed that the produced CaCO₃ is indexed to the calcite phase. The crystallite size, particle size, morphology, hydrophobicity and surface charge of CaCO₃ are significantly affected by changing the preparation parameters. The addition of sodium oleate helps in reducing the crystallite size from 101 nm to 48 nm, reducing the particle size from 1.5 μm length scalenohedral particles to 40 nm rhombohedral particles and modifying the properties of pure CaCO₃ from highly hydrophilic to superhydrophobic.     

Superhydrophobicity of biological and technical surfaces under moisture condensation: stability in relation to surface structure

The stability of superhydrophobic properties of eight plants and four technical surfaces in respect to water condensation has been compared. Contact and sliding angles were measured after application of water drops of ambient temperature (20 degrees C) onto cooled surfaces. Water evaporating from the drops condensed, due to the temperature difference between the drops and the surface, on the cooled samples, forming "satellite droplets" in the vicinity of the drops. Surface cooling to 15, 10, and 5 degrees C showed a gradual decrease of superhydrophobicity. The decrease was dependent on the specific surface architecture of the sample. The least decrease was found on hierarchically structured surfaces with a combination of a coarse microstructure and submicrometer-sized structures, similar to that of the Lotus leaf. Control experiments with glycerol droplets, which show no evaporation, and thus no condensation, were carried out to verify that the effects with water were caused by condensation from the drop (secondary condensation). Furthermore, the superhydrophobic properties after condensation on cooled surfaces from a humid environment for 10 min were examined. After this period, the surfaces were covered with spherical water droplets, but most samples retained their superhydrophobicity. Again, the best stability of the water-repellent properties was found on hierarchically structured surfaces similar to that of the Lotus leaf.     

N-乙基壳聚糖的针状结晶

在N 乙基壳聚糖的甲酸溶液浇铸膜中观察到高分子少有的针状晶体 .从球晶经后结晶得到的针状晶体为长条矩形 ,典型尺寸为～ 5 0 μm× 2～ 5 μm× 1～ 2 μm ,高分子链平行于晶体长轴 .针状晶体首先出现在球晶的核心处 ,继而出现在球晶微纤每个树枝状分叉处 ,最后才遍布球晶各处 .针状晶体可以看成是高分子伸直链结晶的一种 .浇铸膜吸潮实际上形成了超浓溶液 (浓度 >80wt% ) ,从而分子链可以运动而后结晶成针状晶体     

反胶束萃取-高效液相色谱法测定磺酸型偶氮染料

建立了水中磺酸偶氮染料甲基橙（MO）、刚果红（CR）和酸性铬兰K（ACBK）的反胶束萃取-离子对高效液相色谱定量检测的方法。采用Hypersil C18柱（250×4．6mm,5μm）,流动相为V（甲醇）／V（水）=63：37（含10mmol／L的KH2PO4、4mmol／L的四丁基溴化铵,KOH调pH=7．0）,流速为0.8mL／min,MO、CR和ACBK检测波长分别为449nm、505nm和526nm。结果表明,染料的回收率为92．9％～102．1％,相对标准偏差为0．9％～2．3％,水中MO、CR和ACBK的检出限分别为0．6μg／L、1．2μg／L和1．3μg／L。     

Numerical analysis of the shapes and energies of droplets on micropatterned substrates

The shapes and energies of drops on substrates patterned with either holes or posts are computed using Surface Evolver software. The holes and posts are cylindrical in shape and distributed in a 6-fold symmetric pattern. The wetting conditions are such that the liquid does not fill the holes and the interface between the drop and the substrate is composite, i.e., partly solid/liquid and partly liquid/vapor. The sequence of stable drop configurations with increasing volume is analyzed and provides, in part, an explanation for superhydrophobic drop spreading.     

