Controllable synthesis of titania/reduced graphite oxide nanocomposites with various titania phase compositions and their photocatalytic performance

A facile method is presented for preparing TiO2 /reduced graphite oxide(RGO) nanocomposites with phase-controlled TiO2 nanoparticles via redox reaction between the reductive titanium(Ⅲ) precursor and graphite oxide(GO),and a series of TiO2 /RGO composites with various TiO2 phase compositions were obtained.In all the titania/RGO composites,the TiO2 nanoparticles were uniformly distributed on the surface of the RGO.The TiO2 consisted of anatase phase particles in the form of square-plates with edges less than 10 nm and the rutile phase nanorods in diameters less than 10 nm.The performances of the as-prepared TiO2 /RGO composites were investigated on catalytically degrading phenol under visible light irradiation.The TiO2 /RGO composites can effectively degrade phenol under visible light irradiation,and the phase composition of TiO2 in the composites significantly influences the activities of these catalysts.     

Exfoliated graphite nanoplatelets and gold nanoparticles based electrochemical sensor for determination of levodopa

This paper describes a rapid, accurate, and sensitive method for the determination of levodopa in a pharmaceutical sample using a glassy carbon electrode modified with a hybrid nanocomposite constituted of exfoliated graphite nanoplatelets dispersed in a suspension of gold nanoparticles in carboxymethylcelullose (AuNP-CMC-xGnP/GCE). The nanocomposite was characterized by scanning electron microscopy, transmission electron microscopy, UV-Vis spectroscopy, and zeta potential. Electrochemical characterization of the proposed sensor by cyclic voltammetry and electrochemical impedance spectroscopy indicated that the nanocomposite used for the electrode modification facilitated electron transfer. Using square-wave voltammetry (SWV) under optimized conditions (0.50% (m/v) of AuNP-CMC-xGnP, 0.1 mol L^?1 sulfuric acid, frequency 30 Hz, pulse amplitude 50 mV, and scan increment 6.0 mV), the calibration curve showed a linear range for levodopa from 5 to 50 μmol L^?1, with a limit of detection of 0.5 μmol L^?1. The sensor demonstrated good repeatability and electrode-to-electrode repeatability, with relative standard deviations of 2 and 4%, respectively. The proposed method was successfully applied to quantify levodopa in a pharmaceutical sample by SWV, showing good accuracy. Recoveries of 98 to 107% demonstrated that the method is suitable for practical applications. Therefore, the proposed sensor represents a useful tool for rapid and accurate determination of levodopa.     

The photocatalytic activity of TiO2 foam and surface modified binary oxide titania nanoparticles

Surface modified titania dioxide composite nanoparticles prepared by hydrogen reduction reaction and a mesoporous TiO₂ foam made from a surface modifier and a long chain organic surfactant were characterized by diffractive, spectroscopic and microscopic techniques and studied for their catalytic activity towards the decomposition of an industrial water pollutant, methyl orange. The surface deposition of ruthenium and silicon particles improved the photocatalytic activity of the composite particles resulting in a faster decomposition of the methyl orange compared to commercial TiO₂ alone. Modification of TiO₂ with RuO₂ only offered a marginal benefit over TiO₂ while the incorporation of RuO₂ and SiO₂ into TiO₂ resulted in a marked increase in the rate constant and catalytic activity. These results are consistent with the enhanced surface properties of the composite materials resulting from the modification of TiO₂ with RuO₂ and SiO_2. This surface enhancement effects appear synergetic to the charge separation process and hence the photocatalytic results are explained on the basis of a mechanism involving efficient charge transfer across the interfaces of the composites involving photogenerated electron–hole pairs. Results obtained in this study show that the percentage degradation after 1 h of illumination was 47.15% for TiO₂ foam, 75.5 and 106.4%, respectively, for TiO₂/RuO₂ (SiO₂ 5%, w/w) and TiO₂/RuO₂(SiO₂ 10%, w/w) and 34.15% for commercial TiO₂.     

