Extraction of Uranium(VI) by N-Octanoylpiperidine in Toluene

The extraction of uranium(VI) from nitric acid by N-octanoylpiperidine (OPPD) in toluene has been investigated at varying concentrations of nitric acid, extractant, salting-out agent LiNO₃ and at different temperatures. The mechanism of extraction is discussed in the light of the results obtained. The extracted species have also been investigated using FT-IR spectrometry. The related thermodynamic functions were calculated.     

Separation of Uranium(VI) by Extraction with Dibutylditiophosphoric Acid

The extraction of uranium(VI) from aqueous solutions with dibutylditiophosphoric acid in organic solvents was studied. The influence of different factors as pH of the aqueous phase, extractant concentration and nature of solvent was investigated in order to find the optimum conditions for separation of metal from aqueous nitrate solutions. The effect of neutral donor extractants was also searched and the efficiency of the extraction was calculated.     

Complexation of Uranium(VI) by Gluconate in Alkaline Solutions

Gluconate (C₆H₁₁O₇) is a polyhydroxycarboxylic acid that can be assumed as a representative model compound for a wide variety of additives in cement formulations. It can play an important role in the cementitious environments characteristic of radioactive waste disposal sites, as actinides (such as U(VI)) may form stable complexes with gluconate. As a consequence, the presence of the organic ligand can lead to an enhancement of actinide mobility. The results presented in this work show that gluconate increases significantly the uranium solubility at pH_c = 12; the study of U(VI) speciation in alkaline solutions is complex, mainly due to formation of sparingly soluble uranates of varying compositions (e.g. sodium and potassium uranates). UV–Vis measurements in the alkaline pH range have been used to determine the stability constant for the formation of a 1:1 U(VI):gluconate complex. The results obtained with spectroscopic techniques allow explaining the results from solubility experiments, from both over- and under-saturation conditions.     

Polarography of Uranium (VI)-Arsonoacetate Complex

The complexation of uranium (VI) with arsonacetic acid has been studied polarographically. A two-step polarographic wave was obtained at lower pH value. The dissociation reaction of the complex was deduced from the kinetic current of the prewave. The asymmetry to half-wave of polarograms was interpreted on the basis of polynuclear complex. The limits of reversibility, chelation, polymerization and precipitation of the complex, which are functions of pH and ligand concentration, were shown.     

Uranium(VI) adsorption on montmorillonite colloid

Journal of Radioanalytical and Nuclear Chemistry - Montmorillonite colloid was synthesized and characterized and the adsorption of U(VI) on colloid as a function of contact time, temperature,...     

Photoluminescence of Uranium(VI): Quenching Mechanism and Role of Uranium(V)

The photoluminescence of uranium(VI) is observed typically in the wavelength range 400–650 nm with the lifetime of several hundreds μs and is known to be quenched in the presence of various halide ions (case A) or alcohols (case B). Here, we show by density functional theory (DFT) calculations that the quenching involves an intermediate triplet excited state that exhibits uranium(V) character. The DFT results are consistent with previous experimental findings suggesting the presence of photoexcited uranium(V) radical pair during the quenching process. In the ground state of uranyl(VI) halides, the ligand contributions to the highest occupied molecular orbitals increase with the atomic number (Z) of halide ion allowing larger ligand‐to‐metal charge transfer (LMCT) between uranium and the halide ion. Consequently, a larger quenching effect is expected as Z increases. The quenching mechanism is essentially the same in cases A and B, and is driven by an electron transfer from the quencher to the UO₂²⁺ entity. The relative energetic stabilities of the triplet excited state define the “fate” of uranium, so that in case A uranium(V) is oxidized back to uranium(VI), while in case B uranium remains as pentavalent.     

Uranium(VI) removal from aqueous solutions by a chelating fiber

Journal of Radioanalytical and Nuclear Chemistry - A chelating fiber (CF), containing amine and hydroxyl groups, has been characterized and used as an adsorbent for the removal of U(VI) from...     