Dissipative crystallization of sodium salts of carboxymethyl cellulose

Drying dissipative patterns were observed at room temperature on a cover glass, a watch glass, and a Petri glass dish during the course of dryness of aqueous solution of sodium salts of carboxymethyl cellulose (NaCMC) having different molecular weights in the presence of sodium chloride and in their absence. Without salt, the polymers were slightly hygroscopic and did not dry up completely on the substrates. Single crystals of the NaCMC without salt were short rodlike and quite similar to those of the other polysaccharides studied hitherto, i.e., hydroxypropyl cellulose and sodium dextran sulfate. Morphology of the polymer crystals were short rods, long dendritic rods, and/or hedrite assemblies depending on location in the dried film and in the presence of sodium chloride. Spoke-like orientation of the long dendritic rods appeared on a cover glass and a watch glass especially for NaCMC of low molecular weights.     

Decoupling of the liquid response of a superhydrophobic quartz crystal microbalance

Recent reports using particle image velocimetry and cone-and-plate rheometers have suggested that a simple Newtonian liquid flowing across a superhydrophobic surface demonstrates a finite slip length. Slippage on a superhydrophobic surface indicates that the combination of topography and hydrophobicity may have consequences for the coupling at the solid--liquid interface observed using the high-frequency shear-mode oscillation of a quartz crystal microbalance (QCM). In this work, we report on the response of a 5 MHz QCM possessing a superhydrophobic surface to immersion in water--glycerol mixtures. QCM surfaces were prepared with a layer of SU-8 photoresist and lithographically patterned to produce square arrays of 5 mum diameter circular cross-section posts spaced 10 microm center-to-center and with heights of 5, 10, 15, and 18 microm. Non-patterned layers were also created for comparison, and both non-hydrophobized and chemically hydrophobized surfaces were investigated. Contact angle measurements confirmed that the hydrophobized post surfaces were superhydrophobic. QCM measurements in water before and after applying pressure to force a Cassie-Baxter (non-penetrating) to Wenzel (penetrating) conversion of state showed a larger frequency decrease and higher dissipation in the Wenzel state. QCM resonance spectra were fitted to a Butterworth-van Dyke model for the full range of water-glycerol mixtures from pure water to (nominally) pure glycerol, thus providing data on both energy storage and dissipation. The data obtained for the post surfaces show a variety of types of behavior, indicating the importance of the surface chemistry in determining the response of the quartz crystal resonance, particularly on topographically structured surfaces; data for hydrophobized post surfaces imply a decoupling of the surface oscillation from the mixtures. In the case of the 15 microm tall hydrophobized post surfaces, crystal resonance spectra become narrower as the viscosity-density product increases, which is contrary to the usual behavior. In the most extreme case of the 18 microm tall hydrophobized post surfaces, both the frequency decrease and bandwidth increase of the resonance spectra are significantly lower than that predicted by the Kanazawa and Gordon model, thus implying a decoupling of the oscillating surface from the liquid, which can be interpreted as interfacial slip.     

Growth dynamics of water drops on a square-pattern rough hydrophobic surface

Condensation on rough or superhydrophobic substrates can induce wetting behavior that is quite different from that of deposited or impinging drops. We investigate the growth dynamics of water drops in a well-controlled condensation chamber on a model rough hydrophobic surface made of square pillars. After having followed growth laws similar to those observed on flat surfaces, a transition to an air-pocket-like state occurred because of the bridging of the drops between the pillars. Another transition to the more stable Wenzel state is later ensured by a noticeable pillar self-drying process. Condensation ends up in a few large drops in a mixed Wenzel penetration regime. The drops are fed by neighboring channels and the adjacent pillars stay almost dry, a remarkable and seemingly general property of rough hydrophobic substrates.     

Complexation-mediated crystallization. Crystallization of sodium acetate trihydrate needles from cyclohexane solution

The phenomenon of complexation-mediated crystallization is introduced and proposed as a new means for the preparation of novel forms of materials. Attempted crystallization of complexes of salts with crown ethers often results in the precipitation of the uncomplexed salt rather than the complex. In this study, a solution of the 15-crown-5 complex of sodium acetate in cyclohexane precipitated uncomplexed sodium acetate trihydrate as single crystals. The crystal morphology (long needles) of this crystalline sodium acetate stands in sharp contrast to the hexagonal plates known to form from aqueous solution. X-ray diffraction analysis revealed that sodium acetate as crystallized from cyclohexane solution adopted a crystal lattice identical to that in sodium acetate crystallized from aqueous solution. Possible origins of the change in crystal morphology are discussed.