碳化钨-石墨烯插层复合物的制备及作为甲醇氧化助催化剂的性能研究

直接甲醇燃料电池(DMFCs)作为一种环境友好、高效的新能源,对解决世界目前面临的“能源危机”与“环境危机”这两大问题有着至关重要的意义,具有较广阔的应用前景.目前,甲醇氧化催化剂仍然以 Pt基为主,但是 Pt价格昂贵,且容易受甲醇氧化中间产物的毒化,从而影响了 DMFCs的商业化进程.碳化钨(WC)作为非贵金属催化剂,在催化方面具有类铂的性能.在 WC上负载适量的 Pt,可以通过两者的协同效应加强催化剂的抗 CO中毒能力.但是,由于 WC的导电性能不佳,比表面积较小,因此寻找合适的载体显得尤为必要.在碳载体中,石墨烯(RGO)具有优良的导电性以及独特的片层结构,是电催化剂的理想载体.以 RGO为载体, WC为插层物质制备的 WC-RGO插层复合物具有化学稳定性好、电导率高且电化学活性面积大等优势.但是,由于石墨烯表面光滑且呈惰性,同时使用传统的碳化方法制备的碳化钨颗粒较大,因此,制备较小颗粒且分散均匀的 WC-RGO插层复合物具有较大难度.一般以偏钨酸铵和氧化石墨烯(GO)为前驱体制备 WC-RGO插层复合物,但是由于偏钨酸根和 GO都带负电,因此不能成功地将偏钨酸根引入到石墨烯的片层结构中,造成 WC-RGO插层复合物组装上的困难.本文采用硫脲成功地合成了具有高分散性 WC纳米颗粒插层在少层 RGO里的 WC-RGO插层复合物.硫脲((NH2)2CS)作为阴离子接受器,具有较强的结合阴离子形成稳定复合物的能力,同时它也是合成具有片层结构的过渡金属硫化物的原料之一.因此在 WC-RGO插层复合物组装过程中,硫脲既作为锚定及诱导剂,又是制备片层二硫化钨(WS2)的硫源.材料具体制备方法如下：首先利用浸渍法,将偏钨酸根阴离子([H2W12O40]6?)牵引到(NH2)2CS改性过的 GO上形成[H2W12O40]6?-(NH2)2CS-GO前驱体;然后将前驱体放入管式炉中还原碳化,前驱体先反应生成 WS2;由于 WS2自身的2D片层结构,反应中可以得到 WS2-RGO插层复合物,接着原位碳化生成 WC-RGO插层复合物.碳化钨-石墨烯负载铂电催化剂(Pt/WC-RGO)通过微波辅助法制得,并采用 X射线衍射、扫描电子显微镜、透射电子显微镜及激光拉曼光谱等手段对其结构与形貌进行了表征.结果显示,在 WC-RGO插层复合物中, WC的平均粒径为1.5 nm, RGO的层数约为5层.在甲醇电氧化反应中,相比于商用 Pt/C催化剂, Pt/WC-RGO插层复合物催化剂具有更高的电化学活性面积(ECSA)和较高的峰电流密度(246.1 m2/g Pt,1364.7 mA/mg Pt),分别是 Pt/C的3.66和4.77倍.我们分别利用 CO溶出伏安法、计时电流法及加速耐久性试验法验证了 Pt/WC-RGO催化剂优秀的抗 CO中毒能力及稳定性. Pt/WC-RGO催化剂特殊的插层结构,在增加 WC与 Pt接触机会以加强协同作用的同时,促进了催化过程中质量及电荷的转移,因而具有比 Pt/C更高的催化活性.可见,通过制备WC-RGO插层复合物可降低 Pt用量,从而大大地降低燃料电池中电催化剂的成本.同时,我们使用的是一种高效,可大批量生产纳米材料的方法,有助于催化剂的商业化.     

Preparation, phase transformation and photocatalytic activities of cerium-doped mesoporous titania nanoparticles

Cerium-doped mesoporous TiO₂ nanoparticles with high surface area and thermal stable anatase wall were synthesized via hydrothermal process in a cetyltrimethylammonium bromide (CTAB)/Ti(SO₄)₂/Ce(NO₃)₄/H₂O system. The obtained materials were characterized by XRD, FESEM, HRTEM, FTIR spectroscopy, nitrogen adsorption and DRS spectra. Experimental results indicated that the doping of cerium not only increased the surface area of mesoporous TiO₂ nanoparticles, but also inhibited the mesopores collapse and the anatase-to-rutile phase transformation. Moreover, the undoped, doped anatase mesoporous nanoparticles exhibit higher photocatalytic activity than commercial photocatalyst (Degussa, P25), but the maximum photodegradation rate corresponds to the undoped mesoporous TiO₂ nanoparticles. The lower photocatalytic activities of cerium-doped samples compared with undoped one may be ascribed to that the doped cerium partially blocks titania's surface sites available for the photodegradation and absorption of Rhodamine B (RB).     