Spectrophotometric Determination of Uranium(VI) with Chlorophosphonazo-mN by Flow Injection Analysis

Abstract

A sensitive and selective spectrophotometric flow injection analysis (FIA) method with chlorophosphonazo-mN has been developed for the determination of uranium(VI) in standard ore samples. Most of interfering ions are effectively eliminated by the masking reagent of diethylenetriaminepentaacetic acid (DTPA). In the U(VI)-chlorophosphonazo-mN system, the maximum absorption wavelength is at 680 nm and Beer's law is obeyed in the range of 1 to 15 μg ml^?1. The correlation coefficient of the calibration curve is 0.9998, the sampling frenquency is 60 h^?1, and the detection limit for uranium(VI) is 0.5 μg ml^?1. The composition of the U(VI)-chlorophosphonazo-nN complex was established to be 1:2 by flow-through spectrophotometric and conventional molar ratios methods.     

Uranium(VI) sequestration by polyacrylic and fulvic acids in aqueous solution

Stability data on the formation of dioxouranium(VI) species with polyacrylic (PAA) and fulvic acids (FA) are reported with the aim to define quantitatively the sequestering capacity of these high molecular weight synthetic and naturally occurring ligands toward uranium(VI), in aqueous solution. Investigations were carried out at t = 25 °C in NaCl medium at different ionic strengths and in absence of supporting electrolyte for uranyl–fulvate ( \textUO₂²⁺ {{\text{UO}}_{2}}^{2+} –FA) and uranyl–polyacrylate ( \textUO ₂ ²⁺ {{\text{UO}}_{ 2}}^{ 2+ } –PAA, PAA MW 2 kDa) systems, respectively. The experimental data are consistent with the following speciation models for the two systems investigated: (i) UO₂(FA₁), UO₂(FA₁)(FA₂), UO₂(FA₁)(FA₂)(H) for \textUO ₂ ²⁺ {{\text{UO}}_{ 2}}^{ 2+ } –fulvate (where FA₁ and FA₂ represent the carboxylic and phenolic fractions, respectively, both present in the structure of FA), and (ii) UO₂(PAA), UO₂(PAA)(OH), (UO₂)₂(PAA)(OH)₂ for \textUO ₂ ²⁺ {{\text{UO}}_{ 2}}^{ 2+ } –polyacrylate. By using the stability data obtained for all the complex species formed, the uranium(VI) sequestration by PAA and FA was expressed by the pL₅₀ parameter [i.e. the −log(total ligand concentration) necessary to bind 50% of uranyl ion] at different pH values. A comparison between pL₅₀ values of FA and PAA and some low molecular weight carboxylic ligands toward uranyl ion is also given.     

Determination of the Uranium(VI) and ‐(IV) Species in Uranium Ores

The determination of the two species of uranium(VI and IV) present in 6 uranium ores was studied in relation to the chemical and mineralogical composition, humidity, and pH of the samples taken over from the mine. X‐ray diffraction studies, performed on the uranium ores in powder form allowed to establish their mineralogical composition. Thechemical analysis pointed out the presence, besides the two uranium species, of some microelements able to influence the U^VI/U^IV ratio in minerals and to leach out U^VI as uranyl ions from the corresponding minerals.     

Ultrafast concentration and speciation of chromium(III) and (VI)

There is an increasing need to know the concentrations of chromium(III) and (VI) separately rather than only the total chromium content. A method is described for accomplishing this very quickly using only low-cost, portable equipment. Two small, resin-loaded extraction disks are placed one on top of the other in a plastic holder. Then a syringe containing the aqueous sample is attached to the holder and the sample is pushed through the disks. In a matter of seconds, all of the chromium(VI) is retained on the top anion-exchange disk and chromium(III) is extracted by the second cation-exchange disk. The concentrations on each disk are several hundredfold higher than they were in the original sample. The amounts of chromium(III) and (VI) extracted are measured directly on the surface of the respective disks by diffuse reflectance spectroscopy (DRS). Despite the low molar absorptivity of chromium(III) in aqueous solution, the concentration on the upper most layer on the extraction disk is high enough to permit the determination of chromium(III) in samples at the low mg/L range. Chromium(VI) can also be determined at low to sub-mg/L concentrations. A study of the cation-exchange disks was undertaken to compare the performance characteristics of disks containing sulfonated resins and those with iminodiacetate functionality. In addition, data are presented to show the effects of heating the iminodiacetate disks after the initial extraction. The disks were heated in hot water for 15-30 min to complete the slow complexation reaction on the surface.     