Partially reduced graphite oxide as an electrode material for electrochemical double-layer capacitors

Partially reduced graphite oxide was prepared from graphite oxide by using synthetic graphite as precursor. The reduction of graphite oxide with a layer distance of 0.57?nm resulted in a reduction of the layer distance depending on the degree of reduction. Simultaneously the amount of oxygen functionalities in the graphite oxide was reduced, which was corroborated by elemental analysis and EDX. The electrochemical activation of the partially reduced graphite oxide was investigated for tetraethylammonium tetrafluoroborate in acetonitrile and in propylene carbonate. The activation potential depends significantly on the degree of reduction, that is, on the graphene-layer distance and on the solvent used. The activation potential decreased with increasing layer distance for both positive and negative activation. The resulting capacitance after activation was found to be affected by the layer distance, the oxygen functionalities and the used electrolyte. For a layer distance of 0.43?nm and with acetonitrile as the solvent, a differential capacitance of 220?Fg(-1) was achieved for the discharge of the positive electrode near the open-circuit potential and 195?Fg(-1) in a symmetric full-cell assembly.     

Cuprous oxide nanoparticles dispersed on reduced graphene oxide as an efficient electrocatalyst for oxygen reduction reaction

Cuprous oxide (Cu(2)O) nanoparticles dispersed on reduced graphene oxide (RGO) were prepared by reducing copper acetate supported on graphite oxide using diethylene glycol as both solvent and reducing agent. The Cu(2)O/RGO composite exhibits excellent catalytic activity and remarkable tolerance to methanol and CO in the oxygen reduction reaction.     

High Photocatalytic Properties of Zinc OxideNanoparticles with Amidoximated BacterialCellulose Nanofibers as Templates简

The freshly prepared water-wet amidoximated bacterial cellulose （Am-BC） serves as an effective nanoreactor to synthesis zinc oxide nanoparticles by in situ polyol method. The obtained ZnO/Am-BC nanocomposites have been characterized by field emission scanning electron microscopy （FE-SEM）, X-ray diffraction （XRD）, Fourier transformed infrared spectroscopy （FTIR） and thermogravimetric analysis （TGA）. The influence of the zinc acetate concentration on the morphologies and size ofZnO nanoparticles and the possible formation mechanism were discussed. The results indicated that uniform ZnO nanoparticles were homogeneously anchored on the Am-BC nanofibers through strong interaction between the hydroxyl and amino groups of Am-BC and ZnO nanoparticles. The loading content of ZnO nanoparticles is higher using Am-BC as a template than using the unmodified bacterial cellulose. The resultant nanocomposite synthesized at 0.05 wt% shows a high photocatalytic activity （92%） in the degradation of methyl orange.     

PdCu alloy anchored defective titania for photocatalytic conversion of carbon dioxide into methane with 100% selectivity

The photoreduction of CO₂ into CH₄ with simultaneous high activity and selectivity is a promising strategy to increase energy supply and alleviate global warming.However,the absence of the active sites that is responsible for the adsorption and activation of CO₂ and the generation of CO and H₂ via side reactions often lead to poor efficiency and low selectivity of the catalyst.Herein,Cu,Pd,and PdCu metal clusters cocatalyst-anchored defective TiO_2...     

先进蛋黄-蛋壳结构能源转化纳米反应器

蛋黄-蛋壳结构独特的纳米结构及特性,使其在很多领域中具有潜在的应用价值,因此近年来受到了广泛关注.本综述总结了使用蛋黄-蛋壳纳米结构作为纳米反应器的研究进展.从合成策略出发,主要强调最近五年合成蛋黄-蛋壳纳米结构的最新研究进展.通过光催化,甲烷重整和电催化等反应作为典型的反应过程,重点讨论蛋黄-蛋壳结构纳米反应器在催化领域的应用,并对该领域未来的发展进行了展望.     

Magnetically separable tea leaf mediated nickel oxide nanoparticles for excellent photocatalytic activity

Synthesis of nanoparticles having low chemical toxicity has been interest of researchers for decades. Utilization of plant phytochemicals as reducing agent is now a globally recognized alternative technique for environmental friendly and low-cost production of nanoparticles. This work reports a facile green synthesis protocol of Nickel Oxide nanoparticles (NiO NPs) using fresh tea leaf extract. The synthesized nanoparticles have been characterized through various analytical techniques like Powder XRD (P-XRD), Fourier Transform Infrared Spectroscopy (FT-IR), Transmission electron microscopy (TEM), Scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). The XRD results reveal the formation of crystalline nickel oxide nanoparticles. FTIR spectrum displays the existence of different polyphenolic groups over NiO NPs surface. TEM and SEM images indicate the formation of slightly agglomerated spherical nanoparticles with particle size 3–5 ​nm. The nanoparticles were used towards the photocatalytic degradation of both cationic, anionic dyes and their mixtures under optimum conditions in the presence of UV light irradiation. More than 95% degradation was observed for all the dye solutions with 30 ​mg ​L^-1 catalytic dose. Moreover, the degradation efficiency of the nanoparticle was studied by altering various parameters like pH, initial dye concentration and amount of catalytic dose. Pseudo first order kinetic model was employed in all the reactions. A detailed mechanism and kinetics of the all the reactions were studied. Interestingly, the catalyst showed excellent recyclability up-to 4th cycles with very low catalytic activity loss.     

Simultaneously photodeposited rhodium metal and oxide nanoparticles promoting photocatalytic hydrogen production

Photodeposition of a Rh cocatalyst under atmospheric conditions could simultaneously provide both Rh metal and oxide nanoparticles on a K(2)Ti(6)O(13) photocatalyst, both of which cooperatively promoted the photocatalytic hydrogen production from water and methane.     

Role of bio-derived zinc oxide nanoparticles in antifungal and photocatalytic activities

Research on Chemical Intermediates - Zinc oxide nanoparticles (ZnO-NPs) are known as a material in the treatment of environmental pollutions. In this study, ZnO-NPs were synthesized using...     

Recent advances in suppressing the photocorrosion of cuprous oxide for photocatalytic and photoelectrochemical energy conversion

The emergence of cuprous oxide (Cu₂O) as a visible light active semiconductor for photocatalytic and photoelectrochemical applications has elevated significantly over the past decade. With photocorrosion identified as a severe issue for Cu₂O, its photoactivity has been greatly restricted. Given that Cu₂O redox potentials are located in between its band gap, the possible occurrence of self-photoreduction or self-oxidation upon illumination is inevitable. Various efforts have been directed to implement effective strategies in enhancing the photostability of Cu₂O. In particular, most of the studies focused on improving the charge transfer from Cu₂O to reactants or co-catalyst to avoid accumulation of charge within the particles. This review presents recent research progresses for the development of strategies to suppress Cu₂O photocorrosion in regards to its intrinsic properties and charge kinetics. It is shown that effective transport of electrons or holes out of Cu₂O photocatalyst by engineering its crystal structure, tuning its reaction environment or depositing secondary elements could effectively inhibit Cu₂O from experiencing self-photodecomposition. Understanding of the charge dynamics with respect to its photocorrosion is pivotal to optimize the design of Cu₂O photocatalyst for enhanced performance in the future.     

Electrospun copper oxide nanoparticles as an efficient heterogeneous catalyst for N-arylation of indole

The N-arylation of indoles with a variety of aryl bromides is reported using copper oxide nanoparticles as a heterogeneous catalyst. These copper oxide nanoparticles, which were produced in a novel, facile, and scalable fashion via an electrospinning technique, resulted in an excellent product yield under mild conditions. Moreover, the catalyst was easily recovered and reused several times without significant loss of activity.     

Manganese oxide nanoparticles supported on graphene oxide as an efficient nanocatalyst for the synthesis of 1,2,4-oxadiazoles from aldehydes

The easy synthesis of graphene oxide (GO)-supported manganese dioxide (MnO₂) nanoparticles as a stable heterogeneous nanocatalyst (MnO₂@GO) is described. This catalyst was investigated in the synthesis of 1,2,4-oxadiazoles from amidoximes and aldehydes via a cyclization and oxidation process. The nanocomposite was prepared and characterized using various techniques. The catalytic application of the nanocomposite was examined in the reaction of a variety of aldehydes with aliphatic and aromatic amidoximes. The stable and robust catalyst was recycled for seven consecutive runs without a significant decrease in the catalytic activity.     

Effect of UV and visible light on photocatalytic reduction of lead and cadmium over titania based binary oxide materials

Uniform sized silica and zirconia mixed titania samples were prepared in presence of a surfactant (CETAB) using controlled hydrolysis of corresponding metal alkoxides. Photocatalytic activity towards reduction of lead and cadmium metal in aqueous solution was evaluated both in UV and visible light in a 100 ml capacity reactor. In particular mixing of 10 wt% silica with titania not only increases the surface area of the material but also increases the photocatalytic activity in UV light. Whereas mixing of zirconia with titania proved to be beneficial for visible light reaction. However, addition of hole scavenger increases the activity many folds and complete removal of Pb(2+) and Cd(2+) was possible in 60 min of reaction using synthesized catalysts. Among all the organic hole scavengers used, sodium formate is found to be the most active one. Interestingly quite high metal removal (89%) is also observed in presence of visible light within 60 min of reaction. Thus the above study indicates that the presence of certain oxides in low quantity (10 wt%) with titania can facilitates the photocatalytic process selectively in UV as well as visible light.