The Extraction of Uranium(VI) with n-Octyldecylsulfoxides (ODSO)-Toluene

The liquid-liquid extraction of uranium(VI) from aqueous nitric acid with n-octyldecylsulfoxide (ODSO) in toluene has been studied over a wide range of conditions. The extracted species appears to be UO₂(NO₃)₂·2ODSO. The extraction increased with increasing nitric acid concentration up to 2.0 mol/l and then decreased. Extraction also increased with increasing extractant concentration. The influence of temperature, salting-out agent concentration and complex anion concentration on the extraction equilibrium were also investigated, and the enthalpy of the extraction reaction was calculated.     

Two‐Electron Reductive Carbonylation of Terminal Uranium(V) and Uranium(VI) Nitrides to Cyanate by Carbon Monoxide

Two‐electron reductive carbonylation of the uranium(VI) nitride [U(Tren^TIPS)(N)] ( 2 , Tren^TIPS=N(CH₂CH₂NSiiPr₃)₃) with CO gave the uranium(IV) cyanate [U(Tren^TIPS)(NCO)] ( 3 ). KC₈ reduction of 3 resulted in cyanate dissociation to give [U(Tren^TIPS)] ( 4 ) and KNCO, or cyanate retention in [U(Tren^TIPS)(NCO)][K(B15C5)₂] ( 5 , B15C5=benzo‐15‐crown‐5 ether) with B15C5. Complexes 5 and 4 and KNCO were also prepared from CO and the uranium(V) nitride [{U(Tren^TIPS)(N)K}₂] ( 6 ), with or without B15C5, respectively. Complex 5 can be prepared directly from CO and [U(Tren^TIPS)(N)][K(B15C5)₂] ( 7 ). Notably, 7 reacts with CO much faster than 2 . This unprecedented f‐block reactivity was modeled theoretically, revealing nucleophilic attack of the π* orbital of CO by the nitride with activation energy barriers of 24.7 and 11.3 kcal mol^?1 for uranium(VI) and uranium(V), respectively. A remarkably simple two‐step, two‐electron cycle for the conversion of azide to nitride to cyanate using 4 , NaN₃ and CO is presented.     

On-line pre-reduction of Se(VI) by thiourea for selenium speciation by hydride generation

In this study, thiourea (TU) was novelly developed as a reduction reagent for on-line pre-reduction of selenium(VI) before conventional hydride generation (HG) by KBH₄/NaOH–HCl. After TU on-line pre-reduction, the HG efficiency of Se(VI) has been greatly improved and because even higher than that of the same amount of Se(IV) obtained in the conventional HG system. The possible pre-reduction mechanism is discussed. The detection limit (DL) of selenate reaches 10 pg mL^− 1 when using on-line TU pre-reduction followed by HG atomic fluorescence detection. When TU pre-reduction followed by HG is used as an interface between ion-pair high performance liquid chromatography and atomic fluorescence spectrometry, selenocystine, selenomethionine, selenite and selenate can be measured simultaneously and quantitatively. The DLs of these are 0.06, 0.08, 0.05 and 0.04 ng mL^− 1, respectively, and the relative standard deviations of 9 duplicate runs for all the 4 species are less than 5%. Furthermore, it was successfully applied to Se speciation analysis of cultured garlic samples, and validated by determination of total selenium and selenium species in certified reference material NIST 1946.     

Uranium(VI) extraction by Winsor II microemulsion systems using trialkyl phosphine oxide

Summary The parameters affecting the formation of the microemulsion were investigated and the microemulsion region was determined. The extraction of uranium(VI) from HNO₃ solution into a water in oil microemulsion was studied. The effects of the concentration of extractant (TRPO), the volume ratio of oil to water and the acidity of outer water phase on the extraction equilibrium of uranium(VI) are discussed and the appropriate conditions are obtained. The result showed the microemulsion has great efficiency for uranium(VI) extraction.     

Europium (III) and Uranium (VI) complexation by natural organic matter (NOM): Effect of source

For the safe long‐term storage of high‐level radioactive waste (HLW), detailed information about geo‐chemical behavior of radioactive and toxic metal ions under environmental conditions is important. Natural organic matter (NOM) can play a crucial role in the immobilization or mobilization of these metal ions due to its complexation and colloid formation tendency. In this study, the complexation of europium (as chemical homologue of trivalent actinides such as americium) and uranium (as main component of HLW) by ten humic acids (HA) from different sources and Suwannee NOM river extract has been analyzed. Capillary electrophoresis in combination with inductively coupled plasma mass spectrometry has been used for the evaluation of complex stability constants log β. In order to determine the complex stability constants a conservative single site model was used in this study. In dependence of their source and thus of NOM structure the log β values for the analyzed humic acids are in the range of 6.1–7.0 for Eu(III) and 5.2–6.4 for U(VI) (UO₂²⁺), respectively. In contrast to the results for HA the used Suwannee river NOM reveals log β values in the range of nearly two orders of magnitude lower (4.6 for Eu³⁺ and 4.5 for UO₂²⁺) under the geochemical conditions applied in this study.     

Extraction Mechanism of Uranium(VI) with Di(1-Methylheptyl)Phosphoric Acid

The extraction of U(VI) from nitric acid solutions with di-(1-methylheptyl) phosphoric acid has been investigated. The dependence on nitric acid concentration, DMHPA concentration and temperature has been considered and the infra-red spectra of extracted species and extractant were recorded. The mechanism of extraction is discussed in the light of the results obtained.     

Surface speciation of Cd(II) and Pb(II) on kaolinite by XAFS spectroscopy

Little spectroscopic evidence exists in the literature describing the surface complexation of cadmium (Cd) and lead (Pb) on kaolinite, the dominant clay mineral present in highly weathered soils of tropical and humid climates. X-ray absorption fine structure (XAFS) spectroscopy data at the Cd K and Pb L(III) edges were collected on Cd- and Pb-sorbed kaolinite samples and compared to a suite of reference materials including Pb and Cd sorbed on amorphous (am-)gibbsite. Cadmium formed dominantly (>75%) outer sphere complexes on kaolinite and a small fraction of CdOHCl complexes. In contrast Cd adsorbed as an inner sphere complex on gibbsite, suggesting that the Si tetrahedral sheet hindered Cd sorption to the Al octahedral sheet on kaolinite. Lead formed polymeric complexes, which bonded to kaolinite via edge sharing with surface Al octahedra. Two distinct Pb-Al edge-sharing distances on am-gibbsite, as opposed to one on kaolinite, suggested a similar steric hindrance effect for the surface complexation of polymeric Pb complexes on kaolinite. The results of this study show that the Si tetrahedral sheet limited the surface complexation of Cd and Pb on kaolinite, elevating kaolinite's permanent negative charge properties in retaining these heavy metals at its surface.     

Back-Extraction of Uranium(VI) from Organophosphoric Acid with Hydrazine Carbonate

The back-extraction of uranium(VI) from di(2-ethylhexyl)phosphoric acid (HDEHP) and diisodecylphosphoric acid (DIDPA) was studied by using hydrazine carbonate as back-extractant. U(VI) was back-extracted from n-dodecane solutions of 0.5M HDEHP - 0.2M TBP and 0.5M DIDPA - 0.1M TBP by hydrazine carbonate. The distribution ratios were decreased with an increase of hydrazine carbonate concentration. The back-extraction equilibria were expressed by slope analysis in consideration of neutralization between the extractant (DIDPA, HDEHP) and hydrazine carbonate, which occurred quantitatively during the back-extraction.